SlideShare a Scribd company logo

Call processing and handover.eng

Neelabh Krishna, profile picture
Neelabh Krishna

This document provides a summary of key concepts in LTE network architecture and protocols: 1) It describes the LTE network architecture including nodes like the eNB, MME, S-GW and P-GW as well as interfaces like S1, S3, S6a and S11. 2) It explains the protocol stack used in the UE and network, covering layers like PDCP, RLC, MAC and PHY. 3) It outlines the main software blocks and functions of the eNB including call processing, O&M, and packet forwarding.

Technology
1 of 73
Downloaded 14 times
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
1/73 Customer Training Center Jaeho, Lee Distribution EnglishED01
2/73 CALL S/W Overview
3/73 Network Architecture UTRAN GERAN SGSN MME E-UTRANUE Serving Gateway HSS LTE-Uu S1-U S1-MME S3 S6a S11 S10 S4 S12 PDN Gateway PCRF Operator’s IP Services Ex) IMS. PSS etc S5 SGi Gx Rx LTE Network Architecture
4/73 Protocol Stack UE Control Plane UE User Plane L1 MAC RLC PDCP RRC NAS L1 MAC RLC PDCP RRC L1 L2 IP SCTP S1-AP Relay L1 L2 IP SCTP S1-AP L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C NAS LTE-Uu S1-MME S11 S5/S8a UE eNB MME S-GW P-GW SGi L1 MAC RLC PDCP IP App L1 MAC RLC PDCP L1 L2 UDP/IP GTP-U Relay LTE-Uu S1-U S5/S8 L1 L2 UDP/IP GTP-U L1 L2 UDP/IP GTP-U Relay L1 MAC UDP/IP GTP-U IP UE eNB S-GW P-GW
5/73 eNB Software Architecture • CPS (Call Processing Software): LTE Control & Bearer Protocol processing • OAM (Operation and Maintenance): eNB Operation and Maintenance • MW (Middleware): IPC and Redundancy function • IPRS (IP Routing Software): Routing protocol operation • NP SW (Network Processor Software): Packet forwarding function • OS (Operating System): Embedded Linux • DD (Device Driver): initializing and setting the devices
6/73 Call Software Blocks (1/3) ECCB GTPB PDCB RLCB MACB Other eNB EPC PHY UE S1-c X2-c S1-u X2-u ECS (eNB Control Subsystem) EDS (eNB Data Subsystem) LTE eNB LEGEND : (UDP port)Control (IPC) Traffic SCTB ECMM ESCM ERCM ERRM ECCM EHCM Uu ECCB ECMB Interface
7/73 Call Software Blocks (2/3) ECMB (eNB Common Management Block) Initiate eNB and set the common channel Transmit system information for initiating UE Load Control for cell and system overload ECCB (eNB Call Control Block) Radio Resource Management, Call Admission Control RRC/S1-AP ASN.1 Interface, X2-AP ASN.1 Interface Control the basic call access, S1-AP Paging, Handover call control, Call Trace SCTB (Stream Control Transmission protocol Block) S1-C/X2-C SCTP Interface (Association setup/release), S1/X2 AP message Transmission
8/73 Call Software Blocks (3/3) GTPB (GPRS Tunneling Protocol Block) GPRS(General Packet Radio Service) Tunneling Protocol for data access on S1-U or X2-U. PDCB (Packet Data Convergence protocol Block) Header compression and decompression on IP packet stream, Ciphering, Integrity DL/UL data forwarding on Handover PDCP sequence number maintenance, Timer based PDCP SDU discard RLCB (Radio Link Control Block) Radio Link control and ARQ(Automatic Repeat Request) RLC SDU concatenation/segmentation/reassemble, In sequence delivery, RLC re- establishment RLC PDU re-segmentation, Paging MACB (Medium Access Control Block)
9/73 Main ID and S1/X2 Procedure
10/73 E-UTRAN Identifiers (1/3) eNB-Related ID
11/73 E-UTRAN Identifiers (2/3) UE-Related ID on S1 (for UE-associated signaling) UE-Related ID on X2 (for X2 Handover)
12/73 E-UTRAN Identifiers (3/3) Other EPS IDs
13/73 S1 Interface: Procedures (1/2) Class 1 Procedures Sender expects response from receiver
14/73 S1 Interface: Procedures (2/2) Class 2 Procedures Sender does not expect response
15/73 X2 Interface: Procedures Class 1 Procedures Class 2 Procedures
16/73 Basic Call Procedure
17/73 S1 Setup between eNB and MME Objective To setup the S1AP connection Exchange configuration information
18/73 X2 Setup between eNB and eNB Objective To setup the X2AP connection Exchange configuration information Neighbor PCI info is exchanged for supporting Automatic PCI Selection
19/73 Attach Procedure (1/2) UE Source eNB MME S-GW EPC 4. Initial UE Message(+ Attach Requet) NAS procedure( Nas security, Authentication ) 7. Initial Context Setup Request (+ Attach Accept) 2. RRC Connection Setup 1. RRC Connection Request 3. RRC Connection Setup Complete 5. Create Session Request 6. Create Session Response
20/73 Attach Procedure (2/2) UE Source eNB MME S-GW EPC 10. UE Capbility Info Indication 13. RRC Connection Reconfiguration 8. UE Capability Enquiry 9. UE Capability Information 12. Security Mode Complete 11. Security Mode Command 14. RRC Connection Reconfiguration Complete 15. Initial Context Setup Response 18. Modify Bearer Request 19. Modify Bearer Response 16. Uplink Information Transfer 17. Uplink NAS Transport Uplink Data
21/73 Detach Procedure(1/2) – w/o RRC Connection UE Source eNB MME S-GW EPC 4. Initial UE Message(+ Detach Requet) 9. UE Context Release Command 2. RRC Connection Setup 1. RRC Connection Request 3. RRC Connection Setup Complete (+ Detach Request) 6. Delete Session Response 7. Downlink NAS Transport (+ Detach Accept) 8. Downlink Information Transfer(+ Detach Accept) 10. RRC Connection Release 11. UE Context Release Complete 5. Delete Session Request
22/73 Detach Procedure (2/2) – w RRC Connection UE Source eNB MME S-GW EPC 2. Uplink NAS Transport(+ Detach Requet) 7. UE Context Release Command 1. Uplink Information Transfer (+ Detach Request) 4. Delete Session Response 5. Downlink NAS Transport (+ Detach Accept) 6. Downlink Information Transfer(+ Detach Accept) 8. RRC Connection Release 9. UE Context Release Complete 3. Delete Session Request
23/73 LTE Measurement Report Events Intra-LTE measurement events Event A1 - Serving becomes better than threshold. => release the measurement gap. Event A2 - Serving becomes worse than threshold. => setup measurement gap. Event A3 - Neighbour becomes offset better than serving. => trigger Intra-LTE handover => execute ANR Event A4 - Neighbour becomes better than threshold. Event A5 - Serving becomes worse than threshold1 and neighbour becomes better than threshold2. Inter-RAT measurement events Event B1 - Inter RAT neighbour becomes better than threshold. Event B2 - Serving becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2. => trigger Inter-RAT handover
24/73 Measurement Signaling & Info MeasurementReport UE EUTRAN Measurement Reporting from the UE Measurement Report message has Physical Cell Id (PCI) info of neighbor cell. Execute handover using PCI of Measurement Report message received from eNB. In case of neighbor cell of CDMA2000, preRegistrationStatusHRPD information is included requested interworking- HRPD. Cell Global Id (CGI) information is included as requested from eNB. ANR function is executed using CGI information from UE on eNB.
25/73 Handover Classification Intra-RAT Handover Intra-eNB Handover Inter-eNB Handover over X2 Inter-eNB Handover over S1 (Intra-MME) Inter-eNB Handover over S1 (Inter-MME) Inter-RAT Handover CDMA2000, GERAN, UTRA, etc.
26/73 Handover Procedure [signaling]
27/73 Handover Procedure [event-triggering]
28/73 Handover Procedure [measurement] RSRP [dBm] : Reference Signal Received Power Absolute value, not related to Payload RSSI [dBm] : Received Signal Strength Indicator Received power of center 6RB (1.08MHz) Directly proportional to Payload RSRQ [dB] : RSRP/RSSI ratio Inversely proportional to Payload – Using for handover of cell loading frequency 0 RSSI [dBm] : 6RB power (6RB=72subcarrier=1.08MHz) BW = 10MHz RSRP [dBm] : carrier powerRS carrier data carrier
29/73 Handover Interruption Time
30/73 Intra-LTE / Inter-eNB X2 Handover UE Source eNB MME S-GW EPC 1. MeasurementReport Target eNB Downlink/Uplink data Downlink/Uplink data 3. HANDOVER REQUEST ACKNOWLEDGE 5. SN STATUS TRANSFER 4. RRCConnection- Reconfiguration (mobilityControlinfo) Data forwarding 6. Synchronization/UL allocation and timing advance 7. RRCConnectionReconfigurationComplete Forwarded data Uplink data Forwarded data Downlink data Down/Uplink data Down/Uplink data Uplink data Downlink data 8. PATH SWITCH REQUEST 9. Modify Bearer Request End marker End marker 10. Modify Bearer Response11. PATH SWITCH REQUEST ACKNOWLEDGE 12. UE CONTEXT RELEASE 2. HANDOVER REQUEST
31/73 Intra-LTE / Inter-eNB S1 Handover (1/2) UE Source eNB MME S-GW EPC Target eNB Downlink/Uplink data Downlink/Uplink data 3. HANDOVER REQUEST 5. Create Indirect Data Forwarding Tunnel Request 8. RRCConnection- Reconfiguration (mobilityControlinfo) 1) Direct data forwarding 1. Decision to trigger a relocation via S1 2. HANDOVER REQUIRED Indirect data forwarding 6. Create Indirect Data Forwarding Tunnel Response 7. HANDOVER COMMAND 9. eNB STATUS TRANSFER 10. MME STATUS TRANSFER 2) Indirect data fowarding 11. Detach from old cell/Synchronize to new cell 12. RRCConnectionReconfigurationComplete Forwarded data Uplink data Uplink data 4. HANDOVER REQUEST ACKNOWLEDGE
32/73 Intra-LTE / Inter-eNB S1 Handover (2/2) UE Source eNB MME S-GW EPC Target eNB Downlink data Downlink data End marker End marker 13. HANDOVER NOTIFY 14. Modify Bearer Request 15. Modify Bearer Response Forwarded data 16. Tracking Area Update procedure 17. UE CONTEXT RELEASE COMMAND 18. UE CONTEXT RELEASE COMPLETE 19. Delete Indirect Data Forwarding Tunnel Request 20. Delete Indirect Data Forwarding Tunnel Response Downlink/Uplink data Downlink/Uplink data
33/73 Basic Parameters Setting
34/73 MME Configuration (1/2) CHG-MME-CONF : Setup information related MME Input the MME’s status connected S1 interface CLI Command
35/73 SRB RLC Configuration (1/2) CHG-SRB-QCI : Setup QoS information on SRB CLI Command
36/73 SRB RLC Configuration (2/2) CHG-SRB-RLC : Setup RLC information on SRB CLI Command The timer is for the prohibition of transmission of STATUS_STATUS on received-Entity(AM_RLC)
37/73 SRB MAC Configuration (1/4) CHG-LOCH-INF : Setup Logical channel information per QCI CLI Command
38/73 SRB MAC Configuration (2/4) CHG-TRCH-INF : Setup Transport channel information per Cell CLI Command Marking cell index for changing or displaying
39/73 SRB MAC Configuration (3/4) CHG-DRX-INF : Setup DRX information per Cell CLI Command
40/73 SRB MAC Configuration (4/4) CHG-DPHY-SPS Change parameters for the operating of Dedicated semiPersistScheduling. Cell_NUM : 0 ~ 5 PO_NOMINAL_PUSCHPERSISTENT: SPS Po parameter using power control is -126 ~ 24, default: -80 PO_UEPUSCHPERSISTENT: SPS Po parameter’s range on Power control per UE: - 8 ~7, default: 0 CHG-DPHY-PUSCH Change parameters for Dedicated PUSCH operaiton. Cell NUM: 0 ~ 5 BETA_OFFSET_ACKINDEX: Set the value of multiplexing ACK/NACK and PUSCH. Range: 0 ~ 15, default: 8 BETA_OFFSET_RIINDEX: Set the value of multiplexing RI and PUSCH Range: 0 ~ 15, default: 5 BETA_OFFSET_CQIINDEX: Set the value of multiplexing CQI and PUSCH Range: 0 ~ 15, default: 11
41/73 SRB MAC Configuration (4/4) CHG-ULPWR-CTRL Change parameters for the operating of Dedicated Uplink Power Control. Cell Number: 0 ~5 PO_UE_PUSCH: non-persistent scheduling Po parameter using PUSCH Power control per UE. Range: -8 ~ 7, default: 0 DELTA_MCSENABLED: Usage possibility for different MCS on Power offset Range: ci_en0/ci_en1/, default: ci_en0 ACCUMULATION_ENABLE: TPC Mode(accumulation mode/absolute mode) Range: 0 ~ 1, default: 1(accumulation mode) PO_UE_PUCCH: Po parameter(-8 ~ 7), default: 0 P_SRSOFFSET: This index is indicating the power offset of PUSCH and SRS: 0~15, default:7
42/73 SRB MAC Configuration (4/4) CHG-CQI-REPORTING Change parameters for the operating CQI Reporting TRANSMISSION_MODE: ci_tm1,2,3,4, ~ 8. default null – Mode 1: Single antenna port, port 0 – Mode 2: Transmit diversity – Mode 3: Large-delay CDD – Mode 4: Closed-loop spatial multiplexing – Mode 5: MU-MIMO – Mode 6: Closed-loop spatial multiplexing, single layer – Mode 7: Single antenna port, UE-specific RS (port 5) – Mode 8 (new in Rel-9): Single or dual-layer transmission with UE-Specific RS Port 7 and/or 8 Select CQI on Wideband/subband.
43/73 SRB MAC Configuration (4/4) CHG-DPHY-ULSRS Change the parameters for operating of Dedicated Uplink RS. Cell_NUM: 0 ~ 5 SRS_HOPPING_BANDWIDTH: Set the Area that is became “hopping status of Sounding RS. ci_hbw0 ~ hbw3, default: ci_hbw0 DURATION: Set the duration of sounding RS. If the value is ‘True’, the transmission of Sounding RS is not stopped until disabled. If the value is ‘False’ , transmit one time. (Range: 0 ~1), default vlalue: 1 CHG-DPHY-SR Change the parameters for operating of Dedicated Scheduling Request. Cell NUM: 0 ~5 DSR_TRANS_MAX: Set the maximum transmittable counts of scheduling requests until received PUSCH resource on UE.(ci_dsr_TransMax_n4 ~ 8,16,32,64) , default value: ci_dsr_TransMax_n64
44/73 DRB PDCP Configuration (1/3) CHG-PDCP-INF : Set the PDCP information per QCI CLI Command
45/73 DRB PDCP Configuration (2/3) CHG-ROHC-INF : Setup ROHC information per QCI CLI Command
46/73 DRB PDCP Configuration (3/3) CHG-SECU-INF : Set the Security Algorithm information CLI Command
47/73 DRB RLC Configuration CHG-RLC-INF : Set the RLC information per QCI CLI Command
48/73 Neighbor Configuration
49/73 Neighbor Configuration (1/7) The value is different for opeartors. Input PLMN Id of eNB operator. Input the value same as PLMN ID of eNB. Creation EUTRA Neighbor – PLD update or manually input with CLI on LSM CLI Command Create information of E-UTRA cells located near a base station
50/73 Neighbor Configuration (2/7) Parameter Description Range Value Cell Num Cell number of Base Station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP eNB ID Neighbor eNB Identity 20 or 28 BITS - Local Cell ID Neighbor local cell ID 0 ~ 255 - eNB Type Neighbor eNB type Macro or Home Macro eNB MCC Mobile Country Code of Neighbor eNB - Ex) Korea: 450 eNB MNC Mobile Network Code of Neighbor eNB - Physical Cell ID Neighbor cell PCI 0 ~ 503 - TAC Neighbor cell TAC 2 BYTES - PLMNs PLMN Lists supported neighbor cell - -
51/73 Neighbor Configuration (3/7) Parameter Description Range Value EARFCN UL Uplink EARFCN 0 ~ 65535 - EARFCN DL Downlink EARFCN 0 ~ 65535 - Bandwidth UL Uplink Bandwidth n6, n15, n25, n50, n75, n100 It’s different per operators. Bandwidth DL Downlink Bandwidth n6, n15, n25, n50, n75, n100 It’s different per operators. Individual Offset Cell Individual Offset adaptable neighbor cell. dB-24, dB-22, dB-20, dB-18, dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-4, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5, dB6, dB8, dB10, dB12, dB14, dB16 dB18, dB20, dB22, dB24 dB0 Qoffset Cell Cell Quality Offset adaptable neighbor cell. Same dB0 Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
52/73 Neighbor Configuration (4/7) CDMA2000 1xRTT Neighbor creation – input remote neighbor widow or CLI CLI Command Create the information of CDMA2000 1xRTT Cells located near by a base station
53/73 Neighbor Configuration (5/7) Parameter Description Range Value Cell Num Cell number in base station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP SID CDMA2000 1xRTT SID 0 ~ 32767 - NID CDMA2000 1xRTT NID 0 ~ 65535 - Base ID CDMA2000 1xRTT Base ID 0 ~ 65535 - Band Class CDMA2000 1xRTT Band Class bc0, bc1, bc2, bc3, bc4, bc5, bc6, bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15, bc16, bc17 - ARFCN Neighbor cell’s ARFCN 0 ~ 2047 - PN Offset Neighbor cell’s PN Offset (CDMA2000’s PCI) 0 ~ 511 - Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
54/73 Neighbor Configuration (6/7) Creation CDMA2000 HRPD Neighbor – input remote neighbor widow or CLI CLI Command Create the information of CDMA2000 HRPD Cells located near by a base station
55/73 Neighbor Configuration (7/7) Parameter Description Range Value Cell Num Cell number in base station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP Color Code Neighbor Cell’s Color Code 0 ~ 255 - BSM ID Neighbor Cell’s BSM ID 0 ~ 63 - BSC ID Neighbor Cell’s BSC ID 0 ~ 1 - DPSS ID Neighbor Cell’s DPSS ID 0 ~ 7 - BTS ID Neighbor Cell’s BTS ID 0 ~ 2047 - Sector ID Neighbor Cell’s Sector ID 0 ~ 7 - Band Class Neighbor Cell’s Band Class bc0, bc1, bc2, bc3, bc4, bc5, bc6, bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15, bc16, bc17 - ARFCN Neighbor Cell’s ARFCN 0 ~ 2047 - PN Offset Neighbor Cell’s PN Offset (CDMA2000’s PCI) 0 ~ 511 - Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
56/73 Handover Configuration
57/73 Handover Event Configuration – Event A3 (1/3) Event A3 : Use for Intra LTE Handover and SON ANR - A3PurposeInraLteHandover - A3PurposeReportStrongestCells - Unit: dBm - Actual value: PLD value * 0.5 - RSRP or RSRQ - sameAsTriggerQuantity or both Change EUTRA A3 Criteria information CLI Command
58/73 Handover Event Configuration – Event A3 (2/3) Parameter Description Range Value Cell Num Cell number in base station 0~5 N/A Purpose The purpose of Event A3 usage 0: A3PurposeIntraLteHandov er 1: A3ReportStrongestCells 2: A3PurposeSpare_1 3: A3PurposeSpare_2 N/A Active State The status of Event A3 0: Inactive 1: Active Active A3 Offset RSRP threshold value using the condition of EUTRA measurement report triggering for Event A3 . (unit: dBm) -30 ~ 30 4 A3 Report On Leave Whether or not to report in case of Event A3 leaving condition TRUE or FALSE FALSE Hysteresis The entry/leave condition on Event triggered reporting. (unit: dB) 0 ~ 30 0
59/73 Handover Event Configuration – Event A3 (3/3) Parameter Description Range Value Time To Trigger The sufficient time in specific criteria when UE try to trigger the measurement report . (unit: ms) ms0, ms40, ms64, ms80, ms100, ms128, ms160, ms256, ms320, ms480, ms512, ms640, ms1024, ms1280, ms2560, ms5120 ms480 Trigger Quantity The quantity information used for evaluating the triggering condition for Events. RSRP or RSRQ RSRP Report Quantity The quantity information including Measurement Report Message. SamsAsTriggerQuantity or Both SameAsTriggerQuantity Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 8 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r8
60/73 Handover Event Configuration – Event B2 (1/4) Event B2 : Usage for Inter RAT(CDMA2000 1xRTT) Handover CLI Command Change CDMA2000 1xRTT B2 Criteria Information
61/73 Handover Event Configuration – Event B2 (2/4) Event B2 : Usage for Inter RAT(CDMA2000 HRPD) Handover CLI Command Change CDMA2000 HRPD B2 Criteria Information
62/73 Handover Event Configuration – Event B2 (3/4) Parameter Description Range Value Cell Num Cell number in base station 0~5 N/A Purpose The purpose of Event B2 Usage 0: B2PurposeInterRatHandover 1: B2PurposeSpare_1 3: B2PurposeSpare_2 N/A Active State The status of Event B2 0: Inactive 1: Active Active B2 Threshold1 (RSRP) RSRP threshold value using the condition of EUTRA measurement report triggering for Event B2 . 0 ~ 97 70 B2 Threshold1 (RSRQ) RSRP threshold value using the condition of EUTRA measurement report triggering for Event B2. 0 ~ 34 10 B2 Threshold2 CDMA 2000 The threshold value using the condition of CDMA2000 HRPD measurement report triggering for Event B2. 0 ~ 63 20 Hysteresis The entry/leave condition on Event triggered reporting. (unit: dB) 0 ~ 30 0
63/73 Handover Event Configuration – Event B2 (4/4) Parameter Description Range Value Time To Trigger The sufficient time in specific criteria when UE try to trigger the measurement report. (unit: ms) ms0, ms40, ms64, ms80, ms100, ms128, ms160, ms256, ms320, ms480, ms512, ms640, ms1024, ms1280, ms2560, ms5120 ms80 Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 1 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r1 Trigger Quantity EUTRA The quantity information used for evaluating the condition of EUTRA event triggering. RSRP or RSRQ RSRP
64/73 Periodic Report Configuration – Periodic (1/4) Periodic Report : Usage for ICIC, SON ANR. CLI Command Change EUTRA Periodic Criteria Information
65/73 Periodic Report Configuration – Periodic (2/4) Periodic Report : Usage for interworking CDMA2000 1xRTT in the future. Change CDMA2000 1xRTT Periodic Criteria Information CLI Command
66/73 Periodic Report Configuration – Periodic (3/4) Periodic Report: Usage for interworking CDMA2000 HRPD in the future. CLI Command Change CDMA2000 HRPD Periodic Criteria Information
67/73 Periodic Report Configuration – Periodic (4/4) Parameter Description Range Value Purpose The purpose of configuration on Periodic measurement reporting. PeriodicalPurposeReportStrongestCells PeriodicalPurposeReportStrongestCellsForSON PeriodicalPurposeReportCGI N/A Active State The operation status of Periodic report. 0: Inactive 1: Active Inactive Trigger Quantity (EUTRA Only) The quantity information for evaluating the triggering condition for event. RSRP or RSRQ RSRP Report Quantity (EUTRA Only) The quantity information including Measurement report message. SamsAsTriggerQuantity or Both SameAsTrigg erQuantity Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 1 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r1
68/73 Handover Related Timers (1/2) X2, S1 Protocol Timers TX2RELOCprep, TX2RELOCoverall, TS1RELOCprep, TS1RELOCoverall CLI Command Change timer operation Information
69/73 Handover Related Timers (2/2) Parameter Description Range Value S1_PATH_SWITCH Target eNB sends Path Switch Request message to MME for S1 handover. The timer should be set when Target eNB is waiting Path Switch Request Acknowledge message from MME. 0 ~ 65535 (ms) 3000 S1 HANDOVER PREPARATION Source eNB sends Handover Request message to target eNB for S1 handover. The timer should be set when Source eNB is waiting Handover Request Acknowledge message from Target eNB. 0 ~ 65535 (ms) 5000 S1 RELOC OVERALL After the preparation procedure for S1 Handover, the timer should be set when Source eNB is waiting UE Context Release Command message from MME. 0 ~ 65535 (ms) 5000 S1 HANDOVER CANCEL Source eNB sends Handover Cancel message to MME for S1 handover. The timer should be set when Source eNB is waiting Handover Cancel Acknowledge message from MME. 0 ~ 65535 (ms) 5000 X2 HANDOVER PREPARATION Source eNB sends Handover Request message to target eNB for X2 handover. The timer should be set when Source eNB is waiting Handover Request Acknowledge message from Target eNB. 0 ~ 65535 (ms) 5000 X2 RELOC OVERALL After the preparation procedure for X2 Handover, the timer should be set when Source eNB is waiting UE Context Release message from target eNB. 0 ~ 65535 (ms) 5000 X2 STORE UE CONTEXT After X2 Handover, the MRO timer is working on target eNB. If target eNB receives RLF indication message while this timer is working on Target eNB, MRO statistic function is executed. 0 ~ 65535 (ms) 10000
70/73 Handover Restriction Configuration
71/73 eNB-controlled Handover Restriction (1/2) NO_HO If this option parameter is set to ‘TRUE’, It is not handover to the designated eNB. Set IP version 6 format for specific neighbor eNB IP address. CLI Command
72/73 eNB-controlled Handover Restriction (2/2) IS_HOALLOWED If this option parameter is set to ‘FALSE’, It is not handover to the designated cell. CLI Command Change E-UTRA cell’s information which is located at surrounding base station.
73/73

More Related Content

PDF
lte intra freq neighbour cells
sanjib_agrawala
 
PDF
Fast detection of number of antenna ports in lte system
eSAT Journals
 
PDF
Chap 4. call processing and handover.eng
sivakumar D
 
PDF
Lte x2-handover-sequence-diagram
Prashant Sengar
 
PDF
Utran example call_flows
sivakumar D
 
PPT
Rrc security procedure overview
khdesai80
 
PPT
Lte protocols
ece_narender
 
PPT
UMTS UTRAN Call Flow
Sujeet Kumar
 
lte intra freq neighbour cells
sanjib_agrawala
 
Fast detection of number of antenna ports in lte system
eSAT Journals
 
Chap 4. call processing and handover.eng
sivakumar D
 
Lte x2-handover-sequence-diagram
Prashant Sengar
 
Utran example call_flows
sivakumar D
 
Rrc security procedure overview
khdesai80
 
Lte protocols
ece_narender
 
UMTS UTRAN Call Flow
Sujeet Kumar
 

What's hot (20)

PDF
Call flow umts
Satish Jadav
 
PPT
Gsm fundamental-uku
sivakumar D
 
PPT
Ps call flow
Sudhir Kumar
 
PDF
Chap 3. e nb hardware description stc_ed01_0901
sivakumar D
 
PDF
Umts call-flow-scenarios overview
aritra321
 
PDF
3g umts-originating-call Call Flow
Eduard Lucena
 
PDF
Chap 5. lsm overview and practice
sivakumar D
 
PDF
54495209 umts-3 g-wcdma-call-flows
Noppadol Loykhwamsuk
 
PDF
Drive Test Nemo
toha ardi nugraha
 
PDF
3g umts-terminating-call
pkamoto
 
PDF
Best practices-lte-call-flow-guide
Morg
 
PDF
Bsc parameter
angga_telkom02
 
PDF
Lte principle
Hatim100
 
PPT
Mo cs call_flow
Sudhir Kumar
 
DOC
Complete umts call flow
sivakumar D
 
PDF
3 gpp lte-rlc (1)
Praveen Kumar
 
PPT
3 g rf_opt_process_ppt
Hatim100
 
PDF
SON,self optimized network
sivakumar D
 
PPT
Synchronization in SDH network
asifmatin
 
PDF
Wcdma kpi-analysis
a8us
 
Call flow umts
Satish Jadav
 
Gsm fundamental-uku
sivakumar D
 
Ps call flow
Sudhir Kumar
 
Chap 3. e nb hardware description stc_ed01_0901
sivakumar D
 
Umts call-flow-scenarios overview
aritra321
 
3g umts-originating-call Call Flow
Eduard Lucena
 
Chap 5. lsm overview and practice
sivakumar D
 
54495209 umts-3 g-wcdma-call-flows
Noppadol Loykhwamsuk
 
Drive Test Nemo
toha ardi nugraha
 
3g umts-terminating-call
pkamoto
 
Best practices-lte-call-flow-guide
Morg
 
Bsc parameter
angga_telkom02
 
Lte principle
Hatim100
 
Mo cs call_flow
Sudhir Kumar
 
Complete umts call flow
sivakumar D
 
3 gpp lte-rlc (1)
Praveen Kumar
 
3 g rf_opt_process_ppt
Hatim100
 
SON,self optimized network
sivakumar D
 
Synchronization in SDH network
asifmatin
 
Wcdma kpi-analysis
a8us
 
Ad

Similar to Call processing and handover.eng (20)

PDF
LTE Call Flow Procedures ,Intra LTE HO procedure
HarishkumarM34
 
PPT
OEA300020 LTE Signaling Flow ISSUE 1.00.ppt
marcobehaine
 
PDF
lte-x2-handover-sequence-diagram.pdf
AshishGupta360316
 
PDF
Lte call flows_att_best_practices_lte_pe
Hatim100
 
PDF
Lte system signaling procedures
tharinduwije
 
PPT
Overview and Basics of LTE
Chaitanya Tata, PMP
 
PDF
LTE: X2 interface
Schwannden Kuo
 
PDF
Lte imp
Prashant Sengar
 
PDF
LTE - protocol - signaling (4G course).pdf
mahmoudsafaei1987
 
PDF
LTE network: How it all comes together architecture technical poster
David Swift
 
PDF
Paper lte-interoperable
Prashant Sengar
 
PDF
Paper lte-protocol-signaling
Petrona Frensel M
 
PPT
Call flow and MS attach in LTE
Shashank Asthana
 
PDF
lte-enodeb-s1-startup-sib-rrc-connection.pdf
Junaid Alam
 
PPTX
43779871hgu-LTE-Voice-Call-Handover.pptx
banazjalil59
 
PDF
Lte attach-messaging
Praveen Kumar
 
PDF
Samsung_EnodeLSMR__Integration_Module__V1.pdf (1).pdf
RaviSharma1113
 
PDF
LTE Core Network
BSP Media Group
 
PDF
Lte overview titus
Nabil Al_Mutawakel
 
PPTX
20121129 lte basic procedures (2)
Debasish Sahoo
 
LTE Call Flow Procedures ,Intra LTE HO procedure
HarishkumarM34
 
OEA300020 LTE Signaling Flow ISSUE 1.00.ppt
marcobehaine
 
lte-x2-handover-sequence-diagram.pdf
AshishGupta360316
 
Lte call flows_att_best_practices_lte_pe
Hatim100
 
Lte system signaling procedures
tharinduwije
 
Overview and Basics of LTE
Chaitanya Tata, PMP
 
LTE: X2 interface
Schwannden Kuo
 
Lte imp
Prashant Sengar
 
LTE - protocol - signaling (4G course).pdf
mahmoudsafaei1987
 
LTE network: How it all comes together architecture technical poster
David Swift
 
Paper lte-interoperable
Prashant Sengar
 
Paper lte-protocol-signaling
Petrona Frensel M
 
Call flow and MS attach in LTE
Shashank Asthana
 
lte-enodeb-s1-startup-sib-rrc-connection.pdf
Junaid Alam
 
43779871hgu-LTE-Voice-Call-Handover.pptx
banazjalil59
 
Lte attach-messaging
Praveen Kumar
 
Samsung_EnodeLSMR__Integration_Module__V1.pdf (1).pdf
RaviSharma1113
 
LTE Core Network
BSP Media Group
 
Lte overview titus
Nabil Al_Mutawakel
 
20121129 lte basic procedures (2)
Debasish Sahoo
 
Ad

Recently uploaded (20)

PDF
Spectral efficient network and resource selection model in 5G networks
IAESIJAI
 
PPT
“AI and Expert System Decision Support & Business Intelligence Systems”
ZubinRadhakrishnan
 
PDF
Agricultural_Statistics_at_a_Glance_2022_0.pdf
SandeepSingh286037
 
PDF
TokAI - TikTok AI Agent : The First AI Application That Analyzes 10,000+ Vira...
SOFTTECHHUB
 
PPTX
KOM of Painting work and Equipment Insulation REV00 update 25-dec.pptx
muhammadmuneebnaeem7
 
PDF
Build a system with the filesystem maintained by OSTree @ COSCUP 2025
Jian-Hong Pan
 
PDF
Building Integrated photovoltaic BIPV_UPV.pdf
SandeepSingh286037
 
PPTX
VMware vSphere Foundation How to Sell Presentation-Ver1.4-2-14-2024.pptx
blackmambaettijean
 
PDF
The Rise and Fall of 3GPP – Time for a Sabbatical?
3G4G
 
PPTX
Digital-Transformation-Roadmap-for-Companies.pptx
David Malick Dieng
 
PDF
Empathic Computing: Creating Shared Understanding
Mark Billinghurst
 
PDF
Network Security Unit 5.pdf for BCA BBA.
Serpent6
 
PDF
Electronic commerce courselecture one. Pdf
OmerMohamed64
 
PDF
gpt5_lecture_notes_comprehensive_20250812015547.pdf
Chinchu40
 
PPTX
sap open course for s4hana steps from ECC to s4
sreeni2106invites
 
PDF
Reach Out and Touch Someone: Haptics and Empathic Computing
Mark Billinghurst
 
PDF
NewMind AI Weekly Chronicles - August'25-Week II
NewMind AI
 
PDF
A comparative analysis of optical character recognition models for extracting...
IAESIJAI
 
PDF
Machine learning based COVID-19 study performance prediction
IAESIJAI
 
DOCX
The AUB Centre for AI in Media Proposal.docx
GAONE9
 
Spectral efficient network and resource selection model in 5G networks
IAESIJAI
 
“AI and Expert System Decision Support & Business Intelligence Systems”
ZubinRadhakrishnan
 
Agricultural_Statistics_at_a_Glance_2022_0.pdf
SandeepSingh286037
 
TokAI - TikTok AI Agent : The First AI Application That Analyzes 10,000+ Vira...
SOFTTECHHUB
 
KOM of Painting work and Equipment Insulation REV00 update 25-dec.pptx
muhammadmuneebnaeem7
 
Build a system with the filesystem maintained by OSTree @ COSCUP 2025
Jian-Hong Pan
 
Building Integrated photovoltaic BIPV_UPV.pdf
SandeepSingh286037
 
VMware vSphere Foundation How to Sell Presentation-Ver1.4-2-14-2024.pptx
blackmambaettijean
 
The Rise and Fall of 3GPP – Time for a Sabbatical?
3G4G
 
Digital-Transformation-Roadmap-for-Companies.pptx
David Malick Dieng
 
Empathic Computing: Creating Shared Understanding
Mark Billinghurst
 
Network Security Unit 5.pdf for BCA BBA.
Serpent6
 
Electronic commerce courselecture one. Pdf
OmerMohamed64
 
gpt5_lecture_notes_comprehensive_20250812015547.pdf
Chinchu40
 
sap open course for s4hana steps from ECC to s4
sreeni2106invites
 
Reach Out and Touch Someone: Haptics and Empathic Computing
Mark Billinghurst
 
NewMind AI Weekly Chronicles - August'25-Week II
NewMind AI
 
A comparative analysis of optical character recognition models for extracting...
IAESIJAI
 
Machine learning based COVID-19 study performance prediction
IAESIJAI
 
The AUB Centre for AI in Media Proposal.docx
GAONE9
 

Call processing and handover.eng

  • 1. 1/73 Customer Training Center Jaeho, Lee Distribution EnglishED01
  • 4. 4/73 Protocol Stack UE Control Plane UE User Plane L1 MAC RLC PDCP RRC NAS L1 MAC RLC PDCP RRC L1 L2 IP SCTP S1-AP Relay L1 L2 IP SCTP S1-AP L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C L1 L2 IP UDP GTP-C NAS LTE-Uu S1-MME S11 S5/S8a UE eNB MME S-GW P-GW SGi L1 MAC RLC PDCP IP App L1 MAC RLC PDCP L1 L2 UDP/IP GTP-U Relay LTE-Uu S1-U S5/S8 L1 L2 UDP/IP GTP-U L1 L2 UDP/IP GTP-U Relay L1 MAC UDP/IP GTP-U IP UE eNB S-GW P-GW
  • 5. 5/73 eNB Software Architecture • CPS (Call Processing Software): LTE Control & Bearer Protocol processing • OAM (Operation and Maintenance): eNB Operation and Maintenance • MW (Middleware): IPC and Redundancy function • IPRS (IP Routing Software): Routing protocol operation • NP SW (Network Processor Software): Packet forwarding function • OS (Operating System): Embedded Linux • DD (Device Driver): initializing and setting the devices
  • 6. 6/73 Call Software Blocks (1/3) ECCB GTPB PDCB RLCB MACB Other eNB EPC PHY UE S1-c X2-c S1-u X2-u ECS (eNB Control Subsystem) EDS (eNB Data Subsystem) LTE eNB LEGEND : (UDP port)Control (IPC) Traffic SCTB ECMM ESCM ERCM ERRM ECCM EHCM Uu ECCB ECMB Interface
  • 7. 7/73 Call Software Blocks (2/3) ECMB (eNB Common Management Block) Initiate eNB and set the common channel Transmit system information for initiating UE Load Control for cell and system overload ECCB (eNB Call Control Block) Radio Resource Management, Call Admission Control RRC/S1-AP ASN.1 Interface, X2-AP ASN.1 Interface Control the basic call access, S1-AP Paging, Handover call control, Call Trace SCTB (Stream Control Transmission protocol Block) S1-C/X2-C SCTP Interface (Association setup/release), S1/X2 AP message Transmission
  • 8. 8/73 Call Software Blocks (3/3) GTPB (GPRS Tunneling Protocol Block) GPRS(General Packet Radio Service) Tunneling Protocol for data access on S1-U or X2-U. PDCB (Packet Data Convergence protocol Block) Header compression and decompression on IP packet stream, Ciphering, Integrity DL/UL data forwarding on Handover PDCP sequence number maintenance, Timer based PDCP SDU discard RLCB (Radio Link Control Block) Radio Link control and ARQ(Automatic Repeat Request) RLC SDU concatenation/segmentation/reassemble, In sequence delivery, RLC re- establishment RLC PDU re-segmentation, Paging MACB (Medium Access Control Block)
  • 9. 9/73 Main ID and S1/X2 Procedure
  • 11. 11/73 E-UTRAN Identifiers (2/3) UE-Related ID on S1 (for UE-associated signaling) UE-Related ID on X2 (for X2 Handover)
  • 13. 13/73 S1 Interface: Procedures (1/2) Class 1 Procedures Sender expects response from receiver
  • 14. 14/73 S1 Interface: Procedures (2/2) Class 2 Procedures Sender does not expect response
  • 15. 15/73 X2 Interface: Procedures Class 1 Procedures Class 2 Procedures
  • 17. 17/73 S1 Setup between eNB and MME Objective To setup the S1AP connection Exchange configuration information
  • 18. 18/73 X2 Setup between eNB and eNB Objective To setup the X2AP connection Exchange configuration information Neighbor PCI info is exchanged for supporting Automatic PCI Selection
  • 19. 19/73 Attach Procedure (1/2) UE Source eNB MME S-GW EPC 4. Initial UE Message(+ Attach Requet) NAS procedure( Nas security, Authentication ) 7. Initial Context Setup Request (+ Attach Accept) 2. RRC Connection Setup 1. RRC Connection Request 3. RRC Connection Setup Complete 5. Create Session Request 6. Create Session Response
  • 20. 20/73 Attach Procedure (2/2) UE Source eNB MME S-GW EPC 10. UE Capbility Info Indication 13. RRC Connection Reconfiguration 8. UE Capability Enquiry 9. UE Capability Information 12. Security Mode Complete 11. Security Mode Command 14. RRC Connection Reconfiguration Complete 15. Initial Context Setup Response 18. Modify Bearer Request 19. Modify Bearer Response 16. Uplink Information Transfer 17. Uplink NAS Transport Uplink Data
  • 21. 21/73 Detach Procedure(1/2) – w/o RRC Connection UE Source eNB MME S-GW EPC 4. Initial UE Message(+ Detach Requet) 9. UE Context Release Command 2. RRC Connection Setup 1. RRC Connection Request 3. RRC Connection Setup Complete (+ Detach Request) 6. Delete Session Response 7. Downlink NAS Transport (+ Detach Accept) 8. Downlink Information Transfer(+ Detach Accept) 10. RRC Connection Release 11. UE Context Release Complete 5. Delete Session Request
  • 22. 22/73 Detach Procedure (2/2) – w RRC Connection UE Source eNB MME S-GW EPC 2. Uplink NAS Transport(+ Detach Requet) 7. UE Context Release Command 1. Uplink Information Transfer (+ Detach Request) 4. Delete Session Response 5. Downlink NAS Transport (+ Detach Accept) 6. Downlink Information Transfer(+ Detach Accept) 8. RRC Connection Release 9. UE Context Release Complete 3. Delete Session Request
  • 23. 23/73 LTE Measurement Report Events Intra-LTE measurement events Event A1 - Serving becomes better than threshold. => release the measurement gap. Event A2 - Serving becomes worse than threshold. => setup measurement gap. Event A3 - Neighbour becomes offset better than serving. => trigger Intra-LTE handover => execute ANR Event A4 - Neighbour becomes better than threshold. Event A5 - Serving becomes worse than threshold1 and neighbour becomes better than threshold2. Inter-RAT measurement events Event B1 - Inter RAT neighbour becomes better than threshold. Event B2 - Serving becomes worse than threshold1 and inter RAT neighbour becomes better than threshold2. => trigger Inter-RAT handover
  • 24. 24/73 Measurement Signaling & Info MeasurementReport UE EUTRAN Measurement Reporting from the UE Measurement Report message has Physical Cell Id (PCI) info of neighbor cell. Execute handover using PCI of Measurement Report message received from eNB. In case of neighbor cell of CDMA2000, preRegistrationStatusHRPD information is included requested interworking- HRPD. Cell Global Id (CGI) information is included as requested from eNB. ANR function is executed using CGI information from UE on eNB.
  • 25. 25/73 Handover Classification Intra-RAT Handover Intra-eNB Handover Inter-eNB Handover over X2 Inter-eNB Handover over S1 (Intra-MME) Inter-eNB Handover over S1 (Inter-MME) Inter-RAT Handover CDMA2000, GERAN, UTRA, etc.
  • 28. 28/73 Handover Procedure [measurement] RSRP [dBm] : Reference Signal Received Power Absolute value, not related to Payload RSSI [dBm] : Received Signal Strength Indicator Received power of center 6RB (1.08MHz) Directly proportional to Payload RSRQ [dB] : RSRP/RSSI ratio Inversely proportional to Payload – Using for handover of cell loading frequency 0 RSSI [dBm] : 6RB power (6RB=72subcarrier=1.08MHz) BW = 10MHz RSRP [dBm] : carrier powerRS carrier data carrier
  • 30. 30/73 Intra-LTE / Inter-eNB X2 Handover UE Source eNB MME S-GW EPC 1. MeasurementReport Target eNB Downlink/Uplink data Downlink/Uplink data 3. HANDOVER REQUEST ACKNOWLEDGE 5. SN STATUS TRANSFER 4. RRCConnection- Reconfiguration (mobilityControlinfo) Data forwarding 6. Synchronization/UL allocation and timing advance 7. RRCConnectionReconfigurationComplete Forwarded data Uplink data Forwarded data Downlink data Down/Uplink data Down/Uplink data Uplink data Downlink data 8. PATH SWITCH REQUEST 9. Modify Bearer Request End marker End marker 10. Modify Bearer Response11. PATH SWITCH REQUEST ACKNOWLEDGE 12. UE CONTEXT RELEASE 2. HANDOVER REQUEST
  • 31. 31/73 Intra-LTE / Inter-eNB S1 Handover (1/2) UE Source eNB MME S-GW EPC Target eNB Downlink/Uplink data Downlink/Uplink data 3. HANDOVER REQUEST 5. Create Indirect Data Forwarding Tunnel Request 8. RRCConnection- Reconfiguration (mobilityControlinfo) 1) Direct data forwarding 1. Decision to trigger a relocation via S1 2. HANDOVER REQUIRED Indirect data forwarding 6. Create Indirect Data Forwarding Tunnel Response 7. HANDOVER COMMAND 9. eNB STATUS TRANSFER 10. MME STATUS TRANSFER 2) Indirect data fowarding 11. Detach from old cell/Synchronize to new cell 12. RRCConnectionReconfigurationComplete Forwarded data Uplink data Uplink data 4. HANDOVER REQUEST ACKNOWLEDGE
  • 32. 32/73 Intra-LTE / Inter-eNB S1 Handover (2/2) UE Source eNB MME S-GW EPC Target eNB Downlink data Downlink data End marker End marker 13. HANDOVER NOTIFY 14. Modify Bearer Request 15. Modify Bearer Response Forwarded data 16. Tracking Area Update procedure 17. UE CONTEXT RELEASE COMMAND 18. UE CONTEXT RELEASE COMPLETE 19. Delete Indirect Data Forwarding Tunnel Request 20. Delete Indirect Data Forwarding Tunnel Response Downlink/Uplink data Downlink/Uplink data
  • 34. 34/73 MME Configuration (1/2) CHG-MME-CONF : Setup information related MME Input the MME’s status connected S1 interface CLI Command
  • 35. 35/73 SRB RLC Configuration (1/2) CHG-SRB-QCI : Setup QoS information on SRB CLI Command
  • 36. 36/73 SRB RLC Configuration (2/2) CHG-SRB-RLC : Setup RLC information on SRB CLI Command The timer is for the prohibition of transmission of STATUS_STATUS on received-Entity(AM_RLC)
  • 37. 37/73 SRB MAC Configuration (1/4) CHG-LOCH-INF : Setup Logical channel information per QCI CLI Command
  • 38. 38/73 SRB MAC Configuration (2/4) CHG-TRCH-INF : Setup Transport channel information per Cell CLI Command Marking cell index for changing or displaying
  • 39. 39/73 SRB MAC Configuration (3/4) CHG-DRX-INF : Setup DRX information per Cell CLI Command
  • 40. 40/73 SRB MAC Configuration (4/4) CHG-DPHY-SPS Change parameters for the operating of Dedicated semiPersistScheduling. Cell_NUM : 0 ~ 5 PO_NOMINAL_PUSCHPERSISTENT: SPS Po parameter using power control is -126 ~ 24, default: -80 PO_UEPUSCHPERSISTENT: SPS Po parameter’s range on Power control per UE: - 8 ~7, default: 0 CHG-DPHY-PUSCH Change parameters for Dedicated PUSCH operaiton. Cell NUM: 0 ~ 5 BETA_OFFSET_ACKINDEX: Set the value of multiplexing ACK/NACK and PUSCH. Range: 0 ~ 15, default: 8 BETA_OFFSET_RIINDEX: Set the value of multiplexing RI and PUSCH Range: 0 ~ 15, default: 5 BETA_OFFSET_CQIINDEX: Set the value of multiplexing CQI and PUSCH Range: 0 ~ 15, default: 11
  • 41. 41/73 SRB MAC Configuration (4/4) CHG-ULPWR-CTRL Change parameters for the operating of Dedicated Uplink Power Control. Cell Number: 0 ~5 PO_UE_PUSCH: non-persistent scheduling Po parameter using PUSCH Power control per UE. Range: -8 ~ 7, default: 0 DELTA_MCSENABLED: Usage possibility for different MCS on Power offset Range: ci_en0/ci_en1/, default: ci_en0 ACCUMULATION_ENABLE: TPC Mode(accumulation mode/absolute mode) Range: 0 ~ 1, default: 1(accumulation mode) PO_UE_PUCCH: Po parameter(-8 ~ 7), default: 0 P_SRSOFFSET: This index is indicating the power offset of PUSCH and SRS: 0~15, default:7
  • 42. 42/73 SRB MAC Configuration (4/4) CHG-CQI-REPORTING Change parameters for the operating CQI Reporting TRANSMISSION_MODE: ci_tm1,2,3,4, ~ 8. default null – Mode 1: Single antenna port, port 0 – Mode 2: Transmit diversity – Mode 3: Large-delay CDD – Mode 4: Closed-loop spatial multiplexing – Mode 5: MU-MIMO – Mode 6: Closed-loop spatial multiplexing, single layer – Mode 7: Single antenna port, UE-specific RS (port 5) – Mode 8 (new in Rel-9): Single or dual-layer transmission with UE-Specific RS Port 7 and/or 8 Select CQI on Wideband/subband.
  • 43. 43/73 SRB MAC Configuration (4/4) CHG-DPHY-ULSRS Change the parameters for operating of Dedicated Uplink RS. Cell_NUM: 0 ~ 5 SRS_HOPPING_BANDWIDTH: Set the Area that is became “hopping status of Sounding RS. ci_hbw0 ~ hbw3, default: ci_hbw0 DURATION: Set the duration of sounding RS. If the value is ‘True’, the transmission of Sounding RS is not stopped until disabled. If the value is ‘False’ , transmit one time. (Range: 0 ~1), default vlalue: 1 CHG-DPHY-SR Change the parameters for operating of Dedicated Scheduling Request. Cell NUM: 0 ~5 DSR_TRANS_MAX: Set the maximum transmittable counts of scheduling requests until received PUSCH resource on UE.(ci_dsr_TransMax_n4 ~ 8,16,32,64) , default value: ci_dsr_TransMax_n64
  • 44. 44/73 DRB PDCP Configuration (1/3) CHG-PDCP-INF : Set the PDCP information per QCI CLI Command
  • 45. 45/73 DRB PDCP Configuration (2/3) CHG-ROHC-INF : Setup ROHC information per QCI CLI Command
  • 46. 46/73 DRB PDCP Configuration (3/3) CHG-SECU-INF : Set the Security Algorithm information CLI Command
  • 47. 47/73 DRB RLC Configuration CHG-RLC-INF : Set the RLC information per QCI CLI Command
  • 49. 49/73 Neighbor Configuration (1/7) The value is different for opeartors. Input PLMN Id of eNB operator. Input the value same as PLMN ID of eNB. Creation EUTRA Neighbor – PLD update or manually input with CLI on LSM CLI Command Create information of E-UTRA cells located near a base station
  • 50. 50/73 Neighbor Configuration (2/7) Parameter Description Range Value Cell Num Cell number of Base Station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP eNB ID Neighbor eNB Identity 20 or 28 BITS - Local Cell ID Neighbor local cell ID 0 ~ 255 - eNB Type Neighbor eNB type Macro or Home Macro eNB MCC Mobile Country Code of Neighbor eNB - Ex) Korea: 450 eNB MNC Mobile Network Code of Neighbor eNB - Physical Cell ID Neighbor cell PCI 0 ~ 503 - TAC Neighbor cell TAC 2 BYTES - PLMNs PLMN Lists supported neighbor cell - -
  • 51. 51/73 Neighbor Configuration (3/7) Parameter Description Range Value EARFCN UL Uplink EARFCN 0 ~ 65535 - EARFCN DL Downlink EARFCN 0 ~ 65535 - Bandwidth UL Uplink Bandwidth n6, n15, n25, n50, n75, n100 It’s different per operators. Bandwidth DL Downlink Bandwidth n6, n15, n25, n50, n75, n100 It’s different per operators. Individual Offset Cell Individual Offset adaptable neighbor cell. dB-24, dB-22, dB-20, dB-18, dB-16, dB-14, dB-12, dB-10, dB-8, dB-6, dB-4, dB-2, dB-1, dB0, dB1, dB2, dB3, dB4, dB5, dB6, dB8, dB10, dB12, dB14, dB16 dB18, dB20, dB22, dB24 dB0 Qoffset Cell Cell Quality Offset adaptable neighbor cell. Same dB0 Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
  • 52. 52/73 Neighbor Configuration (4/7) CDMA2000 1xRTT Neighbor creation – input remote neighbor widow or CLI CLI Command Create the information of CDMA2000 1xRTT Cells located near by a base station
  • 53. 53/73 Neighbor Configuration (5/7) Parameter Description Range Value Cell Num Cell number in base station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP SID CDMA2000 1xRTT SID 0 ~ 32767 - NID CDMA2000 1xRTT NID 0 ~ 65535 - Base ID CDMA2000 1xRTT Base ID 0 ~ 65535 - Band Class CDMA2000 1xRTT Band Class bc0, bc1, bc2, bc3, bc4, bc5, bc6, bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15, bc16, bc17 - ARFCN Neighbor cell’s ARFCN 0 ~ 2047 - PN Offset Neighbor cell’s PN Offset (CDMA2000’s PCI) 0 ~ 511 - Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
  • 54. 54/73 Neighbor Configuration (6/7) Creation CDMA2000 HRPD Neighbor – input remote neighbor widow or CLI CLI Command Create the information of CDMA2000 HRPD Cells located near by a base station
  • 55. 55/73 Neighbor Configuration (7/7) Parameter Description Range Value Cell Num Cell number in base station 0~5 - Relation Index Relation Index - - Status Neighbor status EQUIP or N_EQUIP N_EQUIP Color Code Neighbor Cell’s Color Code 0 ~ 255 - BSM ID Neighbor Cell’s BSM ID 0 ~ 63 - BSC ID Neighbor Cell’s BSC ID 0 ~ 1 - DPSS ID Neighbor Cell’s DPSS ID 0 ~ 7 - BTS ID Neighbor Cell’s BTS ID 0 ~ 2047 - Sector ID Neighbor Cell’s Sector ID 0 ~ 7 - Band Class Neighbor Cell’s Band Class bc0, bc1, bc2, bc3, bc4, bc5, bc6, bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15, bc16, bc17 - ARFCN Neighbor Cell’s ARFCN 0 ~ 2047 - PN Offset Neighbor Cell’s PN Offset (CDMA2000’s PCI) 0 ~ 511 - Is Remove Allowed Whether or not delete the neighbor cell TRUE or FALSE TRUE Is Handover Allowed Whether or not handover to neighbor cell TRUE of FALSE TRUE
  • 57. 57/73 Handover Event Configuration – Event A3 (1/3) Event A3 : Use for Intra LTE Handover and SON ANR - A3PurposeInraLteHandover - A3PurposeReportStrongestCells - Unit: dBm - Actual value: PLD value * 0.5 - RSRP or RSRQ - sameAsTriggerQuantity or both Change EUTRA A3 Criteria information CLI Command
  • 58. 58/73 Handover Event Configuration – Event A3 (2/3) Parameter Description Range Value Cell Num Cell number in base station 0~5 N/A Purpose The purpose of Event A3 usage 0: A3PurposeIntraLteHandov er 1: A3ReportStrongestCells 2: A3PurposeSpare_1 3: A3PurposeSpare_2 N/A Active State The status of Event A3 0: Inactive 1: Active Active A3 Offset RSRP threshold value using the condition of EUTRA measurement report triggering for Event A3 . (unit: dBm) -30 ~ 30 4 A3 Report On Leave Whether or not to report in case of Event A3 leaving condition TRUE or FALSE FALSE Hysteresis The entry/leave condition on Event triggered reporting. (unit: dB) 0 ~ 30 0
  • 59. 59/73 Handover Event Configuration – Event A3 (3/3) Parameter Description Range Value Time To Trigger The sufficient time in specific criteria when UE try to trigger the measurement report . (unit: ms) ms0, ms40, ms64, ms80, ms100, ms128, ms160, ms256, ms320, ms480, ms512, ms640, ms1024, ms1280, ms2560, ms5120 ms480 Trigger Quantity The quantity information used for evaluating the triggering condition for Events. RSRP or RSRQ RSRP Report Quantity The quantity information including Measurement Report Message. SamsAsTriggerQuantity or Both SameAsTriggerQuantity Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 8 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r8
  • 60. 60/73 Handover Event Configuration – Event B2 (1/4) Event B2 : Usage for Inter RAT(CDMA2000 1xRTT) Handover CLI Command Change CDMA2000 1xRTT B2 Criteria Information
  • 61. 61/73 Handover Event Configuration – Event B2 (2/4) Event B2 : Usage for Inter RAT(CDMA2000 HRPD) Handover CLI Command Change CDMA2000 HRPD B2 Criteria Information
  • 62. 62/73 Handover Event Configuration – Event B2 (3/4) Parameter Description Range Value Cell Num Cell number in base station 0~5 N/A Purpose The purpose of Event B2 Usage 0: B2PurposeInterRatHandover 1: B2PurposeSpare_1 3: B2PurposeSpare_2 N/A Active State The status of Event B2 0: Inactive 1: Active Active B2 Threshold1 (RSRP) RSRP threshold value using the condition of EUTRA measurement report triggering for Event B2 . 0 ~ 97 70 B2 Threshold1 (RSRQ) RSRP threshold value using the condition of EUTRA measurement report triggering for Event B2. 0 ~ 34 10 B2 Threshold2 CDMA 2000 The threshold value using the condition of CDMA2000 HRPD measurement report triggering for Event B2. 0 ~ 63 20 Hysteresis The entry/leave condition on Event triggered reporting. (unit: dB) 0 ~ 30 0
  • 63. 63/73 Handover Event Configuration – Event B2 (4/4) Parameter Description Range Value Time To Trigger The sufficient time in specific criteria when UE try to trigger the measurement report. (unit: ms) ms0, ms40, ms64, ms80, ms100, ms128, ms160, ms256, ms320, ms480, ms512, ms640, ms1024, ms1280, ms2560, ms5120 ms80 Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 1 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r1 Trigger Quantity EUTRA The quantity information used for evaluating the condition of EUTRA event triggering. RSRP or RSRQ RSRP
  • 64. 64/73 Periodic Report Configuration – Periodic (1/4) Periodic Report : Usage for ICIC, SON ANR. CLI Command Change EUTRA Periodic Criteria Information
  • 65. 65/73 Periodic Report Configuration – Periodic (2/4) Periodic Report : Usage for interworking CDMA2000 1xRTT in the future. Change CDMA2000 1xRTT Periodic Criteria Information CLI Command
  • 66. 66/73 Periodic Report Configuration – Periodic (3/4) Periodic Report: Usage for interworking CDMA2000 HRPD in the future. CLI Command Change CDMA2000 HRPD Periodic Criteria Information
  • 67. 67/73 Periodic Report Configuration – Periodic (4/4) Parameter Description Range Value Purpose The purpose of configuration on Periodic measurement reporting. PeriodicalPurposeReportStrongestCells PeriodicalPurposeReportStrongestCellsForSON PeriodicalPurposeReportCGI N/A Active State The operation status of Periodic report. 0: Inactive 1: Active Inactive Trigger Quantity (EUTRA Only) The quantity information for evaluating the triggering condition for event. RSRP or RSRQ RSRP Report Quantity (EUTRA Only) The quantity information including Measurement report message. SamsAsTriggerQuantity or Both SameAsTrigg erQuantity Max Report Cell The maximum number of cell including Measurement report on UE. 1 ~ 8 1 Report Interval The interval information between Periodical reports. (unit: ms) ms120, ms240, ms480, ms640, ms1024, ms2048, ms5120, ms10240, min1, min6, min12, min30, min60, ms240 Report Amount The number of messages on Measurement report. r1, r2, r4, r8, r16, r32, r64, infinity r1
  • 68. 68/73 Handover Related Timers (1/2) X2, S1 Protocol Timers TX2RELOCprep, TX2RELOCoverall, TS1RELOCprep, TS1RELOCoverall CLI Command Change timer operation Information
  • 69. 69/73 Handover Related Timers (2/2) Parameter Description Range Value S1_PATH_SWITCH Target eNB sends Path Switch Request message to MME for S1 handover. The timer should be set when Target eNB is waiting Path Switch Request Acknowledge message from MME. 0 ~ 65535 (ms) 3000 S1 HANDOVER PREPARATION Source eNB sends Handover Request message to target eNB for S1 handover. The timer should be set when Source eNB is waiting Handover Request Acknowledge message from Target eNB. 0 ~ 65535 (ms) 5000 S1 RELOC OVERALL After the preparation procedure for S1 Handover, the timer should be set when Source eNB is waiting UE Context Release Command message from MME. 0 ~ 65535 (ms) 5000 S1 HANDOVER CANCEL Source eNB sends Handover Cancel message to MME for S1 handover. The timer should be set when Source eNB is waiting Handover Cancel Acknowledge message from MME. 0 ~ 65535 (ms) 5000 X2 HANDOVER PREPARATION Source eNB sends Handover Request message to target eNB for X2 handover. The timer should be set when Source eNB is waiting Handover Request Acknowledge message from Target eNB. 0 ~ 65535 (ms) 5000 X2 RELOC OVERALL After the preparation procedure for X2 Handover, the timer should be set when Source eNB is waiting UE Context Release message from target eNB. 0 ~ 65535 (ms) 5000 X2 STORE UE CONTEXT After X2 Handover, the MRO timer is working on target eNB. If target eNB receives RLF indication message while this timer is working on Target eNB, MRO statistic function is executed. 0 ~ 65535 (ms) 10000
  • 71. 71/73 eNB-controlled Handover Restriction (1/2) NO_HO If this option parameter is set to ‘TRUE’, It is not handover to the designated eNB. Set IP version 6 format for specific neighbor eNB IP address. CLI Command
  • 72. 72/73 eNB-controlled Handover Restriction (2/2) IS_HOALLOWED If this option parameter is set to ‘FALSE’, It is not handover to the designated cell. CLI Command Change E-UTRA cell’s information which is located at surrounding base station.
  • 73. 73/73