Capítulo 09 solda

Chapter 9
9-1 Eq. (9-3):
F = 0.707hlτ = 0.707(5/16)(4)(20) = 17.7 kip Ans.
9-2 Table 9-6: τall = 21.0 kpsi
f = 14.85h kip/in
= 14.85(5/16) = 4.64 kip/in
F = f l = 4.64(4) = 18.56 kip Ans.
9-3 Table A-20:
1018 HR: Sut = 58 kpsi, Sy = 32 kpsi
1018 CR: Sut = 64 kpsi, Sy = 54 kpsi
Cold-rolled properties degrade to hot-rolled properties in the neighborhood of the weld.
Table 9-4:
τall = min(0.30Sut, 0.40Sy)
= min[0.30(58), 0.40(32)]
= min(17.4, 12.8) = 12.8 kpsi
for both materials.
Eq. (9-3): F = 0.707hlτall
F = 0.707(5/16)(4)(12.8) = 11.3 kip Ans.
9-4 Eq. (9-3)
τ =
√
2F
hl
=
√
2(32)
(5/16)(4)(2)
= 18.1 kpsi Ans.
9-5 b = d = 2 in
(a) Primary shear Table 9-1
τy =
V
A
=
F
1.414(5/16)(2)
= 1.13F kpsi
F
7"
1.414
shi20396_ch09.qxd 8/19/03 9:30 AM Page 246

Chapter 9 247
Secondary shear Table 9-1
Ju =
d(3b2 + d2)
6
=
2[(3)(22) + 22]
6
= 5.333 in3
J = 0.707hJu = 0.707(5/16)(5.333) = 1.18 in4
τx = τy =
Mry
J
=
7F(1)
1.18
= 5.93F kpsi
Maximum shear
τmax = τ 2
x + (τy + τy )2
= F 5.932 + (1.13 + 5.93)2 = 9.22F kpsi
F =
τall
9.22
=
20
9.22
= 2.17 kip Ans. (1)
(b) For E7010 from Table 9-6, τall = 21 kpsi
Table A-20:
HR 1020 Bar: Sut = 55 kpsi, Sy = 30 kpsi
HR 1015 Support: Sut = 50 kpsi, Sy = 27.5 kpsi
Table 9-5, E7010 Electrode: Sut = 70 kpsi, Sy = 57 kpsi
Therefore, the bar controls the design.
Table 9-4:
τall = min[0.30(50), 0.40(27.5)] = min[15, 11] = 11 kpsi
The allowable load from Eq. (1) is
F =
τall
9.22
=
11
9.22
= 1.19 kip Ans.
9-6 b = d = 2 in
Primary shear
τy =
V
A
=
F
4(0.707)(5/16)(2)
= 0.566F
Secondary shear
Table 9-1: Ju =
(b + d)3
6
=
(2 + 2)3
6
= 10.67 in3
J = 0.707hJu = 0.707(5/16)(10.67) = 2.36 in4
τx = τy =
Mry
J
=
(7F)(1)
2.36
= 2.97F
F
7"
shi20396_ch09.qxd 8/19/03 9:30 AM Page 247

248 Solutions Manual • Instructor’s Solution Manual to Accompany Mechanical Engineering Design
Maximum shear
τmax = τ 2
x + (τy + τy )2 = F 2.972 + (0.556 + 2.97)2 = 4.61F kpsi
F =
τall
4.61
Ans.
which is twice τmax/9.22 of Prob. 9-5.
9-7 Weldment, subjected to alternating fatigue, has throat area of
A = 0.707(6)(60 + 50 + 60) = 721 mm2
Members’endurance limit: AISI 1010 steel
Sut = 320 MPa, Se = 0.504(320) = 161.3 MPa
ka = 272(320)−0.995
= 0.875
kb = 1 (direct shear)
kc = 0.59 (shear)
kd = 1
kf =
1
Kf s
=
1
2.7
= 0.370
Sse = 0.875(1)(0.59)(0.37)(161.3) = 30.81 MPa
Electrode’s endurance: 6010
Sut = 62(6.89) = 427 MPa
Se = 0.504(427) = 215 MPa
ka = 272(427)−0.995
= 0.657
kb = 1 (direct shear)
kc = 0.59 (shear)
kd = 1
kf = 1/Kf s = 1/2.7 = 0.370
Sse = 0.657(1)(0.59)(0.37)(215) = 30.84 MPa
.
= 30.81
Thus, the members and the electrode are of equal strength. For a factor of safety of 1,
Fa = τa A = 30.8(721)(10−3
) = 22.2 kN Ans.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 248

Chapter 9 249
9-8 Primary shear τ = 0 (why?)
Secondary shear
Table 9-1: Ju = 2πr3
= 2π(4)3
= 402 cm3
J = 0.707hJu = 0.707(0.5)(402) = 142 cm4
M = 200F N · m (F in kN)
τ =
Mr
2J
=
(200F)(4)
2(142)
= 2.82F (2 welds)
F =
τall
τ
=
140
2.82
= 49.2 kN Ans.
9-9 Rank
fom =
Ju
lh
=
a3
/12
ah
=
a2
12h
= 0.0833
a2
h
5
fom =
a(3a2
+ a2
)
6(2a)h
=
a2
3h
= 0.3333
a2
h
1
fom =
(2a)4
− 6a2
a2
12(a + a)2ah
=
5a2
24h
= 0.2083
a2
h
4
fom =
1
3ah
8a3
+ 6a3
+ a3
12
−
a4
2a + a
=
11
36
a2
h
= 0.3056
a2
h
2
fom =
(2a)3
6h
1
4a
=
8a3
24ah
=
a2
3h
= 0.3333
a2
h
1
fom =
2π(a/2)3
πah
=
a3
4ah
=
a2
4h
= 0.25
a2
h
3
These rankings apply to ﬁllet weld patterns in torsion that have a square area a × a in
which to place weld metal. The object is to place as much metal as possible to the border.
If your area is rectangular, your goal is the same but the rankings may change.
Students will be surprised that the circular weld bead does not rank ﬁrst.
9-10
fom =
Iu
lh
=
1
a
a3
12
1
h
=
1
12
a2
h
= 0.0833
a2
h
5
fom =
Iu
lh
=
1
2ah
a3
6
= 0.0833
a2
h
5
fom =
Iu
lh
=
1
2ah
a2
2
=
1
4
a2
h
= 0.25
a2
h
1
shi20396_ch09.qxd 8/19/03 9:30 AM Page 249

fom =
Iu
lh
=
1
[2(2a)]h
a2
6
(3a + a) =
1
6
a2
h
= 0.1667
a2
h
2
¯x =
b
2
=
a
2
, ¯y =
d2
b + 2d
=
a2
3a
=
a
3
Iu =
2d3
3
− 2d2 a
3
+ (b + 2d)
a2
9
=
2a3
3
−
2a3
3
+ 3a
a2
9
=
a3
3
fom =
Iu
lh
=
a3
/3
3ah
=
1
9
a2
h
= 0.1111
a2
h
4
Iu = πr3
=
πa3
8
fom =
Iu
lh
=
πa3
/8
πah
=
a2
8h
= 0.125
a2
h
3
The CEE-section pattern was not ranked because the deflection of the beam is out-of-plane.
If you have a square area in which to place a fillet weldment pattern under bending, your
objective is to place as much material as possible away from the x-axis. If your area is rec-
tangular, your goal is the same, but the rankings may change.
9-11 Materials:
Attachment (1018 HR) Sy = 32 kpsi, Sut = 58 kpsi
Member (A36) Sy = 36 kpsi, Sut ranges from 58 to 80 kpsi, use 58.
The member and attachment are weak compared to the E60XX electrode.
Decision Specify E6010 electrode
Controlling property: τall = min[0.3(58), 0.4(32)] = min(16.6, 12.8) = 12.8 kpsi
For a static load the parallel and transverse fillets are the same. If n is the number of beads,
τ =
F
n(0.707)hl
= τall
nh =
F
0.707lτall
=
25
0.707(3)(12.8)
= 0.921
Make a table.
Number of beads Leg size
n h
1 0.921
2 0.460 →1/2"
3 0.307 →5/16"
4 0.230 →1/4"
Decision: Specify 1/4" leg size
Decision: Weld all-around
shi20396_ch09.qxd 8/19/03 9:30 AM Page 250

Chapter 9 251
Weldment Specifications:
Pattern: All-around square
Electrode: E6010
Type: Two parallel fillets Ans.
Two transverse fillets
Length of bead: 12 in
Leg: 1/4 in
For a figure of merit of, in terms of weldbead volume, is this design optimal?
9-12 Decision: Choose a parallel fillet weldment pattern. By so-doing, we’ve chosen an optimal
pattern (see Prob. 9-9) and have thus reduced a synthesis problem to an analysis problem:
Table 9-1: A = 1.414hd = 1.414(h)(3) = 4.24h in3
Primary shear
τy =
V
A
=
3000
4.24h
=
707
h
Secondary shear
Table 9-1: Ju =
d(3b2
+ d2
)
6
=
3[3(32
) + 32
]
6
= 18 in3
J = 0.707(h)(18) = 12.7h in4
τx =
Mry
J
=
3000(7.5)(1.5)
12.7h
=
2657
h
= τy
τmax = τ 2
x + (τy + τy )2 =
1
h
26572 + (707 + 2657)2 =
4287
h
Attachment (1018 HR): Sy = 32 kpsi, Sut = 58 kpsi
Member (A36): Sy = 36 kpsi
The attachment is weaker
Decision: Use E60XX electrode
τall = min[0.3(58), 0.4(32)] = 12.8 kpsi
τmax = τall =
4287
h
= 12 800 psi
h =
4287
12 800
= 0.335 in
Decision: Specify 3/8" leg size
Pattern: Parallel fillet welds
Electrode: E6010
Type: Fillet Ans.
Leg size: 3/8 in
shi20396_ch09.qxd 8/19/03 9:30 AM Page 251

9-13 An optimal square space (3" × 3") weldment pattern is ԽԽ or or ᮀ. In Prob. 9-12, there
was roundup of leg size to3/8 in. Consider the member material to be structural A36 steel.
Decision: Use a parallel horizontal weld bead pattern for welding optimization and
convenience.
Materials:
Member (A36): Sy = 36 kpsi, Sut 58–80 kpsi; use 58 kpsi
From Table 9-4 AISC welding code,
τall = min[0.3(58), 0.4(32)] = min(16.6, 12.8) = 12.8 kpsi
Select a stronger electrode material from Table 9-3.
Decision: Specify E6010
Throat area and other properties:
A = 1.414hd = 1.414(h)(3) = 4.24h in2
¯x = b/2 = 3/2 = 1.5 in
¯y = d/2 = 3/2 = 1.5 in
Ju =
d(3b2
+ d2
)
6
=
3[3(32
) + 32
]
6
= 18 in3
J = 0.707hJu = 0.707(h)(18) = 12.73h in4
Primary shear:
τx =
V
A
=
3000
4.24h
=
707.5
h
Secondary shear:
τ =
Mr
J
τx = τ cos 45◦
=
Mr
J
cos 45◦
=
Mrx
J
τx =
3000(6 + 1.5)(1.5)
12.73h
=
2651
h
τy = τx =
2651
h
ry
x
rx
r ␶ЈЈ
␶ЈЈ
␶Ј
y
x
x
␶ЈЈy
shi20396_ch09.qxd 8/19/03 9:30 AM Page 252

Chapter 9 253
τmax = (τx + τx)2 + τ 2
y
=
1
h
(2651 + 707.5)2 + 26512
=
4279
h
psi
Relate stress and strength:
τmax = τall
4279
h
= 12 800
h =
4279
12 800
= 0.334 in → 3/8 in
Pattern: Horizontal parallel weld tracks
Electrode: E6010
Type of weld: Two parallel ﬁllet welds
Leg size: 3/8 in
Additional thoughts:
Since the round-up in leg size was substantial, why not investigate a backward C weld
pattern. One might then expect shorter horizontal weld beads which will have the advan-
tage of allowing a shorter member (assuming the member has not yet been designed). This
will show the inter-relationship between attachment design and supporting members.
9-14 Materials:
Member (A36): Sy = 36 kpsi, Sut = 58 to 80 kpsi; use Sut = 58 kpsi
τall = min[0.3(58), 0.4(32)] = 12.8 kpsi
Decision: Use E6010 electrode. From Table 9-3: Sy = 50 kpsi, Sut = 62 kpsi,
τall = min[0.3(62), 0.4(50)] = 20 kpsi
Decision: Since A36 and 1018 HR are weld metals to an unknown extent, use
τall = 12.8 kpsi
Decision: Usethemostefﬁcientweldpattern–square,weld-all-around.Choose6" × 6" size.
Attachment length:
l1 = 6 + a = 6 + 6.25 = 12.25 in
Throat area and other properties:
A = 1.414h(b + d) = 1.414(h)(6 + 6) = 17.0h
¯x =
b
2
=
6
2
= 3 in, ¯y =
d
2
=
6
2
= 3 in
shi20396_ch09.qxd 8/19/03 9:30 AM Page 253

Primary shear
τy =
V
A
=
F
A
=
20 000
17h
=
1176
h
psi
Secondary shear
Ju =
(b + d)3
6
=
(6 + 6)3
6
= 288 in3
J = 0.707h(288) = 203.6h in4
τx = τy =
Mry
J
=
20 000(6.25 + 3)(3)
203.6h
=
2726
h
psi
τmax = τ 2
x + (τy + τy)2 =
1
h
27262 + (2726 + 1176)2 =
4760
h
psi
Relate stress to strength
τmax = τall
4760
h
= 12 800
h =
4760
12 800
= 0.372 in
Decision:
Specify 3/8 in leg size
Speciﬁcations:
Pattern: All-around square weld bead track
Electrode: E6010
Type of weld: Fillet
Weld bead length: 24 in
Leg size: 3/8 in
Attachment length: 12.25 in
9-15 This is a good analysis task to test the students’ understanding
(1) Solicit information related to a priori decisions.
(2) Solicit design variables b and d.
(3) Find h and round and output all parameters on a single screen. Allow return to Step 1
or Step 2
(4) When the iteration is complete, the ﬁnal display can be the bulk of your adequacy
assessment.
Such a program can teach too.
9-16 The objective of this design task is to have the students teach themselves that the weld
patterns of Table 9-3 can be added or subtracted to obtain the properties of a comtem-
plated weld pattern. The instructor can control the level of complication. I have left the
shi20396_ch09.qxd 8/19/03 9:30 AM Page 254

Chapter 9 255
presentation of the drawing to you. Here is one possibility. Study the problem’s opportuni-
ties, then present this (or your sketch) with the problem assignment.
Use b1 as the design variable. Express properties as a function of b1 . From Table 9-3,
category 3:
A = 1.414h(b − b1)
¯x = b/2, ¯y = d/2
Iu =
bd2
2
−
b1d2
2
=
(b − b1)d2
2
I = 0.707hIu
τ =
V
A
=
F
1.414h(b − b1)
τ =
Mc
I
=
Fa(d/2)
0.707hIu
τmax = τ 2 + τ 2
Parametric study
Let a = 10 in, b = 8 in, d = 8 in, b1 = 2 in, τall = 12.8 kpsi, l = 2(8 − 2) = 12 in
A = 1.414h(8 − 2) = 8.48h in2
Iu = (8 − 2)(82
/2) = 192 in3
I = 0.707(h)(192) = 135.7h in4
τ =
10 000
8.48h
=
1179
h
psi
τ =
10 000(10)(8/2)
135.7h
=
2948
h
psi
τmax =
1
h
11792 + 29482 =
3175
h
= 12 800
from which h = 0.248 in. Do not round off the leg size – something to learn.
fom =
Iu
hl
=
192
0.248(12)
= 64.5
A = 8.48(0.248) = 2.10 in2
I = 135.7(0.248) = 33.65 in4
Section AA
A36
Body welds
not shown
8"
8"
1
2
"
a
A
A
10000 lbf
1018 HR
Attachment weld
pattern considered
b
b1
d
shi20396_ch09.qxd 8/19/03 9:30 AM Page 255

vol =
h2
2
l =
0.2482
2
12 = 0.369 in3
I
vol
=
33.65
0.369
= 91.2 = eff
τ =
1179
0.248
= 4754 psi
τ =
2948
0.248
= 11 887 psi
τmax =
4127
0.248
.
= 12 800 psi
Now consider the case of uninterrupted welds,
b1 = 0
A = 1.414(h)(8 − 0) = 11.31h
Iu = (8 − 0)(82
/2) = 256 in3
I = 0.707(256)h = 181h in4
τ =
10 000
11.31h
=
884
h
τ =
10 000(10)(8/2)
181h
=
2210
h
τmax =
1
h
8842 + 22102 =
2380
h
= τall
h =
τmax
τall
=
2380
12 800
= 0.186 in
Do not round off h.
A = 11.31(0.186) = 2.10 in2
I = 181(0.186) = 33.67
τ =
884
0.186
= 4753 psi, vol =
0.1862
2
16 = 0.277 in3
τ =
2210
0.186
= 11 882 psi
fom =
Iu
hl
=
256
0.186(16)
= 86.0
eff =
I
(h2/2)l
=
33.67
(0.1862/2)16
= 121.7
Conclusions: To meet allowable stress limitations, I and A do not change, nor do τ and σ. To
meet the shortened bead length, h is increased proportionately. However, volume of bead laid
down increases as h2
. The uninterrupted bead is superior. In this example, we did not round h
and as a result we learned something. Our measures of merit are also sensitive to rounding.
When the design decision is made, rounding to the next larger standard weld ﬁllet size will
decrease the merit.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 256

Chapter 9 257
Had the weld bead gone around the corners, the situation would change. Here is a fol-
lowup task analyzing an alternative weld pattern.
9-17 From Table 9-2
For the box A = 1.414h(b + d)
Subtracting b1 from b and d1 from d
A = 1.414 h(b − b1 + d − d1)
Iu =
d2
6
(3b + d) −
d3
1
6
−
b1d2
2
=
1
2
(b − b1)d2
+
1
6
d3
− d3
1
length of bead l = 2(b − b1 + d − d1)
fom = Iu/hl
9-18 Below is a Fortran interactive program listing which, if imitated in any computer language
of convenience, will reduce to drudgery. Furthermore, the program allows synthesis by in-
teraction or learning without fatigue.
C Weld2.f for rect. fillet beads resisting bending C. Mischke Oct 98
1 print*,’weld2.f rectangular fillet weld-beads in bending,’
print*,’gaps allowed - C. Mischke Oct. 98’
print*,’ ’
print*,’Enter largest permissible shear stress tauall’
read*,tauall
print*,’Enter force F and clearance a’
read*,F,a
2 print*,’Enter width b and depth d of rectangular pattern’
read*,b,d
xbar=b/2.
ybar=d/2.
3 print*,’Enter width of gap b1, and depth of gap d1’
print*,’both gaps central in their respective sides’
read*,b1,d1
xIu=(b-b1)*d**2/2.+(d**3-d1**3)/6.
xl=2.*(d-d1)+2.*(b-b1)
b
b1
dd1
shi20396_ch09.qxd 8/19/03 9:30 AM Page 257

C Following calculations based on unit leg h = 1
AA=1.414*(b-b1+d-d1)
xI=0.707*xIu
tau2=F*a*d/2./xI
tau1=F/AA
taumax=sqrt(tau2**2+tau1**2)
h=taumax/tauall
C Adjust parameters for now-known h
AA=AA*h
xI=xI*h
tau2=tau2/h
tau1=tau1/h
taumax=taumax/h
fom=xIu/h/xl
print*,’F=’,F,’ a=’,a,’ bead length = ’,xl
print*,’b=’,b,’ b1=’,b1,’ d=’,d,’ d1=’,d1
print*,’xbar=’,xbar,’ ybar=’,ybar,’ Iu=’,xIu
print*,’I=’,xI,’ tau2=’,tau2,’ tau1=’,tau1
print*,’taumax=’,taumax,’ h=’,h,’ A=’,AA
print*,’fom=’,fom, ’I/(weld volume)=’,2.*xI/h**2/xl
print*,’ ’
print*,’To change b1,d1: 1; b,d: 2; New: 3; Quit: 4’
read*,index
go to (3,2,1,4), index
4 call exit
end
9-19 τall = 12 800 psi. Use Fig. 9-17(a) for general geometry, but employ beads and then ԽԽ
beads.
Horizontal parallel weld bead pattern
b = 6 in
d = 8 in
From Table 9-2, category 3
A = 1.414 hb = 1.414(h)(6) = 8.48 h in2
¯x = b/2 = 6/2 = 3 in, ¯y = d/2 = 8/2 = 4 in
Iu =
bd2
2
=
6(8)2
2
= 192 in3
I = 0.707hIu = 0.707(h)(192) = 135.7h in4
τ =
10 000
8.48h
=
1179
h
psi
6"
8"
shi20396_ch09.qxd 8/19/03 9:30 AM Page 258

Chapter 9 259
τ =
Mc
I
=
10 000(10)(8/2)
135.7h
=
2948
h
psi
τmax = τ 2 + τ 2 =
1
h
(11792
+ 29482
)1/2
=
3175
h
psi
Equate the maximum and allowable shear stresses.
τmax = τall =
3175
h
= 12 800
from which h = 0.248 in. It follows that
I = 135.7(0.248) = 33.65 in4
The volume of the weld metal is
vol =
h2
l
2
=
0.2482
(6 + 6)
2
= 0.369 in3
The effectiveness, (eff)H , is
(eff)H =
I
vol
=
33.65
0.369
= 91.2 in
(fom )H =
Iu
hl
=
192
0.248(6 + 6)
= 64.5 in
Vertical parallel weld beads
b = 6 in
d = 8 in
From Table 9-2, category 2
A = 1.414hd = 1.414(h)(8) = 11.31h in2
¯x = b/2 = 6/2 = 3 in, ¯y = d/2 = 8/2 = 4 in
Iu =
d3
6
=
83
6
= 85.33 in3
I = 0.707hIu = 0.707(h)(85.33) = 60.3h
τ =
10 000
11.31h
=
884
h
psi
τ =
Mc
I
=
10 000(10)(8/2)
60.3 h
=
6633
h
psi
τmax = τ 2 + τ 2 =
1
h
(8842
+ 66332
)1/2
=
6692
h
psi
8"
6"
shi20396_ch09.qxd 8/19/03 9:30 AM Page 259

Equating τmax to τall gives h = 0.523 in. It follows that
I = 60.3(0.523) = 31.5 in4
vol =
h2
l
2
=
0.5232
2
(8 + 8) = 2.19 in3
(eff)V =
I
vol
=
31.6
2.19
= 14.4 in
(fom )V =
Iu
hl
=
85.33
0.523(8 + 8)
= 10.2 in
The ratio of (eff)V/(eff)H is 14.4/91.2 = 0.158. The ratio (fom )V/(fom )H is
10.2/64.5 = 0.158. This is not surprising since
eff =
I
vol
=
I
(h2/2)l
=
0.707 hIu
(h2/2)l
= 1.414
Iu
hl
= 1.414 fom
The ratios (eff)V/(eff)H and (fom )V/(fom )H give the same information.
9-20 Because the loading is pure torsion, there is no primary shear. From Table 9-1, category 6:
Ju = 2πr3
= 2π(1)3
= 6.28 in3
J = 0.707 hJu = 0.707(0.25)(6.28)
= 1.11 in4
τ =
Tr
J
=
20(1)
1.11
= 18.0 kpsi Ans.
9-21 h = 0.375 in, d = 8 in, b = 1 in
From Table 9-2, category 2:
A = 1.414(0.375)(8) = 4.24 in2
Iu =
d3
6
=
83
6
= 85.3 in3
I = 0.707hIu = 0.707(0.375)(85.3) = 22.6 in4
τ =
F
A
=
5
4.24
= 1.18 kpsi
M = 5(6) = 30 kip · in
c = (1 + 8 + 1 − 2)/2 = 4 in
τ =
Mc
I
=
30(4)
22.6
= 5.31 kpsi
τmax = τ 2 + τ 2 = 1.182 + 5.312
= 5.44 kpsi Ans.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 260

Chapter 9 261
9-22 h = 0.6 cm, b = 6 cm, d = 12 cm.
Table 9-3, category 5:
A = 0.707h(b + 2d)
= 0.707(0.6)[6 + 2(12)] = 12.7 cm2
¯y =
d2
b + 2d
=
122
6 + 2(12)
= 4.8 cm
Iu =
2d3
3
− 2d2
¯y + (b + 2d) ¯y2
=
2(12)3
3
− 2(122
)(4.8) + [6 + 2(12)]4.82
= 461 cm3
I = 0.707hIu = 0.707(0.6)(461) = 196 cm4
τ =
F
A
=
7.5(103)
12.7(102)
= 5.91 MPa
M = 7.5(120) = 900 N · m
cA = 7.2 cm, cB = 4.8 cm
The critical location is at A.
τA =
McA
I
=
900(7.2)
196
= 33.1 MPa
τmax = τ 2 + τ 2 = (5.912
+ 33.12
)1/2
= 33.6 MPa
n =
τall
τmax
=
120
33.6
= 3.57 Ans.
9-23 The largest possible weld size is 1/16 in. This is a small weld and thus difﬁcult to accom-
plish. The bracket’s load-carrying capability is not known. There are geometry problems
associated with sheet metal folding, load-placement and location of the center of twist.
This is not available to us. We will identify the strongest possible weldment.
Use a rectangular, weld-all-around pattern – Table 9-2, category 6:
A = 1.414 h(b + d)
= 1.414(1/16)(1 + 7.5)
= 0.751 in2
¯x = b/2 = 0.5 in
¯y =
d
2
=
7.5
2
= 3.75 in
6
4.8
7.2
A
B
G
1"
7.5"
shi20396_ch09.qxd 8/19/03 9:30 AM Page 261

Iu =
d2
6
(3b + d) =
7.52
6
[3(1) + 7.5] = 98.4 in3
I = 0.707hIu = 0.707(1/16)(98.4) = 4.35 in4
M = (3.75 + 0.5)W = 4.25W
τ =
V
A
=
W
0.751
= 1.332W
τ =
Mc
I
=
4.25W(7.5/2)
4.35
= 3.664W
τmax = τ 2 + τ 2 = W 1.3322 + 3.6642 = 3.90W
Material properties: The allowable stress given is low. Let’s demonstrate that.
For the A36 structural steel member, Sy = 36 kpsi and Sut = 58 kpsi. For the 1020 CD
attachment, use HR properties of Sy = 30 kpsi and Sut = 55. The E6010 electrode has
strengths of Sy = 50 and Sut = 62 kpsi.
Allowable stresses:
A36: τall = min[0.3(58), 0.4(36)]
= min(17.4, 14.4) = 14.4 kpsi
1020: τall = min[0.3(55), 0.4(30)]
τall = min(16.5, 12) = 12 kpsi
E6010: τall = min[0.3(62), 0.4(50)]
= min(18.6, 20) = 18.6 kpsi
Since Table 9-6 gives 18.0 kpsi as the allowable shear stress, use this lower value.
Therefore, the allowable shear stress is
τall = min(14.4, 12, 18.0) = 12 kpsi
However, the allowable stress in the problem statement is 0.9 kpsi which is low from the
weldment perspective. The load associated with this strength is
τmax = τall = 3.90W = 900
W =
900
3.90
= 231 lbf
If the welding can be accomplished (1/16 leg size is a small weld), the weld strength is
12 000 psi and the load W = 3047 lbf. Can the bracket carry such a load?
There are geometry problems associated with sheet metal folding. Load placement is
important and the center of twist has not been identiﬁed. Also, the load-carrying capability
of the top bend is unknown.
These uncertainties may require the use of a different weld pattern. Our solution pro-
vides the best weldment and thus insight for comparing a welded joint to one which em-
ploys screw fasteners.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 262

Chapter 9 263
9-24
F = 100 lbf, τall = 3 kpsi
FB = 100(16/3) = 533.3 lbf
Fx
B = −533.3 cos 60◦
= −266.7 lbf
F
y
B = −533.3 cos 30◦
= −462 lbf
It follows that R
y
A = 562 lbf and Rx
A = 266.7 lbf, RA = 622 lbf
M = 100(16) = 1600 lbf · in
The OD of the tubes is 1 in. From Table 9-1, category 6:
A = 1.414(πhr)(2)
= 2(1.414)(πh)(1/2) = 4.44h in2
Ju = 2πr3
= 2π(1/2)3
= 0.785 in3
J = 2(0.707)hJu = 1.414(0.785)h = 1.11h in4
τ =
V
A
=
622
4.44h
=
140
h
τ =
Tc
J
=
Mc
J
=
1600(0.5)
1.11h
=
720.7
h
The shear stresses, τ and τ , are additive algebraically
τmax =
1
h
(140 + 720.7) =
861
h
psi
τmax = τall =
861
h
= 3000
h =
861
3000
= 0.287 → 5/16"
Decision: Use 5/16 in ﬁllet welds Ans.
100
16
3
562
266.7
266.7
462
F
FB
B
A
R
x
A
R
y
A
60Њ
y
x
shi20396_ch09.qxd 8/19/03 9:30 AM Page 263

9-25
For the pattern in bending shown, ﬁnd the centroid G of the weld group.
¯x =
6(0.707)(1/4)(3) + 6(0.707)(3/8)(13)
6(0.707)(1/4) + 6(0.707)(3/8)
= 9 in
I1/4 = 2 IG + A2
¯x
= 2
0.707(1/4)(63
)
12
+ 0.707(1/4)(6)(62
)
= 82.7 in4
I3/8 = 2
0.707(3/8)(63
)
12
+ 0.707(3/8)(6)(42
)
= 60.4 in4
I = I1/4 + I3/8 = 82.7 + 60.4 = 143.1 in4
The critical location is at B. From Eq. (9-3),
τ =
F
2[6(0.707)(3/8 + 1/4)]
= 0.189F
τ =
Mc
I
=
(8F)(9)
143.1
= 0.503F
τmax = τ 2 + τ 2 = F 0.1892 + 0.5032 = 0.537F
Materials:
A36 Member: Sy = 36 kpsi
1015 HR Attachment: Sy = 27.5 kpsi
E6010 Electrode: Sy = 50 kpsi
τall = 0.577 min(36, 27.5, 50) = 15.9 kpsi
F =
τall/n
0.537
=
15.9/2
0.537
= 14.8 kip Ans.
9-26 Figure P9-26b is a free-body diagram of the bracket. Forces and moments that act on the
welds are equal, but of opposite sense.
(a) M = 1200(0.366) = 439 lbf · in Ans.
(b) Fy = 1200 sin 30◦
= 600 lbf Ans.
(c) Fx = 1200 cos 30◦
= 1039 lbf Ans.
3
8
"
3
8
"
1
4
"
1
4
"
7"9"
g
g
g
g
y
x
G
B
shi20396_ch09.qxd 8/19/03 9:30 AM Page 264

Chapter 9 265
(d) From Table 9-2, category 6:
A = 1.414(0.25)(0.25 + 2.5) = 0.972 in2
Iu =
d2
6
(3b + d) =
2.52
6
[3(0.25) + 2.5] = 3.39 in3
The second area moment about an axis through G and parallel to z is
I = 0.707hIu = 0.707(0.25)(3.39) = 0.599 in4
Ans.
(e) Refer to Fig. P.9-26b. The shear stress due to Fy is
τ1 =
Fy
A
=
600
0.972
= 617 psi
The shear stress along the throat due to Fx is
τ2 =
Fx
A
=
1039
0.972
= 1069 psi
The resultant of τ1 and τ2 is in the throat plane
τ = τ2
1 + τ2
2
1/2
= (6172
+ 10692
)1/2
= 1234 psi
The bending of the throat gives
τ =
Mc
I
=
439(1.25)
0.599
= 916 psi
The maximum shear stress is
τmax = (τ 2
+ τ 2
)1/2
= (12342
+ 9162
)1/2
= 1537 psi Ans.
(f) Materials:
1018 HR Member: Sy = 32 kpsi, Sut = 58 kpsi (Table A-20)
E6010 Electrode: Sy = 50 kpsi (Table 9-3)
n =
Ssy
τmax
=
0.577Sy
τmax
=
0.577(32)
1.537
= 12.0 Ans.
(g) Bending in the attachment near the base. The cross-sectional area is approximately
equal to bh.
A1
.
= bh = 0.25(2.5) = 0.625 in2
τxy =
Fx
A1
=
1039
0.625
= 1662 psi
I
c
=
bd2
6
=
0.25(2.5)2
6
= 0.260 in3
At location A
σy =
Fy
A1
+
M
I/c
σy =
600
0.625
+
439
0.260
= 2648 psi
shi20396_ch09.qxd 8/19/03 9:30 AM Page 265

The von Mises stress σ is
σ = σ2
y + 3τ2
xy
1/2
= [26482
+ 3(1662)2
]1/2
= 3912 psi
Thus, the factor of safety is,
n =
Sy
σ
=
32
3.912
= 8.18 Ans.
The clip on the mooring line bears against the side of the 1/2-in hole. If the clip fills
the hole
σ =
F
td
=
−1200
0.25(0.50)
= −9600 psi
n = −
Sy
σ
= −
32(103
)
−9600
= 3.33 Ans.
Further investigation of this situation requires more detail than is included in the task
statement.
(h) In shear fatigue, the weakest constituent of the weld melt is 1018 with Sut = 58 kpsi
Se = 0.504Sut = 0.504(58) = 29.2 kpsi
Table 7-4:
ka = 14.4(58)−0.718
= 0.780
For the size factor estimate, we first employ Eq. (7-24) for the equivalent diameter.
de = 0.808
√
0.707hb = 0.808 0.707(2.5)(0.25) = 0.537 in
Eq. (7-19) is used next to find kb
kb =
de
0.30
−0.107
=
0.537
0.30
−0.107
= 0.940
The load factor for shear kc , is
kc = 0.59
The endurance strength in shear is
Sse = 0.780(0.940)(0.59)(29.2) = 12.6 kpsi
From Table 9-5, the shear stress-concentration factor is Kf s = 2.7. The loading is
repeatedly-applied.
τa = τm = kf
τmax
2
= 2.7
1.537
2
= 2.07 kpsi
Table 7-10: Gerber factor of safety nf , adjusted for shear, with Ssu = 0.67Sut
nf =
1
2
0.67(58)
2.07
2
2.07
12.6



−1 + 1 +
2(2.07)(12.6)
0.67(58)(2.07)
2



= 5.55 Ans.
Attachment metal should be checked for bending fatigue.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 266

Chapter 9 267
9-27 Use b = d = 4 in. Since h = 5/8 in, the primary shear is
τ =
F
1.414(5/8)(4)
= 0.283F
The secondary shear calculations, for a moment arm of 14 in give
Ju =
4[3(42
) + 42
]
6
= 42.67 in3
J = 0.707hJu = 0.707(5/8)42.67 = 18.9 in4
τx = τy =
Mry
J
=
14F(2)
18.9
= 1.48F
Thus, the maximum shear and allowable load are:
τmax = F 1.482 + (0.283 + 1.48)2 = 2.30F
F =
τall
2.30
=
20
2.30
= 8.70 kip Ans.
From Prob. 9-5b, τall = 11 kpsi
Fall =
τall
2.30
=
11
2.30
= 4.78 kip
The allowable load has thus increased by a factor of 1.8 Ans.
9-28 Purchase the hook having the design shown in Fig. P9-28b. Referring to text Fig. 9-32a,
this design reduces peel stresses.
9-29 (a)
¯τ =
1
l
l/2
−l/2
Pω cosh(ωx)
4b sinh(ωl/2)
dx
= A1
l/2
−l/2
cosh(ωx) dx
=
A1
ω
sinh(ωx)
l/2
−l/2
=
A1
ω
[sinh(ωl/2) − sinh(−ωl/2)]
=
A1
ω
[sinh(ωl/2) − (−sinh(ωl/2))]
=
2A1 sinh(ωl/2)
ω
=
Pω
4bl sinh(ωl/2)
[2 sinh(ωl/2)]
¯τ =
P
2bl
Ans.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 267

(b) τ(l/2) =
Pω cosh(ωl/2)
4b sinh(ωl/2)
=
Pω
4b tanh(ωl/2)
Ans.
(c)
K =
τ(l/2)
¯τ
=
Pω
4b sinh(ωl/2)
2bl
P
K =
ωl/2
tanh(ωl/2)
Ans.
For computer programming, it can be useful to express the hyperbolic tangent in terms
of exponentials:
K =
ωl
2
exp(ωl/2) − exp(−ωl/2)
exp(ωl/2) + exp(−ωl/2)
Ans.
9-30 This is a computer programming exercise. All programs will vary.
shi20396_ch09.qxd 8/19/03 9:30 AM Page 268

Capítulo 09 solda

More Related Content

What's hot (19)

Viewers also liked (14)

Similar to Capítulo 09 solda (20)

More from Jhayson Carvalho (8)

Recently uploaded (20)

Capítulo 09 solda