Cellular Networks in routing and switching

Wireless Networks Fall 2007
Cellular Networks

Cellular Network Organization
Use multiple low-power transmitters (100
W or less)
Areas divided into cells
o Each served by its own antenna
o Served by base station consisting of
transmitter, receiver, and control unit
o Band of frequencies allocated
o Cells set up such that antennas of all neighbors
are equidistant (hexagonal pattern)

Frequency Reuse
Adjacent cells assigned different
frequencies to avoid interference or
crosstalk
Objective is to reuse frequency in nearby
cells
o 10 to 50 frequencies assigned to each cell
o Transmission power controlled to limit power at
that frequency escaping to adjacent cells
o The issue is to determine how many cells must
intervene between two cells using the same
frequency

Cellular Concept
 Several small cells instead of a single transmitter=> frequency reuse: better efficiency
 Fixed Channel Allocation:
 Cluster of size N = i2+ij+j2; and D = sqrt(3N)R
 R cell radius and
 D distance at which a frequency can be reused with acceptable interference

Frequency Assignment Problems
 Cellular systems provider allocates frequencies
from a licensed spectrum
 Constraints:
o For any cell, interference from nearby cells within an
acceptable minimum
o For any cell, the frequency bandwidth allocated sufficient
to support the load in the cell
 Objectives:
o Minimize the total bandwidth (or width of the spectrum)
allocated across all cells
o Minimize call blocking probability
o Minimize average interference

Solving FAPs
 Since the programs are all integer programs, hard
to solve in general
o NP-hard
 Can apply standard mathematical programming
heuristics
o Branch and bound
o Cutting plane techniques
o Local search
o Simulated annealing
o Tabu search…
 Some problems can be expressed as graph
coloring problems in specialized graphs

Formulating FAPs
 Can be expressed as mathematical programs
o Mostly linear
o Some non-linear (e.g., minimizing interference)
 Approach:
o Represent the cellular structure as a graph
o Each node represents a cell (center)
o Interference relationships represented by the graph
edges
o Assigning a frequency same as assigning a fixed-width
band centered around the frequency
o Binary variables that indicate whether a (center)
frequency is assigned

Approaches to Cope with
Increasing Capacity
 Adding new channels
 Frequency borrowing – frequencies are taken
from adjacent cells by congested cells
 Cell splitting – cells in areas of high usage can be
split into smaller cells
 Cell sectoring – cells are divided into a number of
wedge-shaped sectors, each with their own set of
channels
 Microcells – antennas move to buildings, hills, and
lamp posts

Cellular System Overview

Cellular Systems Terms
 Base Station (BS) – includes an antenna, a
controller, and a number of receivers
 Mobile telecommunications switching office
(MTSO) – connects calls between mobile units
 Two types of channels available between mobile
unit and BS
o Control channels – used to exchange information having
to do with setting up and maintaining calls
o Traffic channels – carry voice or data connection between
users

Steps in an MTSO Controlled Call
between Mobile Users
Mobile unit initialization
Mobile-originated call
Paging
Call accepted
Ongoing call
Handoff

Additional Functions in an MTSO
Controlled Call
Call blocking
Call termination
Call drop
Calls to/from fixed and remote mobile
subscriber

Mobile Radio Propagation Effects
Signal strength
o Must be strong enough between base station
and mobile unit to maintain signal quality at
the receiver
o Must not be so strong as to create too much
cochannel interference with channels in another
cell using the same frequency band
Fading
o Signal propagation effects may disrupt the
signal and cause errors

Handoff Performance Metrics
Cell blocking probability – probability of a
new call being blocked
Call dropping probability – probability that
a call is terminated due to a handoff
Call completion probability – probability
that an admitted call is not dropped before
it terminates
Probability of unsuccessful handoff –
probability that a handoff is executed while
the reception conditions are inadequate

Handoff Performance Metrics
 Handoff blocking probability – probability that
a handoff cannot be successfully completed
 Handoff probability – probability that a handoff
occurs before call termination
 Rate of handoff – number of handoffs per unit
time
 Interruption duration – duration of time during
a handoff in which a mobile is not connected to
either base station
 Handoff delay – distance the mobile moves
from the point at which the handoff should
occur to the point at which it does occur

Handoff Strategies Used to
Determine Instant of Handoff
Relative signal strength
Relative signal strength with threshold
Relative signal strength with hysteresis
Relative signal strength with hysteresis
and threshold
Prediction techniques

Power Control
Design issues making it desirable to
include dynamic power control in a cellular
system
o Received power must be sufficiently above the
background noise for effective communication
o Desirable to minimize power in the transmitted
signal from the mobile
• Reduce cochannel interference, alleviate health
concerns, save battery power
o In SS systems using CDMA, it’s desirable to
equalize the received power level from all
mobile units at the BS

Types of Power Control
Open-loop power control
o Depends solely on mobile unit
o No feedback from BS
o Not as accurate as closed-loop, but can react
quicker to fluctuations in signal strength
Closed-loop power control
o Adjusts signal strength in reverse channel
based on metric of performance
o BS makes power adjustment decision and
communicates to mobile on control channel

Traffic Engineering
Ideally, available channels would equal
number of subscribers active at one time
In practice, not feasible to have capacity
handle all possible load
For N simultaneous user capacity and L
subscribers
o L < N – nonblocking system
o L > N – blocking system

Blocking System Performance
Questions
Probability that call request is blocked?
What capacity is needed to achieve a
certain upper bound on probability of
blocking?
What is the average delay?
What capacity is needed to achieve a
certain average delay?

Traffic Intensity
Load presented to a system:
•  = mean rate of calls attempted per unit time
• h = mean holding time per successful call
• A = average number of calls arriving during average
holding period
h
A 


Capacity in Cellular Systems
 Blocking Probability (Grade Of Service): Erlang B
formula
 Based on the above formula, we can determine
the minimum N needed to support a desired
grade of service.
 
 C
n
n
C
n
A
C
A
GOS
0
!
/
!
/

Factors that Determine the Nature
of the Traffic Model
Manner in which blocked calls are handled
o Lost calls delayed (LCD) – blocked calls put in a
queue awaiting a free channel
o Blocked calls rejected and dropped
• Lost calls cleared (LCC) – user waits before another
attempt
• Lost calls held (LCH) – user repeatedly attempts
calling
Number of traffic sources
o Whether number of users is assumed to be
finite or infinite

First-Generation Analog
Advanced Mobile Phone Service (AMPS)
o In North America, two 25-MHz bands allocated
to AMPS
• One for transmission from base to mobile unit
• One for transmission from mobile unit to base
o Each band split in two to encourage
competition (12.5MHz per operator)
o Channels of 30 KHz: 21 control channels (FSK),
395 traffic channels (FM voice) per operator
o Frequency reuse exploited (N = 7)

AMPS Operation
 Subscriber initiates call by keying in phone
number and presses send key
 MTSO verifies number and authorizes user
 MTSO issues message to user’s cell phone
indicating send and receive traffic channels
 MTSO sends ringing signal to called party
 Party answers; MTSO establishes circuit and
initiates billing information
 Either party hangs up; MTSO releases circuit,
frees channels, completes billing

Differences Between First and
Second Generation Systems
 Digital traffic channels – first-generation systems
are almost purely analog; second-generation
systems are digital
 Encryption – all second generation systems
provide encryption to prevent eavesdropping
 Error detection and correction – second-
generation digital traffic allows for detection and
correction, giving clear voice reception
 Channel access – second-generation systems
allow channels to be dynamically shared by a
number of users

Sample TDMA Design Considerations
Number of logical channels per physical
channel (number of time slots in TDMA
frame): 8
Maximum cell radius (R): 35 km
Frequency: region around 900 MHz
Maximum vehicle speed (Vm):250 km/hr
Maximum coding delay: approx. 20 ms
Maximum delay spread (m): 10 s
Bandwidth: Not to exceed 200 kHz (25 kHz
per channel)

Architecture of the GSM system
 Several providers setup mobile networks following
the GSM standard within each country
 Components
o MS (mobile station)
o BS (base station)
o MSC (mobile switching center)
o LR (location register)
 Subsystems
o RSS (radio subsystem): covers all radio aspects
• Base station subsystem
o NSS (network and switching subsystem): call forwarding,
handover, switching
o OSS (operation subsystem): management of the network

GSM: elements and interfaces
NSS
MS MS
BTS
BSC
GMSC
IWF
OMC
BTS
BSC
MSC MSC
Abis
Um
EIR
HLR
VLR VLR
A
BSS
PDN
ISDN, PSTN
RSS
radio cell
radio cell
MS
AUC
OSS
signaling
O

Um
Abis
A
BSS
radio
subsystem
MS MS
BTS
BSC
BTS
BTS
BSC
BTS
network and
switching subsystem
MSC
MSC
Fixed partner networks
IWF
ISDN
PSTN
PDN
SS7
EIR
HLR
VLR
ISDN
PSTN
GSM: system architecture

Radio subsystem
 Components
o MS (Mobile Station)
o BSS (Base Station Subsystem):
consisting of
• BTS (Base Transceiver Station):
sender and receiver
• BSC (Base Station Controller):
controlling several transceivers
 Interfaces
o Um : radio interface
o Abis : standardized, open interface
with
16 kbit/s user channels
o A: standardized, open interface
with
64 kbit/s user channels
Um
Abis
A
BSS
radio
subsystem
network and switching
subsystem
MS MS
BTS
BSC MSC
BTS
BTS
BSC
BTS
MSC

Mobile Station
Mobile station communicates across Um
interface (air interface) with base station
transceiver in same cell as mobile unit
Mobile equipment (ME) – physical
terminal, such as a telephone or PDA
o ME includes radio transceiver, digital signal
processors and subscriber identity module
(SIM)
GSM subscriber units are generic until SIM
is inserted
o SIMs roam, not necessarily the subscriber
devices

Base Station Subsystem (BSS)
BSS consists of base station controller and
one or more base transceiver stations
(BTS)
Each BTS defines a single cell
o Includes radio antenna, radio transceiver and a
link to a base station controller (BSC)
BSC reserves radio frequencies, manages
handoff of mobile unit from one cell to
another within BSS, and controls paging

Network and switching subsystem
Components
 MSC (Mobile Services Switching Center):
 IWF (Interworking Functions)
 ISDN (Integrated Services Digital Network)
 PSTN (Public Switched Telephone Network)
 PSPDN (Packet Switched Public Data Net.)
 CSPDN (Circuit Switched Public Data Net.)
Databases
 HLR (Home Location Register)
 VLR (Visitor Location Register)
 EIR (Equipment Identity Register)
network
subsystem
MSC
MSC
fixed partner
networks
IWF
ISDN
PSTN
PSPDN
CSPD
N
SS7
EIR
HLR
VLR
ISDN
PSTN

Network Subsystem (NS)
Provides link between cellular network and
PSTNs
Controls handoffs between cells in different
BSSs
Authenticates users and validates accounts
Enables worldwide roaming of mobile users
Central element of NS is the mobile
switching center (MSC)

Mobile Switching Center (MSC)
Databases
 Home location register (HLR) database – stores
information about each subscriber that belongs to it
 Visitor location register (VLR) database – maintains
information about subscribers currently physically in
the region
 Authentication center database (AuC) – used for
authentication activities, holds encryption keys
 Equipment identity register database (EIR) – keeps
track of the type of equipment that exists at the
mobile station

TDMA Format – Time Slot Fields
 Trail bits – allow synchronization of transmissions
from mobile units located at different distances
 Encrypted bits – encrypted data
 Stealing bit - indicates whether block contains data
or is "stolen"
 Training sequence – used to adapt parameters of
receiver to the current path propagation
characteristics
o Strongest signal selected in case of multipath propagation
 Guard bits – used to avoid overlapping with other
bursts

GSM Speech Processing Steps
Speech compressed using a predictive
coding scheme
Divided into blocks, each of which is
protected partly by CRC and partly by a
convolutional code
Interleaving to protect against burst errors
Encryption for providing privacy
Assembled into time slots
Modulated for analog transmission using
FSK

Functions Provided by Protocols
Protocols above the link layer of the GSM
signaling protocol architecture provide
specific functions:
o Radio resource management
o Mobility management
o Connection management
o Mobile application part (MAP)
o BTS management

Mobile Terminated Call
PSTN
calling
station
GMSC
HLR VLR
BSS
BSS
BSS
MSC
MS
1 2
3
4
5
6
7
8 9
10
11 12
13
16
10 10
11 11 11
14 15
17
 1: calling a GSM subscriber
 2: forwarding call to GMSC
 3: signal call setup to HLR
 4, 5: connect with current
VLR
 6: forward responsible
MSC to GMSC
 7: forward call to current
MSC
 8, 9: get current status of MS
 10, 11: paging of MS
 12, 13: MS answers
 14, 15: security checks
 16, 17: set up connection

Mobile Originated Call
PSTN GMSC
VLR
BSS
MSC
MS
1
2
6 5
3 4
9
10
7 8
 1, 2: connection
request
 3, 4: security check
 5-8: check resources
(free circuit)
 9-10: set up call

MTC/MOC
BTS
MS
paging request
channel request
immediate assignment
paging response
authentication request
authentication response
ciphering command
ciphering complete
setup
call confirmed
assignment command
assignment complete
alerting
connect
connect acknowledge
data/speech exchange
BTS
MS
channel request
immediate assignment
service request
authentication request
authentication response
ciphering command
ciphering complete
setup
call confirmed
assignment command
assignment complete
alerting
connect
connect acknowledge
data/speech exchange
MTC MOC

4 types of handover
MSC MSC
BSC BSC
BSC
BTS BTS BTS
BTS
MS MS MS MS
1
2 3 4

Handover decision
receive level
BTSold
receive level
BTSold
MS MS
HO_MARGIN
BTSold BTSnew

Security in GSM
 Security services
o access control/authentication
• user  SIM (Subscriber Identity Module): secret PIN (personal identification
number)
• SIM  network: challenge response method
o confidentiality
• voice and signaling encrypted on the wireless link (after successful
authentication)
o anonymity
• temporary identity TMSI
(Temporary Mobile Subscriber Identity)
• newly assigned at each new location update (LUP)
• encrypted transmission
 3 algorithms specified in GSM
o A3 for authentication (“secret”, open interface)
o A5 for encryption (standardized)
o A8 for key generation (“secret”, open interface)
“secret”:
• A3 and A8
available via the
Internet
• network providers
can use stronger
mechanisms

GSM - authentication
A3
RAND
Ki
128 bit 128 bit
SRES* 32 bit
A3
RAND Ki
128 bit 128 bit
SRES 32 bit
SRES* =? SRES SRES
RAND
SRES
32 bit
mobile network SIM
AC
MSC
SIM
Ki: individual subscriber authentication key SRES: signed response

GSM - key generation and
encryption
A8
RAND
Ki
128 bit 128 bit
Kc
64 bit
A8
RAND Ki
128 bit 128 bit
SRES
RAND
encrypted
data
mobile network (BTS) MS with SIM
AC
BTS
SIM
A5
Kc
64 bit
A5
MS
data data
cipher
key

IS-95 (CdmaOne)
 IS-95: standard for the radio interface
 IS-41: standard for the network part
 Operates in 800MHz and 1900MHz bands
 Uses DS-CDMA technology (1.2288 Mchips/s)
 Forward link (downlink): (2,1,9)-convolutional code,
interleaved, 64 chips spreading sequence (Walsh-Hadamard
functions)
 Pilot channel, synchronization channel, 7 paging channels, up
to 63 traffic channels
 Reverse link (uplink): (3,1,9)-convolutional code, interleaved,
6 bits are mapped into a Walsh-Hadamard sequence,
spreading using a user-specific code
 Tight power control (open-loop, fast closed loop)

Advantages of CDMA Cellular
 Frequency diversity – frequency-dependent
transmission impairments have less effect on
signal
 Multipath resistance – chipping codes used for
CDMA exhibit low cross correlation and low
autocorrelation
 Privacy – privacy is inherent since spread
spectrum is obtained by use of noise-like signals
 Graceful degradation – system only gradually
degrades as more users access the system

Drawbacks of CDMA Cellular
Self-jamming – arriving transmissions
from multiple users not aligned on chip
boundaries unless users are perfectly
synchronized
Near-far problem – signals closer to the
receiver are received with less attenuation
than signals farther away
Soft handoff – requires that the mobile
acquires the new cell before it relinquishes
the old; this is more complex than hard
handoff used in FDMA and TDMA schemes

CDMA Design Considerations
RAKE receiver – when multiple versions of
a signal arrive more than one chip interval
apart, RAKE receiver attempts to recover
signals from multiple paths and combine
them
o This method achieves better performance than
simply recovering dominant signal and treating
remaining signals as noise
Soft Handoff – mobile station temporarily
connected to more than one base station
simultaneously

Forward Link Channels
 Pilot: allows the mobile unit to acquire timing
information, provides phase reference and
provides means for signal strength comparison
 Synchronization: used by mobile station to obtain
identification information about cellular system
 Paging: contain messages for one or more mobile
stations
 Traffic: the forward channel supports 55 traffic
channels

Forward Traffic Processing Steps
Speech is encoded at a rate of 8550 bps
Additional bits added for error detection
Data transmitted in 2-ms blocks with
forward error correction provided by a
convolutional encoder
Data interleaved in blocks to reduce effects
of errors
Data bits are scrambled, serving as a
privacy mask
o Using a long code based on user’s electronic
serial number

Forward Traffic Processing Steps
 Power control information inserted into traffic
channel
 DS-SS function spreads the 19.2 kbps to a rate of
1.2288 Mbps using one row of 64 x 64 Walsh
matrix
 Digital bit stream modulated onto the carrier
using QPSK modulation scheme

Reverse Traffic Processing Steps
 Convolutional encoder at rate 1/3
 Spread the data using a Walsh matrix
o Use a 6-bit piece of data as an index to the Walsh matrix
o To improve reception at base station
 Data burst randomizer
 Spreading using the user-specific long code mask

Third-Generation Capabilities
 Voice quality comparable to the public switched
telephone network
 144 kbps data rate available to users in high-
speed motor vehicles over large areas
 384 kbps available to pedestrians standing or
moving slowly over small areas
 Support for 2.048 Mbps for office use
 Symmetrical/asymmetrical data transmission rates
 Support for both packet switched and circuit
switched data services

Cellular Networks in routing and switching

More Related Content

Similar to Cellular Networks in routing and switching (20)

More from Irfan Ali (6)

Recently uploaded (20)

Cellular Networks in routing and switching