![IS:13920 – 2016
•Major Changes
– Scope
•Ductile Design and Detailing of RC Structures
– Collapse Mechanism
•Column-Beam Strength Ratio b
– Shear Design of Beam-Column Joints
•Minimum Column Size Max[300 mm; 20db]
– Flexural Strength of Structural Walls
•Principle of Superposition
– Mechanical Couplers](https://image.slidesharecdn.com/changesinis1893andis13920-230214161856-1c0970ad/85/Changes-in-IS-1893-and-IS-13920-pdf-36-320.jpg)
Changes in IS 1893 and IS 13920.pdf
- 1. IS 1893 and IS 13920 Codal Changes Reading between the lines… Alpa Sheth
- 3. a) Design spectra extended up to natural period up of 6 s; b) Same design response spectra for all buildings, irrespective of the material of construction (for steel and concrete); c) New method for arriving at the approximate natural period of buildings d) Response Reduction Factors Revised; Buildings with flat slabs included; e) Minimum design lateral force Changes In Estimation Of The Hazard
- 4. f) Load combinations consistent with other codes; g) Temporary structures included h) Importance factor provisions to acknowledge the density and business continuity; i) Design Vertical Acceleration Coefficient Av Changes In Estimation Of The Hazard
- 5. II. Changes in Estimation of Resistance Capacity j) How to handle different types of irregularity of structural system; k) Effect of masonry infill; l) Use of Cracked Section Properties Ieff m) Torsional provisions revised; n) Simplified method for liquefaction potential analysis. o) Open Ground Storey structures requirements revised
- 6. BACKDROP • Code is a consensus document • Collective wisdom of the drafting group, modified by larger committee and public comments • Open to modifications in next revision • Code need extensive usage for evaluating its ease of applicability and limitations
- 7. Design Horizontal Earthquake Force 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4 5 6 Natural Period T (s) Sa/g Type I: Rock or Hard Soil Type II: Medium Soil Type III: Soft Soil Spectral Shape Sa/g Figure 2: Design Acceleration Coefficient (Sa /g) (corresponding to 5% damping) for use in (a) Equivalent Static Method, and (b) Response Spectrum Method a b
- 8. Design Horizontal Earthquake Force 5% damping for all structures – Design force independent of material of construction •Steel, RC and Masonry – Earlier 2% for Steel, 5% for RC, 7% for Masonry Note: Damping for Wind Conditions different!!!
- 9. Steel Structures now less punished • New Code is more attractive for Steel Structures. – Damping increase from 2% to 5% and R factor from 4 to 5. Thus reduction in seismic coefficient by 1.4*5/4 =1.75 times
- 10. Design Horizontal Earthquake Force-New Natural Period Empirical Formula >
- 11. New Natural Period Empirical Formula for Shear Wall Buildings Gives realistic, higher Natural Period for building with walls structures of lesser stiffness Building ht h 45 m 15 storeys Building depth d 30m Building Width b 20m Tx (s) =0.09h/sqrt(d) = 0.74 (equation for non-frame structures) Tx (S) =0.1n= 1.5 (not applicable for non- frame structures) Wall Thk (m) Length (m) Lwi Area (m2)Awi Lwi/h Awi(0.2+Lwi/h)^2 0.3 5 1.5 0.111 0.145 0.25 6 1.5 0.133 0.167 0.3 3 0.9 0.067 0.064 0.25 7 1.75 0.156 0.221 0.25 4 1 0.089 0.083 0.3 3.5 1.05 0.078 0.081 0.3 6.5 1.95 0.144 0.231 SAwi= 9.65 Aw= 0.9929 Tx =0.075h^0.75/sqrt(Aw) = 1.31s Tx= 1.31s New Alternative equation T for wall structures As per 7.6.2 c) Ty=0.09h/sqrt(b) = 0.9s As per 7.6.2 b) Ty=0.99s (SAwi=18.3m2, Aw=1.72) T (s) As per 7.6.2c As per 7.6.2b % walls ( Sawi/ (bxd) Tx (s) 0.74 1.31 0.71 Ty (s) 0.9 0.99 1.4 As SAwi>2%, equations merge, and b) will give T less than that from c)
- 12. Defining Building height h • h = Height (in m) of building. This excludes the basement storeys, where basement storey, walls are connected with the ground floor deck or fitted between the building columns, but includes the basement storeys, when they are not so connected. h h
- 13. R - Same for Steel & RC Buildings
- 14. Special Provision for Flat Slab Structures (Response Reduction Factor R)
- 15. Minimum Design Lateral Force • Min design lateral force ~ 25% of the applicable Ah in the zone (at PGA)
- 16. IMPORTANCE FACTOR • Increased to 1.2 for buildings >200 persons occupancy.(That’s buildings with more than 50 apartments) • Will affect PMAY buildings which are high density, low cost • Ironically low cost housing has lesser loads (1.5kN/m2 Live load as vs 2 kN/m2 in non low cost housing)
- 17. Av Vertical seismic coeff Not same as Ah 2/3 of Ah at PGA (at Ta=0)
- 18. Modal Mass Participation Factors May not be possible in Buildings with large podiums!!!
- 19. • Cracked Section Stiffness Properties • Irregularities • Code has become more stringent and punitive for stiffness irregularity Earthquake- Capacity Side
- 20. Cracked Section Properties Defined… • Ieff (cracked) =0.7 Igross for columns and walls • Ieff (cracked) =0.35 Igross for beams
- 21. Irregularities • Torsional Irregularity – Max and min displacements on floor differ by over 50% • Torsional Irregularity- First mode is in torsion • Plan Stiffness irregularity- Stiffness on floor below must be more than that on floor above. (In Tall buildings code – relaxed to 70%) • Plan Mass Irregularity- Mass above >1.5 times mass on floor below. • Plan Weak Storey – Strength less than floor above. FLOATING COLUMNS PROHIBITED IN SMRF
- 23. Diaphragm Flexibility 7.6.4 Diaphragm • In buildings whose floor diaphragms cannot provide rigid horizontal diaphragm action in their own plane, design storey shear shall be distributed to the various vertical elements of lateral force resisting system considering the in-plane flexibility of the diaphragms. • A floor diaphragm shall be considered to be flexible, if it deforms such that the maximum lateral displacement measured from the chord of the deformed shape at any point of the diaphragm is more than 1.2 times the average displacement of the entire diaphragm (see Fig. 6). • Usually, reinforced concrete monolithic slab-beam floors or those consisting of prefabricated or precast elements with reasonable reinforced screed concrete (at least a minimum of 50 mm on floors and of 75 mm on roof, with at least a minimum reinforcement of 6 mm bars spaced at 150 mm centres) as topping, and of plan aspect ratio less than 3, can be considered to be providing rigid diaphragm action.
- 24. Horizontal Irregularity •Re-entrant Corners In buildings with re-entrant corners, three-dimensional dynamic analysis method shall be adopted •Floor Slabs having Excessive Cut-Outs or Openings In buildings with discontinuity in their in-plane stiffness, if the area of the geometric cut-out is, a) less than or equal to 50 percent, the floor slab shall be taken as rigid or flexible depending on the location of and size of openings; and b) more than 50 percent, the floor slab shall be taken as flexible •Buildings with non-parallel lateral force resisting system shall be analyzed for load combinations mentioned in 6.3.2.2 or 6.3.4.1. •In a building with out-of-plane offsets in vertical elements, following two conditions shall be satisfied, if building is located in Seismic Zone III, IV or V: (a) Lateral drift shall be less than 0.2% in the storey having the offset and in the storeys below; and (b) Specialist literature shall be referred for removing the irregularity arising due to out-of-plane offsets in vertical elements.
- 26. Vertical Irregularity i) Stiffness Irregularity (Soft Storey) A soft storey is a storey whose lateral stiffness is less than that of the storey above. The structural plan density (SPD) shall be estimated when unreinforced masonry infills are used. When SPD of masonry infills exceeds 20 percent, the effect of URM infills shall be considered by explicitly modelling the same in structural analysis (as per 7.9). The design forces for RC members shall be larger of that obtained from analysis of: a) Bare Frame, and b) Frames with URM Infills, using 3D modeling of the structure. In buildings designed considering URM infills, the inter-storey drift shall be limited to 0.2 percent in the storey with stiffening and also in all storeys below.
- 27. Vertical Irregularity Mass Irregularity Mass irregularity shall be considered to exist, when the seismic weight (as per 7.7) of any floor is more than 150 percent of that of the floors below. In buildings with mass irregularity and located in Seismic Zones III, IV and V, the earthquake effects shall be estimated by Dynamic Analysis Method (as per 7.7). Vertical Geometric Irregularity Vertical geometric irregularity shall be considered to exist, when the horizontal dimension of the lateral force resisting system in any storey is more than 125 percent of the storey below. In buildings with vertical geometric irregularity and located in Seismic Zones III, IV and V, the earthquake effects shall be estimated by Dynamic Analysis Method (as per 7.7).
- 28. Vertical Irregularity In-Plane Discontinuity in Vertical Elements Resisting Lateral Force In-plane discontinuity in vertical elements which are resisting lateral force shall be considered to exist, when in-plane offset of the lateral force resisting elements is greater than 20 percent of the plan length of those elements, …. in Seismic Zones III, IV and V, buildings with in-plane discontinuity shall not be permitted. v) Strength Irregularity (Weak Storey) A weak storey is a storey whose lateral strength is less than that of the storey above. In such a case, buildings in Seismic Zones III, IV and V shall be designed such that safety of the building is not jeopardized; also, provisions of 7.10 shall be followed
- 29. How much wall area in Shear Wall Structures ? Country Wall Density (Total) Min in each direction Kyrgyzstan 15% 6.5% Turkey 4-12% 2-6% Chile 3-6% 1.5-3% Romania 12-14% 6-7% Colombia 3-5% 1.5% India 1-4%? 0.5-3%? Min 1.5%-2% in each direction is desirable for Zones IV and V
- 30. Ref: CONCRETE SHEAR WALL CONSTRUCTION M. Ofelia Moroni, University of Chile, Santiago, Chile (eeri.org) Chile Romania Typical Layouts…
- 31. When to consider URM panels in analysis and design? • Structural Plan Density of unreinforced masonry infill walls > 20%, URM walls to be considered in design • Not usually the case!!! Golcuk, 2000
- 32. How to include URM infill wall stiffness
- 33. Effect of URM infill wall stiffness 500x500 columns, 300x500 beams, 230 thk masonry wall/230 thick RC wall T=0.18s T=0.142s T=0.041s k=62 k=100 k=1200
- 34. RC Frame Buildings with Open Storeys In such buildings measures shall be adopted, which increase both stiffness and strength like: a) RC structural walls, or b) Braced frames, in select bays When the RC structural walls are provided, they shall: a) Be founded on properly designed foundations; b) Be continuous preferably over full height of building; and c) Be connected preferably to the moment resisting frame of building. d) Not cause additional torsional irregularity in plan than already present
- 35. RC Frame Buildings with Open Storeys e) Lateral stiffness in the open storey(s) >80 percent of that in the storey above; and f) Lateral strength in the open storey(s) > 90 percent of that in the storey above. g) Have at least 2 percent (SPD) along each principal direction in Seismic Zones III, IV and V and well distributed in the plan of the building along each direction.
- 36. IS:13920 – 2016 •Major Changes – Scope •Ductile Design and Detailing of RC Structures – Collapse Mechanism •Column-Beam Strength Ratio b – Shear Design of Beam-Column Joints •Minimum Column Size Max[300 mm; 20db] – Flexural Strength of Structural Walls •Principle of Superposition – Mechanical Couplers
- 37. IS 13920-2016
- 38. 1.1.3 All RC frames, RC walls and their elements in a structure need not be designed to resist lateral loads and the designer can judiciously identify the lateral load resisting system based on relative stiffness and location in the building and design those members for full lateral force.
- 39. How to identify LRFS • Select only those frames or shear walls as part of LFRS (in a direction) which participate significantly (Base Shear distribution is a good indicator for this). • Identify what % (x) of lateral load these frames these together carry (Should be in range of 90%+). • Scale lateral force by 100/x - to ensure the selected system is capable of carrying at least 100% of force in considered direction
- 40. SELECT APPROPRIATE SYSTEM… • Pictures of two buildings
- 41. SELECT APPROPRIATE SYSTEM… • Proportion selected frames accordingly so as to take ~85-90+% of base shear.
- 42. Also…. • 1.1.3 …….RC monolithic members assumed not to participate in the lateral force resisting system (see 3.7) shall be permitted provided that their effect on the seismic response of the system is accounted for. Consequence of failure of structural and non-structural members not part of the lateral force resisting system shall also be considered in design.
- 43. Gravity Columns… • Design gravity columns as per Section 11. – Gravity columns in buildings shall be detailed according to 11.1 and 11.2 for bending moments induced when subjected to “R” times the design lateral displacement under the factored equivalent static design seismic loads given by IS 1893 (Part 1).
- 44. HOW TO…. • Run the model for R times lateral loads and check gravity columns for these bending moments. Its almost always still an insignificant stress ratio and more economical to design for, than providing ductile detailing.
- 45. What’s not new but has been ignored all along… 5.1 The design and construction of reinforced concrete buildings shall be governed by provisions of IS 456, except as modified by the provisions of this standard for those elements participating in lateral force resistance.
- 46. What IS 456 say about walls.. 2
- 47. WALLS or COLUMN? • WHAT THIS MEANS – Any member that is desired to be defined as a wall as per IS 456 may not have axial stress ratio greater than say 0.28fck – that is to say it cannot be governed by min reinforcement of rv =0.12% and rh=0.2% if the above axial stress ratio is exceeded – In such a case all requirements of Columns as per IS 456 are applicable (min rv =0.8% ….)???
- 48. Beam Width For the first time, explicitly acknowledged that beam may be wider than column as long as transverse reinforcement in continued into beam column joint. Great relief for some situations and to ease congestion in beam-column joint.
- 49. Mechanical Couplers • Use of mechanical couplers allows for modular and mechanised construction- • Lapping bars anywhere and all together
- 50. Min Link Diameter • Link min dia for beams and columns to be 8 mm. • Encouraging better shear capacity • Acknowledging the corrosion effect on shear capacity of members
- 51. Columns Probably the most important change in the code • The factored axial compressive stress considering all load combinations relating to seismic loads shall be limited to 0.40 fck in all such members, except in those covered under 10. • This will perforce require larger sectional size of column or use of higher mix of concrete!
- 52. Limiting Column Axial Stress Ratio • Lesser axial stress ratio will result in lesser percentage reinforcement demand even in case of higher bending stress and will improve column behaviour. • Special Confining reinforcement- Max spacing of links = 100mm
- 53. Ensuring Development of Beam Reinforcement • Min dimension of column =20 db, db = max beam bar dia for exterior columns • E.g. Beam Bar dia=20, Column Size=400
- 54. Stress on Collapse Mechanism • All damage in one storey Distributed damage in all storeys
- 55. SHEAR WALLS • MIN thickness =300 for coupled walls to avoid congestion due to coupling beam steel. • Special Shear walls must be founded on foundations- i.e. floating special shear walls are not allowed!!!
- 56. Shear walls
- 57. Shear Wall Boundary Elements Much relief in Boundary Elements design. More relaxed than SMRF columns For columns
- 58. Shear Wall Boundary Elements Much relief in Boundary Elements design. More relaxed than SMRF columns For columns sv 100 mm h 160 mm fck 30 N/mm2 fy 500 N/mm2 Ag 2800 cm2 40x70 Ak 1800 cm2 30x60 Ash 96 mm 48 mm For walls boundary elements 1 2 2 1
- 59. Gravity Columns confinement and shear capacity requirements • 11.1 The provisions in 11.1.1 and 11.1.2 shall be satisfied, when induced bending moments and horizontal shear forces under the said lateral displacement combined with factored gravity bending moment and shear force do not exceed the design moment of resistance and design lateral shear capacity of the column. – 11.1.1 Gravity columns shall satisfy 7.3.2, 7.4.1 and 7.4.2. But, spacing of links along the full column height shall not exceed 6 times diameter of smallest longitudinal bar or 150 mm. – 11.1.2 Gravity columns with factored gravity axial stress exceeding 0.4fck shall satisfy 11.1.1 and shall have transverse reinforcement at least one half of special confining reinforcement required by 8.
- 60. Acknowledging confinement effect of joints
- 61. Graphics of slides 49, 52, 56 courtesy CVR Murty