CCNAv5 - S3: Chapter8 EIGRP Advanced Configurations and Troubleshooting

© 2008 Cisco Systems, Inc. All rights reserved. Cisco ConfidentialPresentation_ID 1
Chapter 8: EIGRP
Advanced
Configurations and
Troubleshooting
Scaling Networks

Presentation_ID 2© 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential
Chapter 8
8.1 Advanced EIGRP Configurations
8.2 Troubleshooting EIGRP
8.3 Summary

Chapter 8: Objectives
After completing this chapter, you will be able to:
 Configure EIGRP automatic summarization.
 Configure EIGRP manual summarization.
 Configure a router to propagate a default route in an EIGRP
network.
 Modify EIGRP interface settings to improve network performance.
 Configure EIGRP authentication to ensure secure routing updates.
 Explain the process and tools used to troubleshoot an EIGRP
network.
 Troubleshoot neighbor adjacency issues in an EIGRP network.
 Troubleshoot missing route entries in an EIGRP routing table.

Automatic Summarization
Network Technology

EIGRP Automatic Summarization

Configuring EIGRP Automatic Summarization
 EIGRP for IPv4 automatic summarization is disabled, by default,
beginning with Cisco IOS Release 15.0(1)M and 12.2(33). Prior to
this, automatic summarization was enabled, by default.
 To enable automatic summarization for EIGRP, use the auto-
summary command in router configuration mode.
R1(config)# router eigrp autonomous-system
R1(config-router)# auto-summary
 Use the no form of this command to disable autosummarization.
R1(config)# router eigrp autonomous-system
R1(config-router)# no auto-summary

Autosummarization
Verifying Autosummarization: show ip
protocols

Autosummarization
Verifying Autosummarization: Topology
Table

Autosummarization
Verifying Autosummarization: Routing
Table

Autosummarization
Summary Route

Autosummarization
Summary Route (cont.)

Manual Summarization
Manual Summary Routes
 EIGRP can be configured to summarize routes, whether or not
autosummarization is enabled.
 Because EIGRP is a classless routing protocol and includes the
subnet mask in the routing updates, manual summarization can
include supernet routes.
 A supernet is an aggregation of multiple major classful network
addresses.

Configuring EIGRP Manual Summary Routes

Verifying Manual Summary Routes

EIGRP for IPv6: Manual Summary Routes

Default Route Propagation
Propagating a Default Static Route
 Using a static route to 0.0.0.0/0 as a default route is not routing
protocol-dependent.
 The quad zero static default route can be used with any currently
supported routing protocols.
 The static default route is usually configured on the router that has
a connection to a network outside the EIGRP routing domain, for
example, to an ISP.

Verifying the Propagated Default Route
The entry for the EIGRP-learned default route is identified by the
following:
 D – This route was learned from an EIGRP routing update.
 * – The route is a candidate for a default route.
 EX – The route is an external EIGRP route; in this case, a static
route outside of the EIGRP routing domain.
 170 – This is the administrative distance of an external EIGRP
route.

EIGRP for IPv6- Default Route
Note: Some IOSs may require that the redistribute static command
include the EIGRP metric parameters and maximum transmission
unit (MTU) before the static route can be redistributed. These
parameters may vary, but an example for this scenario would be:
R2(config)# ipv6 router eigrp 2
R2(config-router)# redistribute static metric 64 2000
255 1 1500

Fine-tuning EIGRP Interfaces
EIGRP Bandwidth Utilization
EIGRP Bandwidth for IPv4
 By default, EIGRP uses only up to 50% of an interface’s bandwidth
for EIGRP information, which prevents the EIGRP process from
overutilizing a link and not allowing enough bandwidth for the
routing of normal traffic.
 The ip bandwidth-percent eigrp command can be used to
configure the percentage of bandwidth that may be used by EIGRP
on an interface.
Router(config-if)# ip bandwidth-percent eigrp as-number
percent

EIGRP Bandwidth Utilization (cont.)
EIGRP Bandwidth for IPv6
To configure the percentage of bandwidth that may be used by
EIGRP for IPv6 on an interface, use the ipv6 bandwidth-percent
eigrp command in interface configuration mode. To restore the
default value, use the no form of this command.
Router(config-if)# ipv6 bandwidth-percent eigrp as-
number percent

Hello and Hold Timers

Load Balancing IPv4
 Equal-cost load balancing is the ability of a router to distribute
outbound traffic using all interfaces that have the same metric from
the destination address.
 The Cisco IOS will, by default, allow load balancing using up to
four equal-cost paths; however, this can be modified. Using the
maximum-paths router configuration mode command, up to 32
equal-cost routes can be kept in the routing table.
Router(config-router)# maximum-paths value
 If the value is set to 1, load balancing is disabled.

Load Balancing IPv6

Secure EIGRP
Routing Protocol Authentication Overview
 Network administrators must be aware that routers are at risk from
attack just as much as end-user devices. Anyone with a packet
sniffer, such as Wireshark, can read information propagating
between routers.
 A method to protect routing information on the network is to
authenticate routing protocol packets using the Message Digest 5
(MD5) algorithm.
 Routing protocols, such as RIPv2, EIGRP, OSPF, IS-IS, and BGP
all support various forms of MD5 authentication.

Secure EIGRP
Configuring EIGRP with MD5 Authentication

Secure EIGRP
EIGRP Authentication Example

Secure EIGRP
EIGRP Authentication Example (cont.)

Secure EIGRP
Verifying Authentication
 Adjacencies are only formed when both connecting devices have
authentication configured.
 To verify that the correct EIGRP adjacencies were formed after
being configured for authentication, use the show ip eigrp
neighbors command on each router.
 To verify the neighbor adjacencies EIGRP for IPv6, use the show
ipv6 eigrp neighbors command.

Components of Troubleshooting EIGRP
Basic EIGRP Troubleshooting Commands
EIGRP for IPv4
 Router# show ip eigrp neighbors
 Router# show ip route
 Router# show ip protocols
EIGRP for IPv6
 Router# show ipv6 eigrp neighbors
 Router# show ipv6 route
 Router# show ipv6 protocols

Components of Troubleshooting EIGRP
Components

Troubleshoot EIGRP Neighbor Issues
Layer 3 Connectivity
A prerequisite for a neighbor adjacency to form between
two directly connected routers is Layer 3 connectivity.

EIGRP Parameters
When troubleshooting an EIGRP network, one of the first things to
verify is that all routers that are participating in the EIGRP network
are configured with the same autonomous system number.
EIGRP for IPv4
 Router# show ip protocols
EIGRP for IPv6
 Router# show ipv6 protocols

EIGRP Interfaces
 In addition to verifying the autonomous system number, it is
necessary to verify that all interfaces are participating in the EIGRP
network.
 The network command that is configured under the EIGRP routing
process indicates which router interfaces participate in EIGRP.

Troubleshoot EIGRP Routing Table Issues
Passive Interface
 One reason that route tables may not reflect the correct routes is
due to the passive-interface command.
 The show ip protocols can be used to check if an interface is
configured as passive.

Passive Interface
 With EIGRP running on a network, the passive-interface
command stops both outgoing and incoming routing updates. For
this reason, routers do not become neighbors.

Missing Network Statement

Missing Network Statement (cont.)
10.10.10.0/24 R1 Updates

Missing Network Statement (cont.)
Add Missing Network Statement

Troubleshooting EIGRP Routing Table Issues
Autosummarization
 Another issue that may create problems for the network
administrator is EIGRP autosummarization.
 EIGRP for IPv4 can be configured to automatically summarize
routes at classful boundaries. If there are discontiguous networks,
autosummarization causes inconsistent routing.
 Classful networks do not exist in IPv6; therefore, EIGRP for IPv6
does not support autosummarization. All summarization must be
accomplished using EIGRP manual summary routes.

Chapter 8: Summary
 EIGRP is one of the routing protocols commonly used in large
enterprise networks.
 Modifying EIGRP features and troubleshooting problems is one of
the most essential skills for a network engineer involved in the
implementation and maintenance of large, routed enterprise
networks that use EIGRP.
 Summarization decreases the number of entries in routing updates
and lowers the number of entries in local routing tables. It also
reduces bandwidth utilization for routing updates and results in faster
routing table lookups.
 EIGRP for IPv4 autosummarization is disabled, by default, beginning
with Cisco IOS Release 15.0(1)M and 12.2(33). Prior to this,
autosummarization was enabled, by default.

CCNAv5 - S3: Chapter8 EIGRP Advanced Configurations and Troubleshooting

More Related Content

What's hot (20)

Viewers also liked (19)

Similar to CCNAv5 - S3: Chapter8 EIGRP Advanced Configurations and Troubleshooting (20)

More from Vuz Dở Hơi (20)

Recently uploaded (20)

CCNAv5 - S3: Chapter8 EIGRP Advanced Configurations and Troubleshooting