CH EN 3453 Heat Transfer 2014 Fall Utah Homework HW 04 Solutions
- 1. QUESTION 1. Part a) Define the following terms (3 pts each): (i) Isotherm (ii) Heat flow line (iii) Adiabat (iv) Shape factor (v) Nodal point Part b) How are isotherms, adiabats and heat flow lines related? (5 pts) ANSWER Part a) (i) Isotherm – A vector that is everywhere perpendicular to lines of constant temperature. (ii) Heat flow line – The directions of a heat flux vector are represented by heat flow lines, and the vector itself is the resultant of heat flux components in the x- and y-directions. (iii) Adiabat – This is another term for specific heat flow lines, where no heat can be conducted across a heat flow line. (iv) Shape factor – A factor used to quickly solve two- and three-dimensional conduction problems. The symbol, S, is a steady state dimensionless conduction heat rate term. (v) Nodal point – Also called a node, this is a reference point used in numerical solutions. The aggregate of nodal points is called a nodal network. Part b) Heat flow lines could be termed as adiabats, given that conduction heat transfer does not occur across the heat line. Plotting temperature versus position allows isotherms to be constructed in the x-direction and heat flow lines to be the heat flux vector in the direction of heat transfer. (See Figure 4.1 on page 202 if Incropera, et. al. 6/e)
- 2. Excerpts from this work may be reproduced by instructors for distribution on a not-for-profit basis for testing or instructional purposes only to students enrolled in courses for which the textbook has been adopted. Any other reproduction or translation of this work beyond that permitted by Sections 107 or 108 of the 1976 United States Copyright Act without the permission of the copyright owner is unlawful.
- 3. Excerpts from this work may be reproduced by instructors for distribution on a not-for-profit basis for testing or instructional purposes only to students enrolled in courses for which the textbook has been adopted. Any other reproduction or translation of this work beyond that permitted by Sections 107 or 108 of the 1976 United States Copyright Act without the permission of the copyright owner is unlawful.
- 4. PROBLEM 4.9 KNOWN: Heat generation in a buried spherical container. FIND: (a) Outer surface temperature of the container, (b) Representative isotherms and heat flow lines. SCHEMATIC: ASSUMPTIONS: (1) Steady-state conditions, (2) Soil is a homogeneous medium with constant properties. PROPERTIES: Table A-3, Soil (300K): k = 0.52 W/m⋅K. ANALYSIS: (a) From an energy balance on the container, q = E g and from the first entry in T able 4.1, q 2 D k T ( 1 2 ) l D/4z T . π = − − Hence, − − T T q 1 D/4z 20 C+ 500W 1 2m/40m W 92.7 C k 2 D 0.52 2 2m D D = + = = 1 2 ( ) π π m ⋅ K (b) The isotherms may be viewed as spherical surfaces whose center moves downward with increasing radius. The surface of the soil is an isotherm for which the center is at z = ∞.
- 5. PROBLEM 4.25 KNOWN: Igloo constructed in hemispheric shape sits on ice cap; igloo wall thickness and inside/outside convection coefficients (hi, ho) are prescribed. FIND: (a) Inside air temperature T ∞,i when outside air temperature is T ∞,o = -40°C assuming occupants provide 320 W within igloo, (b) Perform parameter sensitivity analysis to determine which variables have significant effect on T i. SCHEMATIC: ASSUMPTIONS: (1) Steady-state conditions, (2) Convection coefficient is the same on floor and ceiling of igloo, (3) Floor and ceiling are at uniform temperatures, (4) Floor-ice cap resembles disk on semi-infinite medium, (5) One-dimensional conduction through igloo walls. PROPERTIES: Ice and compacted snow (given): k = 0.15 W/m⋅K. ANALYSIS: (a) The thermal circuit representing the heat loss from the igloo to the outside air and through the floor to the ice cap is shown above. The heat loss is T T T T ∞ − ∞ ∞ − ,i ,o ,i ic = + cv,c wall cv,o cv,f cap q R + R + R R + R . 2 2 Convection, ceiling: ( ) ( ) cv,c 2 2 2 R = = = 0.00819K W h 4π r 6W m K 4π 1.8m i i ⋅ × 2 2 Convection, outside: ( ) ( ) cv,o 2 2 2 R = = = 0.00201K W h 4π r 15W m K 4π 2.3m o o ⋅ × 1 1 Convection, floor: ( ) ( ) cv,f 2 2 2 R = = = 0.01637K W h π r 6W m K π 1.8m i i ⋅ × Conduction, wall: wall ⎡ 1 ⎛ 1 1 ⎞⎤ ⎡ 1 ⎛ 1 1 ⎞ ⎤ ⎢ ⎜ ⎟⎥ ⎢ ⎜ ⎟ ⎣ ⎝ ⎠⎦ ⎣ ⎝ ⎠ ⎥ ⎦ R = 2 − = 2 − m = 0.1281K W 4π k r r 4π 0.15W m K 1.8 2.3 i o × ⋅ Conduction, ice cap: cap 1 1 1 R = = = = 0.9259K W kS 4kr 4 0.15W m K 1.8m i × ⋅ × where S was determined from the shape factor of Table 4.1. Hence, D D ( ) T ∞ ,i − − 40 C T ∞ ,i − − 20 C = = + ( ) ( ) ( ) q 320W 0.00819 + 0.1281 + 0.00201 K W 0.01637 + 0.9259 K W 320 W = 7.231(T∞,i + 40) + 1.06(T∞,i + 20) T∞,i = 1.2°C. Continued...
- 6. PROBLEM 4.25 (Cont.) (b) Begin the parameter sensitivity analysis to determine important variables which have a significant influence on the inside air temperature by examining the thermal resistances associated with the processes present in the system and represented by the network. Process Symbols Value (K/W) Convection, outside Rcv,o R21 0.0020 Conduction, wall Rwall R32 0.1281 Convection, ceiling Rcv,c R43 0.0082 Convection, floor Rcv,f R54 0.0164 Conduction, ice cap Rcap R65 0.9259 It follows that the convection resistances are negligible relative to the conduction resistance across the igloo wall. As such, only changes to the wall thickness will have an appreciable effect on the inside air temperature relative to the outside ambient air conditions. We don’t want to make the igloo walls thinner and thereby allow the air temperature to dip below freezing for the prescribed environmental conditions. Using the IHT Thermal Resistance Network Model, we used the circuit builder to construct the network and perform the energy balances to obtain the inside air temperature as a function of the outside convection coefficient for selected increased thicknesses of the wall. 0 20 40 60 80 100 Outside coefficient, ho (W/m^2.K) 25 20 15 10 5 0 Air temperature, Tinfi (C) Wall thickness, (ro-ri) = 0.5 m (ro-ri) = 0.75 m (ro-ri) = 1.0 m COMMENTS: (1) From the plot, we can see that the influence of the outside air velocity which controls the outside convection coefficient ho is negligible. (2) The thickness of the igloo wall is the dominant thermal resistance controlling the inside air temperature.
- 7. PROBLEM 4.45 KNOWN: Steady-state temperatures (K) at three nodes of a long rectangular bar. FIND: (a) Temperatures at remaining nodes and (b) heat transfer per unit length from the bar using nodal temperatures; compare with result calculated using knowledge of q. SCHEMATIC: ASSUMPTIONS: (1) Steady-state, 2-D conduction, (2) Constant properties. ANALYSIS: (a) The finite-difference equations for the nodes (1,2,3,A,B,C) can be written by inspection using Eq. 4.35 and recognizing that the adiabatic boundary can be represented by a symmetry plane. 2 7 3 ( )2 q x 5 10 W/m 0.005m T 4T q x / k 0 and 62.5K. Σ 2 ⋅ Node A (to find T2): 2 − + Δ = = = neighbors i Δ × k 20 W/m K 2T2 + 2TB − 4TA + qΔx / k = 0 2 ( ) T 1 2 374.6 4 398.0 62.5 K 390.2K 2 =− × + × − = Node 3 (to find T3): 2 Tc + T2 + TB + 300K − 4T3 + qΔx / k = 0 3 ( ) T 1 348.5 390.2 374.6 300 62.5 K 369.0K 4 = + + + + = Node 1 (to find T1): 2 300 + 2TC + T2 − 4T1 + qΔx / k = 0 1 ( ) T 1 300 2 348.5 390.2 62.5 362.4K = + × + + = 4 (b) The heat rate out of the bar is determined by calculating the heat rate out of each control volume around the 300 K nodes. Consider the node in the upper left-hand corner; from an energy balance E in − E out + E g = 0 or q′a = q′a,in + E g where E g = qV. Hence, for the entire bar q′bar = q′a + q′b + q′c + q′d + q′e + q′f , or ⎡ ⎡ ⎤⎤ ⎡ ⎡ ⎤⎤ ⎡ ⎡ ⎤ ⎣⎢ ⎢⎣ ⎥⎦⎦⎥ ⎣⎢ ⎢⎣ ⎥⎦⎦⎥ ⎣⎢ ⎢⎣ ⎥⎦ ⎤⎥⎦ ′ Δ − Δ Δ − Δ Δ Δ = + ⋅ + Δ + ⋅ Δ + ⋅ + q k q ky q y q bar y T 300 x y T 300 x x y 1 C 2 Δ x 2 2 Δ x 2 2 2 a b ⎡ T C − 300 ⎡ Δ y ⎤⎤ ⎡ T k Δ x + q Δ x ⋅ + k Δ x 3 − 300 + q ⎡ Δ y ⎤⎤ ⎡ Δ x T B − 300 x y ⎢⎣ ⎢⎣ ⎥⎦⎥⎦ ⎢⎣ ⎢⎣ Δ x ⋅ ⎥⎦⎥⎦ + ⎢⎣ k + q ⎡ ⋅ ⎤ Δ y 2 Δ y 2 2 Δ y ⎢⎣ 2 2 ⎥⎦ d e f . c Δ Δ ⎤ ⎦ ⎥ Substituting numerical values, find q′bar = 7,502.5 W/m. From an overall energy balance on the bar, q′ = E ′g = qV/A = q 3Δx ⋅ 2Δy = 5×10 7 W/m 3 ×6 0.005m 2 = 7,500 W/m. ( ) ( ) bar As expected, the results of the two methods agree. Why must that be?
- 8. Problem 1. This problem can be simplified by recognizing that the geometry can be split not just into thirds, but into sixths: Recognizing that no heat is transferred across the “cut” sides (left and lower right), heat flow lines can be drawn roughly in the direction of the arc, making sure that they contact perpendicular to the adiabatic “cut” lines. The inner and outer edges of the geometry are isothermal, so additional isotherms can be drawn between these, making sure cross the heat flow lines perpendicularly. The result should look something like that below: