Cutting tool tech
- 2. 1. 2. 3. 4. Tool Life Tool Materials Tool Geometry Cutting Fluids
- 3. Two principal aspects: 1. Tool material 2. Tool geometry
- 4. 1. Fracture failure ◦ 1. Temperature failure ◦ 1. Cutting force becomes excessive and/or dynamic, leading to brittle fracture Cutting temperature is too high for the tool material Gradual wear ◦ Gradual wearing of the cutting tool
- 5. Fracture and temperature failures are premature failures Gradual wear is preferred because it leads to the longest possible use of the tool Gradual wear occurs at two locations on a tool: ◦ Crater wear – occurs on top rake face ◦ Flank wear – occurs on flank (side of tool)
- 6. Tool Wear Diagram of worn cutting tool, showing the principal locations and types of wear that occur.
- 7. Crater wear, (above), and flank wear (right) on a cemented carbide tool, as seen through a toolmaker's microscope
- 8. Tool Wear vs. Time Tool wear as a function of cutting time. Flank wear (FW) is used here as the measure of tool wear. Crater wear follows a similar growth curve.
- 9. Effect of Cutting Speed Effect of cutting speed on tool flank wear (FW) for three cutting speeds, using a tool life criterion of 0.50 mm flank wear.
- 10. Tool Life vs. Cutting Speed Natural log‑log plot of cutting speed vs tool life.
- 11. vT = C n Relationship is credited to F. W. Taylor where v = cutting speed; T = tool life; and n and C are parameters that depend on feed, depth of cut, work material, tooling material, and the tool life criterion used n is the slope of the plot C is the intercept on the speed axis at one minute tool life
- 12. 1. 2. 3. 4. 5. 6. 7. 8. 9. Complete failure of cutting edge Visual inspection of flank wear (or crater wear) by the machine operator Fingernail test across cutting edge Changes in sound emitted from operation Chips become ribbon-like, stringy, and difficult to dispose off Degradation of surface finish Increased power Workpiece count Cumulative cutting time
- 13. Tool failure modes identify the important properties that a tool material should possess: ◦ Toughness ‑ to avoid fracture failure ◦ Hot hardness ‑ ability to retain hardness at high temperatures ◦ Wear resistance ‑ hardness is the most important property to resist abrasion
- 14. Tool Tip Temperatute vs Cutting Speed 900 600 300 200 400 600 Ft/Min
- 15. Hot Hardness Typical hot hardness relationships for selected tool materials. Plain carbon steel shows a rapid loss of hardness as temperature increases. High speed steel is substantially better, while cemented carbides and ceramics are significantly harder at elevated temperatures.
- 16. Tool material High speed steel: Non-steel work Steel work Cemented carbide Non-steel work Steel work Ceramic Steel work n C (m/min) C (ft/min) 0.125 0.125 120 70 350 200 0.25 0.25 900 500 2700 1500 0.6 3000 10,000
- 17. Highly alloyed tool steel capable of maintaining hardness at elevated temperatures better than high carbon and low alloy steels • One of the most important cutting tool materials • Especially suited to applications involving complicated tool geometries, such as drills, taps, milling cutters, and broaches • Two basic types (AISI) 1. Tungsten‑type, designated T‑ grades 2. Molybdenum‑type, designated M‑grades
- 18. Typical alloying ingredients: ◦ ◦ ◦ ◦ Tungsten and/or Molybdenum Chromium and Vanadium Carbon, of course Cobalt in some grades Typical composition (Grade T1): ◦ 18% W, 4% Cr, 1% V, and 0.9% C
- 19. Class of hard tool material based on tungsten carbide (WC) using powder metallurgy techniques with cobalt (Co) as the binder Two basic types: 1. Non‑steel cutting grades - only WC‑Co 2. Steel cutting grades - TiC and TaC added to WC‑Co
- 20. • • • • • • • High compressive strength but low‑to‑moderate tensile strength High hardness (90 to 95 HRc) Good hot hardness Good wear resistance High thermal conductivity High elastic modulus ‑ 600 x 103 MPa Toughness lower than high speed steel
- 21. Used for nonferrous metals and gray cast iron Properties determined by grain size and cobalt content ◦ As grain size increases, hardness and hot hardness decrease, but toughness increases ◦ As cobalt content increases, toughness improves at the expense of hardness and wear resistance
- 22. Used for low carbon, stainless, and other alloy steels TiC and/or TaC are substituted for some of the WC Composition increases crater wear resistance for steel cutting ◦ But adversely affects flank wear resistance for non‑steel cutting applications
- 23. Combinations of TiC, TiN, and titanium carbonitride (TiCN), with nickel and/or molybdenum as binders. • Some chemistries are more complex • Applications: high speed finishing and semifinishing of steels, stainless steels, and cast irons – Higher speeds and lower feeds than steel‑cutting carbide grades – Better finish achieved, often eliminating need for grinding
- 24. Cemented carbide insert coated with one or more thin layers of wear resistant materials, such as TiC, TiN, and/or Al 2 O 3 • • • • Coating applied by chemical vapor deposition or physical vapor deposition Coating thickness = 2.5 ‑ 13 µm (0.0001 to 0.0005 in) Applications: cast irons and steels in turning and milling operations Best applied at high speeds where dynamic force and thermal shock are minimal
- 25. Photomicrograph of cross section of multiple coatings on cemented carbide tool
- 26. Primarily fine‑grained Al2O3, pressed and sintered at high pressures and temperatures into insert form with no binder • Applications: high speed turning of cast iron and steel • Not recommended for heavy interrupted cuts (e.g. rough milling) due to low toughness • Al2O3 also widely used as an abrasive in grinding
- 27. Sintered polycrystalline diamond (SPD) fabricated by sintering very fine‑grained diamond crystals under high temperatures and pressures into desired shape with little or no binder • Usually applied as coating (0.5 mm thick) on WC-Co insert • Applications: high speed machining of nonferrous metals and abrasive nonmetals such as fiberglass, graphite, and wood – Not for steel cutting
- 28. Next to diamond, cubic boron nitride (CBN) is hardest material known Fabrication into cutting tool inserts same as SPD: coatings on WC‑Co inserts Applications: machining steel and nickel‑based alloys SPD and CBN tools are expensive
- 29. Two categories: Single point tools ◦ Used for turning, boring, shaping, and planing Multiple cutting edge tools ◦ Used for drilling, reaming, tapping, milling, broaching, and sawing
- 31. The "business end" of a twist drill has two cutting edges The included angle of the point on a conventional twist drill is 118° Margins are the outside tip of the flutes and are always ground to the drill diameter
- 32. • • An essential feature of drilling is the variation in cutting speed along the cutting edge. The speed is maximum at the periphery, which generates the cylindrical surface, and approaches zero near the center-line of the drill where the cutting edge is blended to a chisel shape. Drills are slender, highly stressed tools, the flutes of which have to be carefully designed to permit chip flow while maintaining adequate strength.
- 33. Chip removal ◦ Flutes must provide sufficient clearance to allow chips to be extracted from bottom of hole during the cutting operation Friction makes matters worse ◦ Rubbing between outside diameter of drill bit and newly formed hole ◦ Delivery of cutting fluid to drill point to reduce friction and heat is difficult because chips are flowing in opposite direction
- 34. Any liquid or gas applied directly to machining operation to improve cutting performance Two main problems addressed by cutting fluids: 1. Heat generation at shear and friction zones 2. Friction at tool‑chip and tool‑work interfaces Other functions and benefits: ◦ Wash away chips (e.g., grinding and milling) ◦ Reduce temperature of workpart for easier handling ◦ Improve dimensional stability of workpart
- 35. Cutting fluids can be classified according to function: Coolants - designed to reduce effects of heat in machining Lubricants - designed to reduce tool‑chip and tool‑work friction
- 36. Water used as base in coolant‑type cutting fluids Most effective at high cutting speeds where heat generation and high temperatures are problems Most effective on tool materials that are most susceptible to temperature failures (e.g., HSS)
- 37. Usually oil‑based fluids Most effective at lower cutting speeds Also reduce temperature in the operation
- 38. No cutting fluid is used Avoids problems of cutting fluid contamination, disposal, and filtration Problems with dry machining: ◦ Overheating of tool ◦ Operating at lower cutting speeds and production rates to prolong tool life ◦ Absence of chip removal benefits of cutting fluids in grinding and milling
- 39. Gear cutting is the process of creating a gear. The most common processes include hobbing , broaching, and machining; other processes include shaping, forging, extruding, casting, and powder metallurgy. Hobbing is a machining process for making gears, on a hobbing machine, The teeth or splines are progressively cut into the workpiece by a series of cuts made by a cutting tool called a hob . Compared to other gear forming processes it is relatively inexpensive but still quite accurate, thus it is used for a broad range of parts and quantities
- 41. • • • The two shafts are rotated at a proportional ratio, which determines the number of teeth on the blank; for example, if the gear ratio is 40:1 the hob rotates 40 times to each turn of the blank The hob is then fed up into workpiece until the correct tooth depth is obtained. Finally the hob is fed into the workpiece parallel to the blank's axis of rotation
- 42. Hobbing uses a hobbing machine with two non-parallel spindles, one mounted with a blank workpiece and the other with the hob. The angle between the hob's spindle and the workpiece's spindle varies, depending on the type of product being produced. If a spur gear is being produced, then the hob is angled equal to the helix angle of the hob; if a helical gear is being produced then the angle must be increased by the same amount as the helix angle of the helical gear
- 43. • • • The hob is the cutter used to cut the teeth into the workpiece. It is cylindrical in shape with helical cutting teeth. These teeth have grooves that run the length of the hob, which aid in cutting and chip removal. The cross-sectional shape of the hob teeth are almost the same shape as teeth of a rack gear that would be used with the finished product
Editor's Notes
- #25: Physical vapor deposition (PVD) is a variety of vacuum deposition and is a general term used to describe any of a variety of methods to deposit thin films by the condensation of a vaporized form of the material onto various surfaces (e.g., onto semiconductor wafers). The coating method involves purely physical processes such as high temperature vacuum evaporation or plasma sputter bombardment In a typical CVD (Chemical vapor deposition) process, the wafer (substrate) is exposed to one or more volatile precursors, which react and/or decompose on the substrate surface to produce the desired deposit
- #27: Sintered -> Formed into a mass by heat and pressure
- #28: Diamond succumbs to graphitization, which means that it will change its crystal structure to graphite crystal structure at 250C in the presence of a catalyst metal such as carbon steel
- #31: Back rake angle (BR) is the angle between the cutting face of the tool and the shank, measured parallel to the side of the shank. The angle is positive if, as shown in Fig. 7, it slopes from the cutting point downward toward the shank, and negative if it slopes upward toward the shank Side rake angle (SR) is the angle between the cutting face of the tool and the shank, measured perpendicular to the side of the shank. The angle is positive if, as shown in Fig. 7(c), it slopes downward away from the cutting edge to the opposite side of the shank, and negative if it slopes upward. Front Clearance angle is the angle between the flank face of the tool and a line drawn from the cutting edge perpendicular to the base of the shank. Side clearance angle is the angle between the side flank immediately below the side cutting edge and a line drawn through the side cutting edge perpendicular to the base of the tool End cutting-edge angle (ECEA) is the angle between the end cutting edge of the tool and a line perpendicular to the side of the shank. Side cutting-edge angle (SCEA), also called lead angle, is the angle between the side cutting edge and the projected side of the shank. Nose radius (NR) is the radius on the tool between the end and the side cutting edges
- #32: Drill is called Twist Drill because it cuts because of twisting action. The rake angle being controlled by the helix angle of the drill For a drill to bore true and on location it is absolutely imperative that the margin and the point be ground concentric and be on center The land is the portion relieved from the margin. Without this relief there would be a great deal of friction created during the drilling process As the lips are being formed in the sharpening process to the desired angle at the very tip the "chisel point," is formed. General purpose drills normally have the chisel point. The big disadvantage here is that this point does not penetrate well at the start and has a tendency to wobble. To eliminate this wobble a center drill (below) is used to start the hole or a drill bushing to guide the drill
- #37: Coolants possess low viscosity as compared to lubricants
- #40: 2. … Hobbing machine is a special type of milling machine.
- #42: 1. … Note that the previous example only holds true for a single threaded hob; if the hob has multiple threads then the speed ratio must be multiplied by the number of threads on the hob.
- #44: There are slight changes to the shape for generating purposes, such as extending the hob's tooth length to create a clearance in the gear's roots