Design & Analysis of foldable E-Bicycle

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 09 Issue: 06 | Jun 2022 www.irjet.net p-ISSN: 2395-0072
© 2022, IRJET | Impact Factor value: 7.529 | ISO 9001:2008 Certified Journal | Page 2928
Design & Analysis of foldable E-Bicycle
Pratiksha Dorugade1, Prafful Jadhav2, Prathmesh Kolhe3, Hemant Mane4 , Umesh Sangle5,
Kamlesh Pardeshi6
1234Student, Department of Mechanical Engineering, Shivajirao S. Jondhale College of Engineering Sonarpada,
Dombivli, Maharashtra, India.
56Freelancer, Bachelor in Mechanical Engineering, Kalyan, Maharashtra, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - The aim of this paper is to present the detailed
report of the project titled as Design and analysis of foldable
electric bicycle chassis. The paper tries to cover all the
prominent aspects of the project work i.e. ‘market research’,
‘literature review’, ‘design’, ‘analysis’, ‘observations’, and
‘rectifications’, etc. The electric bicycle, as a new mode of
private transportation, has ushered in a new era of mobility,
although electric bicycle research is very young, no one
understands where the efforts are now focused or what the
scientific community's primary topics of interest are. Because
they are ecologically friendly, require less maintenance,
produce less motor output noise, and are more efficient. The
primary purpose of an E-Bike is to reduce and eliminate
pollution. Rather than using a typical car. An E-bike combines
the advantages of both a bicycle and amotorcycle. Meanwhile,
a high-priority demand for urban bicycles is their availability
in small sizes, which may be addressed by including a feature
in their design that allows them to be folded into portable
sizes. In other words, by reducing their capacity, bicycles may
be transported on trains, buses, or any other method of public
transit, as well as kept in small residential and office spaces.
The installation of a pivot in the frame permits folding of a
bicycle; the frame may then be folded around the pivot,
decreasing the bicycle's size. As a result, we feel that our
design must meet this need.
Key Words: E-bike, foldable E-bike, Eco-friendly
transportation, design and development, etc.
1. INTRODUCTION
In the present era, humans aren't ready to dedicate specific
time to their health. To deal with this deficit we will go
cycling daily which can eventually help us mitigate the
surplus amount of fats and calories which can lead us to a
healthy lifestyle. Transportation on the opposite hand has
significantly risen and therefore the amount of excess CO2
released into the air has resulted in heating. The world
accounts for 1/3rd of the carbon emission within the
atmosphere. The high rise in fuel prices is additionally a
serious concern for the common man’s life and this will be
alternated by different modes of transport available within
the market. Consistent with a report, short trips by car
contribute disproportionately to transportation emissions.
Europe contributes about 30% of trips with cars covering
distances but three kilometres. Many countries within the
world have given substantial emphasis to the promotion of
active travel with a series of reports from the govt.andother
private bodies making the case for people to steer or cycle
for brief journeys. Cycling is that the preferred mode of
transport for brief distances whichisadditionallyanefficient
mode of transportation that emits a really less amount of
carbon footprint. Cycling is a cheap mode of transport with
very low maintenance. Bicycles were introduced within the
late 19th century in Europe, and by the first 21st century,
quite 1 billion were alive at a given time. From the start and
still today, bicycles are and are employed for several uses.
The folding bicycle still is considered new technology.
Generally, folding bicycle or folder may be a sort of bicycle
that comes with hinges or joints within the frame and
handlebar stem that let it to be weakened into a more
compact. the primary folding bicycle known for the primary
patent was originated some time past in 1939 from A.J.
Marcelin by the name of “Le Petit Bi”, a 16-inch wheeled
folding bicycle. To date, enormous amount of manufacturer
has begun with their own folder design that suit everybody
needs also on compete in market domination. However,
there are still more scopes for improvement mostly in term
of fabric and functional design. This is often thanks to the
frame that creates the folding bike susceptible to stresses
and weakness within the overall structure.Thebigvariety of
folding bicycles reflects the various methods to permit a
bicycle to fold. The only folding frameshaveonehingewhich
allows the bicycle to easily fold approximately in half.
Bicycles built on this pattern usually even have quick-
connect clamps to permit raising and lowering the steering
and seat columns quickly. E-foldable Bicycleisessentiallyan
environmentally friendly and economical mode of private
transportation powered by human force also as electrical
power, and therefore the use of bicycles as a mode of
transportation is that the most promising step toward
developing green transportation.
There are many situationswherepeoplecouldchoosetoride
a bicycle, whether it is to go to school, to a job, to meet with
friends, or just for recreational purposes. However, once
people reach their destination and have a break between
their trips, they are left with a bicycle with little means of
storing it while they go about their day. Some people buy a
bike lock so that they can secure it in a safe location, while

others may just lean it against a wall or even roll it into the
building with them. Traveling is also expensive already, and
for those who travel so much may wish to take the bicycle
with them and not want to rent an expensive vehicle when
they reach their destination. The motivation for this project
is to come up with a solution so that the bicycleiselectrically
powered but also compact andsmall sothatpeoplecanbring
the bicycle on a journey as carry-on, and not be an
inconvenience with the bicycle weight and size.
2. DESIGN CONSTRAINTS
2.1 Design Optimisation
To design a product which is compact in size with enhanced
ergonomic and aesthetic constraints and characteristics
which are better than the typical product available in the
market. To design an e-bicycle which is foldable, thereby
easy to carry (can be fitted in a bag), light in weight with
same strength, durability and loadcarryingcapacityasofthe
mass produced bicycles available in the market along with
an increased power harnessing efficiency from the motor.
2.2 Material Optimisation
To analyse the 3D model for different materials by
conducting various tests like structural (stresses, bending,
impact, etc.), thermal, etc.; to decide the best material to be
used for manufacturing of the product.
Table -1: Advantages & disadvantages of E-Bicycle.
Conventional Bicycle Foldable E-Bicycle
Advantage Disadvantage Advantage Disadvantage
Cheaper
Low
performance
& Heavier
Better
performan
ce
Expensive
Strong &
Rigid
single
piece
pattern
Bulky and
basic
structure
Compact &
foldable
Less rigid
structure due
to 2 piece
pattern
More
Stable
Less Secured
Easy to
carry &
Secured
Less Stable
3. COMPONENTS
3.1 Bicycle Frame
It is a backbone of every automobile. The entire component
is mounted in it. We are using frame with more rigidity and
for better space management. We are considering two
materials for the frame design. (a) Alloy(6061)FoldingType
Frame. (b) Ultra-High Tensile Steel Frame Folding Type
F
Fig -1: Foldable Bicycle Frame-Unfolded
Fig -2: Foldable Bicycle Frame-Folded
Considering the overall DVP parameters associatedwiththe
product and considering the weight to strength ratio we can
conclude that Aluminium has some significant pros over the
steel frame. As it was mentionedaboveindesignparameters,
weight consideration was the main objective. It was
necessary to opt the material which could bear the forces
induced during the motion as well be light. Considering all
the above factors, it has been decided to use ALUMINIUM
6061 ALLOY seems to be the most viable material for the
component. The strength on weightratioissufficienttomeet
our standards.
Table -2: Material Comparison
Parameters Aluminium 6061 Steel 4130
Total mass 7335.11 grams 11764.46 grams
Density 2.7 g/cm3 7.85 g/cm3
Volume 2342293.33 mm3 2342293.33 mm3

Material Cost 350 per kg 150 per kg
Machinability Easy to machine
Little hard to
machine
Weldability
Can weld to similar
metal
Can weld any
material
Yield Strength 276 MPa 460 MPa
Tensile
strength
310 MPa 560 MPa
Extra
comments
/Observation
1. Easy to
fabricate parts.
2. Material is
sufficient to
sustain the
loads.
3. Cannot
carrode.
4. SAE INDIA and
major other
industrial
standard
refers the
material for
cycle
manufacturing
.
5. Weight is
much less
compare to
steel.
1. Easy to
manufacture
parts but
weight and
surface finish
will differ.
2. Can corrode.
3. SAE INDIA and
major other
industrial
standard
refers the
material for
cycle
manufacturing.
4. Weight is
much higher
so little affects
the portability.
3.2 Rear Hub Motor
Hub motor is machine that converts electric power in
mechanical power output. The motor output is rotational
motion to the shaft and the input is to be direct current
supply. In a hub motor the spinning rotor has an axle
running through the middle that is used to drive the
machine. Rear hub motors provide propulsion and
assistance by spinning the back tire. The circuit switchesthe
power on and off in the coils which creates forces in each
one that make the motor spin. The brushes press against the
axle of a normal motor which in turn introduce friction,
slows it down and releases certain amount of noise and
waste energy. They push the rider forward, thereby
providing the extra power on demand. They are usually
brushless motors which replace the commutator with half a
dozen coils and an electric circuit. They are often more
efficient at low speeds. The rear hub motor is the most
common form of an e-bicycle motor placement in the
market. We are using BLDC 36V/250W, 40 Nm Rear Hub
Motor.
3.3 Integrated Batteries
Battery is an electrochemical devicethatstoresenergyinthe
form of chemical energy. When the battery us connectedtoa
circuit due to the flow of electrons it generates electric
energy. The electrolyte is used as an electron transportation
medium between the anode and cathode. Integrated
batteries on electric bicycles are placed inside the frame of
the bicycle cannot be seen outside. Batteriesareoftwotypes
that are primary and secondary. The Primary batteries are
for one-time use and are non-rechargeable. The Secondary
batteries are reusable and can be recharged and used
frequently. Lead acid batteries and Lithium-ionbatteries are
the most common used in the industry as they are efficient
and cheap. Placement of these integrated batteries are most
commonly found inside the bottom tubeoftheframe. We are
using 36V, 5.8Ah Li-Ion (IP65/67 protection) Battery.
Mass = 2633.86 grams (approx.)
3.3 Transmission
A Transmission system is the one which transmit the power
developed by the motor to the driving wheel of the Bicycle.
In chain Transmission the movement is transmitted by
winding and engaging the chain wheel mounted on shafts. It
is used to avoid slipping and transmit large forces making
the gearshifts to drive the chain on sheets and pinion. In
Bicycle the transmission does not transmit constant torque.
In bicycle chain drive hasmaintainedtheadvantage between
the drive and driven sprockets to achieve maximum speed.
The crank set is the component that converts the
reciprocating motion into rotational motionwhichisused to
drive the chain. It consists of one or moresprocketsattached
to the cranks to which the pedals are attached. We are using
Single - Speed Bicycle Chain - 12.7mmx3.175mm
Crankset - 40T
3.4 Brakes
Brake is the most important because by the help it, we can
stop the vehicle. There are many types of brakes are present
in the market but we are using the most suitable brake.
Brakes used to slow down as kinetic energy (motion) is
transformed into thermal energy (heat). There are different
types of brakes however, the most commonusedarecalliper
brakes, cantilever brakes, V-Brakes and disc brakes. Disc
brakes are more powerful and require less strength to
operate. They require a compatible hub, wheel rim, and
frame. There are two types of disc brakes they are Hydraulic
or mechanical cable pull. They are great for fast application
on Off-Road roads. Disc brakes can handle high heat and do
not damage tyre by heating the rim like the rim-brakes do.
Disc brakes are durable and high in strength hence; they are
used on rough tracks. V-Brakes are also called as linear-pull
or direct-pull brakes. They are extremely powerful and are
commonly used in off-road bikes & mountain bikes. This
breaks are little heavier than the cantilever brakes and can
work on rough terrain. They have the power to stop on wet
or muddy terrain and are more durable than the cantilever
brakes. We are using Mechanical Disc Brake at the front
and a V-Brake at the rear.

3.5 Wheel & Tires
A bicycle wheel is mostly wired frame which supports the
tyre and frame of the bicycle. A bicycle wheel consists of
several sub-parts like hub, Axle, Bearings, rims and spokes.
Tubeless tires are used on mountain bikes due to its low air
pressure which gives a better traction. We are using a pair
of 27.5" x 1.95" tires with Double Wall Alloy Rims.
3.6 Suspension
Bicycle suspensions are used to insulate the bikefromrough
terrain. The suspension geometry is design such that it
comforts the driver’s ride over any terrain maintaining the
good ride height. Being an off road bicycle it is suitable to
have a long travel suspension that could easily bounce and
rebound with minimum shock transfer to the rider & also
help to negotiate sharp corners comfortably. They are
primarily used in mountain bikes and off road bikes. Infront
telescopic suspension is used because of durability,strength
and handling characteristics. In a bike it has 1 or 2 shock
absorbers which are designed to mitigate the impact of
rough terrain by compressing and rebounding. Most
mountain bike forks will feature during aspectslikea degree
of adjustability, firm to plush as well as adjustability in the
travel amount. It is based around a spring and a damper and
on the lower end or on the occasional gravity focused fork, a
metal coil spring. We are using Steel Rigid Aerodynamic
Fork Rigid suspension
Fig -3: Suspension and Wheel System.
3.9 Electrical Subsystem Assembly
As it was mentioned above in design parameters, for the
electrical assistance to support with motor assist and the
maximum terrain conditions we have decided to use
Battery: 36V, 5.8Ah Li-Ion (IP65/67 protection) (Mass =
2633.86 grams), Motor: BLDC 36V/250W, 40 Nm, PCB
Controller (Mass = 153.39 grams).
Fig -4: Electrical Subsystem Assembly.
4. DESIGN TESTING AND ANALYSIS
Fig -5: Stress, strain and deformation analysis under
static load conditions for main frame.
4.1 Frame Analysis
Material: Aluminium 6061
Density: 2.7 g/cm3
Maximum Tensile Strength: 310 MPa=3.1e+8 N/sq. m.
Maximum Yield Strength: 276 MPa=2.76e+8 N/sq. m.
Maximum Stress: 1.389e+7 N/sq. m. (which is much less
compare to allowable material strength)
Maximum Total Deformation: 1.329e-10mm(whichismuch
less for practical considerations)
Maximum strain: 1.516e-4
Maximum force applied:Due toweightconsiderationofrider
as 70 kg.

Material: Steel 4130 alloy
Density: 7.85 g/cm3
Maximum Total Deformation: 1.326e-5 mm (which is much
Maximum strain: 1.81e-6
Maximum force applied:Due toweightconsiderationofrider
as 70 kg.
Factor of safety: FOS > 1
Fig -6: Stress, strain and deformation analysis under
static load conditions for rear frame.
4.2 Hinge Analysis
Material: Mild steel
Density: 8 g/cm3
Maximum Total Deformation: 7.798e-5 mm (which is much
Fig -7 left: direction of actual load consideration to justify
the strength of axle used in hinge. (OEM part capable of
handling standard cycle load and variation).
Fig -7 right: Deformation concentration zone.
Fig -7: Deformation concentration zone for hinge.
5. CONCLUSIONS
This study aimed to understand the convenience of using
foldable E-bicycles as a mode of transportation in modern
cities. In this study, we proposed that the design of the
folding mechanism of bicycles should be considered from
three aspects. First, the advantage of foldable bicyclesisthat
the greater the number of pivots, the smaller is the bicycle
size after folding. On the other hand, if the number of pivots
is small, the hand movement is shortened and the
performance time is reduced. Therefore, folding usability is
improved. Due to its high strength andcompactsizeitisvery
easy to park it inside the office, home, public places etc. Due
to its efficient and green electric drive we can ride this
bicycle to a great distance and it also help us to move one
step toward the use of green energy.
REFERENCES
[1] Shishir S, Manjunath P, Pavanasudan R, Ravi Sathyajith
(2015),” Design and Fabrication of Foldable Bicycle”,
SSRG International Journal of Mechanical Engineering (
SSRG– IJME ), Volume 2, Issue 6, June 2015M. Young,
The Technical Writer’s Handbook. Mill Valley, CA:
University Science, 1989.
[2] Vishal Saptarshi1, Ravi Vishwakarma, Pawan Sharma,
Prafull Baraskar (2020),” Designing and Constructionof
E- Foldable Bicycle”, International Research Journal of
Engineering and Technology (IRJET), Volume 07, Issue:
12, Dec 2020
[3] Prof. Mayur Shelke1, Abhinav Tingne, Sajal Chandrakar,
Prathamesh Bharti, Vishal Meshram, Tejas Dahikar
(2018),”Design Methodology to Fabricate Foldable
Bicycle”, International Journal for Research in Applied
Science & Engineering Technology(IJRASET),Volume6,
Issue III, March 2018
[4] Arunachalam M., Arun Prakash R. and Rajesh R.(2014)
,”FOLDABLE BICYCLE: EVALUATION OF EXISTING

DESIGN AND NOVEL DESIGN PROPOSALS”, ARPN
Journal of Engineering and Applied Sciences,VOL.9,NO.
5, MAY 2014
[5] Esther Salmeron-Manzano and Francisco Manzano-
Agugliaro.(2018) ,” The Electric Bicycle: Worldwide
Research Trends”, ENERGIES Review, Received:26May
2018; Accepted: 18 July 2018; Published: 20 July 2018

Design & Analysis of foldable E-Bicycle

More Related Content

What's hot (20)

Similar to Design & Analysis of foldable E-Bicycle (20)

More from IRJET Journal (20)

Recently uploaded (20)

Design & Analysis of foldable E-Bicycle