Design and Control of a Hydraulic Servo System and Simulation Analysis

International Journal of Modern Research in Engineering & Management (IJMREM)
||Volume|| 1||Issue|| 7 ||Pages|| 29-40 || July 2018|| ISSN: 2581-4540
www.ijmrem.com IJMREM Page 29
Design and Control of a Hydraulic Servo System and Simulation
Analysis
Dechrit Maneetham
Department of Mechatronics Engineering
Rajamangala University of Technology Thanyaburi, Thailand
------------------------------------------------------ABSTRACT----------------------------------------------------
This paper describes the system analysis, modeling and simulation of a Hydraulic Servo System (HSS) for
hydraulic mini press machine. Comparisons among linear output feed back PID control, Fuzzy control and
Hybrid of PID and Fuzzy control are presented. Application of hybrid controller to a nonlinear is investigated
by both position and velocity of the hydraulic servo system. The experiment is based on an 8 bit PIC
16F877 microcontroller, and the simulation is based on MATLAB Simulink. Simulation and hardware
experimental results show that the hybrid controller gave the best performance as it has the smallest overshoot,
oscillation, and setting time.
KEY WORDS: PID and Fuzzy Control, Microcontroller, Hydraulic Servo System, Modeling and Simulation
---------------------------------------------------------------------------------------------------------------------------------------
Date of Submission: Date, 18 July 2018 Date of Accepted: 23 July 2018
---------------------------------------------------------------------------------------------------------------------------------------
I. INTRODUCTION
Nowadays, hydraulic system is widely used in many applications on any field such as transportation, building
construction, factories, until performance art and film industries [21]. Since a hydraulic system is a strong
actuator system, it has to be controlled well to achieve the desired purposes and safety. In many applications of
hydraulic servo system, when linear motion is required, piston control is always the first choice. In simple
application that only require the piston to produce back and forth motions between the two endpoints, the valve
that control the piston simply operate in on/off mode. With the development of advanced technology, a
combination between hydraulic servo system and electronic devices was established to take the full advantages
of them. At the same time, the most common way is to provide the controller in describing the PID control
Fuzzy control and Hybrid control and the control law design is complex to extend to multi-variable system. In
[26], fuzzy control of a hydraulic servo system gives the fasts response characteristic of the system. Fuzzy PI
controller is added in the feed forward branch of the closed loop enhanced by the variable structure controller
[16]. In [9], Fuzzy PD controller has better performance of the control system. The applications of Fuzzy
tracking control has been successfully applied to control hydraulic systems and can get more robustness and
better performance [23]. Most of the performance of PID tuning for processes use frequency response.
Therefore, a wide variety of PID tuning controller has been investigated in Ziegler-Nichhols rule [12]. Optimal
tuning PID is satisfied even in case where the system is dynamics and the system operating are points change
[13]. Moreover, a variety of methods have been developed for modeling and simulation such as modeling and
simulation of physical systems and design as an integrated system [2], [3]. In [8], velocity control of hydraulic
servo system achieves fast response. An alternative approach for complex control with Hybrid of Fuzzy PID
control was developed by [18]. The application of the hydraulic mini press machine has a number of
characteristics complicate the design of fault detection systems. These include highly nonlinear dynamics of the
hydraulic systems such as dead – band and hysteresis existing in the control valve, nonlinear pressure/ flow
relations and variation devices which are commonly used in the die casting and injection molding machines [22].
The cycle in both of these processes involve accurate velocity control, followed by a pressure control phase.
Some of the most significant developments in a hydraulic mini press machine are in the area of electronic
control, specially using microcontroller-based technology. The use of digital and analog control for closing the
actuator position has been established for some time. Also, the control system must be fast acting, as the
processing speed can be several tuning parameters during the performance. The function of the Hybrid
controllers are integrated with PID and Fuzzy control. It can adaptively adjust controller parameters as design of
Hybrid PID Fuzzy controller has a good relation between performance and tune that the PID Fuzzy controller
can obtain good dynamic performance of a hydraulic mini press machine [25]. The purpose of this paper is to
discuss on how to achieve the best control performance of a hydraulic mini press machine. In section 2, the
discussion focuses on dynamic model and on the method used to position control in hydraulic servo systems.

Design and Control of a Hydraulic Servo System…
4
t
L tp L L
e
V
P Ax C P Q

= − − +
Section 3 presents the conceptual design of a Hybrid of Fuzzy PID controller. In section 4, simulations and
experimental results are separated by comparing with PID, Fuzzy and Hybrid control. Finally, the paper is
concluded in Section 5.
II. PROBLEM STATEMENT AND DYNAMIC MODEL
System model of a typical inertial load drive by a hydraulic servo system is shown in Figs.1 and 2. A hydraulic
system was developed by [15]. The system can be thought of as a double acting cylinder driving an inertial load
at the end. The dynamic of the inertial load can be written
Fig. 1: A hydraulic servo valve Fig. 2: Photo of high performance
hydraulic servo valve
(1)
sgn( )s v L
L d v
P x P
Q C wx

−
= (2)
where tV is the total actuator volume 3
( )m , e is the effective bulk modulus 2
( / )N m , LP is the load pressure
( )Pa , A is the actuator ram area 2
( )m , x is the actuator piston position tpC is the total coefficient of
leakage 3
( / . )m s Pa , LQ is the load flow 3
( /sec)m , dC is the discharge coefficient, w is the spool valve area
gradient ( )m , vx is the spool valve position ( )m , sP is the supply pressure ( )Pa , and  is the fluid density
3
( / )kg m . The valve of friction, a double acting hydraulic cylinder drives a mass connected to its rod end in the
horizontal direction. Thus, the load dynamics, we obtain
L fP A mx kx F= + + (3)
where m is the total mass of the actuator, fF is the friction force, A is the actuator ram area, and LP is the load
pressure as 1 2LP P P= − .
Assuming Equation (1), (2), and (3) the mathematical model in the system state equations are
2x x=
2 3
1
( )fx Ax F
m
= −
( )3 2 3 4 3 4sgn( ) )sx x x P x x x = − − + − (4)
4 5x x=
2 2
5 4 52e e ex x x   = − − +
Xv
Xp
cylinder piston load
Ctp
1 1,P Q 2 2,P Q
Supply
port
Return
port
Return
port
RP RPSP

where ( )x is the actuator piston position, 2( )x is the actuator piston velocity, 3( )x is the load pressure, 4( )x is
the valve position, 5( )x is the input current to servo system, ( ): 4 /e tA V  , ( ): 4 /e tp tC V  , and
( ): 4 / 1/e d tC w V   . It can be observed from these results that the system responses to the sinusoidal reference
signal input and output amplitudes. The tracking objective is the amplitudes by comparing with the frequency of
1 Hz and 6 Hz and phase shift. The values of the system are given in Table 1.
Table1. The characteristic values of the hydraulic servo system.
Component Symbol Valve Unit
Supply pressure Ps 5*106
Pa
Total actuator volume Vt 2.44*10-5
m3
Effective bulk modulus βe 7.60*108
N/m2
Actuator ram area A 1.22*104
m2
Actuator piston position Χ 0.2 m
Total leakage coefficient Ctp 5*10-13
m3
/(s.Pa )
Discharge coefficient Cd 0.61 -
Spool valve area gradient w 2.39*10-3
m
Spool valve position (stroke) χv 0.238*10-3
m
Load flow QL 2.5*10-5
m3
/sec
Fluid mass density ρ 870 kg/m3
Mass of actuator and load m 9 kg
III. PID CONTROLLER
PID controllers are so far the most common in industrial process [19]. They have several important functions,
provide feedback, have the ability to eliminate steady state offsets through integral action and can anticipate the
future through derivative action [15]. In practice, PID controllers are used at the lowest level and multivariable
controllers provide set points. The behaviour of a PID algorithm can be described as
1
0
(( )
1
( )
( )
)p
i
d
e t eu t K
T
de t
d T
dt
 
 
 = +
 
 
+
(5)
Where pK is the proportional action, iT is the integral time and dT is the derivative time? The PID controllers
are parameterized by the following transfer function.
( ) ( ) ( )
( ) 1 ( ) ( )
X s C s G s
R s C s G s
=
+
(6)
The closed loop third order is given as
3 2
5432.58
( )
179.65 8069.07
G s
s s s
=
+ +
(7)
Transfer function of Eq. (6) using Eq. (7) yields
1 2
1 2
1
(1 )
(1 )(1 )
1
1 (1 )
(1 )(1 )
p ds
is p s p s
p ds
is p s p s
k
k T
T s T T
k
k T
T s T T
+ +
+ +
+ + +
+ +
(8)
The result acquired under the condition of PID controller are given as 0.694,pk = 1.84ik = and 1.64dk = . The
PID controller was designed by following standard procedure of PID controller design, which consists of control
and plant as shown in Fig. 3.

Fig. 3: PID Control Scheme
PID controller are usually limited due to highly nonlinear behavior of the hydraulic dynamics. More than half of
industrial controllers in use utilized or modified PID control schemes. PID controllers are mostly hydraulic,
pneumatic, electric and electronic types or their combinations. Currently, many of them are based on MATLAB
simulation. Matlab is a widely used, portable and numerically reliable package. Simulink extends Matlab by
adding block diagram of PID control. Matlab sytem identification toolbox software is applied in order to create
the mathematical model of the system. The process modeling tool is selected to customize the structure of the
identified model based on the knowledge of the third order system. The Simulink model of the PID control
system can be shown in Fig. 4.
Fig. 4: The Simulink model of the PID Control system
IV. HYBRID OF PID AND FUZZY CONTROLLER
This research implemented a combination of the two controllers to construct a new characteristic of the system
response. The main idea in PID-Fuzzy controller is to combine the simplicity of the PID controller and the
reliability of the Fuzzy controller [25]. If PID controller is set to be very stiff, it will cause a significant
overshoot or undershoot. In contrary, if it is set to a lower sensitive setting, it will take longer settling time [7].
A Fuzzy controller is chosen in this paper, where the two inputs are the position error and its derivative, or the
velocity error. To model a system in fuzzy logic the response of the system in terms of the input- output must be
known and designer should be aware of how the inputs and outputs are related. Controller output is voltage to
the servo valve. Input and output of interface block are given in Fig. 5. For the complicated system it is difficult
to implement the controller because there are many ways to define the linguistic values and rules. Indeed, it can
be extremely difficult to find a viable set of linguistic values and rules just to maintain stability.
( )R s ( )E s
+
-
1
1P ds
is
K T
T
 
+ + 
 
Plant
( )C s

Fig. 5: Structure of the fuzzy predictor step – interface block
As mentioned the position and the velocity are the inputs to the fuzzy controller. Logic operations are applied,
seven triangular membership function are used in the fuzzification 7*7 fuzzy logic rule matrix. The position
( P = real time position-set position) and velocity ( V = real time velocity-set velocity) difference are
expressed by a number in the interval from -255 to 255 to represent distance from -100 to 100 mm/s. According
to the rules membership function can be given in Fig. 6 and 7, while the control surface is depicted in Fig. 8. It
can be seen from the surface, which stands for the control voltage, it is impossible to realize this kind of control
action for conventional method
Fig. 6: Membership function of the fuzzy Fig. 7: Membership function of the fuzzy
controller for input controller for output
Fig. 8: Control surface of the fuzzy controller
Rule1: If P is VNEG and V is VPOS, the O is ZE
[( P = VNEG  V = VPOS); then O = ZE]
Rule2: If P is VNEG and V is POS, the O is SPOS
[( P = VNEG  V = POS); then O = SPOS]
Rule3: If P is VNEG and V is SPOS, the O is POS
[( P = VNEG  V = SPOS); then O = POS]
The input and output regions are related by a set of rules. Once the fuzzy controller is activated, rule evaluation
is performed and all the rules which are true are fired. So with IF-THEN rule, we can describe the rule of fuzzy
algorithm with the following two dimensional table rules, which are given in Table 1.

1
1
( )
( )
n
j j
j
n
j j
j
z u z
z
z u z
=
=
=


Table 1. Rules matrix for fuzzy controller
Referring to Table 1, where VNEG is very negative; NEG is negative; SNEG is small negative; ZE is zero; SPOS
is small positive; POS is positive; VPOS is very positive. The output valve remain a fuzzy number and is to
be transformed to the form of a crisp number in the model of defuzzification. The high defuzzification is chosen
as the defuzzication method and is expressed as
(9)
where, jz is the amount of control output at the quantization level ,j ( )ju z is membership valve in jz and n is
number quantization levels of the output. The centroid method is used to implement defuzzication in Eq. (9).
The output signal is determined by consideration from the membership function of the fuzzy controller for the
hydraulic position and also of the hydraulic velocity. According to the fuzzy method, we assume that the
hydraulic position is a number in the interval from -255 to 255 and the limit of the membership function is -100
mm to 100 mm. At the same time, the hydraulic velocity is a number in the interval from -255 to 255 and the
limit of the membership function is from -100 mm/s to 100 mm/s. The microcontroller applies fuzzy control to
control the movement of the piston. Thus, membership function of the hydraulic position follows the following
equations:
( 65) /35 65 100,
( )
0 ,
x when x
VPOS x
otherwise
−  
= 

(10)
(100 )/35 65 100,
( ) ( 35)/30 35 65,
0 ,
x when x
POS x x when x
otherwise
−  

= −  


(11)
(65 )/30 35 65,
( ) /35 0 35,
0 ,
x when x
SPOS x x when x
otherwise
−  

=  


(12)
(35 )/35 0 35,
( ) ( 35)/35 35 0,
0 ,
x when x
ZE x x when x
otherwise
−  

= + −  


(13)
/35 35 0,
( ) ( 65)/30 65 35
0 ,
x when x
SNEG x x when x
otherwise
−  

= + −   −


(14)

(35 )/30 65 35,
( ) ( 100)/35 100 65,
0 ,
x when x
NEG x x when x
otherwise
− + −  

= + −   −


(15)
(65 ) /35 100 65,
( )
0 ,
x when x
VNEG x
otherwise
− + −   −
= 

(16)
Membership function of the hydraulic velocity follow the following equations:
. ( 65) /35 65 100,
( )
0 ,
x when x
VPOS x
otherwise
−  
= 

(17)
.
(100 )/35 65 100,
( ) ( 35)/30 35 65,
0 ,
x when x
POS x x when x
otherwise
−  

= −  


(18)
.
(65 )/30 35 65,
( ) /35 0 35,
0 ,
x when x
SPOS x x when x
otherwise
−  

=  


(19)
.
(35 )/35 0 35,
( ) ( 35)/35 35 0,
0 ,
x when x
ZE x x when x
otherwise
−  

= + −  


(20)
.
/35 35 0,
( ) ( 65)/30 65 35
0 ,
x when x
SNEG x x when x
otherwise
−  

= + −   −


(21)
.
(35 )/30 65 35,
( ) ( 100)/35 100 65,
0 ,
x when x
NEG x x when x
otherwise
− + −  

= + −   −


(22)
. (65 ) /35 100 65,
( )
0 ,
x when x
VNEG x
otherwise
− + −   −
= 

(23)
The hydraulic servo system were achieved for the position control of slider. Thus, membership function of the
hydraulic output follow the following equations:
( 204)/51 204 255,
0 ,
x when x
VPOS
otherwise
−  
= 

(24)
(255 )/51 204 255,
( 102)/100 102 204,
0 ,
x when x
POS x when x
otherwise
−  

= −  


(25)
(204 )/100 102 204,
/102 0 102,
0 ,
x when x
SPOS x when x
otherwise
−  

=  


(26)

(102 )/102 0 102,
( 102)/102 102 0,
0 ,
x when x
ZE x when x
otherwise
−  

= + −  


(27)
/102 102 0,
( 204)/100 204 102
0 ,
x when x
SNEG x when x
otherwise
−  

= + −   −


(28)
(102 )/100 204 102,
( 255)/51 255 204,
0 ,
x when x
NEG x when x
otherwise
− + −  

= + −   −


(29)
(204 ) /51 255 204,
0 ,
x when x
VNEG
otherwise
− + −   −
= 

(30)
V. EXPERIMENTAL SET UP
The proposed controller was also implemented in hydraulic servo system set up which was primarily developed
to be used in a motion simulator. The experiment setup is composed of a hydraulic system. A set of
experiments were performed to study the effect of variation in supply pressure, hydraulic parameters,
environmental stiffness and position control. In order to test performance of the developed system comparing
Simulink model. A typical closed loop controlled hydraulic system consists of power supply with 4 lit/min flow
rate and 60 bar supply pressure. The load 9 kg is connected to the piston rod. Load piston position is measured
by a FESTO Model TP 501 with 200 mm length of stroke and a 4-way 3 state proportional directional control
valve is measured by a VICKERS Model KBSDG4V-3. Linear potentiometer from a FESTO Model FP1120 is
used to record the position of the cylinder and DUPOMATIC Model PTH-100/20E0 pressure sensors are
measured P1 and P2 [24]. Consider a schematic of the experimental system shown in Fig. 9.
Fig. 9: A schematic diagram of the hydraulic servo system
VI. SIMULATION AND EXPERIMENT RESULTS
The object of Simulink is a hydraulic actuator, which is a representative hydraulic servo system. A simulation of
Matlab/Simulink based study is used to evaluate the performance of controllers on the nonlinear model of HSS
and compared with the performance of the PID control, Fuzzy control, and Hybrid of PID and Fuzzy control,
which are shown in Fig. 10. The parameters of the model must be identified for designing control algorithm, the
steps of identifying dynamic models of the hydraulic system involve designing an experiment, selecting a model
structure, choosing a criterion to fit, and devising a procedure to validate the chosen model.
Control
System
D/A Modulator Servo
Amplifier
Servo Valve
A/D
Ref
+
y
Position
Output
TransducerMicrocontroller
Digital
1 1,P Q
2 2,P Q
16 877PIC F
Section SectionAnalog
Cylinder
Pressure
Transducer

Fig. 10: Matlab Simulink Model of closed loop system
According to Figure above, first, the system is characterized by position control 1( )x . The piston stroke is
0.2 .m , mass of actuator and load m 9.19 .Kg= The friction relation is approximated as linear : 0.3063 .fF N
Secondly, the system is characterized by velocity control 2( ).x Let be a
differentiable function, given by i. e, we obtain the result in terms of
The response is a set of the velocity and its top most displacement range is Referring the
equation (9) . The line block is required for each channel, where velocity 2x is calculated.
For that, area and force are added in to the block while friction is subtracted from the block. The third method is
load pressure system 3( ).x This is the most effective method. The pressure of the system is set considering the
pressure of the load. Pressure limit is the supply pressure :5 .LP MPa The value of LP is determined by
substituting 3LP x= . To solve this equation, we may assume a solution 3x of the form
= (31)
First, all the models of components are composed and connected to the blocks. The load flow line parameters
are the sum of blocks from the function after passing through the function oC
block.
Overall, the main idea of the modified hydraulic subsystems is to use valve position ( )vx , valve velocity
and input current (u) . The upper and lower limits in servo valve are equal to the stroke of the servo valve
and the maximum flow limit through the valve
VII. VALIDATION
The main directions to model the dynamics behavior of a hydraulic servo system are various controls of model
complexity to achieve difference simulation and experiments. In case of the model validation and Hybrid
controller experiments, the controller is modeled using Simulink approach in Matlab program, comparing to the
0.16 / .m s
2 3
1
[ ( )]fx Ax F
m
= −
( )vx
4
: 2.38*10vx m−
 5 3
: 2.5*10 / .LQ m s−
3x 2
1
4
L
t
tm
e
Ax Q
V
C

 
 
 − +
 
+ 
 
sgn( )s v LP x P

−
1 2x dt x dt= 
1 2x x=
1 2
1
( )x x
s
=

position and velocity of PID, Fuzzy, and Hybrid of PID and Fuzzy controller which are based on an operating
supply pressure of 6 Mpa are shown in Figs. 11-13.
Fig. 11: Observer performance of step Fig. 12: Observer performance of step
responses with PID Controller responses with Fuzzy Controller
Fig. 13: Observer performance of step responses with Hybrid Controller
VIII. CONCLUSION
This paper documented the design, experimental evaluation and simulation of the position and velocity servo
control of a hydraulic mini press machine. The highly nonlinear behavior of the system limits the performance
of classical linear controllers used for this purpose. It was found that the proposed controller is better compared

with the traditional PID, Fuzzy, and Hybrid of PID and Fuzzy controllers both in simulations and experiments.
The scheme has been tested on various process in simulations and experiments where accurate speed control
with fast response times is 0.123 m/s and position is 42 mm. The simulations and experiments was found a good
effectiveness of the Hybrid of PID and Fuzzy method for HSS. The pressure control resulted in a performance
error which was lower than any performance error controlled with a keeping the system stable and the better
performance of a higher control precision have been obtained in position servo control system compare with
conventional PID and Fuzzy controllers.
REFERENCES
[1] Alleyne, A., & Liu, R. (2000). “Systematic control of a class of nonlinear systems with
application to electro – hydraulic cylinder pressure control”. IEEE transactions on control
systems technology, vol.8, 623 - 634.
[2] Amerongen, J.V., & Breedveld. (2003). “Modelling of physical systems for the design and control of
mechatronic systems”. Annual Reviews in Control, 87-117.
[3] Corke Li., D. P. I., & Gurgenci, H. Z. (1997). “Modelling and Simulation Simulation of an
Electro - Hydraulic Mining Manipulator”. Proceeding of the 1997 IEEE
International
Conference on Robotics and Automation, Albuquerque, New Mexico. Vol.2, 1663 - 1668.
[4] Dechrit, M., & Nitin, A. (2010). “Modeling, simulation and control of high speed nonlinear hydraulic
servo system”. World Journal of Modelling and Simulation Vol. 6 No. 1, 27-39.
[5] Ferreira, A. j., Sun, P., & Gracio, J. (2006). “Close loop control of a hydraulic press for
springback
Analysis”. Journal of Materials Processing Technology. 177, 377-381.
[6] Fung, F. R., Wang, C. Y., Yang, T. R ., & Huang, H . H. (1996). “Variable structure control with
proportional and integral compensations for electro - hydraulic position servo control
system”.
Mechatronics, vol.7, 1996, 67-81.
[7] Get ,S. S., Lee, T. H., & Ren, S. X. (2001). “Adaptive friction compensation of servo
mechanisms”.
International Journal of Systems Science, Vol. 32, pp. 523-532.
[8] Huang, Y. J., Kuo, T. C., & Lee, H .K.( 2007). “Fuzzy-PD Controller Design with Stability Equations
for
Electro - Hydraulic Servo Systems”. International Conference on Control, Automation and
Systems,
Seoul, Korea, 2407-2410.
[9] Khan, H., Abou, C. S . , & Sepehri, N. (2005). “Nonlinear observer – based fault detection
technique
for electro-hydraulic servo-positioning systems”. Mechatronics, 1037-1059.
[10] Lin, C., & Ren, L. (2005). “The Integrated Simulation Analysis on 6 DOF Electro - hydraulic
Servo – Control Parallel Platform”. JSME International Journal. vol. 48, 2005, 234-239.
[11] Liu, G. P., & Daley, S. (2001). “Optimal - tuning PID control for industrial systems”. Control
Engineering Practice 9, Vol.2, 1185-1194.
[12] Liu, G. P., & Daley, S. (1999). “Optimal - tuning PID controller design in the frequency domain
with application to a rotary hydraulic system”. Control Engineering Practice 7, 821-830.
[13] Li, H . X., & Tso, S. K. (1999). “A Fuzzy PLC with gain – scheduling control resolution for a
thermal
process- case study”. Control Engineering Practice, Vol.7, 523-529.
[14] Merritt, H . E. (1997). “ Hydraulic Control System”. John Wiley & Son, Inc. New York.
[15] Miroslav, M., Nikolic, V., & Antic, D. (2002). “Position Control of an Electro - Hydraulic
Servo System using Sliding mode Control Enhanced by Fuzzy PI Controller”. Mechanical
Engineering, Vol.1, 1217-1230.
[16] Moog, “Industrial Control Division”. (1995).
[17] Quing – Guo Kiong., T. K. W., Chieh, H . C., & Hagglung, T. J. (1999). “Advance in PID
Control”. Springer-Verlag, London Limited, Vol. 13, 3179-3185.
[18] Sirouspour, R . M. , & Salcudean, E. S . (2000). “On the Nonlinear Control of Hydraulic Servo –
Systems”. International Conference on Robotics & Automation, San Francisco CA,
[19] Sohl, G. A., & Bobrow , J. E. (1997). “Experiments and Simulations on the nonlinear Control
of a Hydraulic servo system”. Proceeding of the American Control Conference
Albuquerque,

New Mexico, Vol. 1, 631-635.
[20] Sun, P., Gracio, J. J ., & Ferreira, A. J. (2006). “Control system of a mini hydraulic press for
Evaluating spring back in sheet metal forming”. Journal of Material Processing
Technology, 55-61.
[21] Truong, D. Q., & Ahn, K. K. (2009). “Force control for hydraulic load simulator using self-tuning
grey predictor-fuzzy PID”. Mechatronics, 233-246.
[22] Vickers Product “Proportional Directional valve with Feedback”. (1999).
[23] Viljamaa, P., & Koivo, H. N. (1995). “Fuzzy Logic in PID Gain Scheduling”. Third
European
Congress on Fuzzy and Intelligent Technologies EUFIT’95, Aachen, German, August 28-31.
[24] Zhao, T., & Virvalo, T. (1995). “Fuzzy control of a hydraulic position servo with unknown
Load”. Fuzzy sets and systems, Vol. 70, 213-221.
[25] Zhao, T., & Virvalo, T., (1995). “Fuzzy control of a hydraulic position servo with unknown
Load”. IEEE, 785-788.
[26] Zhao, Y., Lequoc, S., & Saad, M. (1998). “Nonlinear Fuzzy Control on A Hydraulic Servo
System”. Proceedings of the American Control Conference Philadelphia, Pennsylvania, 2917-
2921.
Dechrit Maneetham, Design and Control of a Hydraulic Servo System and Simulation
Analysis. International Journal of Modern Research In Engineering & Management
(IJMREM), 1(7), 29-40. Retrieved August 10, 2018, from www.ijmrem.com.

Design and Control of a Hydraulic Servo System and Simulation Analysis

More Related Content

What's hot (20)

Similar to Design and Control of a Hydraulic Servo System and Simulation Analysis (20)

More from IJMREMJournal (20)

Recently uploaded (20)

Design and Control of a Hydraulic Servo System and Simulation Analysis