Drager Polytron 5000 Fixed Gas Detector - Spec Sheet
0 likes1,903 views
The Dräger Polytron 5000 is a stationary gas detector that can detect toxic gases and oxygen using electrochemical sensors. It has a durable design and high accuracy/sensitivity based on over 40 years of gas detection experience. The transmitter has an easy-to-use interface and calibration can be done without opening the hazardous area housing using a magnetic wand. Various models, sensors, and accessories are available for different applications.
Drager Polytron 5000 Fixed Gas Detector - Spec Sheet
- 1. Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: northernsales@thorneandderrick.co.uk Website: www.heattracing.co.uk Dräger Polytron 5000 Stationary gas detector (EC) PROVEN – AND STILL GETTING BETTER: DRÄGER MEASUREMENT TECHNOLOGY Dräger has been developing and manu-facturing sensors and gas detectors for industrial use for more than 40 years. And with each new device generation, we drive our measurement technology a bit further. With the Polytron 5000, you will definitely benefit from this experience and power of innovation: – durable sensors – short response times – high sensitivity – high accuracy – low sensitivity to other gases or changing ambient conditions www.thorneanderrick.co.uk OPTIONAL: TWO MOUNTING SETS FOR EASY FLANGE-MOUNTING The housing has four mounting holes. Two different mounting sets are available for installing the Polytron 5000: a duct-mount and a pipe mount set. This means that the transmitter can be easily installed anywhere – e.g., on a smooth wall, a pipe or an exhaust duct. QUICK AND EASY WIRING The electronics and the bezel form a single unit. Simply pull them out of the housing. Then insert the two-wire cable into the terminals. Finally plug the terminal block into the PCB. D-24180-2010 D-15065-2010 Dräger Polytron 5000 Flameproof transmitter for monitoring toxic gases and oxygen. The microprocessor-based transmitter can be equipped with various electrochemical DrägerSensors. This way, you can detect oxygen and various toxic gases in ambient air – reliably, quickly and cost-effectively, as the Polytron 5000 is the result of more than 40 years of experience in measurement technology. Same design, same operating principle: The Polytron 5000 series The Dräger Polytron 5000 is part of the Polytron 5000 series. All transmitters of this series have the same design and user interface, which guarantees a uniform operating philosophy. Your advantage: less training requirement and easier maintenance. Other transmitters of the Polytron 5000 serie: – Dräger Polytron 5200 (CatEx stationary gas detector) – Dräger Polytron 5310 (DSIR stationary gas detector) – Dräger Polytron 5700 (PIR 7000 stationary gas detector) – Dräger Polytron 5720 (PIR 7200 stationary gas detector)
- 2. DRÄGER POLYTRON 5000 - STATIONARY 02 | GAS DETECTOR (EC) EASY AND COST-EFFECTIVE: SINGLE-OPERATOR CALIBRATION The transmitter settings can be changed and maintenance carried out without opening the housing. Declassification of the hazardous, classified area is not necessary. Use the magnetic wand to quickly and easily select menu items and functions. An additional hand held terminal is not required. The sensor contains an integrated database where all important information is stored. This enables you to use pre-calibrated sensors. FURTHER ADVANTAGES: – Aluminum or 316 L stainless steel housing for the most extreme industrial conditions – Extremely user-friendly software thanks to a minimum number of menu items
- 3. DRÄGER POLYTRON 5000 - STATIONARY GAS DETECTOR (EC) | 03 TECHNICAL DATA Dräger Polytron 5000 Type Explosion proof transmitter Gases and Ranges Toxic gases and oxygen in discrete pre-set values, user selectable Display 3-digit LCD FSD (Full Scale Deflection) O2 25 vol% CO 50 / 100 / 200 / 300 / 500 ppm H2S zero-bias 10 / 20 / 50 / 100 ppm H2S LC 10 / 20 / 50 / 100 ppm H2S HC 100 / 200 / 300 / 500 ppm H2 500 ppm Cl2 **) 5 / 10 / 20 / 50 ppm EO *) 20 / 50 / 100 ppm NH3 LC **) 50 / 100 ppm NH3 HC **) 300 / 500 ppm NO *) 50 / 100 ppm NO2 **) 5 / 10 / 20 / 50 / 100 ppm SO2 **) 5 / 10 / 20 / 50 / 100 ppm H2O2 LC **) 5 / 10 / 20 / 50 / 100 ppm Electrical data Signal Output Normal operation 4 to 20 mA Maintenance 4 mA ± 1 mA 1 Hz modulation, or steady 3 mA; user selectable Fault < 2 mA Supply Voltage 16 to 30 VDC, 2-wire Ambient conditions Temperature -40 to + 150 °F / - 40 to + 65 °C (see also sensor data sheet) Pressure 20.7 to 38.4 inch Hg / 700 to 1300 mbar Humidity 0 to 100 %RH, non-condensing Enclosure Transmitter housing epoxy-coated copper free aluminum or 316L stainless steel Sensor housing 316L stainless steel Enclosure Rating NEMA 4X & 7, IP 65/66/67 Cable Entry 3/4" NPT female conduit entry Size (l x w x d, approx.) 9.5'' x 5.8” x 5.1'' / 240 x 150 x 130 mm Weight (approx.) aluminum 5.9 lbs / 2.7 kg stainless steel 9.7 lbs / 4.4 kg Approvals UL, CSA ***) Class I, Div 1, Groups A, B, C, D; Class II, Div 1, Groups E, F, G Class I, Zone 1, Group IIC, T-Code T6 / T4 -40°C ≤ Ta ≤ +40/+80°C ATEX, IECEx II 2G Ex d IIC T6/T4 Gb, -40°C ≤ Ta ≤ +40/+80°C; II 2D Ex tb IIIC T80/130°C Db, -40°C ≤ Ta ≤ +40/+80°C CE-mark ATEX (directive 94/9/EC) Electromagnetic compatibility (directive 2004/108/EC) Low voltage (directive 2006/95/EC) *) Notice: Gases which react with moisture will not repeatable pass through the wire mesh, if the transmitter is installed in a non-climate controlled environment. If it can be ensured, that condensation on the wire mesh will not occur; all sensors can be used in the explosion proof versions 45 44 120, 45 44 122. Other wise, these sensors should only be used with Polytron 5000 General Purpose 45 44 165. **) Notice: Only to be used with Polytron 5000 General Purpose 45 44 165. ***) CSA Pending
- 4. DRÄGER POLYTRON 5000 - STATIONARY GAS DETECTOR (EC) ORDER INFORMATION Dräger Polytron 5000 aluminum enclosure without sensor; UL, CSA, ATEX ***) 45 44 120 Dräger Polytron 5000 316L stainless steel enclosure without sensor; UL, CSA, ATEX ***) 45 44 122 Dräger Polytron 5000 aluminum enclosure without sensor; general purpose 45 44 165 Magnetic wand for menu access (blue body, white logo) 45 44 101 Pipe Mount Kit 45 44 198 Duct Mount Kit Polytron 5000 68 12 725 Splash Guard 68 12 510 Calibration Adapter PE 45 09 314 Calibration Adapter PE, Europe 68 06 978 Calibration Adapter Viton 68 10 536 DrägerSensor O2 LS 68 09 630 DrägerSensor CO 68 09 605 DrägerSensor H2S zero-bias 68 10 435 DrägerSensor H2S LC 68 09 610 DrägerSensor H2S HC 68 09 710 DrägerSensor H2 68 09 685 DrägerSensor Cl2**) 68 09 665 DrägerSensor EO*) 68 10 740 DrägerSensor NH3 LC**) 68 09 680 DrägerSensor NH3 HC**) 68 09 645 DrägerSensor NO*) 68 09 625 DrägerSensor NO2**) 68 09 655 DrägerSensor SO2**) 68 09 660 DrägerSensor H2O2 LC**) 68 09 705 *) Notice: Gases which react with moisture will not repeatable pass through the wire mesh, if the transmitter is installed in a non-climate controlled environment. If it can be ensured, that condensation on the wire mesh will not occur; all sensors can be used in the explosion proof versions 45 44 120, 45 44 122. Other wise, these sensors should only be used with Polytron 5000 General Purpose 45 44 165. **) Notice: Only to be used with Polytron 5000 General Purpose 45 44 165. ***) CSA Pending Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: northernsales@thorneandderrick.co.uk Website: www.heattracing.co.uk www.thorneanderrick.co.uk