Introduction to Embedded Systems

Introduction to Embedded Systems
by:
Eng. Mohamed Tarek.
1© 2015 by Eng. Mohamed Tarek.

Who am I ?
 BSc. degree in Communications and Electronics
Engineering from Cairo university.
 Software Engineer at Intel Mobile Communications
company from 8/2013 to 4/2014.
 Embedded Software Engineer at Mentor Graphics
company from 4/2014 till present.
 Part Time Embedded Systems
Instructor at ITI Suez canal
(Ismailia) branch.
 Part Time Embedded Systems
Instructor at AMIT-Learning
and SGEC courses centers.

Quotes
EVERY
EXPERT
was once a
BEGINNER

Quotes
 “Your work is going to fill a large part of your life,
and the only way to be truly satisfied is to do
what you believe is great work. And the only way
to do great work is to love what you do. If you
haven’t found it yet, keep looking. Don’t settle.
As with all matters of the heart, you’ll know when
you find it”
Steve Jobs, Apple co-founder
© 2015 by Eng. Mohamed Tarek. 4

Quotes
 “There are people who make things happen,
there are people who watch things happen,
and there are people who wonder what
happened.”
Jim Lovell, Apollo 13 mission commander
 Watch 75%
Wonder 20%
Make 5%
I hope I am here

Notes
 Ask any time.
 Turn your cell silent.
 Feel free to refer to anything; internet for
example.

 Agenda
• Embedded Systems Definition.
• Embedded Systems Characteristics.
• Embedded Systems Applications.
• Embedded Systems Design.
• Embedded HW
 Processing Engines.
 Micro-processor vs. Micro-controller.
 Micro-controller main components.
 Micro-controller other components.
• Embedded Systems Constrains.
• Embedded Systems Market.

 Agenda
• Embedded HW

Embedded Systems Definition
 All systems that contain one or more processing units
usually it is micro-controller to do specific functionalities
and give responses upon receiving inputs, This
processor is not for general purposes like general
purpose Processor in PC’s and notebooks.
 Computing systems with tightly coupled hardware and
software integration, that are designed to perform a
dedicated and repeated function.

 The word embedded reflects the fact that these systems
are usually an integral part of a larger system, known as
the embedding system. Multiple embedded systems can
co-exist in an embedding system.
 Embedded Systems are Application-specific systems
which contain hardware and software tailored for a
particular task and are generally part of a larger system.
 Historically, the term embedded systems was used to
describe any non-PC-related system, but in time, the
definition has grown to include any system that is
dedicated to a particular functionality.

 Can Personal Computer be considered as an
Embedded System as it integrates hardware and
software to perform functions? Why?
• PC cannot be considered as an
embedded system because :
1. It uses a General-Purpose Processor.
2. The system is built independently from the
software runs on it.

 Agenda
• Embedded HW

Embedded Systems Characteristics
 Reliability
• Personal computer programs such as word
processors and games do not need to achieve the
same standard of reliability that a microcontroller
application must. Errors in programs such as word
processors may result in errors in a document or loss
of data. An error in an Embedded system application
such as a TV remote control or compact disc player
will result in a product that does not work and
consequently does not sell.
• An error in Embedded system
application such as an antilock
braking system or autopilot could
be fatal.

 Efficiency
• Considered in real time applications.
• A real time application is one in which must be able to act at a
speed corresponding with the occurrence
of an actual process. must compute
certain results in certain real-time
without delay.
• Some Embedded systems may have
real-time performance constraints that
must be met, for reasons such as safety
and usability. others may have low or no
timing performance requirements,
allowing the system hardware to be
simplified to reduce costs.

 Tightly-constrained
Embedded Systems normally come with constraints in
hardware resources:
• Processing(speed)
• Memory(Data)
• Storage(Code Size)
• Most of the time it targets real time objectives, this
means,
 It needs to be fast and efficient(Response Time).
 It needs to be predictable (execution time known ahead,
and almost constant)
• Power limited(battery operated devices).
• Cost
• Size

 The developer has to deal with all of these
constraints
• Development should take into consideration code
efficiency and code foot print.
• Debugging tools are “closer to the metal”
• Special attention to power consumption in some
cases.

 Single-functionality
Dedicated to perform a specific function and include
processors dedicated to specific function.
 Complex functionality
Often have to run sophisticated algorithms or multiple
algorithms Cell phone, laser printer, automotive, etc.
 Safety-critical
Must not endanger human life and the environment

 Maintainability
The ability to modify the system after its initial release
and enhance its performance like execution time, code
and memory size.
 Interactive System
An Embedded system should be as interactive as
possible so that it is easily understandable, Operated
and Handled by a user and provide ease of task.
 Strong association between the HW and SW.

Comparison
 Computing a lot of applications
(i.e. general purpose).
 Programmable by end user
 Faster is better
 Criteria
• Cost
• Average speed
General Purpose Systems
 Perform ONLY Few
applications that are known
at design-time (i.e. special
purpose).
 Not programmable by end
user.
 Fixed run-time requirements
(additional computing power
not useful).
 Criteria
• Cost
• Power consumption
• Deterministic behavior
• Meeting time bounds
• Size
Embedded Systems

 Agenda
• Embedded HW

Embedded Systems Applications
 Exercise
Choose two Embedded Systems and list the main
functionalities of each one.

 Automotive

 Automotive
• Electronics represents 40% of total cost of a car.
• 90% of new car features require software.

 Automotive

 ECUs are used in different functions of the car :
• Engine Control
• Transmission Control
• Fuel Efficiency Control
• Electric Power Steering
• Speed Control
• Brake Control
• Suspension System Control
• Battery Management
• Seat Control
• Door Control
• Electric Windows Control
• Lighting Control
• Airbag Control
• Telemetric Control
• Mirror Control
• Security System
Control
• Windshield Blades
Control
• Entertainment
• Human-machine
interface (HMI)
• And a lot more …..

 Phones and Tablets
26
Contains mainly three types of
processors:
1. Communication Processor(s)
 Wifi
 GSM/3G/LTE
 Bluetooth/NFC
2. Audio/Graphics Processor(s)
 Audio Processing
 Graphics and Video
Processing
3. Application Processor
 Android
 Windows Phone
 iOS
© 2015 by Eng. Mohamed Tarek.

 Telecommunication systems

 Networking Devices

 Robotics

 Product: NASA's Mars Sojourner Rover 1996,low cost
spacecraft . Using 8-bit Intel Microprocessor 80C85.

 Image Processing

 Electronic Devices

 Appliances

 Aircraft Control

 Military

 Agenda
• Embedded HW

Embedded Systems Design
 Trade off between SW & HW
For a certain application:
• Which functional blocks should be performed in
Hardware??
• Which functional blocks should be performed in
software??

 Software characteristics
• Advantages
 Highly configurable
 Shorter development cycle
 Easier in versions updates
 Cheaper
• Disadvantages
 Constrained with processor speed which may
satisfy real time application and may not.

 Hardware characteristics
• Advantages
 Better performance in high speed real time
application
• Disadvantages
 Longer development cycle.
 Customized for specific application, not updatable
(unchangeable).

 HW/SW Partitioning
In complicated systems functional blocks could be:
• Level I: external discrete hardware component on
board
• Level II: hardware integrated with CPU on chip
system on chip (SOC)
• Level III: done by software running on CPU

 HW/SW Partitioning
• Design and build the target hardware
• Develop the software independently
• Integrate them and hope it works

 Embedded Systems Design Steps
1. Modeling via any modeling language (System C or
even Matlab)
2. HW/SW partitioning (Determine which blocks must be
H/W & which may be S/W)
3. Global Design of the S/W part
4. Unit Design of the S/W part
5. Coding.
6. Unit Testing.
7. Integration Testing.
8. Verification and Validation.
9. Maintaining.

 Embedded Systems Design Challenges
• Find an implementation that can perform the
computation such that the requirements are satisfied.
• Embedded systems perform computations (software)
that are subject to physical constraints (hardware)
• Execution on a physical platform: processor speed,
power, storage, reliability.
• Computer science separates computation from
physical constraints

 Design goals
• Performance(overall speed execution time
and throughput).
• Functionality and user interface.
• Manufacturing cost.
• Power consumption.
• Safety.
• Other requirements. (physical size, etc. )

 Agenda
• Embedded HW

1.General Purpose Processor
 CPU = ALU + Registers + Control unit
 32 or 64-bit data path.
 Modern Processors have:
• Advanced cache logic.
• Built-in math co-processor capable of performing fast
floating-point operations(FPU).
• A built-in memory management unit (MMU) to provide
memory protection and virtual memory for
multitasking-capable.
• Interfaces to support a variety of external peripheral
devices because Microprocessor alone is useless.

1.General Purpose Processor(Cont.)
 Complex in design because these processors provide a
full scale of features and a wide spectrum of
functionalities.
 These processors result in large power consumption,
heat production, and large size.
 Intel X86, Intel Pentium , AMD, PowerPC and SPARC.

2.Embedded General Purpose Processor
 16/32-bit data path.
 Designed for a wide range of applications (consumer
and communication).
 Limited functionality depending on the application.
 Not Flashable the program memory is external and have
CASH memory and MMU.
 Usually integrated into larger dedicated systems in a
SOC (System on Chip), also called core-based ASIC.
 Have main peripherals Like Timers, Ethernet, USB and
GPIO
 ARM has seized the lion’s share of the market.

3.Digital Signal Processor
 Like microprocessor but focus on very efficient execution
of arithmetic operations.
 Digital signal processing algorithms typically require a
large number of mathematical operations to be
performed quickly and repeatedly on a series of data
samples. Signals (perhaps from audio or video sensors)
are constantly converted from analog to digital,
manipulated digitally by DSP processor, and then
converted back to analog form.

 Used widely in digital signal processing in
communication systems such as Cell phones, Image
and video processing.
 Even though DSPs are incredibly fast and powerful
embedded processors,
 Examples: TI (Texas Instruments), Motorola.
 TI has been the dominant player in the DSP market for
several years.

4.Microcontrollers
 Microcontroller = CPU + Memory + Peripherals.
 Microcontrollers are often referred to as single chip
devices or single chip computers in a small size that its
resources are more limited than those of a desktop
personal computer.
 Included memories (RAM, ROM), I/O Ports, buses and
peripherals depending on the application designed for
(ADC, Timers, USART, I2C , SPI and ..).
 The workhorse of industrial electronics.
 Designed for standalone operation.
 Include a processing unit of 8-bit, 16-bit or 32-bit.

System on Board

System on chip(SOC)

System on chip(SOC)
 A SOC has multiple functional units on one piece of
silicon, Integrating all components of a computer or other
electronic systems into a single integrated circuit (chip).
 Due to advancements in silicon technologies, it is
possible to add more functionalities to the processor
system on chip like Co-processors, Memories, Internal
I/O devices and Interrupt circuit.
 For example, a system-on-a-chip for a sound-detecting
device might include an audio receiver,
an analog-to-digital converter
( ADC ), a microprocessor, memory,
and the input/output logic control for
a user all on a single micro-chip.
 Typically application is in the
area of embedded systems.

Advanced Embedded Systems
 Network of embedded micro-controllers on
board
Many micro-controllers on one / many board(s)
communicate together through specific bus protocol
like LIN bus and CAN bus in automotive applications.

 Multi-Core system on chip like mobile
handset which has one chip contains:
• DSP Processor for graphics and image processing.
• Embedded Processors like: ARM.
• Custom hardware for Wi-Fi, Bluetooth
and LTE(4G Network).
• Custom peripherals for board interface:
 GPS.
 Touchscreen interface.
 Memory card interface.

 Agenda
• Embedded HW

Micro-controller vs. Micro-processor
 Micro-controller
• Basically a microcontroller can be described as
a computer on a chip. a single chip containing
a CPU, non-volatile memory (ROM), volatile
memory(RAM), a timer and an I/O control unit.
• A microcontroller apart from the above mentioned
components usually also include serial
communication capabilities, interrupt controls and
analog I/O capabilities.
• Used for a few dedicated functions determined by
the system designer.

Many IC’s into one IC

 Microcontrollers don’t work alone in the circuit it must
interfaces with other on chip devices like Sensors,
Switches, Leds, LCD, Keypad and DC Motor.
 Microcontroller can accept inputs from some
components and provide outputs to other components
within any given system.
 Differences in requirements, make the manufacturers
produce different microcontrollers with different
memory sizes, number of I/O lines and number of
integrated peripheral devices. Other wise they are all
similar to use.

 Micro-processor
• Just a CPU has to add externally memory, clock,
input/output interfaces, timer and all other
needed peripheral. This is the reason
a microprocessor has so many pins.
• The difference between a microcontroller and
a microprocessor is that the microprocessor is
a general purpose computer while a microcontroller
is a computer dedicated to one or just a few tasks.

 Agenda
• Embedded HW

Micro-controller main components
1. Central processing unit (CPU).
2. Memory units.
3. Input and Output ports (GPIO or DIO).
4. Timers.
5. Watch dog timer
6. Buses.
7. Interrupt circuit.

Micro-controller main components
 In the following slides we will try to understand
the different components in any microcontroller
then map these information to AVR
microcontrollers

1.Cental Processing Unit(CPU)
 The central processing unit (CPU) does all the
computing: it fetches, decodes and executes program
instructions and directs the flow of data to and from
memory. The CPU performs the calculations required by
program instructions and places the results of these
calculations, if required into memory space.
 The unit which monitors and controls all processes
inside the microcontroller. It consists of several smaller
units.

 Example Assembly Instruction for AVR CPU
70
Instruction OP-Code
LDI Rd, k (0≤k≤255) 1110 – kkkk – dddd – kkkk
LDI R10, 255 1110 – 1111 – 1010 – 1111

 The most important units inside CPU are:
• Arithmetic Logic Unit(ALU).
• Instruction Decoder(Control Unit).
• Accumulator Register.
• Register File.
• SFR Registers.

 Arithmetic Logic Unit
Part of the CPU is responsible for performing
calculations and execution for Arithmetic, Logic and Shift
instructions.
• Arithmetic instructions include:
 Addition
 Subtraction
 shifting operations
• Logic instructions include:
 AND
 OR
 XOR
 NOT operations

 Instruction Decoder(Control Unit)
• Converts instructions stored or fetched in program
memory into codes which the ALU can understand
and generate the control signals of this instruction.
• The control unit is the circuitry that controls the flow of
data through the processor, and coordinates the
activities of the other units within it.
• In other word it is in charge of the entire Instruction
(Machine) cycle
• The “instruction set” differs from microcontroller
family to another expresses the abilities of this circuit.

 Instruction Decoder(Control Unit)

 Accumulator Register
Is an SFR closely related to the operation of the ALU. It
is a kind of working desk used for storing all data upon
which some operations should be performed (addition ,
shift, Subtraction, etc.).

 Register File
• A number of registers grouped together.
• n data bits and k address bits.
• We can read two registers at once by supplying AA,
BA and WR = 0.
• We can write at a register using the DA and D inputs
and setting WR = 1

 Register File in AVR CPU
• AVR CPU contains 32 registers R0  R31.

 SFR Registers
The numbers and names of registers vary drastically
among microcontrollers. However there are certain
registers which are common to most of microcontrollers,
although the names may vary.
1. Instruction Register(IR)
• Register which contains the instruction after getting it from
program memory (Fetch stage).
• The ATmega16 contains 16 Kbytes On-chip
In-System Reprogrammable Flash EEPROM
memory for program storage. Since Most AVR
instructions are 16 bits wide, the Flash is
organized as 8K × 16. so The ATmega16
Instruction Register is 16 bits wide.

2. Program Counter(PC)
• Perhaps the most important CPU register is the
program counter(PC).
• The PC holds the address of the next instruction in
program memory space, which the CPU will process.
As each instruction is fetched and processed by the
ALU, the CPU increments the PC and there by steps
Through the program stored in the program memory
space.
• The ATmega16 contains 16 Kbytes On-chip
In-System Reprogrammable Flash EEPROM memory
for program storage. Since most AVR instructions are
16 wide, the Flash is organized as 8K × 16. so The
ATmega16 Program Counter (PC) is 13 bits.

3. Stack Pointer(SP)
• The stack pointer is basically a register that holds
either "the memory address of the last location on that
stack where data was stored" or "the memory address
of the next available location on the stack to store
data.“ last case is more common in CPU
architectures.
• The Stack is implemented as growing from higher
memory locations to lower memory locations. This
implies that a Stack PUSH command decreases the
Stack Pointer and a Stack POP command increases
the Stack Pointer(and may be vice versa for some
processors).
80

2.Memory Units
 Stack
• The Stack is mainly used for storing temporary data,
for storing local variables and for storing return
addresses after interrupts and subroutine calls.
• Store data in stack using PUSH and POP operators.
• A stack is a LIFO (last in, first out) mechanism the last
thing store on the stack is the first thing to be
retrieved from the stack.

• Stack Pointer Register in AVR CPU
 The AVR Stack Pointer is implemented as two 8-bit
registers in the I/O space. The number of bits actually
used is implementation dependent on SRAM Data
memory size. Note that the data space in some
implementations of the AVR architecture is so small
that only SPL is needed. In this case, the SPH
Register will not be present.
 SRAM in ATmega16 is 1KB it divided to 1K x 8 so the
Stack Pointer is 10 bits wide.

• Stack Pointer have to be initialized to point to the last
memory location in SRAM (i.e. first empty location in the
stack).

• Stack after first PUSH

• Stack after Second PUSH

86
• Stack after First POP.

• Stack after Third PUSH.

4. Index Register
• Used to specify an address when certain addressing
modes are used, And Known as pointer register like
X,Y and Z registers in AVR CPU.
• Also called Base Register or Pointer Register.
• Used in indirect addressing modes, as the accessed
address = index register + offset mentioned in code.

 X,Y and Z Index Registers in AVR CPU
• The R26..R31 registers have some added functions
to their general purpose usage. These registers are
16-bit address pointers for indirect addressing of the
Data Space.

5. Processor Status Word/Register(PSW)
• The Status Register contains information about the
result of the most recently executed arithmetic
instruction. This information can be used for altering
program flow in order to perform conditional
operations.
• Status Register is updated after ALU operations.
 Status Register in AVR CPU

• Flags as:
 Bit 0 –C: Carry flag
indicates a carry in an arithmetic or logic operation.
 Bit 1 –Z : Zero flag
indicates a zero result in an arithmetic or logic
operation.
 Bit 2 –N: Negative flag
indicates a negative result in an arithmetic or logic
operation.
 Bit 3 –V : Overflow flag
indicates an overflow occurs in an arithmetic
operation.

 Bit 4 –S: Sign Flag
indicates the result sing of arithmetic operation.
 Bit 5 –H: Half-carry flag
indicates a Half Carry in the least significant four bits in
arithmetic operations.
 Bit 6 –T: Bit Copy Storage
The Bit Copy instructions BLD (Bit Load) and BST (Bit
store) use the T-bit as source or destination for the
operated bit. A bit from a register in the Register file can
be copied into T by the BST instruction, and a bit in T
can be copied into a bit in a register in the Register file
by the BLD instruction.
 Bit 7 –I: Global Interrupt Enable: Global Interrupt
mask bit
must be set for the interrupts to be enabled.

Instruction life cycle

 Instruction Pipelining:
• Continuous and parallel streaming of instruction to the
CPU.
• A method of achieving higher execution speed at
same clock speed.

 The Parallel Instruction Fetches and
Instruction Executions in AVR CPU

97
Simple CPU Architecture

CPU Architecture(Memory accessing):
• There are two basic types of architecture:
 Von-Neumann Architecture.
 Harvard Architecture.
• Microcontrollers most often use a Harvard
Architecture or a modified Harvard-based
architecture.

 Harvard architecture
computers have separate
memory areas for program
instructions and data.
 One bus connects CPU to
RAM memory(Data
Memory). The other bus
connects CPU to ROM
memory(Program
Memory).
Harvard Architecture
 Von-Neumann
architecture has a single
and common memory
space where both
program instructions and
data are stored.
 There is a single data bus
which fetches both
instructions and data.
Von-Neumann Architecture

 The CPU can read an
instruction and perform a
data memory access at the
same time.
 This speeds up execution
time but increases the cost
of more hardware
complexity.
 Each time the CPU
fetches a program
instruction it may have to
perform one or more
read/write operations to
data memory space, it
must wait until these
subsequent operations
are completed before it
can fetch and decode the
next program instructions.

 The advantages of this
architecture lies in its
speed. But with more HW,
cost and complexity.
 The advantages of this
architecture lies in it’s
simplicity and economy
(only 1 memory + few
number of wires).

CPU Architecture(Number of instructions):
• There are two basic types of architecture:
 Reduced Instruction Set Computing(RISC).
 Complex Instruction Set Computing(CISC).
• Microcontrollers most often use a RISC Architecture.

 CPU design that
recognizes a large number
of instructions, Complex in
design.
 Complex and Large no. of
instructions.
 Large execution time for
each instruction.
 Instructions can operate
directly on memory.
CISC Architecture
 CPU design that
recognizes only a limited
number of instructions,
Simple in design.
 Simple instructions.
 Instructions are executed
quickly.
 Only the load and store
instructions operate
directly onto memory.
RISC Architecture

 CISC is an old concepts
that dates back when
memory access was slow.
 CISC aimed to integrate
several functionalities in
one instruction, in order to
limit the program size. and
thus limit memory access
in order to gain some
speed.
CISC Architecture
 RISC aims to optimize
execution of instructions
by limiting the capabilities
of a single instruction and
having consistent
instructions’ execution time
(Instruction Pipelining)
 thus gaining speed from
execution point of view but
code size will be large for
a dedicated function. But it
will increase the number of
memory access.
RISC Architecture

 It's easier to write powerful
optimized compilers, since
fewer instructions exist.
 Small number of general
purpose registers.
 Example: Intel X86, AMD
and Motorola 68000.
CISC Architecture
 So It's harder to write
powerful optimized
compilers, since large
number of instructions
needed.
 Combine a large number
of general registers for
arithmetic operations to
avoid storing variables on
a stack in memory.
 Example: ARM, AVR,
PIC,POWER-PC and
SPARC.
RISC Architecture

 Consider this example:
This CISC assembly code
clear 0x1000 ;clear memory location 0x1000
load r1,#5 ;load register 1 with the value 5
Becomes the following RISC assembly code
xor r1,r1 ; clear register 1
store r1,0x1000 ; clear memory location 0x1000
load r1,#5 ; load register 1 with the value 5

 Consider multiplying two numbers, then adding the same
two numbers. A CISC machine will get the two values
from memory, perform the multiplication, then store the
result. It would then have to re-retrieve the same two
values from memory and perform the addition and store
the result. A RISC machine would pull the two values
from memory, perform the multiplication, then store the
result, but an optimizer would see that the values are
already local to the processor and would skip re-
retrieving these values from memory thus saving a
number of internal clock cycles, and the more expensive
memory access cycles.

 Block diagram of the AVR Core architecture.
• Note the:
 Different memories
 Special Purpose Registers
 General Purpose Registers
 Special Purpose “units”
 ALU

• The blocks shown in blue are typical of a
microprocessor. The other
blocks, e.g. memories and
special purpose units are
what defines the difference
between a microprocessor
and a microcontroller.
• The main function of the
CPU core is to ensure
correct program execution.
The CPU must therefore
be able to access
memories, perform
calculations, control
peripherals and handle interrupts.

• In order to maximize performance and parallelism, the
AVR uses a Harvard
architecture with separate
memories and buses for
program and data.
Instructions in the program
memory are executed with
a single level pipelining.
While one instruction is
being executed, the next
instruction is pre-fetched
from the program memory.
This concept enables
instructions to be executed
in every clock cycle. The program memory is In-System
Reprogrammable Flash memory.

• The fast-access Register file contains 32 x 8-bit general
purpose working registers
with a single clock cycle
access time. This allows
single-cycle Arithmetic
Logic Unit (ALU) operation.
In a typical ALU operation,
two operands are output
from the Register file,
the operation is executed,
and the result is stored
back in the Register file
in one clock cycle.

• Six of the 32 registers can be used as three 16-bit
indirect address register
pointers for Data Space
addressing –enabling
efficient address
calculations. One of the
these address pointers
can also be used as an
address pointer for look up
tables in Flash Program
memory. These added
function registers are the
16-bit X-register, Y-register
and Z-register.

• The ALU supports arithmetic and logic operations
between registers or
between a constant and
a register. Single register
operations can also be
executed in the ALU.
After an arithmetic
operation, the Status
Register is updated to
reflect information about
the result of the operation.

• The high-performance AVR ALU operates in direct connection with
all the 32 general purpose
working registers. Within a
single clock cycle, arithmetic
operations between general
purpose registers or between a
register and an immediate are
executed. The ALU operations
are divided into three main
categories – arithmetic, logical,
and bit-functions. Some
implementations of the
architecture also provide
a powerful multiplier supporting
both signed/unsigned
multiplication and fractional
format.

116
• Program Execution: Hex Code is what is stored in the
Flash Program memory.
When the program runs,
the hex code is accessed
by the Program Counter.
It loads the next instruction
into a special Instruction
Register. The operands
of the instruction are fed
into the ALU , while the
instruction itself is
decoded by Instruction
Decoder and then
executed by the ALU.

2.Memory Units
 Memory is a part of the microcontroller used for data and
program storage.
 Each memory address corresponds to one memory
location. The contents of any location can be accessed
and read by its addressing. Memory can either be written
to or read from.
 There are different types of
memories inside the microcontroller:
• RAM memory (Random Access
Memory) used as Data memory.
• ROM memory (Read Only Memory)
used as program memory.

2.Memory Units
 RAM(Random Access Memory)
• Also called Read/Write Memory, The term random
access refers to the ability to access any memory cell
directly.
• RAM is volatile: if you remove the power supply its
contents are lost.
• Used to store data as long as Microcontroller is
powered and the program is running.
• Any variable used in a program is allocated into RAM.
• Modifiable through program instructions.

2.Memory Units
 RAM Types
1. Dynamic RAM(DRAM)
• DRAM is a RAM device that has memory cells with a
paired transistor and capacitor.
• The capacitor arrays will hold their charge only for a
short period before it begins to diminish.
• it is required periodic refreshing every few
milliseconds to retain its content.
• If a processor access conflicts
with the need to refresh the
DRAM, the refresh cycle must
take precedence.

2.Memory Units
2. Static RAM(SRAM)
• SRAM uses multiple transistors, typically four to six,
for each memory cell.
• SRAMs use pairs of logic gates to hold each bit of
data.
• SRAM does not require periodic refreshing and it is
faster than DRAM.
• Their drawbacks are that their density is considerably
less than DRAM, while being much more expensive.

2.Memory Units

2.Memory Units
 Even though both SRAMs and DRAMs are volatile
memories, they have some important differences:
• Since the DRAM requires a single capacitor and a
transistor for each memory cell, it is much simpler in
the structure than the SRAM, which uses six
transistors for each memory cell.
• On the other hand, due to the use of capacitors,
DRAM requires to be refreshed periodically as
opposed to the SRAM.
• DRAMs are less expensive and slower than SRAMs.
• Therefore they are used for the large main memory of
personal computers, workstations, etc., while SRAM
are used for the smaller and faster cache memory.

2.Memory Units
3. Non-Volatile RAM (NVRAM)
• NVRAM is a special type of SRAM that has backup
battery power so it can retain its content after the
main system power is shut off.
• Another variation of NVARM combines SRAM and
EEPROM so that its content is written into the
EEPROM when power is shut off and is read back
from the EEPROM when power is restored.

2.Memory Units
 RAM Divided virtually to
• General purpose registers for CPU acts as
accumulators (AVR Architecture).
• Peripherals control special registers like I/O PORTS,
timer, UART, etc. registers.
• All global and static variables are stored in RAM.
• Stack: store local variables and used to save the
present context state when interrupt occurs.

2.Memory Units
125
 SRAM Memory Mapping in ATmega16 µC
• The 1120 Data bytes Memory
locations address the Register
File, the I/O Memory, and the
internal data SRAM.
• The first 32 locations address the
Register File.
• The next 64 locations address
the I/O functions, ADC, Timers,
USART,SPI and other peripherals.
• The next 1024 locations address
the internal data SRAM.

2.Memory Units
• Memory Mapped I/O is to use the same address bus to
address Peripherals (i.e. I/O Devices), CPU registers
and Memory.
• In Memory Mapped I/O when address is accessed by the
CPU, it may refer to a portion of physical RAM, but it can
also refer to peripherals control special registers.
• To accommodate the I/O devices, areas of the
addresses used by the I/O Devices must be reserved for
and must not be available for normal data memory.
• It takes memory from main memory which reduces the
memory available for applications.

2.Memory Units
 ROM(Read Only Memory)
• Permanent memory(Non-Volatile memory).
• Used as Program Memory in Micro-Controller.
• ROM generally slower than RAM.
• The size of program that can be written depends on
the size of this memory. Today’s microcontrollers
commonly use 16-bit addressing, which means that
they are able to address up to 64 Kb of memory, i.e.
65535 locations.
• Written upon programming the microcontroller.
• Can’t be written/modified at run time.

2.Memory Units
 ROM Types
1. Masked ROM
• Programmed by the manufacturer.
• The term ‘masked’ comes from the manufacturing
process.
• In case of a large-scale production, the price is
very low.

2.Memory Units
2. OTP(one time programmable)
• Also called programmable ROM(PROM).
• enables programmer to download a program into it
one time only.
• Used when the firmware is stable and the product is
shipping in bulk to customers.
• If an error is detected after downloading, the only
thing you can do is to download the correct program
to another chip.

2.Memory Units
3. UV EPROM(UV Erasable Programmable
ROM)
• It enables data to be erased under strong ultraviolet
light.
• After a few minutes it is possible to download a new
program.
• the package of this microcontroller has recognizable
“window” on the upper side. It enables surface of the
silicon chip to be lit by an UV lamp, which has as a
result that complete program cleared and a new
program download enabled.

2.Memory Units
4. EEPROM (Electrically Erasable
Programmable ROM)
• Can be erased by exposing it to an electrical charge.
• The contents of this memory may be changed during
run time (similar to RAM), but remains permanently
saved even if the power supply is off (similar to ROM).
Accordingly.
• EEPROM is often used to read and store values,
created during operation, which must be permanently
saved.
• Acts as peripheral of microcontroller.
• Accessed through special registers in Micro-
Controller.

2.Memory Units
• Take more time in read/write access than RAM.
• Finite number of Write/Erase Cycles 100,000 in
ATmega16 µC.
• ATmega16 µC contains 512 Bytes EEPROM.
• Example, if you design an electronic lock or an alarm, it
would be great to enable the user to create and enter the
password, but it’s useless if lost every time the power
supply goes off. The ideal solution is a microcontroller
with an embedded EEPROM.

2.Memory Units
5. Flash EEPROM
• Invented in the 80s in the laboratories of Intel.
• Represented as the successor to the EEPROM.
• Flash is normally organized as sectors (256B - 16KB)
• Large blocks of memory erased at once, rather than
one word at a time like EEPROM, So FLASH is much
faster than EEPROM.
• The large block sizes used in flash memory give it a
significant speed advantage over old-style EEPROM
when writing large amounts of data like downloading
a µC application code.

2.Memory Units
 Flash EEPROM Memory in Atmega16 µC
• The ATmega16 contains 16K bytes
On-chip In-System Reprogrammable
Flash memory for program storage.
Since all AVR instructions are 16 or
32 bits wide, the Flash is organized
as 8K x 16.
• the Flash Program memory space is
divided into two sections, Boot
Program section and Application
Program section.
• The ATmega16 Program Counter
(PC) is 13 bits wide, thus addressing
the 8K program memory locations.

2.Memory Units
• Finite number of Write/Erase Cycles 10,000 Flash in
ATmega16 µC.
• Since the contents of this memory can be written and
cleared practically unlimited number of times most
microcontrollers program memory are manufactured
using flash technology.

2.Memory Units
 ROM Contents
• Program code.
• Interrupt Vector Table.
• Constant data Handled through const keyword in C.

2.Memory Units
 Most of micro-controllers contain SRAM memory as a
Data memory.
 Most of micro-controllers contain Flash EEPROM
memory as a program memory and EEPROM memory
as a peripheral. EEPROM is used to read and store
values created during operation, which must be
permanently saved.

2.Memory Units
138
Type Volatile? Writeable? Erase Size Max Erase
Cycles
Cost (per
Byte)
Speed
SRAM Yes Yes Byte Unlimited Expensive Fast
DRAM Yes Yes Byte Unlimited Moderate Moderate
NVRAM No Yes Byte Unlimited Expensive
(SRAM + battery)
Fast
Masked ROM No No n/a n/a Inexpensive Fast
PROM No Once, with a
device
programmer
n/a n/a Moderate Fast
EPROM No Yes, with a device
programmer
Entire Chip Limited (consult
datasheet)
Moderate Fast
EEPROM No Yes Byte Limited (consult
datasheet)
Expensive Fast to read, slow
to erase/write
Flash No Yes Sector Limited (consult
datasheet)
Moderate Fast to read, slow
to erase/write

Just for Knowledge
 Main memory
Large, inexpensive(DRAM), slow memory stores entire
program and data.
 Cache
Small, expensive(SRAM), fast memory stores copy of
likely accessed parts of larger memory, Can be multiple
levels of cache.

3.I/O Ports

3.I/O Ports
 The microcontroller has to be connected to additional
external electronics and peripherals.
 For that reason, each microcontroller has one or more
registers (called “port” in this case) to which it’s
connected.
 These ports are bidirectional could be output or input.
 Suppose you want your device to turn on and off three
signal LEDs and simultaneously monitor logic state of
five sensors or push buttons to the microcontroller pins.
 low-current consumption for Micro-Controller Pin (10-20
mA).
 Each I/O port is under control of another SFR, which
means that each bit of that register determines state of
the corresponding microcontroller pin.

3.I/O Ports

3.I/O Ports
Atmega16 µC Pins

4.Timer
 There are commonly 8-bit or 16-bit timer registers and
their content is automatically incremented by each
coming clock cycle.
 Most microcontrollers have at least one timer/counter
peripheral. Timer/Counter modules are used to perform
timing or counting operations in the controller. These
include counting events, time passed between two
events, generate interrupt after a certain time and
generate PWM signals.

4.Timer
145
Timer Overflow Interrupt

4.Timer
 A prescaler is an electronic device used to reduce
frequency by a predetermined factor. In order to
generate one pulse on its output, it is necessary to bring
1, 2 , 4 or more pulses on its input. Most microcontrollers
have one or more prescalers built in and their division
rate may be changed from within the program. The
prescaler is used when it is necessary to measure longer
periods of time. If one prescaler is shared by timer and
watchdog timer, it cannot be used by both of them
simultaneously.

5.Watch Dog timer
 Special kind of timers that triggers a system reset or
other corrective action if the main program, due to some
fault condition, such as a hang.
 The intention is to bring the system back from the
unresponsive state into normal operation.
 Usually it’s a count down timer.
 During normal operation, the
CPU regularly restarts the
watchdog timer to prevent it
from elapsing, or "timing out".
If due to a hardware fault or
program error, the computer
fails to restart the watchdog,
the timer will elapse and generate a reset signal to reset
the CPU.

6.Buses
 Physically, the bus consists of 8, 16 or more wire.
 There are two types of buses:
1. Address bus:
• unidirectional and carries the addresses of
memory locations indicating where the data is
stored into memory or read from memory.
• The number of wires in the address bus
determines the total number of memory locations.

6.Buses
2. Data Bus:
• bi-directional and carries information between the
CPU and memory or I/O devices.
• Computers are often classified according to the size
of their data bus. The term “8-bit microcontroller”
refers to a microcontroller with 8 lines on its data bus.
• The number of wires in the data bus determines the
number of bits that can be stored in each memory
locations.
3. control bus
• Carries commands from the CPU and returns status
signals from the devices.
• For Example: Memory chip READ/WRITE (R/W) lines
and Chip Select (CS) lines

6.Buses
150
 Example for 512 Bytes Memory
• Data Path Width = 4
• Address Path Width = 10
• Control lines
1. R/W
2. CS

7.Interrupts

7.Interrupts
 Basically events that require immediate attention by the
microcontroller.
 When an interrupt event occurs the microcontroller
pause its current task and attend to the interrupt by
executing an Interrupt Service Routine (ISR) at the
end of the ISR the microcontroller returns to the task it
had pause and continue its normal operations.

7.Interrupts
 Interrupt Service Routine (ISR) or Interrupt
Handler
• Piece of code that should be execute when an
interrupt is triggered. Usually each interrupt has its
own ISR. Its address in ROM is usually save in
interrupt vector table.
• should be deterministic and short as possible, as it
usually set a flag to a specific task indicating a certain
event is happened, or save small data in buffer.

7.Interrupts
 Interrupt Vector Table(IVT)
• Constant table in ROM.
• Special addresses with respect to CPU.
• Each interrupt has specific address in the interrupt
vector table for it’s ISR.
• This specific address should be programmed to have
the address of ISR of the corresponding interrupt.

7.Interrupts
Note : Handler = ISR = Code

7.Interrupts
Interrupt Vector Table
for ATmega16 µC

7.Interrupts
 What happens when an interrupt occurs?
1. The microcontroller CPU completes the execution of
the current instruction and stores the address of the
next instruction that should have been executed (the
contents of the PC), status register and all the CPU
registers are pushed onto the stack.
2. Microcontroller CPU jump to Interrupt Vector Table
to get the ISR address of the triggered interrupt.
3. The interrupt vector of the triggered interrupt (ISR
start address of this interrupt) is then loaded in the
PC(program counter) from the interrupt vector table
and the CPU starts execution from that point up until
reaches the end of the ISR.

7.Interrupts
4. The address that was stored on the stack in step 1 is
reloaded in the PC, status register and all the CPU
registers are popped from the stack.
5. The CPU then continue executing the main program.

7.Interrupts

7.Interrupts
 Interrupt Sources
• Hardware Interrupts
 Signal to a PIN like reset interrupt or external
interrupt.
 Timer Overflow Interrupt.
 Serial Port Interrupt.
 ADC Interrupt.
• Software Interrupts
 interrupts are commands given by the
programmer, such as the SWI instruction for the
Motorola µCs.

7.Interrupts
External interrupt pins in
Atmega16 µC

7.Interrupts
 Interrupt Types
• Maskable Interrupts
maskable interrupt can be disabled and enabled
Depends on global interrupt enable in processor
status register. And it May be :
 External interrupt from external pin.
 Internal interrupt from peripheral.
• Non-Maskable Interrupts
 non-maskable interrupts can not be disabled and
are always enabled.
 Usually it’s external interrupt like: reset interrupt.

7.Interrupts
 Status Register
• Contains flags represent the status of the last
operation to control the following instructions
• Flags as:
 Overflow flag
 Negative flag
 Zero flag
 Carry flag
 Half-carry flag
 Global Interrupt mask

7.Interrupts
 AVR CPU Interrupts
• The AVR provides several different interrupt sources.
• These interrupts and the separate reset vector each
have a separate program vector in the program
memory space.
• The lower the address the higher is the priority level.
RESET has the highest priority, and next is INT0 - the
External Interrupt Request 0.
• All interrupts are assigned individual enable bits to
which must be written a logic one together with the
Global Interrupt Enable bit in the Status Register in
order to enable the interrupt.
• Any Interrupt request is triggered by an event that
sets its corresponding interrupt flag.

7.Interrupts
 When ISR should be executed in AVR CPU?
166
Global Interrupt enable Module Interrupt enable Automatic Flag
Interrupt

7.Interrupts
 Interrupts Priorities
• Each interrupt has default priority by its location in
interrupt vector table.
• Some controllers provide more intelligent interrupt
controller which give interrupt priority level for each
interrupt.
• If two interrupts have a same priority level then the
rule to return to the default priority according to the
interrupt location in IVT.
• In AVR CPU the interrupts have priority in
accordance with their interrupt vector position. The
lower the interrupt vector address, the higher the
priority.

7.Interrupts
 Interrupt Nesting
• Ability to leave the current interrupt and serve another
interrupt.
• Usually done if global interrupt is enabled and this
interrupt has higher priority.
• In AVR CPU when an interrupt occurs, the Global
Interrupt Enable I-bit is cleared and all interrupts are
disabled. The user can write logic one to the
I-bit on software to enable interrupt nesting. All
enabled interrupts can then interrupt the current
interrupt routine. The I-bit is automatically set when a
Return from Interrupt instruction.

7.Interrupts

7.Interrupts
Interrupt processing context:
1. If it’s maskable interrupt :
 Check if global interrupt is enabled.
 Check if this module interrupt mask is enabled.
 Check if the automatic flag is set.
2. If another ISR is currently in service check the priority
level.
3. Save important context registers in special registers or
stack, like the following:
 PC
 Processor status register
 Accumulators
 General purpose register
4. Jump to ISR using vector table

7.Interrupts
 Interrupt latency is the time between the generation of
an interrupt by a device and the servicing of the device
which generated the interrupt.
 Interrupt latency may be affected by:
• Interrupt controllers.
• Interrupt masking.
• OS interrupt handling methods.

7.Interrupts
 Interrupt Response: Interrupt latency + Time to save
the CPU context.
 Interrupt Recovery: Is defined as the time required for
the processor to return to the interrupted code.

7.Interrupts
• In polling the MC asks the peripheral “Do you have any
data to process?” but in interrupts the peripheral says “I
got new data now, Process it” while the MC is working
on his normal task.
• Interrupts is usually a better solution than polling, but
sometimes the handling of this data takes time, in this
case we set a flag by the interrupt and the ordinary task
will poll on this flag, as checking on flag is much quicker
than checking on the peripheral status.

 Agenda
• Embedded HW

Micro-Controller other components
 Microcontroller may contain these
Peripherals:
• Analog Digital Converter(ADC).
• Analog Comparator.
• Universal Synchronous/Asynchronous Receiver
Transmitter(USART).
• Serial Peripheral Interface(SPI).
• Inter Integrated Circuits(I2C).
• Local Interconnect Network(LIN).
• Controller Area Network(CAN).
• EEPROM Memory.
• Direct Memory Access(DMA).
 Will be discussed later in Interfacing Course.

Micro-controller clock
 Clock signal is a particular type of signal that oscillates
between a high and a low state, Circuits use the clock
signal for synchronization may become active at either
the rising edge, falling edge, or, in the case of double
data rate, both in the rising and in the falling edges of the
clock cycle.
 Microcontroller clock generator source could be internal
or external.
 Microcontroller external clock sources could be RC
oscillator or Crystal oscillator but internal clock source
could by RC oscillator only.

Micro-controller clock(External sources)
179
Crystal oscillator RC oscillator

Micro-controller power
 Power Management features
A majority of microcontrollers usually support an
operation of 3 - 5.5 V. As consumer goods become
trendier, compact and lighter, the focus is on
microcontrollers to ensure that products with less power
usage are efficiently built and then used by end-users.
 How do we minimize power ?
1. Turn off unnecessary logic
2. Reduce memory accesses
3. Use sleep modes in unused controllers

 Agenda
• Embedded HW

Embedded Systems Constrains
 Constraints could be after that classified as
following :
• I/O constraints.
• Communication constraints.
• Operating Constraints.
• Memory Consumption.
• Microcontroller resources.

 I/O constrains:
any specification related to Digital inputs/outputs or
Analog inputs example:
1. Maximum and Minimum I/O values.
2. Rate of change.
3. Sampling rate.
4. Bit streams coding.
5. Baud rate.

 Communication constrains:
Constrains related to communication between
Microcontrollers and others blocks on boards Example:
• Communication protocol: SPI, UART, I²C, CAN.
• Specification of this protocol.
• May be specific Interface communication like MMC
Interface, SD memory Interface.

 Operating systems:
• Existence.
• Performance.
• Preemption.
• Static/dynamic task allocation.
 Maximum Execution time:
• Interrupts.
• Critical section.

 Memory consumption:
• RAM size
• ROM size
• Stack size
 Microcontroller constrains:
• Frequency
• Power modes
• CPU load

How to select a Micro-Controller
 Number of I/O ports.
 Peripherals required (Timers, ADC, USART,SPI and
EEPROM).
 Memory requirements.
 Maximum clock speed.
 Real-Time considerations.
 Number of interrupts required
 Power Consumption / sleep modes.
 Availability and Cost.
 Vendor Support.
 Development Environment.

Microcontroller Vendors
 Microcontroller Vendor is the manufacture of
the microcontroller chip it self.
188
Vendor Families Derivative
AVR ATmega16
8051 AT83EB5114
PIC PIC16F877A
V850 V850ES
HC12 MC9S12XEP100
TM4C TM4C123GH6PM

 Agenda
• Embedded HW

Embedded Systems Market

 The global market for embedded systems is expected to
increase from $92.0 billion in 2008 to an estimated
$112.5 billion by the end of 2013,
 Embedded hardware was worth $89.8 billion in 2008
and is expected to grow reach $109.6 billion in 2013
 Embedded software generated $2.2 billion in 2008,this
should increase to $2.9 billion in 2013

 Embedded market segmented the into HARDWARE and
SOFTWARE.
 The hardware segment consists of :
• Processor IP: MPU/MCU.
• DSP, ASIC, FPGA.
• Embedded boards.
 The software segment consists of:
• Operating Systems.
• Software Applications.
• Software development and testing tools.
• Linux-based operating systems and tools.

Embedded Systems Market in Egypt

Contact Details
Eng. Mohamed Tarek.
Embedded Software Engineer
Mob: 01115154316
Mail: mtarek.2013@gmail.com
My Embedded Diploma Contents
http://www.mediafire.com/download/94n11ai9ovo1xri/Embedde
d+Diploma+Contents.pdf

Introduction to Embedded Systems

More Related Content

What's hot (20)

Similar to Introduction to Embedded Systems (20)

Recently uploaded (20)

Introduction to Embedded Systems