IRJET- An Analysis of CMOS based Low Power 2:4 Decoder at 32nm Node using LECTOR Technique

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 12 | Dec 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 729
An Analysis of CMOS based Low Power 2:4 Decoder at 32nm node using
LECTOR Technique
Rajbeer Singh1, Manoj Kumar Bandil2
1PG Scholar, Department of Electronics & Communication, ITM Gwalior, India
2Assoc Professor, Department of Electronics & Communication, ITM Gwalior, India
-------------------------------------------------------------------------***------------------------------------------------------------------------
Abstract:- As the speed of shrinking and speed of operation of devices has escalated day by day more and more
functions are required to be embedded in a tiny piece of chip. Already power hungry circuits need extra power
to diminish their requirement especially the portable ones. As the voltage of operation is diminishing which
leads to rising of static power consumption due to rise in threshold leakage current caused by reduction of
threshold voltage. A new technique known as LECTOR technique has been implemented which can be used to
decrease leakage power without increasing overall dynamic power. LECTOR technique provides better option
than other alternatives due to its effectiveness in active and idle state. In this work we have designed CMOS 2:4
decoder with Lector Technique which significantly reduces the leakage power and improves the performance
of circuit in terms of power. We have worked on 32 nm node technology using 0.7V supply voltage with the
help of SPICE simulation tool.
Keywords - CMOS, 2:4 decoder, Leakage power, leakage current, LECTOR etc.
I. INTRODUCTION
As the electronic industry is booming at an explosion rate the most advanced devices does not get limited to
hands of some of the professionals or elite class of the society. Now everyone in the modern society from a kid
to elderly people holds an electronic device and the devices are becoming more and more portable to make its
availability convenient. High Power dissipation affects the battery life of portable device and hence the
reliability, packaging and heat sink costs. Hence power consumption is a major issue to address in modern
scenario of electronics [1]. The main types of power dissipation along with their origins are stated as:
 Dynamic power consumption which occurs when signals go through their transition due to switching on
and off of CMOS device.
 Short Circuit power consumption which occurs when CMOS makes transition and both NMOS along with
PMOS conduct simultaneously due to existence of conducting path between voltage supply and ground for a
fraction of time.
 Static power consumption: It is the leakage current which consists of:
a) Reverse Bias diode leakage current which occurs due to reverse biasing of drain and source to well
junctions.
b) Sub threshold leakage current is the current between source and drain of a transistor when transistor is in
sub threshold region which is gate to source below the threshold voltage.
c) Gate oxide tunneling leakage current prominent in nanometer scale which occurs due to tunneling of
carriers from bulk and source/drain overlap region through the gate oxide potential into the gate .
d) Gate induced drain leakage are the tunneling based leakage currents prominent in nanometer scale caused
where the gate overlaps the drain.
e) Gate leakage current due to hot carrier effect prominent in nanometer scale which is due to drift over time
of threshold voltage in short channel devices [2], [3].

Fig. 1 shows projections of the power consumption components of various years according to the
International Technology Roadmap for Semiconductors (ITRS).This projection clearly shows that as devices get
scaled down to nanometer scale static power consumption is expected to surpass the dynamic power
consumption. All the above mentioned mechanisms of static power leakage, subthreshold leakage current are a
major contributor in static power as the supply voltage has been scaled sown to keep dynamic power
consumption within limit [4], [5]. But to maintain high drive current capability threshold voltage has to be
scaled which results in exponential increase of subthreshold leakage currents [6].
Fig.1. Projection of the Power Consumption Component of various years [7].
In this paper we are studying the circuit of CMOS based 2:4 decoder using a new power saving technique.
Decoder are the integral parts of all the processing chips as they are used as address decoders in memory
systems, instructional decoders in CPU and also to activate particular set of output according to input data
combination as in binary decoders. Decoders have basically input as the counter output which transits to
activate a particular set of outputs. These outputs of decoder can be used to set particular device ON or OFF and
can be used as clocking signals. These are widely used in memory systems of computer where they address the
particular memory location depending upon the instruction by CPU [8]. Hence designing a power saving
decoder has an impact on every device in the digital universe as decoders are integral devices of digital
systems. A 2:4 Decoder has 2 inputs and 4 outputs along with an Enable signal. We analyse the parameters
leakage current, propagation delay and leakage power of the proposed circuit along with the conventional
CMOS circuit.
II. LECTOR TECHNIQUE
Scaling of technology following Moore’s Law is not a straight line as various trade-offs are to be made
between dynamic power consumption, static power consumption, propagation delay, area and cost has to be
made. As the devices are becoming more and more portable so the requirement of power efficient devices is
increasing day by day as the end of day it all depends on the battery life of devices. Static/Leakage power
dissipation is the main culprit as it eats the battery even when the device is not in use.
In the proposed work we have used a technique known as LECTOR (Leakage Control TransistOR) which
significantly reduces the static power consumption without influencing the dynamic power consumption
Year
NormalizedDynamic/Static
PowerDissipation
Energy per (W/L gate=3) Device
Switching Transition
Dynamic Power Dissipation per (W/L
gate =3) Device
Static Power Dissipation per
(W/L gate=3) Device

[9].The basic idea behind this technique is [10], [11] to have “A circuit with more than one transistor is off
between power supply to ground having less leaky than a circuit with only one transistor is off between power
supply to ground” [12]. We are showing LECTOR technique for general CMOS based gate circuits which
consists of PUN (pull up network) and PDN (pull down network).This technique can be extended to any CMOS
based gate circuit. In this circuit we have used two leakage control transistor (LCTs) between pull up network
and pull down network [13] such that one of LCTs is always near its cut off region of operation. As LCT1
(PMOS) and LCT2 (NMOS) are introduced between nodes N1 and N2.Both the drains of LCTs combined to form
output of CMOS circuit and their sources are connected to nodes N1 and N2 .Gates of both LCTs are cross
coupled to the source of other LCTs. Voltages at the nodes N1 and N2 control the switching of both the LCTs.
This feedback connection is such that whatever is the input at the gate, one LCTs is always near the cut off
region. These are designed in such a way that these are self controlled LCTs requiring no external circuit to
control them. Hence two LCTs increase the resistance between Vdd and ground reducing the leakage current.
This technique is superior to other power saving techniques such as power gating, sleepy transistor, zigzag
technique [14],[15],[16] etc as it does not require external circuitry to control them .The CMOS based Gate with
LECTOR technique is shown in Fig. 2.
Fig. 2.LECTOR based CMOS Gate
III. PROPOSED CIRCUIT
We have proposed 32 nm based CMOS 2:4 decoder using LECTOR technique.2:4 Decoder is a basic decoder
which can be used to build higher order decoders and it consists of two NOT gate and four AND gates. We have
introduced two LCTs transistor in each pull up network (PMOS) and pull down network (NMOS) .The proposed
circuit is shown in the Fig. 3.
LCT1
In2
LCT2
Vdd
In1 PUN
PDN
OUT
N2
N1

Fig.3. LECTOR based 2:4 CMOS Decoder
IV. RESULTS AND SIMULATION
The proposed LECTOR based 2:4 Decoder circuit was simulated using SPICE tools in 32 nm technology. Fig. 4
shows the output file of SPICE tool which reflects leakage power and leakage current of the circuit under study.
Fig. 5 shows the waveform obtained at the output which is in agreement of the input combinational data. In
Table 1, we have made comparison of power dissipation, leakage current and propagation delay between
CMOS based conventional 2:4 Decoder and LECTOR based 2:4 Decoder. Fig. 6 shows the graphical
representation of the decrease in power dissipation and leakage current along with increase in propagation
delay. It is evident from the results that LECTOR based 2:4 Decoder shows improvement over CMOS based
conventional 2:4 Decoder in terms of leakage power.

Fig.4. Output File of SPICE Tool of LECTOR based 2:4 Decoder
Fig.5. Output Waveform of LECTOR based 2:4 Decoder
Table 1: Comparison of Parameters of Conventional CMOS based 2:4 Decoder and LECTOR based 2:4 Decoder
Parameters CMOS based 2:4
Decoder 32nm
LECTOR based 2:4
Decoder 32nm
% Decrease in the
Leakage Power
% Increase in the
Propagation Delay
Supply
Voltage
0.7v 0.7v -- --
Leakage
Power
331.0987nw 115.0931nw 65.23% --
Leakage 472.9981nA 164.4188nA 65.23% --

current
Propagatio
n Delay
20.390ps 50.120ps -- 145.81%
Fig.6. Bar Graph showing reduction in Power Dissipation and Leakage Current
V. CONCLUSION
In this paper we have proposed CMOS based 2:4 decoder using LECTOR technique and the results we obtained
after performing simulation on 32 nm scale using SPICE tool are satisfactory. We have observed that power
dissipation and leakage current has reduced by using LECTOR technique as compared to conventional CMOS
2:4 decoder outperforming the rise in propagation delay. There is a 65.23% of improvement in power
dissipation of LECTOR based 2:4 Decoder as compared to conventional CMOS which overshadows the 145%
increase in propagation delay. LECTOR technique can be applied to complicated circuits where power efficiency
plays a major role. As we have performed simulation on 32 nm scale which can be extended to 22nm scale and
further down the nanometer scale to find the effect of LECTOR technique in controlling the leakage power.
REFERENCES
[1] P.Verma, R. A. Mishra, “Leakage power and delay analysis of LECTOR based CMOS circuits,” Int’l conf. on
computer & communication technology ICCCT 2011.
[2] B. Dilip, P. Surya Prasad & R. S. G. Bhavani, “Leakage power reduction in CMOS circuits using Leakage
control transistor technique in nanoscale Technology,” International Journal of Electronics Signals and Systems
ISSN: 2231- 5969, Vol-2 Issue-1, 2012.
[3] K.Roy, S. Mukhopadhyay, and H. Mahmoodi Meimad, “Leakage current mechanisms and leakage reduction
techniques in deep submicrometer CMOS circuits,” Proc. IEEE, vol.91, no.2, pp. 305-327, Feb. 2003.
[4] K.-S. Min, H. Kawaguchi and T. Sakurai, “Zigzag Super Cut-off CMOS (ZSCCMOS) Block activation with Self-
Adaptive Voltage Level Controller: An Alternative to Clock-gating Scheme in Leakage Dominant Era,” IEEE
International Solid-State Circuits Conference, pp. 400-401, February 2003.
[5] D. Duarte, Y.-F.Tsai, N. Vijay Krishnan, and M. J. Irwin, “Evaluating run-time techniques for leakage power
reduction,” in 7th Proc.ASP-DAC, 2002, pp.31-38.
[6] B. J. Sheu, D. L. Scharfetter, P. K. Ko, and M. C. Jeng, “BSIM: Berkeleyshort-channel IGFET model for MOS
transistors,” IEEE J. Solid-State Circuits, vol. SC-22, pp. 558–566, Aug. 1987.
0
50
100
150
200
250
300
350
400
450
500
Power Dissipation (nW)Leakage Current (nA)Propagation Delay (ps)
CMOS based 2:4 decoder
LECTOR based 2:4 decoder

[7] (2001) International Technology Roadmap for Semiconductors. International SEMATECH, Austin, TX.
[Online]. Available: http://public.itrs.net/
[8] A. Anand Kumar,“Fundamentals of Digital Circuits” Second Edition, Prentice Hall of India, pp.337-340, 2006.
[9] N. Hanchate and N.Ranganathan, “LECTOR: A Technique for Leakage Reduction in CMOS Circuits,” IEEE
Transactions on VLSI Systems, vol. 12, pp. 196-205, Feb. 2004.
[10] K. Nii, H. Makino, Y. Tujihashi, C. Morishima, Y. Hayakawa, H. Nunogami, T. Arakawa, H. Hamano,“A low
power SRAM using auto-backgate-controlled MT-CMOS, in Proceedings of the IEEE International Symposium
on Low Power Electronics and Design (ISLPED),” pp. 293–298 ,1998.
[11] J. Park, “Sleepy Stack: a New Approach to Low Power VLSI and Memory,” Ph.D. Dissertation, School of
Electrical and Computer Engineering, Georgia Institute of Technology, 2005.
[12] S. Thompson, P. Packan, and M. Bohr, “MOS scaling: Transistor challenges for the 21st century,” Intel
Technol. J., vol.Q3, 1998.
[13] A.Chandrakasan, I.Yang, C. Vieri, D. Antoniadis, “Design Considerations and Tool for Low-voltage Digital
System Design,” 334d Design Automation Confrence, pp 113-118, June 1996.
[14] M. C. Johnson, D. Somasekhar, L. Y. Chiou, and K. Roy, “Leakage control with efficient use of transistor
stacks in single threshold CMOS,” IEEE Trans. VLSI Syst., vol. 10, pp. 1-5, Feb. 2002.
[15] Q. Wang and S. Vrudhula, “Static power optimization of deep sub-micron CMOS circuits for dual V
technology,” in Proc. ICCAD, pp. 490–496, Apr.1998,.
[16] E. M. Sentovich, K. J. Singh, L. Lavagno, C. Moon, R. Murgai, A. Saldanha, H. Savoj, P. R. Stephan, R. K.
Brayton, and A.-S. Vincentelli.1992. SIS: A System for Sequential Circuit Synthesis (1992).

IRJET- An Analysis of CMOS based Low Power 2:4 Decoder at 32nm Node using LECTOR Technique

More Related Content

What's hot (20)

Similar to IRJET- An Analysis of CMOS based Low Power 2:4 Decoder at 32nm Node using LECTOR Technique (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- An Analysis of CMOS based Low Power 2:4 Decoder at 32nm Node using LECTOR Technique