Analysis Of Power Dissipation Amp Low Power VLSI Chip Design

Scientific Journal Impact Factor (SJIF): 1.711
International Journal of Modern Trends in Engineering
and Research
www.ijmter.com
@IJMTER-2014, All rights Reserved 89
e-ISSN: 2349-9745
p-ISSN: 2393-8161
Analysis of Power Dissipation & Low Power VLSI
Chip Design
Ms. Anshu N. Adwani1
, Mr. Hitesh V. Chopade2
, Prof. Swapnil S. Jain3
1, 2
M. Tech (Electronics & Communication Engineering),DMIETR, Wardha, Maharashtra, India.
3
Asst. Professor Electronics &Telecommunication Engineering, DMIETR, Wardha, Maharashtra,
India
Abstract—Low power requirement has become a principal motto in today’s world of electronics
industries. Power dissipation has becoming an important consideration as performance and area for
VLSI Chip design. With reducing the chip size, reduced power consumption and power management
on chip are the key challenges due to increased complexity. Low power chip requirement in the
VLSI industry is main considerable field due to the reduction of chip dimension day by day and
environmental factors. For many designs, optimization of power is important as timing due to the
need to reduce package cost and extended battery life. This paper present various techniques to
reduce the power requirement in various stages of CMOS designing i.e. Dynamic Power
Suppression, Adiabatic Circuits, Logic Design for Low Power, Reducing Glitches, Logic Level
Power Optimization, Standby Mode Leakage Suppression, Variable Body Biasing, Sleep Transistors,
Dynamic Threshold MOS, Short Circuit Power Suppression.
Keywords-Low power, VLSI, CMOS, package cost, battery life, power dissipation.
I. INTRODUCTION
In modern era VLSI design efforts have focused primarily on increasing the speed to realize
computationally intensive functions such as video compression, gaming &graphics etc. So, we have
semiconductor ICs that successfully integrated various complex signal processing modules &
graphical processing units to meet our requirement. While these solutions have addressed the real-
time problem, they haven’t addressed the demand for portable high speed operation, where mobile
phone needs to design with all this without consuming much power. The strict limitation on total
power dissipation in portable electronics applications like smart phones and tablet computers must be
met by the VLSI chip designer while still meeting the computational requirements. But wireless
devices are rapidly making their importance to the consumer electronics market; a key design
component for portable operation namely the total power consumption of the device must be
addressed. Lowering the total power consumption in these systems is important since it is desirable
to maximize the run time with minimum requirements on size, battery support and required weight of
batteries. So the most useful factor to consider while designing SOC for portable devices is 'low
power design'.[1]
II. PROBLEM ASSOCIATED WITH POWER DISSIPATION
Scaling of technology node increases power-density more than expected. CMOS technology
beyond 65nm node arises a real challenge for any sort of voltage and frequency scaling Starting from
120nm node, each new process has obvious higher dynamic and leakage current density with
minimum increase in speed. Between 90nm to 65nm the dynamic power dissipation is almost same

International Journal of Modern Trends in Engineering and Research (IJMTER)
Volume 02, Issue 01, [January - 2015] e-ISSN: 2349-9745, p-ISSN: 2393-8161
whereas there is ~5% higher leakage/mm2 [3]
.Low cost always require higher levels of integration,
whereas less costly technological breakthroughs to keep power under control are getting very scarce.
III. DO WE NEED TO BOTHER WITH POWER?
Power dissipation is the main look up when it comes to Portability. The mobile device
consumer keeps demanding more features and extended battery life at a lower cost. About 70% of
users require longer talk-time and maximum stand-by time as primary mobile phone feature. For 3G
technology we require more power efficiency, consumer also needs smaller size gadgets. It requires
high levels of Silicon integration in advanced processes, where as advanced processes have
inherently higher leakage current. So we must need to consider leakage current while designing low
power gadgets.
IV. WHY POWER MATTERS IN SOC?[4]
Power Management useful in System on Chip because of following concerns:
1. Packaging & Cooling costs.
2. Digital noise immunity,
3. Battery life of portable systems
4. Environmental issues.
V. SOURCES OF POWER DISSIPATION
The power dissipation in circuit is classified into three classes as described below.
1. Dynamic power consumption: Because of logic transitions causing logic gates to
charge/discharge load capacitance.
2. Short-circuit current: In a CMOS logic P-branch and N-branch are momentarily shorted as
logic gate changes state for short circuit power dissipation.
3. Leakage current:It occurs when the system is in standby mode or not powered. There are
various sources of leakage current in MOSFET[7]
. Diode leakages around transistors &n-wells,
Sub-threshold Leakage, Gate Leakage, Tunnel Currents etc. Increasing 20 times for each new
fabrication technology.
VI. LOW-POWER DESIGN TECHNIQUES
An integrated low power methods requires optimization at all design abstraction layers as below:
1. System: Partitioning, Power lowering.
2. Algorithm: Complexity in design, Concurrency of operation, Regularity in working.
3. Architecture: Parallelism of operations, Pipelining of processes, Redundancy of data, Data
Encoding & decoding.
4. Circuit Logic: Logic design Styles, Energy Recovery methods, component sizing.
5. Technology: Threshold Reduction capability, Multi Threshold Devices.
Dynamic power varies as VDD2. So lowering the supply voltage reduces power dissipation.
The selective frequency reduction technique used to lower the dynamic power requirement[4]
. At
system level, multi threshold voltage can be used to reduce leakage power. For speed-up circuit and
reduce power transistor resizing can be used. Sleep transistors can be used efficiently to reduce
standby power. Parallel processing and pipelining can reduce power requirement. Clock disabling,
power-down of selected logic blocks, adiabatic computing, software redesign to lower power
dissipation are the other techniques commonly used for low power design.

VII. VLSI CIRCUIT DESIGN FOR LOW POWER
The growing market of portable gadgets (cellular phones, gaming remotes) battery-powered
electronic systems require microelectronic circuits design havingultra-low power dissipation. As the
integration, size, and complexity of the chips continue to increase, the difficulty in providing
sufficient cooling might either add significant cost or limit the functionality of the computing
systems which make use of those integrated circuits. The technology node scales down to 65nm there
is not much increase in dynamic power dissipation. However the static power or leakage power is
same as or exceeds the dynamic power below 65nanometer technology node.
So themethods to reduce power dissipation is not limited to dynamic power. In this paper we
approaches to minimize Dynamic, Leakage power dissipation and Short Circuit power dissipation.
Power minimization in a processor can be achieved at various levels of designing. So we need to
optimize or reduce the power requirement of desired circuitry[3]
.
Total Power dissipated in a CMOS circuit is equal to total of dynamic power, short circuit
power and static power or leakage power. Designed structure for low-power requirement implies the
ability to reduce all three parameters of power consumption in CMOS circuits during the designing
of a low power electronic product.
Figure 1.Components of Power in CMOS circuit Ptotal = CLVDD2 + tscVDDIpeak + VDDIleakage
7.1. DYNAMIC POWER SUPPRESSION
Dynamic/Switching power is due to charging and discharging of load capacitors driven by
the circuit. Supply voltage variation has been the most preferred approach to power optimization,
since it normally result in considerable power savings due to the quadratic dependence of
switching/dynamic power PSwitching on supply voltage VDD. However limiting the supply voltage
affects circuit speed which is the major short-coming of this method. So design and technological
solutions must be applied to compensate the decrease in circuit performance introduced by reduced
voltage. Some of the methodology often used to reduce dynamic power are described below.
7.2. ADIABATIC CIRCUITS
In adiabatic circuits instead of dissipating the power is reused. By externally limiting the
length and shape of signal transitions energy spent to flip a bit can be reduced to very small values.
As the diodes have thermodynamic irreversible nature they are not used in the design of Adiabatic
Logic. MOSFETs should not be switched ON when there is significant potential difference between
source and drain. And shouldn’t be TURNOFF when there is a significant current flowing through
gadget.

Figure 2.Charge Recovery Logic
7.3. LOGIC DESIGN FOR LOW POWER
Selection between static & dynamic topologies, conventional CMOS &pass-transistor logic
styles and synchronous & asynchronous timing styles have to be made while designing a circuit. In
static CMOS circuits, about 10% of total power consumption is due to short circuit current.
However, in dynamic circuits there is small amount of power dissipation to reduce the sharing, as
there is no direct dc path between GND & power supply.[6]
Figure 3. (a) Static NOR circuit Figure 3(b) Dynamic NOR circuits
We alsouse pass transistor logic to exploit reduced swing to lower power.
Figure 4. Pass Transistor Logic, P = CL* Vdd* (Vdd-Vt)
7.4. REDUCING GLITCHES
Glitches generates in a logic chain when two parallel driving common gate approaches at
different times. The output instantly switches to incorrect value before settling to correct value.
Consider circuit shown below. consider that in the absence of buffer path A is high speed and Path B
is slow. At begining if A=0 and B=1 then Z=0.Next if B switched to 0 and A to 1 as B is slow the
data 0 arriving at B will be slow and hence Z switches towards 1 for small time before switching
back to 0 resulting in unnecessary power dissipation.
Figure.5. Glitch Free AND Gate

7.5. LOGIC LEVEL POWER OPTIMIZATION
During logical design implementation for low power, technology parameters like supply
voltage are of fixed value, and availability for selecting the functionality and sizing the gates.
Equalizing the path & insertion of buffer is one of the techniques which make sure that signal
propagation from inputs to outputs of a logic network follows paths of similar length to overcome
glitches. When paths are equalized, there is equal delay for each branch which result in less delay
while feeding signal to next node.
Figure 6. Logic Remapping of design for Low Power[4]
7.6. STANDBY MODE LEAKAGE SUPPRESSION
Static power & Leakage powergenerated from substrate currents and sub-threshold leakages.
For technologies 1 µm and above, PSwitching was more dominant. But for deep-submicron processes
below 180nm, PLeakage becomes dominant parameter. Leakage power is a major issue in recent
technologies, as it impacts battery lifecycle & battery life. CMOS technology has been most power-
efficient when transistors are not switching or in stand-by mode, and system manufacturer expect
low leakage from CMOS IC chips. To meet leakage power parameters, multiple-threshold and
variable threshold circuit techniques are frequently used. In multiple-threshold CMOS, the process
provides two different threshold transistors. Low-threshold is employed on speed-critical sub-circuits
and there are fast and leaky. High-threshold transistors are of low speed but exhibit low sub-
threshold leakage, and they are results in noncritical or slow paths of the chip.
7.7. VARIABLE BODY BIASING
Threshold voltage of transistors can be dynamically control by variable-threshold through
substrate biasing and hence overcome shortcoming associated with multi-threshold design. When a
variable-threshold circuit is on standby mode, the substrate of NMOS transistors is negatively biased,
and their threshold increases due to effect of body-biasingt. Also the substrate of PMOS transistors is
biased by positive body bias to increase their Vt in stand-by mode.[5]
Variable-threshold require
control circuits that modulate substrate voltage in stand-by mode. When the circuit is in standby
mode the bulk/body of both PMOS and NMOS are biased by third supply voltage to increase the Vt
of the MOSFET as shown in the Figure. But in normal operation they are switched back to reduce
the Vt.
Figure 7. Variable Body Biasing

7.8. SLEEP TRANSISTORS
When High Vt transistors connected in series with low Vtlogic as shown below are termed as Sleep
Transistor.When Low Vt devices are ON the sleep transistors are also ON resulting in normal
operation of the circuit. When the circuit is in Standby mode, HighVttransistors are OFF. As High Vt
devices are in series with Low Vt circuit the leakage current is calculated by High Vt devices and is
less, thus reduced the power dissipation.
Figure 8. Sleep Transistors Circuit Design
7.9. DYNAMIC THRESHOLD MOS
In dynamic threshold CMOS (DTMOS), the threshold voltage is altered dynamically to suit
the operating state of the circuit. For low leakage current we use high threshold voltage in the
standby mode & a low threshold voltage gives higher current drives in the active mode of operation.
CMOS with dynamic threshold characteristic can be obtained by joining the gate and body with
each other. The supply voltage of DTMOS is restricted by the diode built-in potential in bulk silicon
technology. The PN diode between source and body must be reverse biased. So, this technique is
only preferred for ultralow voltage (0.6V and below) circuits in bulk CMOS.
Figure 9. DTMOS Circuit
7.10. SHORT CIRCUIT POWER SUPPRESSION
Short circuit currents that comes into consideration when pairs of PMOS/NMOS transistors
are conducting simultaneously resulting in Short circuit power.
Figure 10. Short Circuit Power in CMOS Circuits

One way to reduce short circuit power is to keep the input and output rise/fall times the same.
If the load capacitance is greater, so the output fall time is larger than the input rise time. The drain-
source voltage of the PMOS transistor is 0. So the short-circuit power is 0. If the load capacitance is
of less capacitance, the output fall time is less than the input rise time. For PMOS transistor the
drain-source voltage is nearer to VDD during most of the transition period. Therefore we obtain large
short circuit current.
VIII. CONCLUSION
The need for lower power systems is being driven by many market segments. Unfortunately
designing for low power adds another dimension to the already complex design problem and the
design has to be optimized for power as well as Performance and Area.
REFERENCES
[1] T. Burdet et.al, “Low power VLSI design”, Journal of VLSI Signal Processing Systems, vol.13, no. 2-3, pp.
203-221, August 1996.
[2] Jingjing Fu, Zuying Luo, Xianlong Hong, Yici Cai, Sheldon X.-D. Tan, Zhu Pan, “VLSI On-Chip
Power/Ground Network Optimization Considering Decap Leakage Currents” ASP-DAC 2005 page no 735-738.
[3] S. Y. Zhao, K. K. Roy, C. K. Koh. “Decoupling capacitance allocation for power supply noise suppression”
ISPD2001, Sonoma, 2001: 66-71.
[4] Kanika Kaur and Arti Noor “STRATEGIES & METHODOLOGIES FOR LOW POWER VLSI DESIGNS: A
REVIEW” International Journal of Advances in Engineering & Technology, May 2011.IJAET ISSN: 2231-
1963 Vol. 1,Issue 2,pp.159-165.
[5] Shekar Borkar, "Design Challenges of Technology Scaling," IEEE Micro, July/August 1999, pg 23.
[6] Y. Yeo, et.al, “Direct Tunneling Gate Leakage Current in Transistors with Ultrathin Silicon Nitride Gate
Dielectric,” IEEE Electron Devices Letters, vol.21, no.11, pp. 540-542, Nov.2000.
[7] Shinichiro Mutoh, Yasuyuki Matsuya , Takahko Aoki and Junzo Yamada “1-V Power Supply High-speed
Digital Circuit Technology with Multi-threshold-Voltage CMOS”, IEEE, vol. 30, August 1995, pp.847-848.
[8] Se-Joong Lee, “Adaptive Control Methodology for High-performance Low-power VLSI Design”, Frontiers in
Adaptive Control, Shuang Cong (Ed.), ISBN: 978-953-7619-43-5.

Analysis Of Power Dissipation Amp Low Power VLSI Chip Design

Analysis Of Power Dissipation Amp Low Power VLSI Chip Design

More Related Content

Similar to Analysis Of Power Dissipation Amp Low Power VLSI Chip Design (20)

More from Bryce Nelson (20)

Recently uploaded (20)

Analysis Of Power Dissipation Amp Low Power VLSI Chip Design