IRJET- Array of Circular Microstrip Patch Antenna
0 likes90 views
The document presents the design of a 1x4 circular microstrip patch antenna array operating at 3.5GHz. Circular patch antennas were chosen for their improved gain, return loss, and bandwidth. The antenna array was designed and simulated using IE3D software, and was found to have a return loss of -22.5dB and a gain of 4.52dBi, demonstrating an improvement over a single circular patch antenna.
![International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3922
(7)
I. 1x4 ANTENNA ARRAY
Fig 1:1x4 antenna array
Fig 1 is the antenna array design of 1x4 arrays.It consists
of 4 circular patch antennas with inset feed technique
designed on FR4 substrate.
Fig 2: Return loss
The above figure shows the return loss of 1x4 antenna
array.The return loss of -22.5dB is obtained at 3.5 GHz.The
desired return loss for the antenna must be less than -10dB.
Fig 3: Gain
Fig 3 shows the graph of gain v/s frequency. Gain is an
important parameter of an antenna that defines the total
power which is radiated in a particular direction. The unit
of gain is dBi. The gain of 4.52dBi is obtained.
3. CONCLUSIONS
Accordingly we have designed 1x4 microstrip patch array
antenna at 3.5GHz frequency. Several antenna parameters
like gain and return loss are obtained. The obtained gain is
4.52dBi, which we can see is comparatively greater than the
single patch. The single patch antennas give gain of 2-3dBi.
The return loss obtained is -22.5dB.The results give
satisfactory performance. Hence we can conclude that 1x4
antenna improves the gain and the performance of the
antenna.
REFERENCES
[1] Microstrip Patch Antenna Array Design to Improve
Better Gains Vasujadevi Midasala1 , Dr. P. Siddaiah2 1
Research Scholar, JNTUA, Ananthapuramu, Andhra
Pradesh, India 2 Professor & Principal, University
College of Engineering & Technology, Acharya
Nagarjuna University, Guntur
[2] Rakhi and Sonam Thakur, “Performance Analysis of
Different Shapes Patch Antennas at 2.45 GHz”,
International Journal of Engineering Research and
Technology, Vol.3, Issue 9, 2014
[3] A.R.G.Chandra Mouli.K, DrM. Satya Anuradha,Darshana
Kuppili,Dattatreya Gopi A.R.G.CHANDRA MOULI.K,
“Analysis of Rectangular and Triangular Microstrip
Antenna Arrays using HFSS”, 2015 13th International
Conference on Electromagnetic Interference and
Compatibility (INCEMIC)
[4] Madhukant Patel, Piyush Kuchhal, Kanhiya Lal, Ranjan
Mishra, “Design and Analysis of Microstrip Patch
Antenna Array using Different Substrates for X-Band
Applications”, International Journal of Applied
Engineering Research ISSN 0973-4562 Volume 12,
Number 19 2017
[5] Mohini Narendra naik, H.G.Virani, “Design and
simulation of array of rectangular slotted microstrip
patch antenna with improved bandwidth for
WLAN”,IEEE 2016.](https://image.slidesharecdn.com/irjet-v6i41209-190730062113/85/IRJET-Array-of-Circular-Microstrip-Patch-Antenna-2-320.jpg)
IRJET- Array of Circular Microstrip Patch Antenna
- 1. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072 © 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3921 Array of circular microstrip patch antenna Urwashi Vithal Miringkar1, Asst.Prof.Palhavi Kerkar2 1Electronics And Telecommunication-Industrial Automation And Radio Frequency, Goa College of Engineering 2Electronics and Telecommunication, Goa College of Engineering ---------------------------------------------------------------------***--------------------------------------------------------------------- Abstract - This paper presents the array of circular microstrip patch antenna. The element of the antennais 1x4 arrays. The antenna operates at 3.5GHz.Circular antennas give good return loss, and better gain and directivity. The main aim of using thearrayistoimprove the gain of the antenna. Inset feed technique is used to design the antenna. The size and feed technique is determined by design formulas. Ie3d software isusedfor simulation. Key Words: Antenna array; directivity; Microstrip patch; 1.INTRODUCTION Several antennas are arranged and connected in regular structure to form single antenna. There are various types of antenna array i.e, Log periodic dipole array, planar array, collinear array, and phased array. Phased array antenna consists of multiple antenna system, in which, that the radiation pattern can be reinforced in a desired direction & suppressed in undesired directions. The phased array antennas are now widely used, and are spreading to civilian applications. Phased arrays are used by many AMbroadcast radio stations to enhance signal strength and therefore, minimizes interference to other areas. Antenna arrays are widely used because it increases the radiated power and provide high directional beam which avoids power loss in other directions. Basically the arrays are used to improve the radiation pattern. Arrays increase the directivity of the antenna and provides electronic steering which eliminates the use of mechanical steering using servo motor. And hence beam can be moved in less than millisecond. Arrays are also used for tracking in radar and surveillance. Configuration of array is simple arrangement of elements. There are various types of structures available for microstrip patch, such as rectangular,circular,triangle,square,outofwhichcircularhas more advantages improved gain,return loss,easy designand improved bandwidth.Circular antennas also provides the flexibility of designing the the arrays. Circular Patch antennas can be designed to have horizontal,vertical left hand circular or right hand circular polarization, with multiple feeding points, or a singlefeed point. Suchantennas are common in airplanes and military applications because of its ability to give high gain in low profile antennas. The basic information about the circular antenna and the arrays has been described in the introduction.The first part consists of the design parametersandtheantenna design.the later section describes the result and conclusion. 1. ANTENNA DESIGN We have designed a patch antenna array consisting of FR4 substrate.3.5GHz is the resonant frequency of the antennaarray.FR4substratehas4.4relativepermittivity. The loss tangent for FR4 is 0.02 and thickness is 1.6mm. A circular patch is designed of radius 12mm, and 1x4 array is designed using one circular element. Following are the formulas to find the radius of the circular patch. (1) (2) (3) Inset feed techniqueisusedwhiledesigningthisantenna. The dimensions of the line feed are 25.8mm width and 3mm is the length which iscalculated using the required formulas. (4) (5) (6)
- 2. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072 © 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3922 (7) I. 1x4 ANTENNA ARRAY Fig 1:1x4 antenna array Fig 1 is the antenna array design of 1x4 arrays.It consists of 4 circular patch antennas with inset feed technique designed on FR4 substrate. Fig 2: Return loss The above figure shows the return loss of 1x4 antenna array.The return loss of -22.5dB is obtained at 3.5 GHz.The desired return loss for the antenna must be less than -10dB. Fig 3: Gain Fig 3 shows the graph of gain v/s frequency. Gain is an important parameter of an antenna that defines the total power which is radiated in a particular direction. The unit of gain is dBi. The gain of 4.52dBi is obtained. 3. CONCLUSIONS Accordingly we have designed 1x4 microstrip patch array antenna at 3.5GHz frequency. Several antenna parameters like gain and return loss are obtained. The obtained gain is 4.52dBi, which we can see is comparatively greater than the single patch. The single patch antennas give gain of 2-3dBi. The return loss obtained is -22.5dB.The results give satisfactory performance. Hence we can conclude that 1x4 antenna improves the gain and the performance of the antenna. REFERENCES [1] Microstrip Patch Antenna Array Design to Improve Better Gains Vasujadevi Midasala1 , Dr. P. Siddaiah2 1 Research Scholar, JNTUA, Ananthapuramu, Andhra Pradesh, India 2 Professor & Principal, University College of Engineering & Technology, Acharya Nagarjuna University, Guntur [2] Rakhi and Sonam Thakur, “Performance Analysis of Different Shapes Patch Antennas at 2.45 GHz”, International Journal of Engineering Research and Technology, Vol.3, Issue 9, 2014 [3] A.R.G.Chandra Mouli.K, DrM. Satya Anuradha,Darshana Kuppili,Dattatreya Gopi A.R.G.CHANDRA MOULI.K, “Analysis of Rectangular and Triangular Microstrip Antenna Arrays using HFSS”, 2015 13th International Conference on Electromagnetic Interference and Compatibility (INCEMIC) [4] Madhukant Patel, Piyush Kuchhal, Kanhiya Lal, Ranjan Mishra, “Design and Analysis of Microstrip Patch Antenna Array using Different Substrates for X-Band Applications”, International Journal of Applied Engineering Research ISSN 0973-4562 Volume 12, Number 19 2017 [5] Mohini Narendra naik, H.G.Virani, “Design and simulation of array of rectangular slotted microstrip patch antenna with improved bandwidth for WLAN”,IEEE 2016.