K to 12 fish processing learning module

K to 12 Basic Education Curriculum
Technology and Livelihood Education
Learning Module
FOOD (FISH)
PROCESSING
EXPLORATORY COURSE
Grades 7 and Grade 8
Republic of the Philippines
DEPARTMENT OF EDUCATION

FOOD (FISH) PROCESSING 1
K to 12 – Technology and Livelihood Education
TABLE OF CONTENTS
What Is This Module About ?................................................................................... 6
How Do You Use This Module ............................................................................... 7
LESSON 1 – Use food processing tools, equipment and utensils ..................9-31
LESSON 2 – Perform Mathematical Computations ..................................... 32-72
LESSON 3 – Interpret Plans and Drawings ................................................. 73-100
LESSON 4 – Apply Food Safety and Sanitation ........................................ 101-121
ANSWER KEYS ............................................................................................ 122-130
Acknowledgment.....................................................................................................131

Welcome to the world of Food (Fish) Processing!
This Module is an exploratory course which leads you to Food (Fish) Processing
National Certificate Level II ( NC II)1
. It covers 4 common competencies that a Grade 7 /
Grade 8 Technology and Livelihood Education (TLE) student like you ought to possess,
namely:
1) Use food processing tools, equipment and utensils;
2) Perform mathematical computations;
3) Interpret plans and drawings; and
4) Apply food safety and sanitation
These 4 common competencies are covered separately in 4 Lessons. As shown
below, each Lesson is directed to the attainment of one or two learning outcomes:
These 4 common competencies are covered separately in 4 Lessons. As shown
below, each Lesson is directed to the attainment of one or two learning outcomes:
Lesson 1 – Use Food Processing Tools, Equipment and Utensils
LO1. Select tools, equipment and utensils
LO2. Use tools, equipment and utensils following standard procedure
LO3. Perform post-operational activities
Lesson 2 – Perform Mathematical Computations
LO1. Gather and tabulate the recorded data relevant to processed food production.
LO2. Review various formulations
LO3. Calculate the production input and output.
LO4. Compute the costs of production.
Lesson 3 – Interpret Plans and Drawings
LO1. Interpret lay-out plan.
LO2. Perform outer packaging procedures.
Lesson 4 – Apply Hygiene and Sanitation
LO 1. Observe personal hygiene and good grooming
LO 2. Implement food safety practices
LO 3. Conduct work in accordance with environmental policies and procedures
LO 4. Participate in improving environmental practices at work
Your success in this exploratory course on Food (Fish) Processing is shown in your
ability to perform the performance standards found in each learning outcome.
1NATIONAL CERTIFICATE (NC) is a certification issued to individuals who achieved all the required units of competency for a national
qualification as defined under the Training Regulations. NCs are aligned to specific levels within the PTQF. (TESDA Board Resolution
No. 2004-13, Training Regulations Framework)
NATIONAL CERTIFICATE LEVEL refers to the four (4) qualification levels defined in the Philippine TVET Qualifications Framework
(PTQF) where the worker with:
a. NC I performs a routine and predictable tasks; has little judgment; and, works under supervision;
b. NC II performs prescribe range of functions involving known routines and procedures; has limited choice and complexity of
functions, and has little accountability;
What Is This Module About?

This Module has 4 Lessons. Each Lesson has the following parts.
 Learning Outcomes
 Performance Standards
 Materials
 References
 Definition of Terms
 What Do You Already Know?
 What Do You Need to Know?
 How Much Have You Learned?
 How Do You Apply What You Learned?
 How Well Did You Perform?
 How Do You Extend Your Learning?
To get the most from this Module, you need to do the following:
1. Begin by reading and understanding the Learning Outcome/s and Performance
Standards. These tell you what you should know and be able to do at the end of this
Module.
2. Find out what you already know by taking the Pretest then check your answer
against the Answer Key. If you get 99 to 100% of the items correctly, you may
proceed to the next Lesson. This means that you need not go through the Lesson
because you already know what it is about. If you failed to get 99 to 100% correctly,
go through the Lesson again and review especially those items which you failed to
get.
3. Do the required Learning Activities. They begin with one or more Information
Sheets. An Information Sheet contains important notes or basic information that you
need to know.
After reading the Information Sheet, test yourself on how much you learned
by means of the Self-check. Refer to the Answer Key for correction. Do not hesitate
to go back to the Information Sheet when you do not get all test items correctly.
This will ensure your mastery of basic information.
4. Demonstrate what you learned by doing what the Activity / Operation /Job Sheet
directs you to do.
5. You must be able to apply what you have learned in another activity or in real life
situation.
6. Accomplish the Scoring Rubrics for you to know how well you performed.
Each Lesson also provides you with references and definition of key terms for your guide.
They can be of great help. Use them fully.
.
How Do You Use This Module?
If you have questions, ask your teacher for assistance.

Use Food Processing Tools, Equipment and Utensils
LESSON 1
LO2. Use tools, equipment and utensils following standard
procedure
LO3. Perform post-operational activities
LEARNING OUTCOMES:
At the end of this Lesson you are expected to
do the following:

Assemble - means to gather or collect things together in one place.
Calibrate – means to set or determine the accuracy of the measuring device.
Check - is to examine something in order to establish its state or condition.
Dimension - is the measurement of the size of an object in terms of length, width, or height.
Equipment – things which are used to provide specific service or function.
Sanitize - means to clean something thoroughly by disinfecting or sterilizing to make it free
from germs or microorganisms; disinfect.
Sanitation - refers to the process of treating tools, equipment, and utensils with physical and
chemical sanitizing agents to kill residual microorganisms present after cleaning.
Disinfect - means to rid of germs; to clean something so as to destroy disease – carrying
microorganisms and prevent infection.
Specification – is a detailed itemized description of dimension plans, materials and other
requirements.
Standard – is a basis of comparison or established criterion.
Stowing – means arranging compactly or packing.
Brine solution - a solution of salt and water.
Brochure - a pamphlet
Catalogue - a systematic arrangement of listed items giving descriptive details.
PPT - parts per thousands
Standard - an authorized unit of weight or measure.
Operate – to make equipment function or work correctly.
Disinfect – to rid of germs; to clean something so as to destroy disease-carrying
microorganisms and prevent infection .
Tools - are implements used by hand when doing an activity or work. These are devices for
doing work or objects designed to do a particular kind of work, for example cutting or
chopping, by directing manually applied force or by means of a motor.
Conformity – the behavior that agrees with the accepted or conventional standards.
Breakdown – is mechanical failure causing a machine or equipment to malfunction.
Definition of Terms

Check – to test the accuracy; to examine something in order to establish its state or
condition.
Capacity - refers to the measurement of the amount which a device can hold or contain.
Corrosion – rusting or gradual wearing of machine parts due to a chemical reaction
between substances like iron and oxygen or other corrosive materials like salt, acids, etc.
Crack – a break or fissure on some parts of an equipment as in the body of a pressure
cooker.
Electrocution – death or execution from electric shock.
Inspect – to carefully examine a machine or equipment in order to determine maintenance
to undertake.
Leak – a crack or hole through which a liquid or gas may accidentally pass.
Lubricant – a substance like oil or grease that coats or treats a machine to lessen friction
and the wear and tear of machine parts due to constant rubbing of surfaces.
Preventive Maintenance – a system of maintenance that aims to minimize or eliminate
breakdown in equipment and machinery by a program of regular inspection and repairs.
Repairs – to restore a machine or equipment that breaks down into good order or condition.
Switch – electrical device having two (2) states, ON (closed) OFF (open).
Switch – off – to turn off an electrical device.
Stow – to pack or store in an orderly way.
Troubleshooting – systematic approach to locate the cause of a fault in an electronic circuit
or system.
Utensil – is an implement especially for use in the kitchen.

Select tools, equipment and utensils
LEARNING OUTCOME 1
1. Appropriate tools, equipment and utensils are selected according to food
(fish) processing methods.
2. Faults and defects of tools, equipment and utensils are explained.
3. Defective tools, equipment and utensils are reported in accordance with
farm procedures.
PERFORMANCE STANDARDS

Let us determine how much you already know about Lesson 1
Take this test.
Read and understand the questions below. Select the best answer for each item then write
your choice on your answer sheet. Do not write anything in the Module.
1. A device used to measure the strength of brine solution is
a. salinometer
b. thermometer
c. both a and b
d. refractometer
2. What is the function of the refractometer?
a. Measures the sugar content of sap and syrup
b. Measures the temperature of the food / fish
c. Wraps the food / fish for processing
d. All of the above
3. What is used in measuring the volume of liquid?
a. Salinometer
b. Cylinder
c. Refractometer
d. Thermometer
4. A standard measuring instrument used in fish processing is
a. Salinometer
b. Refractometer
c. Thermometer
d. All of the above
5. What type of water is used in calibrating the refractometer?
a. Distilled water
b. Sea water
c. Water from the faucet
d. Brackish water
6. A device used to measure the temperature of fish / food is
a. Thermometer
b. Salinometer
c. Refractometer
d. Beaker
What Do You Already Know?
Pretest LO 1
Let us determine how much you already know about the selecting food (fish)
processing tools, equipment and utensils. Take this test.

7. A device used to measure the weight of fish / food is
a. Thermometer
b. Weighing scale
c. Measuring cup
d. Measuring spoon
8. How many drops of sap or syrup sample are needed in testing the refractometer?
a. one
b. two
c. three
d. four

Equipment, Tools and Utensils: Uses of Specifications
Every equipment, tool and utensil that are purchased are accompanied with a
manual containing specifications as to how they are used, manipulated or operated, cared
for and stored to lengthen their serviceability. Specifications usually include the following:
1. Important safeguards or basic safety precautions to follow when using the device
like a pressure cooker for instance.
2. Warning labels which serve as a reminder to the user to read and follow
instructions on the proper use and operation of a certain device equipment or
tool.
3. Dimensions, weights and capacities as in the case of cookers, boilers and
steamers.
4. Instructions on caring for the equipment, tool or utensil.
5. Instructions on the correct usage of the device.
When using any equipment, tool or device it is important to read and understand the
manufacturer’s specifications in order to properly or accurately use or manipulate them and
prevent any accident that may occur due to ignorance or lack of information pertaining to
their correct usage. Being familiar with all information pertaining to food processing
equipment results to systematic, orderly and accurate accomplishment of tasks.
Parts and Functions of Equipment, Tools and Utensils
Knowing the parts and functions of equipment, tools and utensils used in processing
food ensures accurate or proper use, operation and care for them. It is very easy for a food
processor to manipulate a particular device if he knows all its parts and their respective
functions. Proper maintenance for the parts of any tool, equipment and utensil can also be
done if a processor is familiar with them.
What Do You Need To Know?
Read the Information Sheet 1.1 very well then find out how much you can
remember and how much you learned by doing Self-check 1.1.
Information Sheet 1.1

The Can Sealer
The can sealer is an equipment used to seal tin cans with its first and second
operation rolls.
Some processed food products are usually packed in tin cans which are
mechanically sealed with a can sealer. Below are the functions of some parts of an
automatic can sealer:
1. Clamp. This fastens the sealer on the table or arm chair and holds it tightly in place,
especially during operation.
2. Base plate or plunger plate. Its function is to hold the base of the can. It has
grooves to fit the can base wherein these grooves coincide the can size.
3. Can lifter handle. It is used to raise the base plate so that the can cover will reach
up to the chuck and lower the base plate so that the can cover will reach up to the
chuck and lower the base plate when sealing is through.
4. Crank. This part is turned during the sealing of can seams both first and second
operation rolls.
5. First operation roll. It is used to clinch, partially or half – seal the seams of a can
cover.
6. Second operation roll. It is used to complete – seal the seams of a can cover.
7. Seaming roller pin – first. It is placed on the hole of the first operation roll to fasten
on it.
8. Seaming roller pin – second. It is placed on the hole of the second operation roll to
fasten on it.
9. Rivet. This part is placed in the hole of the adjusting lever which coincides the can
cover size. If can cover size is No. 2, for instance, one – half pound tuna can rivet is
placed in No. 2 hole of the adjusting lever. Rivet is also called adjusting pin.
10. Chuck. It is used to hold the cover of the can while sealing is going on. Chuck has
many sizes, namely Number 1, 2, 2 ½, and 3, respectively. If No. 2 cover is used,
hence, hence, chuck No. 2 is used.
11. Height washers. These washers are placed in base plate shaft to match the height
of the can when lifted up to the chuck.
12. Adjusting levers. There are two adjusting levers, one for the first operation roll and
the other, second operation roll. There are numbered holes on these levers wherein
rivets are placed to coincide the can size.

13. Base compression spring. It acts as cushion while sealing is on the process.
14. Base plate shaft. This is the part where compression spring and height washers are
inserted.
The Pressure Cooker
A pressure cooker is an important canning equipment used to process fish packed in
a hermetically sealed container at a high controlled temperature and pressure for a certain
period of time. Some of its parts and their functions are as follows:
1. Geared seam gauge or pressure gauge. It indicates the pressure and
temperature inside the cooker while processing.

2. Pressure regulator weight. It is used to close the vent pipe and regulate the
accumulated pressure inside the cooker while processing. It contains holes
which correspond to the desired pressure directly over the vent pipe. For
instance, if the desired pressure is 10 pounds, the pressure regulator weight hole
of 10 is inserted over the vent pipe.
3. Vent pipe for pressure regulator weight. It is where the pressure regulator
weight is placed. It releases steam when opened.
4. Bakelite wingnut or knob. It is used to securely fasten the cover of the cooker
to its body.
5. Arrowhead and arrowline. They indicate if the cover is properly seated on the
body.
6. Automatic pressure control. It consists of the vent pipe and pressure regulator
weight. It automatically controls the pressure inside the cooker while processing.
7. Overpressure plug. It automatically vent or release steam if the vent pipe
becomes clogged.
8. Cover. Seals the body of the cooker during processing.
9. Body. It holds the water for processing and the metal rack where the canned
products are placed during processing.
10. Bakelite top handle. This is for holding the cover when lifting it away from the
body or seating it properly on the body.
11. Body or side handles. This is used for holding the body of the cooker when
transferring it from one place to another.
The Smokehouse
A smokehouse is a device used in treating the fish or meat with smoke. It can be a
cold smoke house or a hot smokehouse. It is a hot smokehouse if the fish is in close
proximity to the source of smoke and a temperature of 66C to 88C is produced. If the
source of smoke is 2 meters away from the fish and the temperature of smoke is 32C –
43C, then it is a cold smokehouse. Some are simple like the barrel and drum types while
others are mechanized and controlled like the Torry smokehouse which can also be used as
a drier.
The Drier Smokehouse

The Parts of a Drier Smokehouse and their Functions
1. Removable slatted benches. They hold the fish to be smoked.
2. Removable hangers with hook. They are used for hanging fish to be dried or
smoked.
3. Wooden hooks. They are nailed from the top of a the drier smokehouse where fish
are also hanged when drying or smoking.
4. Vents. Theseare located below the roof at the front and back of the smokehouse to
provide the necessary air circulation.
5. Tunnel or pipe. Conveys the smoke from the concrete furnace into the smokehouse.
6. Concrete furnace. It is where the smoke – producing materials are placed and
burned.
7. Tight sheathing rafters. Serve as the top cover or roofing of a smokehouse.
8. Meshed screen. Serve as a closure to openings like the vents to keep flies and
insects from entering the smokehouse.
The Torry Smokehouse and Its Parts
Some Types of Smokehouse
1. Stainless Steel Smokehouse 2. Electric Smokehouse

3. Mechanical Smokehouse
Smokehouse control and sensor of an electric smokehouse
4. Barrel Type Cold Smokehouse 5. Brick Smokehouse

The Freezer and Refrigerator
The freezer and refrigerator are used in maintaining the freshness of raw materials
and in providing an ideal low or ambient temperature for storing processed foods.
Freezer for Fish A Two – Door Refrigerator
Compression System of Absorption System of
Refrigeration Refrigeration

The Parts of the Compression System of Refrigeration and their Functions
In a refrigerator, the heat evolved by the compression of a gas in the compressor is
removed by condensing coils. Still under pressure, the gas cools and condenses into a
liquid at the condenser which is released through a control valve into the evaporating
coils of the freezing compartment. As the pressure is removed, the liquid refrigerant turns
into a gas (vaporizes), causing a sharp lowering of temperature.
The Parts of the Absorption System of Refrigeration and their Functions
In this system, a small burner flame provides heat which drives out the gas from the
ammonia – water mixture. It utilizes an insulated box to keep the cold in and an evaporating
gas or refrigerant. A mixture of ammonia passes through the evaporatingcoils of the
freezing compartment where it evaporates into ammonia gas. The evaporation of ammonia
removes heat from the food. The ammonia gas then goes down to the absorber where it is
absorbed by water. A small amount of heat from the burner flame drives out the gas from
the ammonia – water mixture and condenses back into liquid ammonia as it passes through
the condensing coils.
Tools and Utensils Used in Food Processing and their Uses
1. Measuring Devices
a. Weighing scales
The triple beam balance is for measuring small quantities like spices,
preservatives, etc., while the heavy duty scale is for measuring fish, salt, etc.

Checkweigher scale is a digital weigher scale
used to get the weight of food like meat, fish,
vegetables, fruits, etc.
Clock Type weighing scale for food
b. Measuring spoons
A measuring spoon is a spoon used to measure an amount of a substance,
either liquid or dry, when cooking. Measuring spoons may be made of plastic,
metal, etc.
c. Measuring Cups
A measuring cup is a kitchen utensil used primarily to measure the volume of
liquid or powder-form cooking ingredients such as water, milk, juice, flour,

etc.Measuring cups can be in plastic, glass and stainless. From mini shot
measure to measuring pitcher and batter bowl.
Measuring cups for measuring liquid ingredients like milk, vinegar, fish sauce, etc.
Measuring cups for solid ingredients like flour, salt, minced garlic, etc
c. Thermometers
Thermometers indicate the degree of hotness or coldness of a thing or body.
It measures how high or how low the temperature is.

d. Glass Tube Thermometers
e. Salinometer
It is used to measure the salinity of a brine.

f. Psychrometer
It is used to measure the relative humidity of the air when sun drying.
Digital Sling Psychrometer
f. Anemometer
It is used to determine the velocity of the wind in sun drying.
g. Refractometer – used to measure the sugar concentration of sap and syrup
for food.

2. Cutting Implements
a. Knives
For cutting or slicing fish or meat; for scaling fish
b. Filleting knives
For filleting fish
c. Scissors
For trimming – off fins of fish

3. Descaler or scalers
They are used in removing the scales of a fish.
Electric Fish Scalers
Salting Equipment
Oil drum – used as a container to keep salted fish
during the process
Earthen pots are used in storing the salted products.

Wooden salting vat is a container used in the salting process.
Wooden shovel or spade is used for mixing or stirring
the mixture of salt and small fish for salting

5. Smoking Equipment
Baklad made of bamboo used in drying the fish prior to smoking
Bakol is a bamboo basket used to transport smoked
fish
Bistay is a bamboo basket for collecting sun
dried fish
Dinarayan is a smoking tray
made of wood

Panakip is a bamboo cover used to keep fish
submerged in the brine while boiling
Panandok is a big metal ladle to scoop up the
cooked fish from the boiling brine
Bamboo poles used to hold the baklad
With brine cooked fish while drying.
Pugon is a concrete heat source used when
pre-cooking fish in a brine

6. Others
For picking up or handling food
It is where fish or meat are cut; ingredients are
sliced or minced.

Refer to the Answer Key. What is your score?
Identify the following. Write your answer on the space provided for.
______________ 1. It is a device used to measure the strength of brine solution.
______________ 2. It is a device used to Measures the sugar content of sap and syrup.
_______________3. It means to set or determine the accuracy of the measuring device.
_______________4. It is the cheapest and most easily available sanitizer in the market.
_______________5. It is used in measuring the volume of liquid.
______________ 6. It is a device used to measure liquid ingredient in small quantity.
______________ 7. It is the type of water used in calibrating the refractometer.
______________ 8. It is a device used to measure the temperature of fish/food.
______________ 9. It is a device used to measure the weight of fish / food.
______________10.How many drops of sap or syrup sample are needed in testing the
refractometer?
______________ 11. It is use for cutting or slicing fish or meat; for scaling fish.
______________ 12. It is use for trimming of fins of fish.
______________ 13. It is use for picking up or handling food.
______________ 14. It is where fish or meat are cut; ingredients are sliced or minced
______________ 15. It is use in storing the salted products.
How Much Have You Learned?
Self-Check 1.1

 refractometer cover
 soft tissue paper or a cotton cloth
 salinometer
 blender
 outlet
 weighing scale and balance
 measuring cups of varying capacities
 measuring spoons
 thermometer
 cylinder
 beaker
 flasks
Materials
Use tools, equipment and utensils.
LEARNING OUTCOME 2
1. Printed procedures/ brochures/ catalogues are consulted and
reviewed according to specified food processing methods.
2. Standard procedures in using tools, equipment and instruments are
recalled and strictly followed according to manufacturer’s
specifications
3. Devices and instruments for measuring are properly checked,
sanitized and calibrated prior to use.
4. Tools, equipment and instruments are safely used according to job
requirements and manufacturers’ specifications.

Directions: Carefully read the questions below. Select the best answer from the options
given and write the letter only on your answer sheet.
1. Why is it important to review all procedures in using standard measuring devices?
a. To ensure proper use of standard measuring devices
b. To enable a food processor to use the appropriate measuring device
c. To enable a food processor to work systematically and accurately
d. All of these.
2. Your teacher instructed you to measure the salinity of brine you will use in curing fish.
Which of these will you do?
a. Recall and master the procedure in using a salinometer
b. Review and master the procedure in using the thermometer
c. Review the procedure in using a psychrometer
d. Review the procedure in using a refractometer
3. You were assigned to monitor the temperature of smoke inside the smokehouse. What
will you do to correctly perform your assigned task?
a. Recall and master the procedure in using a weighing scale
b. Review the procedure in using a refractometer
c. Review the procedure in using a thermometer
d. Master the procedure in using a salinometer
4. What would happen if you failed to follow the correct procedure in measuring liquid?
a. The obtained measurement is inaccurate
b. The work is not properly done
c. Both a and b
d. None of these
5. Which procedure will you master if you want to measure the sugar concentration of a
fresh sap or syrup?
a. How to use a thermometer
b. How to use a salinometer
c. How to use an anemometer
d. How to use a refractometer
Pretest LO 2
Let us determine how much you already know about the use fish processing
tools, equipment and utensils. Take this test.

Inspecting and Checking Condition of Equipment and Machines (USE)
Before any equipment or machine is used, it must first be checked to make sure that
it is very functional and in good condition. Checking and inspecting equipment and machines
will guarantee that all their parts are in tact and that no part is missing or defective. This will
also assure that electrical plugs and wirings are not defective and will not in anyway cause
problems on short circuits, electrocution or any form of accident. Religiously checking and
inspecting equipment and machines will facilitate Preventive Maintenance which include
checking the following:
1. Machine temperature
2. Hydraulic fluid
3. Wear and surface condition
4. Crack
5. Leak detection
6. Vibration
7. Corrosion
8. Electric insulation
Performing pre – operation activities ensures that all the tools, equipment and
utensils assembled, checked, inspected, sanitized, readied and stowed after use are the
appropriate devices required in processing the food based on the method of processing that
will be undertaken like salting, curing, smoking, fermentation, pickling, canning, bottling,
processing using sugar, drying, and dehydration or artificial drying. Doing this will prevent
the use of inappropriate devices as well as well as the occurrence of accidents due to the
use of faulty or defective tools, equipment and utensils.
Sanitizing and disinfecting the tools, equipment and utensils will destroy all germs
and microorganisms which were not removed after washing with soap and water. Proper
cleaning and disinfecting leads to:
1. Minimizing product rejection, return and complaints due to defects resulting from
the use of defective or inappropriate tools, equipment and utensils
2. Lengthening product shelf life due to the reduction of contamination resulting
from the use of properly sanitized and disinfected tools, utensils and equipment
3. Reduction of the risk on food poisoning due to the use of unsanitized tools,
equipment and utensils.
Read the Information Sheet 2.1 ,2.2 and 2.3 very well then find out how much
you can remember and how much you learned by doing Self-check 2.1, 2.2 and
2.3.

4. Facilitating preventive maintenance which include checking the machine
temperature, hydraulic fluid, wear and surface condition, crack, leak detection,
vibration, corrosion, and electric insulation.
B. Cleaning and Sanitizing Equipment and Instruments
The use of sanitizing agents leads to effective sanitation of tools, equipment and
utensils. Sanitation with the use of physical and chemical sanitizing agents will kill residual
microorganisms that remain after cleaning. Cleaning by washing with soap and water is very
important as it ensures the removal of dirt or debris by physical and/or mechanical means.
Clean water is to be used to finally wash and rinse all utensils, tools and equipment.
Sanitizing or disinfecting, on the other hand, rids or reduces the number of micro-organisms
on surfaces where food comes in contact with. It cannot be accomplished until surfaces
where foods are processed are clean. Moreover, it cannot be effective without a good pest
control program.
Cleaning alone by washing will not be capable of totally eradicating microbes, germs
and viruses, hence the need to use sanitizing agents. Some sanitizing agents are detergent
solution for scrubbing surfaces of processing tables, 150 – 200 ppm chlorinated water for
sanitizing. All tools and utensils are also cleaned and sanitized with the use of detergent
solution rinsed with tap water before sanitizing with 150 – 200 ppm chlorinated water by
soaking.
Chlorine is one of the cheapest and most easily available sanitizers in the market. It
is popularly used in the treatment of water for both household and plant. Likewise, chlorine is
also used to sanitize processing equipment.
Area / Materials to be Sanitized
Volume of
Water
Volume of
Chlorine
Time (Minutes)
Hand Dip 5 gallons 10.8 ml 2-5 minutes
Equipment 5 gallons 54 ml 2-5 minutes
Floor 5 gallons 125 ml 20 minutes
For food processing: Washing of
vegetables and poultry
5 gallons 27 ml 2-5 minutes
1. Procedure in Cleaning Equipment and Instruments
a. Wash all the equipment / instruments with soap.
b. Rinse with clean water.
c. Sanitize by dipping into approved sanitizer solution.
d. Remove from the solution.
e. Allow to air dry.
2. Procedure in Sanitizing:
a. Prepare all the materials needed.
b. Measure a certain amount of chlorine and water.
c. Mix and dip the equipment / instruments in the mixture.

d. Remove from the sanitizing solution.
e. Dry thoroughly.
Calibrating Measuring Devices and Instruments
1. Procedure in Calibrating
a. Weighing Scale
Check the accuracy, see to it that the hand is pointed at zero in an
empty weighing scale.
b. Salinometer
Check the accuracy by measuring 20o
salinometer brine solution.
Checkif the salinometer records the reading correctly.
c. Refractometer
Place a drop of water (preferably distilled) in the dark circular
orrectangular area and close the cover. A shadow or dark area is
visible on the scale inside the eyepiece. Turn the calibration screw
until the shadow falls on the zero mark. Open the refractometer
cover and dry the cover and glass prism using soft tissue paper or a
cotton cloth.
d. Thermometer
Check the accuracy by dipping it in hot food to see if the mercury
rises to desired temperature.
Proper Stowing of Tools, Equipment and Utensils
Tools, equipment and utensils must be properly stowed in order to protect them from rusting,
contamination, etc. and thus lengthen their serviceability. They must be kept in clean
cabinets which are well – ventilated and not subjected to drafts or rain.
Tools and utensils which were washed must be drained and wiped – dry before
keeping them. They are kept in an orderly way in order that it will be easy to assemble or
prepare them when needed. The cabinets or racks where they are kept must be properly
labeled for easier identification on the part of the user.
Procedure:
1. Wash the equipment/instruments with soap.
2. Rinse thoroughly with clean water.
3. Sanitize by dipping or soaking in a sanitizing solution.
4. Rinse with clean water.
5. Drain.
6. Dry thoroughly (Air Dry).
7. Wipe with a clean piece of cloth.
8. Check the accuracy of the equipment/instruments.
9. Pack/store/keep in a clean dry cabinet.
Procedure in Cleaning, Sanitizing, Calibrating and Stowing Equipment and
Instruments
1. Wash the equipment / instruments with soap.

3. Sanitize by dipping or soaking in sanitizing solution.
4. Remove from the sanitizer solution.
6. Dry thoroughly (air dry).
7. Check the accuracy of each equipment and instruments.
8. Pack and keep in a clean cabinet.
Directions: Carefully read the questions and choose the best answer from the options given.
Write the letter only of your answer in your test booklet.
1. What are some of the specifications included by the manufacturer of a certain
tool, equipment or utensil?
a. dimension as to size, height, capacity, etc.
b. handling and operating requirements
c. proper care and maintenance
d. all of these
2. Why are specifications for food processing tool, equipment and utensils
necessary?
a. because they provide information to the user as to how they must be
properly handled and operated in order to avoid accident
b. specifications give information concerning the proper use, care and
maintenance of the tools, equipment and utensils
c. both a and b
d. specifications provide information about the tools, equipment and utensils
3. If you are a food processor, why do you need to know the parts of the equipment,
tool and utensil and their functions?
a. to appreciate the usefulness of a particular device
b. to be able to correctly operate/manipulate a tool, equipment or utensil
c. to be able to do some simple repairs on them
d. to easily determine if a part is missing
4. If you are going to pack processed foods in tin cans, why do you need to seal it
with a can sealer?
a. cans cannot be sealed manually
b. tin cans are difficult to seal
c. to properly seal them
d. a can sealer is the appropriate equipment for attaching the cover to the
body of a tin can with is first and second operation rolls
5. What will help you determine the kinds of tools, equipment and utensil you will
assemble, sanitize, inspect or check?
a. the kind of product to be produced
b. the method of food processing to be done
c. the raw materials to be processed
d. the availability of tools, equipment and utensils
Self-Check 2.1

6. You have already removed the dirt from the tools, equipment or utensils you will
use in processing the food by washing them with soap and water. Why do you
still need to sanitize or disinfect them?
a. washing with soap and water only removes the adhering dirt
b. washing alone cannot remove the microorganisms and germs
c. to effectively kill or destroy all the germs and microorganisms which
remained after washing
d. all of these
7. Which of these is a sanitizing agent you can use for killing the germs and
microorganisms present in tools, equipment and utensils?
a. sodium chloride
b. sodium hypochloride
c. magnesium sulfate
d. calcium chloride
8. How will you properly store tools, equipment and utensils after using them?
a. wipe dry all tools, equipment and utensils which were washed with water
before keeping them
b. stow them in a clean dry place with a good ventilation
c. apply lubricant to parts of equipment that undergo friction to prevent wear
and tear
d. all of these
9. Why do you need to inspect and check the condition of equipment and machines
before operating them?
a. to check if no parts are defective or missing
b. to check if electrical plugs are in good condition
c. both and b
d. to see if they are old or new ones
10. Which of this preventive machine maintenance will you check before using
equipment or a machine?
a. machine temperature and hydraulic fluid
b. wear and surface condition
c. crack and leak detection and electric insulation
d. all of these

Procedures in Using Standard Measuring Devices and Instruments
1. Salinometer
a. Prepare brine solution.
b. Pour brine solution in a cylinder.
c. Dip salinometer in brine solution.
d. Record the reading.
e. Clean instrument after using.
2. Thermometer
a. Dip thermometer in boiling liquid.
b. Record the reading by O
C or O
F
c. Clean after using.
3. Refractometer
a. Place a drop of fresh sap or syrup sample on the refractometer.
b. Close the cover.
c. Quickly read the scale (the line on the top of the darker area). Readings
should be taken to the nearest 0.1 percent.
d. Rinse with water after each reading and dry with tissue paper.
4. Glassware like cylinder, beaker, flask
a. Pour liquid ingredients into the cylinder, beaker, or flask.
b. Bring the cylinder to eye level.
c. Get the reading at the lower meniscus.
d. Record the reading.
e. Clean after using.
5. Weighing scales
Put the food on the weighing scale. Record the reading in grams or kilograms.
6. Measuring cups for dry ingredients
Gently spoon the ingredients into the cup, filling the cup to overflowing. Then
level off with a metal spatula or straight-edged knife.
7. Measuring cups for liquid ingredients
Pour liquid on level surface of measuring cups. Have the measuring lines at
eye level to be sure of the exact measurement.
It is important to review all procedures regarding the use of all standard measuring devices
to ensure that they will be properly used in accordance with manufacturer’s specification.
Being familiar with the procedure in using a standard measuring device like a salinometer,
thermometer, weighing scale or a measuring cup or spoon will enable a food processor to

use the appropriate measuring device for a specific food processing activity. It also enables
him to work systematically and accurately.
Complete the statements by writing your answer on the space provided.
1. _________________ is the behavior that agrees with the accepted or
conventional standards.
2. _________________ is formed by design or invented for specific use.
3. _________________ means to divide into or mark with degrees.
4. _________________ refers to a place where any work is carried out.
5. _________________ is a solution of salt and water.
6. _________________ means a systematic arrangement of listed items giving
descriptive details.
7. _________________ are things that provide specific service or function
8. _________________ is a tool or utensil.
9. _________________ is a pamphlet.
10. _________________ is used as a basis of comparison or established criterion.
Self-Check 2.2

Equipment are the tools, supplies and other items needed for a particular task.
When processing food, there are several equipment that are to be used. These include the
following:
1. cooking equipment like ovens and steam – jacketed kettles
2. refrigeration and low temperature – storage equipment like refrigerators and
freezers
3. cutting implements like slicers, mixers, grinders and choppers, etc.
A food processor, however, must know the essential informationregarding the
equipment in terms of how they must be operated or used in accordance with the
manufacturer’s specifications.
Before operating any equipment, it is important to be familiar with the manufacturer’s
specifications, which include:
1. Handling requirements
2. Operating requirements
3. Discharge label
4. Reporting
5. Testing
6. Positioning
7. Refilling
Interpreting Manufacturer’s Specifications
Food processing equipment when sold are provided with a manual containing the
manufacturer’s specifications and a necessary reminder to the processor in the form of a
sticker or Warning Label is attached to the equipment itself as an assurance that the
equipment/machine or tool is in excellent condition for it has passed quality control in its
construction.
The specification usually gives a detailed description about the equipment,
dimensions, materials, and other relevant information regarding the equipment or machine.
The dimension gives the measurement of the size of an object in terms of length,
width, or height of the equipment/machine or tool.
The capacity specifies the measurement of the amount, which a device can hold or
contain as in boilers, cooker, or steamers or a weighing scale.
The manufacturer’s specifications are usually contained in the manual, which
accompanies the equipment. The food processor must thoroughly read and understand all
the information contained in the manual especially if the equipment is to be operated
electrically. Aside from knowing the correct operation of the equipment or machine, it is also
important to know this information:

1. Basic safety precautions to follow when using the equipment
2. Warning labels which specify how to properly operate an equipment
3. Instructions on the proper care of the equipment/machine
4. Instructions on the correct operation of the equipment
The manufacturer’s specifications must be thoroughly readand understood by the
food processor and sees to it that he interpreted them in such a way that a food processing
equipment can be properly operated.
Below are some examples of manufacturer’s specifications, which must be properly
interpreted resulting to an accurate and safe operation/manipulation of an
equipment/machine:
Directions for Use of the Hydrometer
1. Clean the hydrometer thoroughly and dry it before using it each time. Handle
with clean dry hands or with clean cloth.
2. Use with fluid juices, otherwise if the liquid to be tested is thick or slimy, the
resting point of the hydrometer will be uncertain.
3. Pour a small quantity of the juice into a glass cylinder and drop the hydrometer
carefully.
4. Make sure that the instrument is floating freely and touches neither the bottom
nor the sides of the cylinder.
5. To read correctly, set eye level with the surface of the liquid.
6. Since the specific gravity of juices varies with temperature, bring the juice to the
standard temperature for which the hydrometer is adjusted usually 16C or 60F
or make the necessary corrections in the reading. Add 0.1% for every 3 above
the standard and subtract 0.1% for every 3.
Tips on the Proper Use and Care of a Refrigerator
1. Put only clean food in the refrigerator.
2. Put only clean containers in the refrigerator. Wipe before refrigerating them.
3. Keep the refrigerator closed.
4. Keep fatty substances and hands off the rubber seal or gasket of the refrigerator
door. A gasket kept in good condition seals the cold air in the refrigerator.
5. Wash and clean the refrigerator once a week with warm water to which a little
baking soda has been added. This is prepared by mixing one teaspoon of baking
soda per quart of water. The exterior should be washed with soap and water and
then rinsed and dried. Avoid the use of abrasives.
6. Remove ice cubes by letting cold water run over them in the ice – cube pan.
Removing them with an ice pick is liable to puncture the pan.
7. Defrost the refrigerator as follows:
a. Turn – off the freezing unit
b. Refill the ice cube pan with warm water not hot water, and place it on the
bottom of the shelf of the freezing unit
c. Keep the drip tray in place to catch the melting ice that drops off
d. Wash and refill the ice cube
e. Wash the refrigerator and the drip pan. Never try to speed up defrosting
by prying – off ice.
f. When done, turn the freezing unit on.

General Directions for Using Pressure Canners for Fruits and Vegetables
1. Assemble materials and equipment. Pressure should be thoroughly cleaned with
soap and water.
2. Check jar rings and closures. Wash and rinse thoroughly.
3. Have plenty of boiling water available.
4. Sort food for size and degree of ripeness.
5. Pour hot water into washed jars until needed.
6. Follow specific directions for best results.
7. Preheat or precook food as per recipe.
8. Place 2 quartz of boiling water in cooker with basket in place. Set cooker on
heat.
9. Place clean, sterile rubber rings on jar or cover as directed, when closure
requires separate rings. Return jars to hot water until ready to fill.
10. Fill hot containers promptly with hot food according to given directions.
11. Fill jar to proper level with boiling liquid when recipe so requires. Don’t fill the
container up to the top but allow space for any expansion. All equipment used
should be clean.
12. Work out bubbles with a clean knife or spatula. Wipe sealing edge with clean wet
cloth.
13. Adjust closures on jars according to directions for types of closures used. If
bottles are used, close tightly and then turn back by ¼ inch.
14. Place each hot container inside the pressure canner. Do not have these
containers in direct contact with pressure – canner bottom or sides.
15. Put cover on cooker and lock in closed position. Use maximum heat under it.
16. Watch for steam to come from the petcock. Petcock valve should be opened
wide. Under no conditions should pressure be raised in the cooker until it is in
exact position.
17. Allow steam to come out freely for 7 – 10 minutes to eliminate all air pockets.
Close petcock.
18. Use maximum heat to raise pressure to required point and then lower heat to
maintain the pressure desired. Start counting processing time the moment
required pressure is reached. To eliminate fluctuations in pressure, pressure
cooker should be kept at required point by raising or lowering the heat as
needed.
19. Turn off heat at end of processing time or move cooker from heat at end of
processing time when using electric stove or any other constant heat unit.
20. When canning in glass jars, allow pressure to return to zero of its own accord.
When indicator reaches zero, let cooker cool for 2 – 3 minutes.
21. Open petcock. Remove cover from cooker. Under no circumstances should its
cover be turned until dial on the steam gauge points to zero. Lift cover so steam
is away from you.
22. Immediately toss dishtowel over cooker and containers. Let cooker stand for 3 –
4 minutes.
23. Remove basket of jars from cooker and place on board or towel free from draft.
Be sure to follow the directions that come with pressure canner. Bear the
alterations in mind. With regard to altitude processing, increase the pressure by 1
pound for every 508 meters or 2, 000 feet above sea level.

How to Seal Tin Cans with Hand Automatic Can Sealer
1. Fasten sealer firmly to table or armchair using clamp.
2. Attach crank to worm shaft and tighten set screw.
3. Change the chuck, height washers, and levers to the size of can to be sealed.
4. Lower base plate by turning can lifter handle as far as possible to the left.
5. Place cover on can and set can on base plate.
6. Place the first operation roll and rivet in the first adjusting lever.
7. Raise can until it is clamped firmly between base plate and chuck.
8. Turn crank clockwise (eleven turns) until the first operation roll is through half
sealing. After half – sealing, the cans are placed in the pressure cooker for 15
minutes exhausting to form vacuum.
9. After exhausting the cans, remove first operation roll and put the second
operation roll and rivet in the adjusting lever.
10. Turn crank clockwise (ten turns) until the second operation roll returns to its
normal position away from the chuck.
11. Release sealed cans by turning can lifter handle as far as possible to the left.
The machine is now ready to receive another can for sealing.
Instructions for Changing the Automatic Can Sealer from One Size to Another
1. Pull down on chuck, which will slip out of place. While sealer is new it is
sometimes necessary to force the chuck by placing a screwdriver against the
chuck shaft, which is inside the chuck holder bushing.
2. Remove base plate, base plate shaft, and height washers. Put washers, marked
with the size of can to be sealed on top of the compression spring.
3. Lift the rivet from the adjusting lever. Move the adjusting lever until the rivet is
inserted into the hole marked with the size of can to be sealed. The rivet should
be changed on both first and second operation side of sealer.

How to Use the Pressure Cooker
1. Place one – and – a – half (1/2) inch water in the cooker
2. Put rack with stand in the bottom of the cooker. A rack can be old bottles or milk
cans of the same height filled with water.
3. Place the packed glass jars on the rack in the cooker.
4. Put on the cover of the cooker. Be sure the cover arrow aligns with “line mark” on
rim of the body of the cooker.
5. Tighten two opposite bakelite wing nuts or knobs at the same time evenly. Never
tighten one wing nut or knobs at the same time evenly. Never tighten one wing
nut or knob at a time.
6. Turn on the stove. The water in the cooker begins to boil at 212 F or 100C at
sea level forming steam. The steam drives out the air through the vent pipe and
heat begins to penetrate the glass jars.
7. Exhaust the air in the cooker for 8 to 10 minutes so that air cannot interfere with
the passage of heat.
8. Close the vent pipe by putting the pressure regulator weight. The hole of the
pressure regulator weight should correspond to the desired pressure directly over
the vent pipe. For instance, if the desired pressure is 10 pounds so the pressure
regulator weight hole of 10 be inserted over the vent pipe.
9. When vent pipe is closed, the steam can no longer escaped so the pressure rises
up to the desired pressure. The pressure regulator weight jiggles or rocks when
the pressure is reached. This is called coming up time (CUT). Water under
pressure boils at temperatures above 212F. At 10 pounds pressure gauge
pressure, water boils at 240 F. Then regulate the fire.
10. If desired pressure is reached, start counting the processing time. If processing
time is 90 minutes, so maintain the pressure and temperature for 90 minutes. At
this stage, heat penetrates the jar by conduction or heat passes from one
vibrating molecule to another. It also penetrates by convection in which heated
fluids expand, rise, and are replaced by cooker fluids. In other words, heat
penetrates the jar by both conduction and convection. Likewise, headspace of
one half (1/2) inch of the jar acts as a cushion. In jars, the pressure usually gets
so great that most of the air is driven out under the cover. The pressure and
temperature in the jar is finally the same with the pressure cooker.
11. At the end of the processing time, turn off the stove. Temperature and pressure
begin to fall as the cooling off period starts. Wait until the gauge registers to zero
(0) pressure and remove the pressure regulator weight.
12. Loosen two opposite bakelite wing nuts or knobs at the same time. When all
wing nuts were loosened, open the cover of the cooker in slanting position away
from the face.
13. Get immediately the glass jars one at a time from the cooker and close. Invert
the glass jars to determine if bubbles continuous to flow as sign of good sealing.
14. Cool the glass jars in room temperature as well as the cooker.

How to Care for the Pressure Cooker
1. Wash the pressure cooker if it is already cooled.
2. Store the cooker in a dry place. The cover is stored separately from the cooker
body.
3. Be sure the cooker and cover are thoroughly dried to protect against pitting and
corrosion.
4. Protect the metal – to – metal seal from being struck or dented.
5. Protect the metal - to – metal seal must be lubricated periodically with Vaseline
oil to prevent the cover from scratching and sticking to the bottom. The metal – to
– metal seal must not be permitted to become dry, as this could result on severe
damage to the metal – to – metal seal and make it very difficult to remove the
cover.
6. Wipe periodically the metal – to – metal seal with clean towel to remove any build
– up of foreign material trapped in the lubricant.
7. Avoid hard scrubbing of the metal – to – metal seal to prevent damage.
8. The steam pressure gauge should be checked most often for its accuracy.
9. To prevent from pitting the cooker, wash, rinse and dry the cooker thoroughly
every use. Do not wash the cooker while it is still hot.
10. Place lubricant on the threads of the bakelite wing nuts or knobs to help the
knobs turn more easily and hold the cover securely to the cooker, preventing
steam leaks.
11. Before using the cooker, hold the cover and bring against the light to see if vent
pipe is clear. If you cannot see the light through the vent pipe, insert carefully a
piece of wire in the vent pipe and run it gently in and out to be sure the tube is
clear. Rinse the vent pipe with hot water.
12. Be sure there is always water in the cooker during canning. If cooker boils dry
on the process of canning, never add cold water only hotwater must be added.
Do not subject cooker to sudden change of temperature, as this will cause
expansion or contraction, which can crack a cast aluminum utensil.
13. Pressure cooker should never be made more than 2/3 full when cooking foods
like arrozcaldo with milkfish bone meal FPC. When coking foods which expand,
fill cooker one – half full.

Procedure for Calibrating Equipment
Below is a sample of a manufacturer’s specification on calibrating a measuring
device in order that the measurement that will be obtained is accurate:
Calibrating a LoadtracConsolidometer
1. Assemble the consolidometer with a hard steel disk of approximately the same
height as the test specimen and 1millimeter smaller diameter than the ring.
2. Moisten the porous stones and filter papers.
3. Sufficient time, a minimum of 2 minutes, shall be allowed for the moisture to be
squeezed from them during each increment of the calibration process.
4. Load and unload the consolidometer as in the test and measure the deformation
for each load applied.
5. Plot corrections to be applied to the deformation of the test specimen.
Equipment/Machine Wear and Tear
One factor to consider in the selection/purchase of food processing equipment is the
construction materials used in making the equipment/machine, tool or utensil. Food
equipment and utensils have food contact and non – food contact surfaces. Food
contact surfaces are the parts which normally come into contact with food or from which
normally come into contact with food may drain, drip, splash, or spill into or onto a surface
that is normally in contact with the food. Non – food contact surfaces are the remaining parts
and the surrounding area that should not make contact with the food during the production.
The food contact surfaces are usually the parts that undergo wear and tear due to rubbing
surfaces, which undergo friction.
The Food and Drugs Administration (FDA) and construction standards from Nation
Sanitation Foundation (NSF) International and Underwriters Laboratories Inc. require food
equipment and utensils to be:
1. Smooth
2. Seamless
3. Easily cleanable
4. Easy to take apart, disassemble or dismantle
5. Easy to put together or reassemble
6. Equipped with rounded corners and edges
Materials used in the construction of utensils and food – contact surfaces of
equipment must be non – toxic and not impart color, odors, or tastes to foods. Stainless
steel is a preferred material for food contact surfaces.
Under normal use, the materials should be safe, durable, corrosion – resistant, and resistant
to chipping, pitting, deterioration and wear and tear of parts.
It must be noted that through constant use, equipment or machine parts suffer from
wear and tear as a result of friction brought about by the rubbing surfaces or those that
undergo corrosion due to a chemical reaction with substances present in the food.

To be able to address problems on wear and tear of equipment/machine parts, they
must be regularly inspected and checked to determine their condition. The right selection of
equipment based on the construction materials will largely help in minimizing wear and tear
that affects machine efficiency.
Below are the kinds of construction materials for equipment:
1. Metals
Chromium over steel gives an easily cleanable, high - luster finish. It is used
in toasters, waffle irons, etc. Noncorrosive metals formed by the alloys of iron, nickel,
and chromium are also used in the construction of food service equipment.
Lead, brass, copper, cadmium, and galvanized metal must not be used as
food – contact surfaces for equipment, utensils, and containers because they cause
chemical poisoning if they come in contact with the food.
2. Stainless steel
Stainless steel is the most popular materials for food operations.
It is commonly used as food containers. It has a highly durable finish with a shiny
surface which is easy to clean and maintain.
3. Plastic
Plastics and fiberglass are frequently used in foodservice
equipment because they are durable, inexpensive, and can be molded into different
combinations.
Some examples of plastics used in food establishments are:
1. Acrylics - used to make covers for food containers
2. Melamines – used for a variety of dishes and glassware
3. Fiberglass – used in boxes, bus trays, and trays
4. Nylons – used in equipment with moving parts
5. Polyethylene – used in storage containers and bowls
6. Polypropylene – used for dishwashing racks
4. Wood
Wood is light in weight and economical but it is porous to bacteria and
moisture and it absorbs food odors and stains. Wood also wears easily
under normal use, which requires frequent maintenance and repair. Wood is
used for cutting boards, cutting blocks, etc.
Two of the FDA and construction standards from NSF International and Underwriters
Laboratories Inc. for food processing equipment are easy to dismantle or disassemble and
easy to assemble.

To ensure that food processing equipment can be properly maintained in line with
company or organization’s maintenance system. The condition of machine parts can be
easily detected as to the presence of:
a. wear and tear
b. cracks
c. leaks
d. corrosion
If the parts of equipment are easy to assemble and disassemble then the condition of
machines or equipment can be easily reported as:
a. serviceable
b. repairable
c. defective
d. replaceable
If the parts are easy to assemble and disassemble, it is easy to dismantle machine
parts that breakdown so they can be repaired or replaced right away.

Multiple Choice
Directions: Read and understand the questions below. Select the best answer and write
the letter only on your answer in your test booklet.
1. Why is there a need of properly interpreting teacher’s/manufacturer’s
specifications before operating any food processing equipment?
a. to be able to determine the correct operation of the equipment
b. to avoid accidents due to faulty operation of equipment
c. to be familiar with their parts and their function
d. all of these
2. If you will choose food processing equipment, why is it better those with parts
easy to assemble and disassemble?
a. for easily taking the parts apart if it breakdown
b. to easily put back the parts after dismantling them
c. both a and b
d. because they are cheaper
3. Why should you check equipment that are electrically operated before using
them?
a. to make sure plugs, outlets and electrical insulation are not defective
b. to prevent accident
c. to practice using the equipment
d. to avoid errors and accidents in their operation
4. Your teacher instructed you to use a blender in your activity of preparing mango
jam. It is your first time to use such equipment. Which of these will you do?
a. read the manual containing the manufacturer’s specification
b. practice using the blender
c. ask your classmate to demonstrate it to you
d. I will not do anything
5. Your can sealer is not sealing properly. Which of these will you do?
a. do not use it any more
b. request that a new sealer will be bought
c. undertake simple troubleshooting
d. borrow a can sealer from another class
6. Why should food contact surfaces of machine or equipment be regularly
lubricated?
a. to prevent wear and tear
b. to prevent corrosion
c. both and b
d. none of these
Self-Check 2.3

7. You noticed that it is difficult to turn the knobs of a pressure cooker, which of
these will you do?
a. change the knobs
b. apply lubricants like grease or oil at the screws
c. remove the knobs
d. don’t do anything
8. Your teacher instructed you to check and inspect all the food processing
equipment in your laboratory room. Which of these will you do later?
a. prepare a written report following the standard format
b. make a checklist of the tools and equipment inspected
c. make an oral report
d. none of these
9. Why should you operate or use equipment in accordance with manufacturers
specifications?
a. to correctly operate them
b. to be familiar with their parts and functions and to correctly operate, care
and troubleshoot them
c. to determine cost of equipment
d. to be familiar with the necessary safety precautions to observe
10. Which construction material for equipment porous to bacteria and absorbs
moisture as well as impart odor and color to the food?
a. plastic
b. metal
c. stainless steel
d. wood
Calibrating Refractometer
Material Tools and Equipment:
 refractometer cover
 soft tissue paper or a cotton cloth
Show that you learned something by doing this activity
HowDo YouApplyWhatYou HaveLearned?
Operation Sheet 2.1

Instructions: Follow the step by step procedures on how to calibrate a refractometer
Procedure in Calibrating Refractometer
Step 1.
Step 2.
Step 3.
Step 4.
Place a drop of water (preferably distilled) in the dark
circular or rectangular area and close the cover.
A shadow or dark area is visible on the scale inside the
eyepiece.
Notice that the reading is taken where the blue and the
white meet. Calibrate to ZERO using distilled water as
the sample.
Turn the calibration screw until the shadow falls on the
zero mark
This is what the winemaker sees once he has properly
calibrated the refractometer.
Open the refractometer cover and dry the cover and
glass prism using soft tissue paper or a piece of
cotton cloth.

Using Salinometer
Procedure:
1. Prepare brine solution. 4. Record the reading
2. Pour brine solution in a cylinder. 5. Clean after using.
3. Dip salinometer in a brine solution.
Operation Sheet 2.2

Proper Use of Blender
Equipment, tools and materials:
 blender
 outlet
Procedures:
1. Check and inspect the blender and outlets.
2. Insert the plug of blender into the outlet.
3. Switch – on the blender.
4. Operate blender in accordance with manufacturer’s specifications.
5. Clean and sanitize in accordance with specifications.
Precautions:
1. Wear appropriate protective outfit when working.
2. Proper care in handling the equipment.
3. Check accuracy of the equipment.
Stowing Equipment and Instruments
Equipment, Tools and Materials Needed:
 Weighing scale and balance
 Measuring cups of varying capacities
 Measuring spoons
 Salinometer
 Thermometer
 Cylinder
 Beaker
 Flasks
Procedures in Cleaning, Sanitizing, Calibrating, and Stowing Equipment and
Instruments:
1. Wash the equipment / instruments with soap.
3. Sanitize by dipping or soaking in sanitizing solution.
4. Remove from the sanitizing solution.
6. Dry thoroughly (air dry).
7. Check the accuracy of each equipment and instrument.
8. Pack and keep in a clean cabinet.
Precautions:
1. Wear appropriate clothing when working.
2. Proper care in handling the tools, devices and instruments.
Operation Sheet 2.3
Activity Sheet 1.1

3. Check the accuracy of the equipment/instruments.
Performance Criteria Checklist for
Operation Sheet 2.1
Calibrating Refractometer
Did the student/s… YES NO N/A
1. review the procedure in calibrating measuring
instruments?
2. check, sanitize, and calibrate the refractometer?
Student’s Name__________________________ Date ________________
Comments/Suggestions:
Find out by accomplishing the Performance Criteria Checklist honestly and
sincerely. Remember it is your learning at stake!
How Well Did You Perform?

Operation Sheet 22..22
UUssiinngg SSaalliinnoommeetteerr
1. review procedure in using the salinometer?
2. follow the procedure in using salinometer?
3. record the readings accurately?
Operation Sheet 2.3
Proper use of Blender
Did the student… YES NO N/A
1.prepared the equipment and checked before using?
2. demonstrated the proper plugging into the outlet
before switching?
3. cleaned and sanitized the equipment before and
after using in accordance with specifications of
teacher’s instructions?

Activity Sheet 1..11
Stowing Equipment and Instruments
1. identify and classify standard measuring devices and
instruments?
2. apply the proper ratio in preparing the sanitizing
solution?
3. check the accuracy of the equipment/instruments?
4. pack/store/arrange the stowed instruments in a clean dry
cabinet?

 can sealer
 pressure cooker
 gas stove
 table
Materials
Perform post-operation activities
LEARNING OUTCOME 3
1. Switching off/unplugging procedures of food (fish) processing
equipment is described in accordance with manufacturer’s specifications.
2. Food processing tools are cleaned, sanitized and stored as required
according to manufacturer’s specifications and workplace policies and
regulations.
3. Procedures in cleaning, sanitizing and storing food processing
equipment and instruments are described according to manufacturer’s
specifications and workplace policies and regulations.
4. Minor preventive maintenance procedures on equipment and
instruments are discussed in line with organization’s maintenance
system.
5. Defective tools, equipment and instruments are disposed according to
environmental procedures.

Multiple Choice:
Directions: Read and understand the questions below. Select the best answer from the options
given. Write the letter only of your answer in your test booklet.
1. Why do you need to inspect and check equipment/machines before, during and after
using them?
a. to make sure they are in good condition
b. to determine defective machine parts
c. to determine trouble shooting activities to perform
d. all of these
2. There is a strong odor of a gas coming from the LPG tank of the gas range in your
Food Processing Laboratory Room, which of these will you conclude?
a. the LPG tank has a leak
b. The hose connected to the LPG might be leaking
c. The LPG regulator is defective
d. All of these
3. In order to prevent electrocution or fire due to short circuits, which of these should
you do before using any equipment/machine?
a. check electrical outlets
b. check plugs and switch of electrical equipment/machines
c. check electrical cords
d. all of these
4. Which of these is a manufacturer’s specification concerning the use of a freezer in
the food processing plant?
a. Switch off before unplugging
b. Just unplug even if not switched off
c. Do not defrost regularly
d. None of these
5. To prevent the metal surface of your gas range, oven and gas stove to corrode,
which of these should you do?
a. wash with soap and water
b. wipe off spilled food then wash and wipe thoroughly
c. scrape the surfaces with spilled food then apply lubricants
d. none of these
Pretest LO 3
Let us determine how much you already know about the use farm tools and
equipment. Take this test.

Perform Post-Operating Procedure
Equipment are essential machines in a food processing plant that are important in
undertaking activities in line with processing foods like fish, meat, fruits and vegetables
through salting, smoking, drying, pickling, freezing or canning. In every method of
processing or preserving the food, different kinds of equipment are used. To ensure that
there is a smooth operation of any equipment, they must be properly maintained. Proper
maintenance starts with regular checking and inspection of their parts, proper use or
operation/manipulation, and conducting post operation activities such as cleaning/sanitizing,
applying oil and lubricants to machine parts before stowing or storing them until such time
that they will again be used. Equipment/machines which undergo regular preventive
maintenance have a longer serviceability and are more efficient in terms of their operation.
Inspecting and Checking Condition of Equipment/Machines Before, During and After
Operation
All equipment/machines to be used in processing /preserving foods like fish, meat,
fruits and vegetables must be inspected and checked to determine their condition prior to
use and even after using them. Before they are to be stowed or kept after use, they must be
inspected and checked to make sure they are in good condition and ready for use in the next
processing operation. Religiously inspecting and checking the equipment/machines after
use will help determine the presence of damaged or defective parts that need to be repaired
or replaced. Inspecting and checking the equipment /machines will also help determine the
presence of equipment/machines that breakdown and cannot be used in the next processing
operation. Defective plugs, switch and other parts of equipment/machines that are
electrically operated will also be determined and thus avoid accidents like electrocution and
other hazards arising from short circuit, etc.
Inspecting and checking the equipment before, during and after using them will also
help in effectively planning and efficiently carrying – out trouble shooting and preventive
maintenance activities which include checking the following:
1. Machine temperature – this is checked to avoid overheating
2. Hydraulic fluid – this must be checked to guarantee that the equipment/machine
which is operated by water or other liquids moving through pipes under pressure
will function well

3. Wear and surface condition – this is being checked to make sure no machine
parts are deteriorating or defective due to everyday use
4. Crack – this needs to be checked to see to it that there are no broken parts in an
equipment or machine which will cause the breakdown of the machine or as a
source of leak
5. Leak detection – this is checked to prevent accidental release of gas, water, oil,
etc. from the machine
6. Vibration -
7. Corrosion – this is checked to minimize wear and tear of parts by washing, drying
and lubricating machine parts.
8. Electric insulation – this must be checked to guarantee that there are no livewires
exposed during the operation of an equipment which may result to short circuits
or electrocution and even fire.
Proper Maintenance Of Some Food Processing Equipment
Below are some equipment used in processing foods that need to be regularly
inspected and checked before, during and after operation:
1. The Can Sealer

2. The Pressure Cooker
3. The Mechanical and Electric Smokehouses
4. The Freezer and Refrigerator

5. The Electric Fish Scalers
6. The Oven and Gas Stove
Gas stove

7. The Food Processor/Blender and Juice Extractor
8. The Vacuum Packer 9. The Electric Polysealer
Performing Minor Troubleshooting
Troubleshooting on equipment/machines that breakdown is very essential in a food
processing plant. This is a way by which faulty/malfunctioning or defective machine parts
are diagnosed and their appropriate repair or replacement is effectively done. Performing
minor troubleshooting of equipment/machines that breakdown ensures a longer capability of
the equipment/machine to be operated or used. Minor troubleshooting must be done in
accordance with manufacturer’s specification by a repairman who is an expert on the
troubleshooting of equipment/machines that breakdown. Below are some minor
troubleshooting activities that are undertaken:

1. Replacement of the defective parts of equipment like can sealer, pressure
cooker, gas stove and gas range, etc.
2. Replacement of the missing parts of a can sealer, pressure cooker, gas range,
gas stove, etc.
3. Replacement of defective or malfunctioning electrical cords, plugs and switch of
electrically operated equipment like freezer, refrigerator, smokehouse, fish
scalers, blenders, poly sealers, etc.
4. Applying lubricant to machine parts that are slightly undergoing corrosion or wear
and tear.
5. Replacement of machine parts with cracks or leaks.
6. Replacement of leaking pipes in equipment requiring hydraulic fluid.
Performing Minor Preventive Maintenance
Preventive Maintenance is a system of maintenance that aims to minimize or
eliminate breakdown in equipment and machinery by a program of regular inspection and
repairs. This is done make sure that all equipment machines in the food processing plant
are always in good condition and ready for use anytime. Regularly inspecting the condition
of equipment/machines and promptly repairing those ones that breakdown will guarantee
that the processing of food will be smoothly undertaken as required by the company thus,
eliminating or minimizing the occurrence of accidents or faulty operation of
equipment/machines. It is important to remember, however, that the preventive
maintenance activities to be undertaken must be in conformity with manufacturer’s
specification and in line with company’s policy.
The following are some minor preventive maintenance done with
equipment/machines:
1. Checking the switch, plugs and electrical cords of electrically operated
equipment.
2. Checking the parts of some equipment/machines to determine if there are
defects, wear and tear, cracks, leaks, rusts or corrosion.
3. Checking the equipment/machine thoroughly to make sure that all parts are
intact. Missing parts will cause the equipment/machine to malfunction.
4. Cleaning, sanitizing and stowing all equipment/machines according to
manufacturer’s specifications and workplace policies and regulations.
5. Regularly checking and inspecting main machine parts to guarantee that the
machine is in top shape or condition.
6. Checking the condition of the machine and classify them as:
a. Serviceable
b. Repairable
c. Defective
7. Applying lubricants like oil and grease that undergo corrosion and friction to
prevent or minimize wear and tear of rubbing surfaces.
8. Checking machine temperature, hydraulic fluid, vibration, etc.
9. Performing proper cleaning, care and sanitation.
Below are examples of how some equipment/ machines are properly maintained or
cared for:

The Pressure Cooker
1. Thoroughly wash with soap and hot clean water then drain completely before and
after use.
2. Lubricate the metal – to – metal seal with cooking oil, petroleum jelly, Vaseline,
etc. to prevent the cover from scratching or sticking. Check this seal from time –
to – time during the canning process to be sure sufficient lubrication is present.
Apply a thin film of lubricant to the edge inside the cooker where the inside wall
begins to bevel.
3. Apply lubricant on the threads of the bakelite wing nuts; wipe away excess
lubricant.
4. Always keep safety openings clear to make sure steam can pass through them.
5. Before and after using the cooker, clean the vent pipe by carefully inserting a thin
piece of wire in the vent and run it gently in and out to be sure it is clear and
unobstructed. Rinse with hot water.
6. Do not subject the cooker to sudden extreme temperature changes as this will
cause expansion or contraction which can crack the cast aluminum pressure
cooker. Do not add cold water to a cooker that boiled dry or cool a hot cooker
suddenly by pouring cold water or wrapping it with wet cloth.
7. If you ever drop the cooker, it must be examined for damage.
8. Periodically wipe – off the metal – to – metal seal with a clean towel to remove
any build – up of hardened lubricant. Avoid hard scrubbing of the metal – to –
metal seal to prevent damage.
9. Prevent discoloration by scrubbing with an aluminum cleaner or soap
impregnated steel wool cleaning pad. Pitting of the cooker is prevented by
washing, rinsing, and drying the unit thoroughly every after use.
10. Always store the cooker in a dry area when not in use. The cover should be
stored separately from the cooker or upside down on the cooker to allow air
circulation. Always be sure cover and cooker are thoroughly dry to protect
against pitting and corrosion.
11. Protect the metal – to metal seal from being struck and dented.
The Can Sealer
The parts of an automatic manual can sealer are easier to dismantle and assemble
as compared with the automatic electrically operated sealing machine. However, when
dismantling or assembling the parts of the can sealer, careful handling is required to make
sure all parts are properly in place and not a single part is misplaced or lost. Before
assembling the parts, these must be done:
1. Check that all parts are present.
2. Lubricate parts that rub each other to prevent friction that leads to wear and tear
of surfaces.
3. Lubricate the crankshaft, the seaming head, bevel gears, clamp, etc. Wipe away
excess lubricant.
4. Wash the chuck and the base plate after sealing tin cans with soap and clean
water to remove oil, sauce and brine that spilled on them. Rinse thoroughly.
Wipe dry with a clean towel.
5. Store in a clean dry place.
6. Replace all damaged, missing or defective parts.

The Freezer
1. Use the freezer in accordance with purpose described in the user’s manual.
2. Properly install the freezer in accordance with installation requirements.
3. Switch control to OFF before unplugging.
4. Unplug the freezer before cleaning, before repairing any parts by a qualified
repairman.
5. Always grip plug firmly and pull straight out from the outlet, when unplugging.
6. When moving the freezer away from the wall, be careful not to roll over or
damage the power cord.
7. Immediately repair or replace all electric service cords that have become frayed
or otherwise damaged. Do not use a cord that shows cracks or abrasion damage
along its length or either the plug or connector end.
8. After the freezer is in operation, do not touch the cold surfaces, particularly when
hands are damp or wet. Skin may adhere to these extremely cold surfaces.
9. Operate freezer away from explosive fumes.
10. Refrain from using electrical devices or sharp instruments in defrosting your
freezer.
11. The freezer must be properly grounded when installed.
12. Defrost regularly.
13. Clean the interior to prevent food from being contaminated during storage.
Remove detachable parts and wash in warm water and baking soda solution
(Use 1 tablespoon of baking soda per liter of water). Follow the same procedure
for cleaning the door gasket, wire basket, and all plastic parts.
14. Clean exterior surfaces with warm water and dish washing detergent. Dry and
polish with a soft cloth. Do not wipe with soiled dish washing cloth or wet towel.
This may leave residue that may corrode the paint. Do not use scouring pads,
bleach or cleaners because they scratch and weaken the paint finish.
15. In case of brownouts, turn the temperature control to OFF and unplug your
freezer to avoid OVERLOADING your compressor when power is restored.
The Refrigerator
The refrigerator which has an automatic defroster should be thoroughly cleaned
every week by wiping off containers of food and removing all foods that cannot be used.
Refrigerators which do not have automatic defrosters should be
defrosted whenever the frost on the frosting unit is over ¼ inch thick. When caring for your
refrigerator follow the procedure below:
1. Wipe up spilled food immediately.
2. Wash inside shelves and trays at least twice a week with 1 table spoon baking soda
dissolved in 1 liter clean water.
3. Rinse and dry thoroughly.
4. Flush drains/defrost weekly.

When defrosting the refrigerator follow these steps:
1. Turn off the electric current.
2. Remove all ice trays and frozen foods from the freezing unit.
3. Wrap frozen foods in newspaper to keep them from thawing.
4. Put the drip tray in the proper place to catch the melted ice.
5. Place pans of hot water in the lower part of the freezing unit. Allow the ice to melt.
Never use a sharp or pointed object to remove the ice.
6. Remove the food in the lower part of the refrigerator.
7. Wipe the inside portion of the freezing unit as well as the refrigerator with water to
which 1 teaspoon baking soda has been added for each quart.
8. Turn on the current and return the food to the refrigerator.
Proper use the refrigerator by following these steps:
1. Study the booklet which is supplied by the manufacturer.
2. Keep the temperature between 35ºF and 45ºF.
3. Allow the food to cool before putting it in the refrigerator.
4. Open the door only when absolutely necessary and keep it open as short a time as
possible.
5. Put leftovers in small dishes and use them as soon as possible to avoid
overcrowding the refrigerator.
6. Remove food from paper bags before storing in the refrigerator.
7. Do not store unopened cans of food in the refrigerator unless they are to be chilled
for the next meal.
8. Store foods in covered dishes or glass jars to prevent odors from spreading.
9. Avoid getting grease on the gasket around the door.
10. Decide on a definite place in which to keep each kind of food, and put the foods in
the same places each time so that you will not waste time in looking for them.
The Gas Range and Gas Stove
In caring for your cooking equipment, follow the steps below:
1. Remove all burnt sediment and wipe grease from top of stove after each use
2. Scrape grease from cracks, openings, and hinges.
3. When cool, wash top of stove.
4. Keep burners clean. Gas burners can be soaked and scrubbed with a stiff brush.
5. Wipe with a clean cloth dipped in a sanitizing solution.
Use and Care of the Gas Range and Gas Stove
When using the range, remember to:
1. Use utensils that are large enough to prevent the boiling food from spilling over the
range top or oven;
2. Keep a dish on the range top for the spoon that you use in stirring food;
3. Avoid putting anything hot on porcelain enameled surfaces or putting cooking
utensils across them the heat may cause the surface to chip or crack;
4. Arrange pans in the oven so that the air can circulate around them; and
5. Wipe the chromium trimming with a damp cloth and polish it with a dry cloth.

Cleaning the Top of a Gas Range and a Gas Stove
1. Remove the burners and the rack and scrub them with warm, soapy water and
scouring pad.
2. Clean the holes with a hair pin or wire. Do not use a toothpick.
3. Rinse with clear, hot water, and dry the rack; turn the burners of the oven upside
down.
4. Return the burners and the rack to the range as soon as they are dry.
Note: Be sure the hose or pipe where the gas will pass don’t have leaks.
Cleaning the Units of an Electric Cooking Range
1. Turn on the high heat so that any food on the units will burn off.
2. Cool, and then brush each unit with a soft non-metallic brush. Never clean the unit
with a metal brush, a fork, a knife, or a sharp metal tool.
3. Use steel wool or a cloth for units which are enclosed.
The Oven
Follow these steps when cleaning your oven:
1. Use a pancake turner to remove food immediately after it has spilled on
on the oven.
2. Clean the oven thoroughly with a special cleaner when it is cool.
3. Wipe the oven with soapy water. Rinse with clean water and dry.
4. Turn on the oven for a few minutes to dry all parts so that they will not rust.
5. Be sure the gas tank and hose do not have any leaks.
Reporting the Breakdown of Equipment/Machine, Tools and Utensils
The person in charge of inspecting and checking equipment/machines used in
processing foods like fish, meat, fruits and vegetables must make the necessary report
regarding the breakdown of equipment/machine, tools and utensils and furnish the report to
the person responsible in scheduling the trouble shooting and repair of any
equipment/machine, tools and utensils that breakdown. In preparing such report, it is
necessary to follow the prescribed format required by the company or organization. This is
done to rigidly monitor the condition of all equipment/machines to ensure their serviceability
in accordance with workplace rules and regulations. Through the prepared reports, a
conclusion as to the condition of equipment/machines can be accurately made as to: a)
serviceable, b)repairable and c) defective. The compiled reports will provide a ready
database as to the needs of the company in terms of:
1. machine parts to be purchased
2. expenditures incurred for repair and purchase of machine parts
3. labor requirement for preventive maintenance and trouble shooting

A Sample Report on Equipment/Machine Breakdown
Daily Inspection Report Date:
Remarks
and
Condition
Before
Operation
During
Operation
After
Operation
Recommen
dations
Can Sealer
Pressure Cooker
Mechanical/Electric
Smokehouse
Freezer
Refrigerator
Electric Scaler
Oven
GasRange
Gas Stove
Food Processor/Blender
Juice Extractor
Vacuum Packer
Electric Polysealer
Inspected by:_______________________
Reviewed by: _______________________
The use of appropriate equipment in top condition is of primary importance in the
production of good food. Standardized equipment, a variety of knives, the right kitchen tools,
utensils, and appliances all contribute to the production of processed food with an excellent
quality.

It is therefore important to religiously conduct post operation activities to make sure
that equipment/machineries are properly inspected, checked, cleaned and sanitized and
subjected to preventive maintenance in accordance with manufacturer’s specification and
company policies.
The Preventive Maintenance to be performed includes checking the following:
1. Machine temperature
2. Hydraulic fluid
3. Wear and surface condition
4. Crack
5. Leak detection
6. Vibration
7. Corrosion
8. Electric insulation
Fill in the blanks
1. ____________________to test the accuracy; to examine something in order to
establish its state or condition.
2. ______________________is mechanical failure causing a machine or equipment to
malfunction.
3. _____________________a break or fissure on some parts of an equipment as in the
body of a pressure cooker.
4. _____________________ death or execution from electric shock.
5. _____________________to carefully examine a machine or equipment in order to
determine maintenance to undertake..
6. ____________________a substance like oil or grease that coats or treats a machine
to lessen friction and the wear and tear of machine parts due to constant rubbing of
surfaces.
7. ___________________a system of maintenance that aims to minimize or eliminate
breakdown in equipment and machinery by a program of regular inspection and
repairs.
8. __________________to restore a machine or equipment that breaks down into good
order or condition.
9. __________________electrical device having two (2) states, ON (closed) OFF
(open).
10._________________ to turn off an electrical device.
Self-Check 3.1

Perform Preventive Maintenance of Can Sealer and Pressure Cooker
Equipment, tools and materials needed:
 can sealer
 pressure cooker
 gas stove
 table
Procedures:
The Pressure Cooker
1. Thoroughly wash with soap and hot clean water then drain completely before
and after use.
2. Lubricate the metal – to – metal seal with cooking oil, petroleum jelly,
Vaseline, etc. to prevent the cover from scratching or sticking. Check this
seal from time – to – time during the canning process to be sure sufficient
lubrication is present. Apply a thin film of lubricant to the edge inside the
cooker where the inside wall begins to bevel.
3. Apply lubricant on the threads of the bakelite wing nuts; wipe away excess
lubricant.
4. Always keep safety openings clear to make sure steam can pass through
them.
5. Before and after using the cooker, clean the vent pipe by carefully inserting a
thin piece of wire in the vent and run it gently in and out to be sure it is clear
and unobstructed. Rinse with hot water.
6. Do not subject the cooker to sudden extreme temperature changes as this will
cause expansion or contraction which can crack the cast aluminum pressure
cooker. Do not add cold water to a cooker that boiled dry or cool a hot cooker
suddenly by pouring cold water or wrapping it with wet cloth.
7. If you ever drop the cooker, it must be examined for damage.
8. Periodically wipe – off the metal – to – metal seal with a clean towel to
remove any build – up of hardened lubricant. Avoid hard scrubbing of the
metal – to – metal seal to prevent damage.
9. Prevent discoloration by scrubbing with an aluminum cleaner or soap
impregnated steel wool cleaning pad. Pitting of the cooker is prevented by
washing, rinsing, and drying the unit thoroughly every after use.
Operation Sheet 3.1

10. Always store the cooker in a dry area when not in use. The cover should be
stored separately from the cooker or upside down on the cooker to allow air
circulation. Always be sure cover and cooker are thoroughly dry to protect
against pitting and corrosion.
11. Protect the metal – to metal seal from being struck and dented.
The Can Sealer
The parts of an automatic manual can sealer are easier to dismantle and assemble
as compared with the automatic electrically operated sealing machine. However, when
dismantling or assembling the parts of the can sealer, careful handling is required to make
sure all parts are properly in place and not a single part is misplaced or lost. Before
assembling the parts, these must be done:
a. Check that all parts are present.
b. Lubricate parts that rub each other to prevent friction that leads to wear
and tear of surfaces.
c. Lubricate the crankshaft, the seaming head, bevel gears, clamp, etc.
Wipe away excess lubricant.
d. Wash the chuck and the base plate after sealing tin cans with soap and
clean water to remove oil, sauce and brine that spilled on them. Rinse
thoroughly. Wipe dry with a clean towel.
e. Store in a clean dry place.
f. Replace all damaged, missing or defective parts.
Precautions:
1. Wear appropriate protective outfit when working.
2. Proper care in handling the equipment.
3. Check accuracy of the equipment.

Performance Criteria 3.1Checklist for
Operation Sheet
Perform Preventive Maintenance of Can Sealer and Pressure Cooker
1.performed the task on maintaining the equipment(can
sealer and pressure cooker)?
2. conducted the important preventive maintenance of the
equipment?
3. possessed the knowledge and skills in performing post-
operation activities after using the equipment?

Congratulations! You did a great job! Rest and
relax a while then move on to the next lesson.
Good luck!
LO1
 CBLM – Fish Processing II, page 11
 http://www.grapestompers.com/articles/refractometer_use.asp
LO 2
 CBLM – Fish Processing II, page 11
 http://www.grapestompers.com/articles/refractometer_use.asp
REFERENCES

Perform Mathematical Computations
LESSON 2
LO1. Gather and tabulate the recorded data relevant to processed
production.
LO2. Review various formulations.
LO3. Calculate the production input and output.
LO4. Compute the costs of production.
LEARNING OUTCOMES:
do the following:

Concentration of a solution the amount of solute present in a given quantity
of solvent.
Conversion a change from one state or position to another
or from one form to another.
Cost the total amount spent for goods or services
including money, time, and labor
Data a collection of information about a study under
investigation. It may be a number (quantitative)
or a word (qualitative).
Documentation a systematic procedure of producing a record
for reference.
Input something that enters a process from the
outside and is acted upon or integrated in the
main body of data.
Measurement a way of comparing certain attribute of an
object with some given standard.
Output anything produced especially through a
process, a product, or a yield.
Production cost the combined cost of raw materials and labor
incurred in producing goods.
Production Report a written record showing the input – output
relationship in determining the yield from a
certain procedure.
Raw food cost the amount spent for buying raw ingredients.
Recording the process of capturing data or translating
information to a recording format stored on
some storage medium, which is often referred to
as a record
Semi-permeable membrane a material that allows molecules of one kind to
pass through it but prevents the passage of
other kinds of molecules.
Solution a homogenous mixture of substances with
variable composition.
Tabulate to count, record, or list systematically.
Definition of Terms

Gather and tabulate the recorded data relevant to processed food
production.
LEARNING OUTCOME 1
1. Records of weights and measurements of raw materials and ingredients
are gathered and summarized according to workplace standard operating
procedure.
2. Records of weights and measurements of finished processed products are
gathered and summarized according to workplace standard operating
procedures.
3. Summarized data are tabulated according to enterprise requirements.

Multiple Choice:
Directions: Carefully read the questions and choose your answer from the options given.
Write your answers in your answer sheet.
1. How many teaspoons are there in one tablespoon?
A. 2 B. 3
C. 4 D. 5
2. How many tablespoons are there in one cup?
A. 13 B. 14
C. 15 D. 16
3. Which of the following is equivalent to one kilogram?
a. 1500 g B. 1000 g
c. 2000 g D. 2500 g
4. What is the equivalent of 320
F to Centigrade?
A. 00
C B. 20
C
C. 10
C D. 30
C
5. What do you call a form with only a few data presented?
A. tabular form B. textual form
C. graphical form D. none of the above
.
Pretest LO 1
Let us determine how much you already know about the gathering and
tabulating the recorded data relevant to processed food production . Take
this test.

LO1. Gathering the Record of Weights and Measurement of Ingredients and Materials
Not a day passes without any of us taking certain measurements. You measure the
time it takes you to solve problem in STVEP. The meat dealer measures the amount of pork
your mother buys with P 100.00. Your sister measures the flour she needs for her cake
recipe. Even infants get a share of measurement through the amount of milk formula given
them everyday, not to mention the fact that their growth is measured by their gains in weight
and height.
What do you really do when you take measurements? For instance, when you take
your weight, you use a weighing scale. You keep a record of your weight, trying to find out
how much you have gained or lose.
Mass is the amount of material an object has. The base unit of mass is gram (g).
For heavier mass, the unit used is the kilogram(kg).
Volume is the amount of space something occupies. The unit used for measuring
the volume of liquid is the litre. (L).
Capacity refers to how much a container can hold.
Temperature refers to the degree of hotness or coldness of a body. The metric unit of
temperature is degree Celsius (0
C). In the Celsius Scale, 00
C is the freezing point of water,
and 1000
C is the boiling point of water. The instrument used for measuring temperature is
the thermometer. Another unit of temperature is degree Fahrenheit (00
F).

Measurements and Conversions
It is important to weigh or measure all ingredients accurately, especially for
beginners. There are cooks and chefs who seem to be able to produce good results by
guesswork and intuition because of their long experience in cooking. However, that should
not be the case. What generally matters is using precise measurement.
When weighing things, it is essential to buy a good brand of weighing scale that
would longer. A good selection of measuring cups and spoons (as listed below) can be very
handy.
a. Measuring Cups
 1 Cup (C)
 1/2 C
 1/3 C
 1/4 C
 1/8 C
b. Measuring Spoons
 1 Tablespoon (tbsp or T)
 1 Teaspoon (tsp or t)
 1/2 tsp
 1/4 tsp
A clear glass measuring cup is necessary to get precise liquid measurements.
Dry Ingredients - The most important thing to know about measuring dry ingredients
is that they should be level with the top of your measuring cup. Dip your cup into the bin, fill
to overflowing and level it off by sweeping the edge of a knife across the top. Spoon flour
and similar ingredients into measuring cups. Do not scoop the ingredient using the cup itself
because this “packs” the cup too much and the measurement won’t be precise. Be careful if
you are using a cup larger than what is needed (as in a 1 cup measure to get 1/2 C worth of
ingredients). The same leveling technique should be used with measuring spoons.
Tips : Measure dry ingredients over a plate or bowl so you can catch the excess and
put it back in the container.
Most ingredients don't need to be packed into the measuring cup. Granulated sugar
does it for you. Flour should actually be aerated or fluffed up before measuring. Brown
sugar is one exception, if you want to pack down while measuring in order to get the
proper amount.
Measure liquids at eye level. In other words, place the cup on a flat surface and
crouch down so your eyes are at the same level as the cup in order to check the accuracy of
the amount in the cup.
To measure solid fats (shortening, butter etc.) : Most butter has measurements
listed on the wrapper, so you can simply cut off the amount you need. If that information is
not available, to measure fats accurately, pack them down in the cup to get rid of air pockets.
It’s easier to pack fats at room temperature. Another method that works well for butter and

especially shortening is water displacement (this works for any fraction of a cup
measurement). For instance, if you need 1/2 C shortening fill a 1 cup measure 1/2 full with
water. Carefully add shortening to the cup until the water reaches the top of the cup. Drain
the water and use the shortening.
Weight Measurements and Conversions
Abbreviation Long
c cup
gal gallon
gm gram
kg kilogram
lb pound
ml mililiter
oz ounce
pt pint
qt quart
tbsp
tablespoon
tsp teaspoon
fl. oz. fluid ounce
Weight Conversion Factors
Multiply By To Get
Grams (gm) 0.035 Ounces
Grams 0.0022 Pounds
Grams 0.001 Kilograms
Kilograms (kg) 2.21 Pounds

Approximate Metric Equivalent by Weight (US-Metric)
U.S. Metric
¼ ounce (oz) 7 grams (g)
½ ounce 14 grams
1 ounce 28 grams
1 ¼ ounces 35 grams
1 ½ ounces 40 grams
2 ½ ounces 70 grams
4 ounces 112 grams
5 ounces 140 grams
8 ounces 228 grams
10 ounces 280 grams
15 ounces 425 grams
16 ounces (1 pound) 454 grams
Liquid Measurements and Conversions
Kilograms 1000 Grams
Pounds (lb) 453.6 Grams
Pounds 0.4536 Kilograms
Pounds 16 Ounces
Ounces (oz) 0.0625 Pounds
Ounces 28.3 grams
tsp. Tbsp. fl.oz gill cup pint Quart gallon
1 teaspoon =
1 1/3 1/6 1/24

US Customary
System
Spoons
fluid
oz.
Approx.
mililiters
1/16 cup (c) = 1 tablespoon (tbsp) = 3 teaspoons (tsp)
1/2
fl.oz
15 ml
1/8 cup = 2 tablespoons 1 fl.oz. 30 ml
1/6 cup = 2 tablespoons + 2 teaspoons
1.3
fl.oz
40 ml
1/3 cup = 5 tablespoons + 1 teaspoon
2.7
fl.oz
80 ml
2/3 cup = 10 tablespoons + 2 teaspoons
5.3
fl.oz.
155 ml
1 cup = 16 Tablespoons 8 fl.oz. 235 ml
1 3/4 cup =
14
fl.oz.
410 ml
1 tablespoon = 3 1 1/2 1/8 1/16
1 fluid ounce = 6 2 1 1/4 1/8 1/16
1 gill = 24 8 4 1 1/2 1/4 1/8
1 cup = 48 16 8 2 1 1/2 1/4 1/16
1 pint = 96 32 16 4 2 1 1/2 1/8
1 quart = 192 64 32 8 4 2 1 1/4
1 gallon = 768 256 128 32 16 8 4 1

2 cups = 1 pint =
16
fl.oz.
470 ml
3 cups =
24
fl.oz.
700 ml
4 cups = 1 quart =
32
fl.oz.
940 ml
MISCELLANEOUS EQUIVALENT
1 pinch 1/8 teaspoon or less
1 teaspoon 60 drops
1 dessertspoon (UK) 2 teaspoons
Approximate liquid measurement conversion factors
Multiply By To Get
Quarts (qt) 0.95 liters
Quarts 4 cups
Liters (l) 1.06 quarts
Liters 1000 mililiters
Cups 235 mililiters
Cups 8 fluid ounce
Cups 0.25 quarts
Mililiters (ml) 0.0042 cups
Mililiters 0.067 tablespoons

Mililiters 0.034 fluid ounce
Fluid ounce (fl. oz) 29.6 mililiters
Fluid ounce 0.125 cups
Gallons (gal) 3.785 liters
Temperature Measurements and Conversions
To convert Degrees Celsius (Centigrade) °C to Degrees Fahrenheit (°F), multiply °C by
1.8 and add 32.
For example, to convert 100°C to °F,
100 x 1.8 + 32 = 212°F
To convert Degrees Fahrenheit (°F) to Degrees Celsius (°C), subtract 32 from °F first,
then multiply by 0.56.
For example, to convert 200°F to °C,
(200 - 32) x 0.56 = 94°C
Freezing point for water = 0°C = 32°F
Boiling point for water = 100°C = 212°F
Temperature Conversion Table
Fahrenheit Celcius Celcius Fahrenheit
32 °F 0°C 0 °C 32 °F
40 °F 4.4 °C 10 °C 50 °F
50 °F 10 °C 20 °C 68 °F
60 °F 15.6 °C 30 °C 86 °F
70 °F 21.1 °C 40 °C 104 °F
80 °F 26.7 °C 50 °C 122 °F

90 °F 32.2 °C 60 °C 140 °F
100 °F 37.8 °C 70 °C 158 °F
110 °F 43.3 °C 80 °C 176 °F
120 °F 48.9 °C 90 °C 194 °F
130 °F 54.4 °C 100 °C 212 °F
140 °F 60 °C 110 °C 230 °F
150 °F 65.6 °C 120 °C 248 °F
160 °F 71.1 °C 130 °C 266 °F
170 °F 76.7 °C 140 °C 284 °F
180 °F 82.2 °C 150 °C 302 °F
190 °F 87.8 °C 160 °C 320 °F
200 °F 93.3 °C 170 °C 338 °F
225 °F 110 °C 180 °C 356 °F
250 °F 120 °C 190 °C 374 °F
275 °F 135 °C 200 °C 392 °F
300 °F 150 °C 210 °C 410 °F
325 °F 165 °C 220 °C 428 °F
350 °F 175 °C 230 °C 446 °F
375 °F 190 °C 240 °C 464 °F
400 °F 205 °C 250 °C 482 °F
425 °F 220 °C 260 °C 500 °F
450 °F 230 °C 270 °C 518 °F
475 °F 245 °C 280 °C 536 °F

500 °F 260 °C 290 °C 554 °F
Summarizing and Tabulating All Raw Data Gathered
Any set of information or data collected for study should be organized and analyzed
systematically for easier and faster interpretation. To do this, collected data may be
presented in any of the following forms:
1. The textual forms are used when data to be presented are few.
2. The tabular and graphical forms are used when more detailed information is to be
presented.
Using tables and graphs has the following advantages:
1. Data are presented in a more practical and convenient way.
Instead of writing text on the information gathered, items can be enumerated in tabular form or
shown in graphical form.
2. Data can be compared more easily.
Recording tables and graphs can be done more easily because the needed
information can be seen at a glance.
3. Data can be analyzed comparatively.
Tables and graphs enable a thorough analysis of data because all needed
information is clearly known.
Example: (Textual Form)
Marinated Boneless Milkfish
Raw Materials:
Fresh milkfish - 1 kilogram
Vinegar - 1 cup
Calamansi juice - ½ cup
Soy sauce - ½ cup
Salt - 5 tablespoons
Sugar - 5 tablespoons
Black pepper - 1 tablespoon
Garlic (minced) - 1 tablespoon
Steps:
a. Weigh the fish.

b. Split them and remove the viscera, backbone and dorsal fin.
c. Wash the fish with freshwater.
d. Wash again the deboned milkfish and drain for 15 minutes.
e. Soak the deboned milkfish for 7 hours in marinated solutions composed of
vinegar, salt, sugar, soy sauce and spices.
f. Pack the boneless milkfish in plastic bags and seal.
g. Freeze them to be ready for market.
Recording Skills
In recording we need the following skills:
Accuracy
The measurement of any physical quantity is always subject to some degree of
uncertainty. There are several reasons for this: the limitation inherent in the construction of
the measuring instrument or device, the conditions under which the measurement is made,
and the different ways in which the person uses or reads the instrument.
One way to express the uncertainty of a measurement is in terms of accuracy.
Accuracy refers to the closeness of a measurement to the accepted value for a specific
physical quantity. It is expressed as either an absolute or a relative error. Absolute error is
the actual difference between the measured value and the accepted value.
Relative error is expressed as a percentage and is often called percentage error. It is
calculated as:
Er – Ea
A x 100%
Er- relative error
Ea – absolute error
A - accepted value
Precision
In common usage accuracy and precision are often used synonymously. But in
science it is important to make a distinction between them. You should learn to use the two
terms correctly and consistently. Precision is the agreement among several measurements
that have been made in the same way.
The precision of your laboratory measurements will be governed by the instruments
at your disposal. In a measuring instrument the degree of precision obtainable is called the
tolerance of the device. Any figure listed for the tolerance of an instrument indicates the
limitations of the instrument. It is assumed that the instrument is used properly and that
human errors are held to a minimum.
Data Gathering Skills

When you want to know whether several boxes of preserving bottles are free from
defects, it would be time consuming to examine all of them piece by piece. How can you
facilitate the quality test?
You can do this by examining a few samples from each box. This process is called
sampling and the defined set of that sample is called population.
When for example, a housewife buys a cavan of rice, she examines only a handful of
rice from the cavan to find out whether it is of good quality or not.
 The handful of rice is called the sample.
 The cavan of rice from which the sample is taken is called population.

Direction: Complete the list of measurement and conversions. Use extra paper for your
computation. Write the answer in your answer sheet.
1. 1 quart = _________cups
2. 12 tbsp. = _________ cup
3. 1 lb. = _________ grams
4. 14 grams = ________ once
5. 1 pint = ________ tbsp.
6. 1 tbsp. = ________ tsp
7. 1 cup = ________ tbsp
8. 1 pinch = ________ tsp.
9. 2.5 kg = ________ grams
10. 102.1 o
F = ________ o
C
Self-Check 1.1

Presenting Data by Textual Form
Procedure:
Example: (Textual Form)
Marinated Boneless Milkfish
Raw Materials:
Fresh milkfish - 1 kilogram
Vinegar - 1 cup
Calamansi juice - ½ cup
Soy sauce - ½ cup
Salt - 5 tablespoons
Sugar - 5 tablespoons
Black pepper - 1 tablespoon
Garlic (minced) - 1 tablespoon
1. Weigh the fish.
2. Split the fish and remove the viscera, backbone, and dorsal fin.
3. Wash the fish in fresh water.
4. Wash again the deboned milkfish and drain for 15 minutes.
5. Soak the deboned milkfish for seven hours in marinated solution of vinegar, salt,
sugar, soy sauce, and spices.
6. Pack the boneless milkfish in plastic bags and seal.
7. Freeze them, ready for market.
Activity Sheet 1.1

Activity Sheet 1.1
Presenting Data by Textual Form
1. collect and interpret the data systematically?
2. present the data in a more practical and convenient
way?
3. record the data accurately?

1. Raw materials and ingredients and percentage formulations are
checked/counter checked according to approved specifications and
enterprise requirements.
2. Finished products and percentage formulations are reviewed according to
approved specifications and enterprise requirements.
Review various formulations.
LEARNING OUTCOME 2

Multiple Choice
Directions: Write the letter of your answer.
1. A solution which has a uniform composition and property is
A. heterogeneous C. concentration
B. homogenous D. mixture
2. If you are asked to express concentration, which of these will you use?
A. weight of solute per unit of solvent C. proportion formulation
B. ratio D. per unit weight of solvent
3. In smoking fish, what ingredients and materials will you prepare and check?
A. salt and water C. both a and b
B. fish D. none of these
4.What is taken into consideration when preparing curing solution for salting?
A. method of salting C. species of fish
B. size of fish D. none of these
5.The ratio needed in brine cooking smoked fish is
A. 150g to 700ml C. 200g to 750ml
B. 250g to 800ml D. 300g to 850ml
Pretest LO 2
Let us determine how much you already know about reviewing formulation. Take
this test.

LO2. FORMULATION AND CONCENTRATION OF SOLUTIONS ACCORDING TO
SPECIFICATIONS AND STANDARDS OF THE ENTERPRISE
A solution is a homogenous mixture of substances with variable composition. The
substance present in the major proportion is called the solvent, whereas the substance
present in the minor proportion is called the solute. It is possible to have a solution
composed of several solutes. The process of a solute dissolving in a solute is called
dissolution.
Concentration
The concentration of a solution is defined as the amount of solute present in a given
quantity of solvent. The most common way to express concentration is on the basis of the
weight of solute per unit weight of solvent. For example, a salt solution may be prepared by
dissolving 1.64 grams of sodium chloride in 100 grams of water. The concentration of this
solution could also be expressed as 0.0164 grams of NaCl per 1 gram of water, or as 16.4
grams of NaCl per 1,000 grams of water. Thus, a statement of the concentration of a
solution does not imply anything concerning the amount of solute or the amount of solvent
present, but rather gives the ratio of solute to solvent in terms of some convenient (and
arbitrary) units. Because the weight of a sample of a liquid is usually more difficult to
determine experimentally than its volume, a practical unit of concentration is the weight of
solute in a given volume of the solution. For example, a sugar solution may contain 50
grams of sugar per 100 milliliters of solvent.
Ingredients and Materials to be Checked According to Approved Specifications and
Enterprise Requirements
For curing fish/salting fish:
Ingredients : Salt, water
fish
For smoking:
Ingredients : Salt, water
fish (bangus, galunggong, tilapia,
and herring family

For sugar concentrates
Ingredients : Sugar, calamansi or citric acid
fruit (mango, guava, pineapple)
For fermentation:
Ingredients : Salt
dilis and alamang
Various Formulations and Concentrations of Solutions
 Salting/Curing:
The ratio of salt to fish depends on the method of salting to be applied to the fish. If
kench salting is used, the ratio is 1:7 by weight wherein one part of salt is added to seven (7)
parts of fish. If brine salting is used, the ratio is 1:4 by weight wherein one part of salt is
added to four (4) parts of fish. In dry salting to make brine, you use 1:3 by weight or you add
one part of salt to three (3) parts of fish.
 Sugar concentrate:
The ratio of fruit juice or pulp to sugar depends on the degree of the pectin content of
the fruit. If the pectin is good, the ratio is 1:3/4 wherein one part of fruit juice or pulp is mixed
to three fourths (¾) part of sugar. If the pectin is not good, the ratio is 1:1 wherein one part
fruit juice or pulp is mixed with one part of sugar.
 Smoking:
The ratio of salt to water for brining and brine cooking is 250 grams of salt to 800ml
water.

Directions: Read carefully the sentences. Then identify the word being describe in each
sentence and write it in a blank before the number.
__________________1. It is the amount of solute present in a given quantity of solvent.
__________________2. It is the total amount spent for goods or services including money
and time and labor.
__________________ 3. It is the cost of raw ingredients.
__________________ 4. It refers to the combined costs of raw material and labor incurred
in producing goods.
__________________ 5. It is a material that allows molecules of one kind to pass through
it but prevents the passage of other kinds of molecules.
__________________ 6. It refers to the homogenous mixture of substances with variable
composition.
__________________ 7. It is a solution which has a uniform composition and property.
__________________ 8.Is the normal range in the percentage of food cost.
__________________ 9. It is a solution of salt and water wherein fish is soaked and
cooked before finally smoking it.
__________________ 10. It is the process of a solute dissolving in another solute.
Self-Check 2.1

Multiple Choice
Directions: Read carefully the questions. Choose the answer from the options given.
Write the letter only in your answer sheet.
1. If you buy ¼ kilo of sugar to be used in pickling how much is this in grams?
a. 250 g b. 270 g
c. 260 g d. 280 g
2. You are instructed to process fermented fish. What is the ratio needed to
ferment fish and salt by weight?
a. 1:4 b. 1:5
c. 1:6 d. 1:7
3. In smoking fish, how many grams of salt is equivalent to one cup?
a. 250 g b. 270 g
c. 260 g d. 280 g
4. In your laboratory room, your group leader asks you to prepare the mixture for
mango jam. What is the proportion needed?
a. 1:1 and 1:3/4 b. 1:2 and 1:1/2
c. 1:2 and 1:2 d. 1:1 and 1: 1/4
5. Using 1:3 ratio in salting fish, how many grams of salt is needed to salt the fish
weighing 900 grams?
a. 300 g b. 400 g
c. 500 g d. 200 g
HowDo You ExtendWhatYouHaveLearned?

Calculate the production input and output.
LEARNING OUTCOME 3
1. Data on actual spoilage and rejects and corresponding percentage
equivalents are calculated according to enterprise requirements.
2. Data on actual yields and recoveries and corresponding percentage
equivalents are calculated according to enterprise requirements.
3. All calculated data are recorded according to enterprise requirements.

Multiple Choice
Directions: Read carefully the questions. Choose the answer from the options given.
Write the letter only in your answer sheet.
1. If you buy ¼ kilo of sugar to be used in pickling how much is this in grams?
a. 250 g b. 270 g
c. 260 g d. 280 g
2. You are instructed to process fermented fish. What is the ratio needed to
ferment fish and salt by weight?
a. 1:4 b. 1:5
c. 1:6 d. 1:7
3. In smoking fish, how many grams of salt is equivalent to one cup?
a. 250 g b. 270 g
c. 260 g d. 280 g
4. In your laboratory room, your group leader asks you to prepare the mixture for
mango jam. What is the proportion needed?
a. 1:1 and 1:3/4 b. 1:2 and 1:1/2
5. Using 1:3 ratio in salting fish, how many grams of salt is needed to salt the fish
weighing 900 grams?
a. 300 g b. 400 g
c. 500 g d. 200 g
Pretest LO 3
Let us determine how much you already know about calculating the production
input and output . Take this test.

LO3. Calculating Data on Raw Materials or Ingredients Consumption and
Corresponding Percentage Equivalent in Line with Enterprise Requirement
Data gathering on raw materials and ingredients is necessary in order to compute
and calculate production input and output of the finished product. The following are
examples of data that are gathered based on the products to be done.
1. Pickled Mixed Vegetables
Data: Item Weight
Sugar 250 g
Vinegar 250 ml
Salt 15 g
Carrots 150 g
Sayote 250 g
Bell pepper 75 g
Garlic 50 g
Ginger 50 g
Onion 75 g
2. Smoked Fish
Data: Item Weight
Bangus 1 kg
Salt 250 g
Water 800 ml

3. Mango Jam
Data: Item Weight
Mango pulp 1 cup
Sugar 1 or ¾ c
Calamansi juice 1 tsp
4. Fermented fish
Data: Item Weight
Fish or alamang 4 kilos
Salt 1 kilo
5. Pickled Fish
Data: Item Weight
Fresh milkfish 1 kilogram
Vinegar 1 cup
Calamansi juice ½ cup
Soy sauce ½ cup
Salt 5 tbsp
Sugar 5 tbsp
Black pepper 1 tbsp
Garlic (minced) 1 tbsp
ACTUAL SPOILAGE/REJECTS
Actual spoilage rejects and their corresponding percentage depend on the product to
be made.
For example, in mango jam, spoilage refers to the peel of mango and seeds. The
products left during packing are not classified as spoilage rejects. In pickled fish, the skin of
the calamansi, garlic and the intestinal organ of fish are included in the spoilage. In smoked
fish, the intestinal organ is the reject. Lastly, in fermented fish and other fishery product,
small seashell, small stone and seaweeds are the spoilage.
ACTUAL YIELD AND RECOVERIES
Yield refers to the number of finished products after computing for the production
output and input.

Formula for getting the percentage yields
% Yield production input
production output
Record’s Calculated Data
Report/records based on the data gathered and computed on production output,
input, actual spoilage, rejects, actual yields or recoveries are kept for documentation
purposes. This will be the basis for determining the progress of whatever products to be
done on process.
Direction: Identify the following. Write your answer on the space provided for.
1. _____________________ refers to the number of finished products after computing for
the production output and input.
2. ______________________ is the proportion applied in preparing mango jam.
3. _____________________ is the ratio by weight of salt to fish in fermentation.
4. ____________________ is the weight of 1 cup salt in grams.
5. ____________________ is the ratio applied in dry salting to make brine.
Self-Check 3.1
X 100%

Compute the costs of production.
LEARNING OUTCOME 4
1. Costs of production are computed according to standard
procedures
2. Computed costs of production are reviewed and validated
according to enterprise production requirements.

Multiple Choice
Directions: Choose the word or words that is described in each sentence. Write the letter
only in your answer sheet.
1. It is a systematic procedure of producing a record for reference
A. output C. documentation
B. production report D. input
2. It is something that enters a process from the outside and is acted upon or integrated
in the main body of data.
A. production report C. input
B. output D. documentation
3. Anything produced especially through a process; a product; a yield.
A. documentation C. output
B. input D. production report
4. A written record showing the input – output relationship in determining the yield from
a certain procedure.
A. input C. production report
B. output D. documentation
5. It is the process of capturing data or translating information to recording format.
A. documentation C. production report
B. reporting D. output
Pretest LO 4
Let us determine how much you already know about computing the cost
production. Take this test.

LO4. IMPORTANCE OF RECORDING AND DOCUMENTING PRODUCTION INPUT
1. It gives us a reference data on the materials used together with their correct
magnitude.
2. It determines the economic viability of the product.
3. Records serve as a basis for planning.
4. Records greatly help in making right decisions.
Steps in recording and documenting production input are as follows:
First, weigh all materials and ingredients needed.
Second, make a necessary listing in your notebook of all the materials and
ingredients used. It is important to note how much or how many. This is what we call
recording or documentation.
Third, follow the correct format in documenting and recording.
Sample of Production Report
Product Name: Pickled / Marinated Milkfish
Production Date: February 26, 2012
Description of Materials:
Fresh Milkfish 1000 g
Other Ingredients:
Distilled vinegar 250 g
Calamansi juice 125 g
Soy sauce 125 g
Salt 75 g

Sugar 75 g
Black pepper 15 g
Minced garlic 15 g
Input: 1680 g
Output: Marinated Fish 1200 g
Wastage 480 g
Percentage Yield 71 %
Problem Encountered: NONE
Sample of Production Cost
Product: Pickled Mixed Vegetables
I – Raw Materials and Ingredients
Items Quantity wt/ml /gms Cost (P)
Chayote 3 kls. 3 000 gms. 60.00
Carrots 6 pcs. 550 gms. 30.00
red bell pepper 4 pcs. 80 gms. 5.00
Ginger 4 pcs. 270 gms. 10.00
Garlic 2 pcs. 100 gms 5.00
Onion 3 pcs. 165 gms 10.00
Sugar 1½ cups 275 gms 25.00
Vinegar 1½ cups 400 gms 10.00
Raisins 1 pack 100 gms 25.00
Salt 1 cup 150 gms 2.00
TOTAL 202.00

II. Packaging Materials
1. Preserving jars 8 pcs. x P 5. 00 = P 40. 00
2. Label 8 pcs. x P 1. 00 = P 8. 00
= P 48. 00
III. Overhead Expenditures
1. LPG / fuel for cooking P 2. 00
2. Tranportation P 7. 00
3. Water P 10. 00
= P 19. 00
Grand Total = P 269. 00
IV. Number of finished products - 8 jars
V. Net Weight - 250 gms
VI. Mark up price (20 % of Grand Total) - P 53. 80
VII. Selling Price - P 40.35

Matching Type
Directions: Match the item in column A with those in column B. Write the letters only.
A B
1. output a. something that enters process from the
outside and is acted upon or integrated in the
data
2. recording b. the end product or yield of a process
3. input c. a written record showing the input – output
relationship in determining the yield from a
certain procedure
4. production report d. a systematic procedure of producing a record
for reference
5. documentation e. the process of capturing data or translating
information to recording format
Self-Check 4.1

Prepare a Production Cost from the Given Format
Production Cost
Product:_________________________________
I – Raw Materials and Ingredients
Items Quantity wt/ml /gms Cost (P)
TOTAL
II. Packaging Materials
1. Preserving jars = P
2. Label = P _________
= P
Activity Sheet 4.1

III. Overhead Expenditures
1. LPG / fuel for cooking P
2. Tranportation P
3. Water P __________
= P
Grand Total = P ________________
IV. Number of finished products - ______________
V. Net Weight - ______________
VI. Mark up price (20 % of Grand Total) - P _____________
VII. Selling Price - P ____________

Activity Sheet 4.1
Preparing a Production Cost
1. record the spoilage and rejects of raw materials and
ingredients in preparing production report?
2. prepare a production cost based on the given format?

Good luck!
LO1
 CBLM – Fish Processing II, pp. 2 – 13
LO 2
LO 3
LO 4
REFERENCES

Interpret Plans and Drawings
LESSON 3
LO 1. Interpret lay-out plan and;
LO2. Perform outer packaging procedures
LEARNING OUTCOMES:
do the following:

Label – any tag, brand, mark, pictorial, or other descriptive written mater.
Layout – the way facilities are placed according to a plan.
Labeling – attaching of any printed materials to food products for identification.
Laminates – are made of two or more basic films held together by adhesives.
They provide better protection to food due to improved barrier properties.
Layout – the way facilitates are placed according to a plan.
Specification – a detailed itemized description of dimension plans, materials,
and other requirement.
Vacuum packaging – may be defined as taking of air from the container during
sealing in order to preserve the products.
Definition of Terms

Interpret lay-out plan
LEARNING OUTCOME 1
1. Lay –out plans of fish processing area are interpreted based on set
standards.
2. Signs and symbols are translated according to established standards.

Directions:
Read and understand the questions below. Select the best answer for each item and write
your choice on your answer sheet. Do not write anything on the module.
1.This processing activity involves pre-cooking.
A. storing C. preparation
B. receiving D. processing
2. This activity involves the final heat treatment during processing.
A. sterilizing C. preparation
B. storing D. labeling
3. This activity involves segregating suitable from unsuitable raw materials.
A. grading and sorting C. receiving
B. labeling D. preparation
4. The purpose of this activity is to give the correct information about the product
A. storing C. processing
B. labeling D. receiving
5. One purpose of this processing activity is to prolong the keeping quality of the finished
product.
A. labeling C. processing
B. storing D. preparation
Pretest LO 1
Let us determine how much you already know about interpreting lay-out. Take
this test.

LO1. ENUMERATE AND DESCRIBE THE FISH PROCESSING ACTIVITIES IN AN
ORDERLY MANNER.
Fish Processing Activities
1. Receiving. This activity includes sorting and grading of raw materials according to size,
species, and quality. It also includes segregating suitable from unsuitable ones.
2. Preparation. This includes the preparatory steps such as washing, eviscerating, cutting,
brining, and pre-cooking the fish by steaming, blanching, or broiling.
3. Processing/sterilizing. This activity involves the final processing and complete sterilization
of the processed finished product.
4. Storing. Storage room is provided for storing finished product such as canned/ bottled fish,
smoked fish, salted fish, pickled fish and other processed fishery products. Proper storage
will also extend the shelf life of the product.
5. Packaging. This processing activity involves the wrapping or enclosing food and fish
products in bottles or in cans for the purpose of protecting and preserving the finished
products.
6. Labeling. The purpose of this activity is to give the correct information about the product.

LAYOUT OF AN IDEAL PROCESSING ROOM

Directions: Identify the following. Write your answer on the space provided for.
1.__________________ includes washing, cooking.
2. __________________ involves the final heat treatment during processing.
3. __________________ involves segregating suitable from unsuitable raw materials.
4.___________________ is a processing activity which purpose is to give the correct
information about the product.
5. __________________ is done keeping quality of the finished product.
6. __________________ is a way of placing facilities according to a plan.
7. __________________ is an itemized description of dimension plans, materials, and other
requirements.
8. __________________ is attaching any printed materials to food products for identification.
9. __________________ is any tag, brand, mark, pictorial, or other descriptive written
matter attached to a product.
10. _________________ may be defined as taking of air from the container during sealing in
order to preserve the products.
Self-Check 1.1

=
Flowchart in the manufacture of smoked Bangus
Procedure:
1. Securing of raw materials
2.Preparing the raw materials
a. splitting
b. brining
c. pre-cooking
d. drying
3.Smoking
4.Cooling
5.Packaging
Legend:
Technology Process
Related Process
Temporary Delay
Activity Sheet 1.1

Activity Sheet 1.1
Flow Chart in the Manufacture of Smoked Bangus
1. identify the proper legend in preparing a flow chart?
2. enumerate the fish processing activities in an orderly
manner?

Perform outer packaging procedures
LEARNING OUTCOME 2
1. Fish products are packaged according to requirements and packaging
standard procedures.
2. Packaged fish products are labeled according to quality control standards

Directions:
Choose and encircle the letter of the correct answer.
1. Which of the following does not belong to the group?
A. polyvinylchloride C. polystyrene
B. expanded polystyrene D. polypropylene
2. Packaging material which is resistant to high temperature but poor quality in low
temperature and becomes brittle.
A. polyethylene C. polystyrene
B. polypropylene D. polyamide
3. Packaging material which is hard and glossy but grease resistant and brittle at all
temperatures.
A. polyamide C. polyvinylidine chloride
B. ethylene-vinyl chloride D. polyvinyl chloride
4. Packaging container which is effective in chilling fish because it can resist extreme heat
and can retain coldness inside.
5. Which of the following is optional label requirement?
A. nutrition facts C. vignette
B. ingredients D. expiry date
Pretest LO 2
Let us determine how much you already know about perform outer packaging
procedures. Take this test.

LO2. DIFFERENT PACKAGING MATERIALS FOR FISH PRODUCTS
Packing of fish and other products is defined as a wrapping or enclosure of fish and
other products in attractive and colorful materials for the purpose of protection and
preservation of products as well as to give eye appeal to the consumers / buyers.
Packaging protects the products from any form of loss, damage, deterioration, or
spoilage and contamination during handling and distribution.
Attractive package gives good eye appeal to the consumer / buyer. Good package
promotes good market of the product, thus, suitability and profitability of the product occur.
Packaging extends shelf-life of fishery products. For instance, vacuum - packed dried fish
will last for a year due to no oxidation. Good packaging materials serves as a medium of
communication to the consumer / buyer especially the complete information stated on the
label about the product. This eliminates high labor cost and improves marketing aspect. It is
also easy to handle, open, use, and dispose. Lastly. a good packaging material fits into the
cabinets, shelves, freezers, refrigerators, and other storage areas.
Different packaging materials for fish products.
1. Hard Plastics
Hard plastics are not flexible or elastic which are used for retail packaging in the
production of trays and form-fill packs of fishery products.
Likewise, hard plastics are light, durable, and resistant to corrosive substances and
water. They are manufactured using polystyrene, expanded polystyrene and polyvinyl
chloride ( Subansinghe, 1993).
Polystyrene. This is transparent and has low obstruction to water vapor and gases. When
treated with other materials like synthetic rubber, this can be easily shaped and molded with
pressure.

Expanded polystyrene. This is treated with polystyrene pellets wherein the pellets are
heated in steam to expand the material in order to produce a cellular shape. This is used for
tray molding.
Polyvinyl Chloride (PVC). There are two types of PVC, namely, plasticized and rigid.
Plasticized PVC are soft plastics and used in the making of films. Rigid PVC is hard and is
used in the production of trays due to its water proof and gas barrier properties.
2. Films
Films are web materials with thickness of 0.25mm. Materials more than 0,25 mm
thickness are called sheet. In choosing plastic films for packaging, the specific properties
such as tensile strength, puncture resistance, flex/crack resistance, water vaporand gas
barrier, clarity, and gloss and heat sealability (Hermes, 1998).
Films are classified into two groups, namely, basic and laminates. Basic films consist
of single layers film. Laminates contain two or more basic films glued or bonded together by
heat or adhesive (Hermes, 1998).
Basic Films.
Below are different types of basic films
1. Polyethylene (PE). PE is also called as polyethylene and used commonly due to its low
cost, relative strength and flexibility even at low temperature (Hermes, 1998). PE is heat
sealable but cannot be utilized in the manufacture of boil-in-bag pouches (Bremmer,
1985).
2. Polypropylene (PP). PP has better protective properties because it is resistant to high
temperature. However, it has poor qualities in low temperature and becomes brittle
(Pane and Pane, 1983).
3. Polyamide (PA). This is commonly called as nylon PA which is tough, grease-resistant,
less permeable to gases, and has a moisture permeability. It also possesses good
stretch properties and is stable over a wide range of temperatures, hence it can be used
in boil-in-bag pouches ((Hermes) 1998).
4. Polyester (PET). It has excellent gloss, low gas permeability, low moisture transmission,
high tensile strength, and can be used in a very wide range of temperatures up to
300°C. It is oftentimes laminated with polyethylene due to its poor heat sealing
properties (Kail. 1985).
5. Polyvinyl chloride (PVC).This is hard and glossy, but grease resistant and brittle at all
temperatures. Its film can be made into shrinkable forms with low temperature stability
by using special treatment methods (James, 1985).
6. Polyvinylidine chloride (PVDC). This is commercially known as saranor Cryovacs. This
is one of the most protective films because it is shrinkable and capable of withstanding
low freezing temperature. (Samuels, 1985).

7. Ethylene-vinyl acetate (EVA). This has good impact strength, good permeability and
high cling attributes. The material is used in the lamination of frozen products (Hermes,
1998).
Laminates
Laminates are made of two or more basic films held together by adhesives. They
provide better protection to food due to improved barrier properties. They are used in (1)
boil-in-bag, and (2) retort pouch pack.
1. Boil-in-bag. The suitable material in this type of container is modified
polyethylene with polyester or nylon lamination. This is commonly used for light
cooking fishery products.
2. Retort pouch pack. This is made from laminates of polyester/aluminum film and
polyolefine like polyethylene. The layers are bonded together with glue of high
performance. Its use is preferable due to less heat damage of texture and
nutrient.
Plastic Box Packaging Containers.
Plastic is used to characterize a wide range of materials like polyethylene and
polypropylene. High density polyethylene and polypropylene are widely used in the
manufacture of modern day containers (Subasinghe, 1993). Plastic box packaging
containers are classified into (1) polyethylene, (2) polypropylene, and (3) polystyrene or
styrophore.
1. Polyethylene. This is classified into low density (0.910 g/cm³ to 0.925g/cm³)
and high density. High polyethylene is divided into two types namely,
Type III with density of 0.941g/cm³ to 0.959g/cm³ and Type IV with density
of 0.960g/cm³ and above (Wheaton and Lawson, 1985).
By and large, polyethylene has excellent toughness being resistant to
chemicals, oil, and grease, inert to food, and has extremely low water
vapor transmission properties (Hermes, 1998).
Moreover, high density polyethylene containers are effective in the
chilling of fish. These containers can resist extreme heat and cold
because they can retain coldness inside.
2. Polypropylene. This has high resistance to grease and most chemicals,
provides a good barrier to water vapor, and can withstand high
temperatures due to high softening point, but has low density around
0.9202g/cm³ and superior processability (Murray and Gibson, 1971).
Likewise, polypropylene is lighter, stronger and more rigid than
polyethylene.

3. Polystyrene or styrophore. Polystyrene are penetrable to water vapor, oxygen
and carbon dioxide and has low water absorption around 0.04 % to
0.05%.
Normally, polystyrene has density of 1.0g/cm³ to 1.1g/cm. Chemically
it is resistant to weak acids like pH 6.0 to pH 6.5, bases, and vegetables
oils.
Locally, polystyrene boxes are popular for transporting of fish from the
wharf to the market or processing plant. But they are difficult to clean
because of the trapped container water in the ridges and are not durable
especially if pores are damaged.
However, modified polystyrene fish containers using moulded plastic
around showed 10-15% better insulating properties than the ordinary
polystyrene box (Villadsen, Milla and Flores, 1986).
Vacuum Packaging
Vacuum Packaging may be defined as taking off oxygen from the container during
sealing in order to preserve the products.
Packaging materials like polyamide/polythene laminates are suitable for vacuum
packaging for they are resistant to pinhole formation (Hermes, 1998).
The advantages of vacuum-packed products are as follows:
1. Vacuum-packed products have longer shelf-life than ordinary packed products
due to non-occurrence of oxidation.
2. They have better keeping quality especially on dried fish wherein no rancidity
occurs.
3. They demand high price in the market.
The disadvantages of vacuum-packed products are the following:
1. Vacuum-packed products are not applicable to fish roe and mussel meat.
2. The label of the vacuum-packed products are not readable due to deformity of
the surface of the pack.
3. Vacuum-packed products should be refrigerated below 3°C or 37.4°F to prevent
production of toxin by clostridium botulinum.
Vacuum Skin Packaging.
Vacuum skin packaging is an extension vacuum packaging which can be applied to
both film-to-film and film-to-tray sealing (Hermes, 1998). The wrapper is heated and draped
over the product. hence, giving extra “skin”.
The steps in preparing vacuum skin packing are as follows (Hermes 1998).

Directions:
Choose and encircle the letter of the correct answer.
1. This packaging material is resistant to high temperature but has poor quality in low
temperature and becomes brittle.
A. polyvinylchloride C. polystyrene
B. expanded polystyrene D. polypropylene
3. This packaging containers are popular for transporting fish from the wharf to the
processing plant but difficult to clean due to the trapped water in the ridges.
A. polyethylene C. polypropylene
B. polystyrene D. polyamide
4. This container is effective for chilling fish because it can resist extreme heat and can
retain coldness inside.
5. Which of the following is considered an optional label requirement?
A. 250 grams C. fat
B. October 2009 D. Ligo
6. This packaging material is used for the lamination of frozen products.
A. polyamide C. ethylene-vinyl acetate
B. polyvinyl chloride D. polyester
7. Which of the following is required in preparing label?
A. fish illustration C. “555”
B. tomato growing D. 155 grams
Self-Check 2.1

A. product of USA C. lucky 7
B. fish drawing D. purefoods
9. This packaging material is hard and glossy but grease resistant and brittle at all
temperatures.
A. polyamide C. polyvinylidine chloride
B. ethylene-vinyl chloride D. polyvinyl chloride
10. Which of the following is an optional label requirement?
A. nutrition facts C. vignette
B. ingredients D. expiry date

Make a Label for Canned Fishery Product
Procedure:
1. Prepare the necessary tools and materials for making a label.
2. Cut the paper according to the size of the container (tin can).
3. Draw an illustration about the product that attracts the buyer or consumer.
4. Write or print the necessary parts of a label like:
 Name of the product
 Name of manufacturer
 List of ingredients in descending order
 Net weight of the product
 Country of manufacturer
 Expiry date marking
 Nutrition facts
 Brand name
5. Attach the label on the tin can.
Activity Sheet 2.1

Activity Sheet
Make a Label for Canned Fishery Product
1. use necessary and proper materials in making a label?
2. demonstrate the proper technique in making a label?
3. perform task independently?

Good luck!
LO1
 CBLM (Fish Processing II)
LO 2
 CBLM – Fish Processing IV, pp. 4 – 8
REFERENCES

APPLY FOOD SAFETY AND SANITATION
LESSON 4
LO 1. observe personal hygiene and good grooming;
LO 2. implement food safety practices;
LO 3. conduct work in accordance with environment
policies and procedures; and
LO 4. participate in improving environmental practices at
work.
LEARNING OUTCOMES:
do the following:

Brine solution – the mixture of salt and water.
Critical Control Point (CCP) – is a point in time or a physical location at
which failure of control or preventive measures will expose the
consumer to unacceptable health risk.
Debris – remains of something that has been destroyed.
Disasters – the impact of natural or man-made hazards that negatively
affect society or environment.
Epidemiological – describes the origin and development of a particular
disease.
Food borne illness – a kind of illness acquired by eating contaminated
foods.
Food handlers – persons who handle food during food production.
Food hygiene – all conditions and measures necessary to ensure the
safety and suitability of the food preparation and processing.
Food safety – the assurance that food will not cause harm to the
consumer when it is prepared and/or eaten according to its intended
use.
Good grooming – the art of cleaning and maintaining proper and neat
appearance of the body.
Good Manufacturing Practices (GMP) – potable water refers to
drinkable water.
Hazard – a situation which possess a level of threat to life, health,
property or environment.
Hazard analysis – is the identification of selective ingredients, critical
process points and relevant human factors as they affect product
safety.
Hygiene – the science of good health that signifies cleanliness and
freedom from the risk of infectious disease.
Input – something that enters a process from the outside and is acted
upon or integrated.
Definition of Terms

Labeling – the process of putting labels on the immediate container.
Mitigation – a measure that is used to minimize the damaging effect of
an emergency.
Output – is the amount produce/yield.
Oxidation – an action in which oxygen combines with an element or
compound.
Rehabilitation – the process of restoring land after some process
(business, industry, natural disaster, etc.) has damaged it.
Sanitation – is the planned maintenance of the work and product
environment to prevent or minimize hazards of product contamination,
condition and to provide clean, healthful, and safe working conditions.
Standard Operating Procedures (SOP) – the set of practices,
procedures, and rules designed for the promotion and maintenance of
health and cleanliness in the processing plant.
Spill – the release of a liquid petroleum hydrocarbon into the
environment due to human activity.

Directions: Read each statement carefully and choose the letter of the best answer.
1. What illness is acquired by eating contaminated food?
A. air borne illness C. Skin disease
B. food borne illness D. Lung illness
2. Which of the following refers to the science of good health that signifies cleanliness and
freedom from the risk of infectious diseases?
A. hazards C. hygiene
B. sanitation D. cleanliness
3. When do personnel wash their hands wherein personal cleanliness may affect food
safety?
A. at the start of food handling activities
B. immediately after using the toilet
C. after handling raw food or any contaminated material
D. all of the above
Observe personal hygiene and good grooming
LEARNING OUTCOME 1
Pretest LO 1
Let us determine how much you already know about observing personal hygiene
and good grooming. Take this test.
1. Personal hygiene and good grooming is practiced in line with
workplace health and safety requirements.
2. Personal protective equipment is cleaned, checked and sanitized.

4. Which of the following is the concern of personnel hygiene?
A. freedom from any diseases
B. wearing of clean washable garments
C. observing sanitary habits and clean hands
D. all of these
5. Which of the following is not a GMP requirement on personnel hygiene?
A. hazard analysis C. illness and injuries
B. health status D. Personal cleanliness
LO1. OBSERVE PERSONAL HYGIENE AND GOOD GROOMING
GMP Requirements on Personal Hygiene
1. Health Status. People known, or suspected, to be suffering from, or to be a carrier of
a disease should not be allowed to enter any food handling area. It is a likely that
they could contaminate food. Any person so affected should immediately report
illness or symptoms of illness to the management.
Medical examination of a food handler should be carried out, if clinically or
epidemiologically indicated.
2. Illnesses and Injuries. The following conditions should be reported to the
management so that any afflicted persons need to subject themselves to medical
examination and be excluded from handling food.

a. Diseases of the respiratory tract, such as common cold, sore throat,
pneumonia, scarlet fever, tuberculosis, and trench mouth.
Respiratory tract infections spread microorganisms such as staphylococci,
which are indigenous to portions of the respiratory tract.
b. Intestinal disorders, such as dysentery, typhoid fever and infectious hepatitis.
People suffering from intestinal disorders usually shed a lot of intestinal
bacteria such as Shigella, Salmonella, etc. which may be transmitted to food
by dirty hands. A person suffering from salmonellosis for example, may shed
as many as 10 cells per gram of feces, during illness (ICMSF,1988).
c. Skin disorders, such as sores, abrasions, and lesions, infected ears, boil,
scabies and severe rashes. The usual sites for harboring staphylococci are
cuts, burns, abrasion, and pustular lesions. When infected persons handle
food, the hazard of passing staphylococci from skin surfaces to food
increases.
Pre employment physical examination is usually required for every person
intending to work in a food plant in order to establish freedom from above
diseases.
3. Personal Cleanliness.
Food handlers should maintain a high degree of personal cleanliness. They should
wear suitable protective clothing, head covering, gloves, facial masks, and footwear.
Suitable waterproof dressing should cover cuts and wounds, wherein personnel are
permitted to continue working.

Processor’s Outfit as Part of Personal Hygiene
Apron Hairnet
Hand Towels Gloves
Hand Washing
Personnel should always wash their hands when personal cleanliness may affect
food safety, as shown in the following practices:
a. At the start of food handling activities.
b. Immediately after using the toilet
c. After handling raw food or any contaminated material, where this could result
in the contamination of other food items. They should avoid handling ready-
to- eat food when unsure of cleanliness in the process of preparing it.
Personal Behavior or Habits
People engaged in food handling activities should refrain from behavior that
could result in food contamination, such as the following:
d. Smoking
e. Spitting
f. Chewing or eating
g. Sneezing or coughing over unprotected food

Personal effects such as jewelry, pins or other items should not be worn or
brought into food handling areas if they pose a threat to the safety and suitability of
food.
Visitors
Visitors in food manufacturing, processing or handling areas should, where
appropriate, wear protective clothing and adhere to the other personal hygiene
provisions.
Entrance and Exit in a Workplace
1. All entrances and exits must be provided with screened doors swinging outward.
2. Signs of entrance and exit must be posted in corresponding areas.
3. Some organizations require thorough washing of hand and foot bath before entry into
a work area.
4. Wear appropriate work outfit before entry. Deposit them at designated areas upon
exit from the place.

Directions:
Write TRUE if the statement is correct and FALSE if the statement is wrong.
__________ 1. Food handlers should maintain a high degree of personal cleanliness.
__________ 2. People suffering from or a carrier of a disease should not be allowed to enter
any food handling area.
__________ 3. Washing of hands should be done after preparation of food.
__________ 4. Workers should be well-groomed, that is to say, make up is a must for girls.
__________ 5. Smoking or spitting anywhere is allowed during food preparation.
__________ 6. A mask should be worn to cover the mouth during food preparation.
__________ 7. An apron or a laboratory gown that is fitted, cleaned, and pressed must be
worn.
__________ 8. Medical examination of a food handler should be carried out if clinically or
epidemiologically indicated.
__________ 9. Hands should be washed only after using the toilet.
__________ 10. It is advisable to work or prepare foods even with infected wounds or cuts.
Self-Check 1.1

Hand Washing Techniques as a Means of Practicing
Equipment, Tools and Materials:
 water
 soap
 faucet
 drier
 brush
 towels
 tissue paper
 sanitizer
 alcohol (70% ethanol)
Procedure:
Follow the steps below.
Precautions:
1. Use potable water.
2. Check facilities if functioning properly.
3. Take proper care in using the facilities.
Operation Sheet 1.1

Operation Sheet 1.1
((HHaanndd WWaasshhiinngg TTeecchhnniiqquueess AAss AA MMeeaannss OOff
PPrraaccttiicciinngg HHyyggiieennee AAnndd GGoooodd GGrroooommiinngg))
1. prepare the facilities as well as the materials and check
before using (washing)
2. demonstrate the proper washing techniques?

Implement food safety practices
LEARNING OUTCOME 2
1. Sanitary practices in food safety are implemented in line with workplace
safety regulations.
2. Cleanliness and sanitation should be strictly observed.
3. Safety measures are applied according to workplace rules and regulations.
4. First aid procedures are applied and coordinated with concerned
personnel according to workplace standard operating procedures.

Directions: Encircle the letter of the correct answer.
1. How will you ensure the safety of raw materials particularly the quality of fish in
processing especially during handling?
A. by checking the source of supplies
B. by checking on the quality of the fish
C. by monitoring regularly the preparation of fish
D. all of these
2. What is the purpose of applying strict quality control in choosing raw materials for
processing?
A. to prevent inferior finished products
B. to produce good finished product
C. to produce sound marketable product
D. all of the choices
3. How will you ensure that the workers can handle food safely during production?
A. workers are not infected with contagious disease
B. workers are not wearing their Personal Protective Equipment
C. Workers are smoking during preparation/processing of food.
D. worker’s hands are not thoroughly washed.
4. In keeping equipment and facilities safe and sanitary, what must be considered?
A. processing facilities must be well-ventilated
B. processing facilities should be adequately lighted and properly maintained
C. processing equipment/facilities should be cleaned and disinfected before and
after using
D. all of the choices
Pretest LO 2
Let us determine how much you already know about implementing food safety
practices. Take this test.

5. Which among the choices includes practices and procedures implemented in processing
plants to ensure product safety, product quality and prevention of economic fraud?
A. GMP C. HACCP
B. SSOP D. none of the choices
6. GMP covers 3 accepted standards in the maintenance and safety of the following except
one. Which is not included?
A. production and process control
B. worker’s hygiene ad safety
C. housekeeping activity
D. good working conditions of equipment and facilities
7. What is the best standard operating procedure in maintaining the safety of equipment
and facilities?
A. thorough washing
B. subsequent disinfection before and after using
C. both a and b
D. none of the choices
8. For the product to be safe, it must be properly labeled. The following information shall be
declared in every label except one. Which one is not?
A. name of product
B. name and address of the product
C. net weight
D. name of the consumer

LO2. IMPLEMENT FOOD SAFETY PRACTICES
Sanitation in a processing plant is a primary concern of all food processing firms. It is
necessary to prevent or minimize hazards of product contamination and conditions
aesthetically offensive to the consumers, and to provide clean, healthful, and safe working
conditions.
Sanitation standard operating procedures (SSOP) are components of Good
Manufacturing Practices (GMPs) emphasizing sanitation procedures on the topics to be
discussed as follows:
Workplace Sanitation Regulation in Implementing Sanitary Food Handling Practices in
the Following Aspects;
In handling raw materials and supplies
 Check the source of supplies ( fish, salt, packaging materials)
 Check on the quality
- condition of fish( freshness and temperature
- presence of foreign materials
- color and purity of salt
- purity of other additives
In monitoring during production
 The preparation of fish must be monitored regularly to ensure complete removal of
entrails and gills for eviscerated fish and by thorough washing for whole fish.
 The correct brine concentration, amount of other ingredients and the time of soaking
must be strictly observed to ensure uniformity of every batch.
 The proper drying or cooking endpoint must be observed to ensure uniformity of
product quality.

 In packaging for retail packs, proper packing of products in polyethylene(PE) or
polypropylene(PP) bags must be checked.
For bulk packs, check if product is properly stacked in carton boxes or wooden (palochina)
boxes that are lined with high density polyethylene plastic film.
 In labeling, check if it carries appropriate labeling in accordance with the rules and
regulations on labeling of pre-packaged foods. The following information shall be
declared in every container whether in bulk or in retail package.
For locally produced products:
1. The name of the product and product identification (generic name), printed in
bold capital letters.
2. Name and address of the manufacturer
3. Net weight (in metric units)
4. Ingredients (itemized in decreasing order)
5. Chemical additives e.g. preservatives
6. Open date marking e.g. “Best before” or “Consume before Date”
7. Lot Identification Code (Repackers must use manufacturer’s lot I.D. code)
8. Storage instruction: Store in a cool dry place.
For locally manufactured/repacked and imported/repacked products:
1. Same as in numbers 1, 3 to 8.
2. Name and address of manufacturer/repacker/importer

3. Country of origin
In Storing and Transporting
1. Check if properly identified and if new production batches are segregated from
previous batches
2. Check if during storage and transport, product is not exposed to any of the
following
 direct sunlight or near source of strong sunlight
 high temperature and humidity
 contamination with moisture
 contamination with dust or filth from the environment
In Record keeping /Reporting
1. Check production record; daily control chart, weekly summaries of activities, and
corrective actions maintained for a period of at least 12 months from the date of
manufacture. Manufacturers shall provide traders with a Certificate of Quality of
the specified batch or lot sold to the repackers or traders.
2. Check quality control record.
3. Check marketing and distribution record.
Safety Measures to Be Observed in Implementing Sanitary Food Handling Practices
Good Manufacturing Practices (GMP) is a broad term and includes accepted standards in
the safety and maintenance of the following.
 Production And Process Control Safety
1. All operations involving receiving, inspecting, preparing, processing,
packaging and storing of food must be conducted under such conditions that
they do not contribute contamination in the form of filth, harmful chemicals,
undesirable microorganisms or any other objectionable material to the
finished product.
2. A strict quality control of raw materials should be enforced. Low grade raw
materials or those that fail to meet specifications should be rejected because
this would only result in an inferior finished product.
3. Containers and carrier of raw materials, packaging materials, storage and
transportation of finished products should be thoroughly inspected and
monitored.

 Worker’s Hygiene and Safety
1. Good working conditions ensure not only the safety of workers but also safety
of food products that reach the consumers. Food processing plant personnel
must be adequately trained on the proper hygiene and accident prevention
that must be observed or practiced in the plant to assure continuous flow of
work. These minimize the chance of contamination and accidents that cause
unwanted delays.
2. Workers infected with contagious diseases should not be allowed to work as
they can be sources of contamination. They should be quarantined until cured
and safe from spreading the disease. Food handlers with open and infected
wounds or sores in the hands or arms should not be allowed to handle food
products directly for they can contaminate the food they touch. They should
always be made aware of the dangers of haphazard or careless practices.
Strict compliance to sanitary measures should be observed.
 Safety measures to be observed by food handlers:
1. The hands should be washed thoroughly with soap and water. A disinfecting
solution of chlorinated water should be available for rinsing the hands before
handling food. Wearing rings, bracelets, and wrist watches during processing
should be avoided as these can be sources of contamination.
2. Smoking in the preparation, processing, and packing area should never be
allowed. Smoke can be absorbed in the food or the ashes and cigarette butts
may get into the food. Spitting and blowing of nose should never be done
within the premises of the plant. These unhealthy habits contribute to
contamination and spread of diseases.
3. Food handlers should be properly dressed. The use of gowns, aprons, head
caps or hair nets, masks, rubber gloves and boots is ideal. This prevents
contamination of the food by foreign matters from the handler’s body like hair,
dust, and germs exhaled from the nose and mouth. However, for small scale
industries, clean and light colored shirts and caps or hairnets would be
sufficient.
4. Whenever possible, food must not be handled by bare hands during
preparation and packing.
5. Packaging materials must never be handled directly particularly on the side
that shall be in direct contact with the food.

 Equipment and Facilities Safety
1. Processing facilities should be well ventilated, adequately lighted and properly
maintained. Thorough washing and subsequent disinfecting of processing
equipment before and after use should be a standard operating procedure
(SOP).
A good processing plant should have an effective pest control to keep it free
from rodents and insect pests. Cleanliness of processing equipment, utensils
and surroundings prevents both infestation and contamination.
2. Potable water supply should be available from adequate sources. Good
drainage
and sewage disposal system should also be provided. These are essential
for the efficient maintenance of sanitation.
3. Waste disposal should be properly managed to prevent pollution of
surroundings.

Directions: Fill in each blank with a word or words to make the statement complete.
1. __________are components of GMP emphasizing sanitation procedures designed for the
promotion and maintenance of health and cleanliness in a processing plant.
2. __________ is the process of putting/attaching labels on the immediate container.
3. __________ is a primary concern of all food processing firms to prevent or minimize
hazards of product contamination and conditions aesthetically offensive to the consumers.
4. __________refers to the practices and procedures implemented in processing plants to
ensure product safety, product quality and prevention of economic fraud.
5. ____________ is any printed pictorial or material attached to any container.
6. __________ are situations that ensure safety of workers as well as food products that
reach the consumers.
7. __________is a disinfecting solution available for rinsing hands before handling food.
8. __________are protective coverings worn by food handlers to prevent contamination of
the food from foreign materials.
9. __________ refers to clean water that is safe for drinking and cleaning.
10. __________ is a mixture of salt and water.
Self-Check 2.1

1. Food safety hazards must have and implemented HACCP plan.
2. Monitoring procedures are strictly followed.
3. Record keeping systems to document monitoring and corrective actions
are developed.
Conduct work in accordance with environment policies and
procedures
LEARNING OUTCOME 3

Directions: Choose the letter of the correct answer.
1. Which of the following is the legal basis of waste management?
A. R.A.9003
B. R.A 9155
C. R.A. 9503
D. R.A. 8550
2. Which method of treating liquid waste control is employed as a preliminary treatment
for the removal of large solid particles prior to final treatment or discharge into a
municipal sewage system?
A. Screening
B. Lagooning- biological disposal
C. Spray – irrigation – land disposal
D. Chemical treatment
3. Biological action, sedimentation, soil absorption, evaporation, and dilution are the
principles of:
A. Screening
B. Lagooning- biological disposal
C. Spray – irrigation – land disposal
D. Chemical treatment
4. Which of these types of lagoon is used in disposing industrial wastes which meets
the requirements of industries discharging small daily volume of wastes on a
seasonal operation?
A. Impounding lagoon
B. Flow – through lagoon
C. Aerated lagoon
D. Anaerobic lagoon
5. Which of these is not included in housekeeping system?
A. Waste minimization such as reduce, reuse, recycle
B. Energy conservation
C. Productivity improvement schemes
D. Control of pest
6. Hazard Analysis Critical Control Point (HACCP) involves the following prerequisite
programs except:
A. Good Manufacturing Practices
B. Sanitation Standard Operating Procedures
Pretest LO 3
Let us determine how much you already know about conducting work in
accordance with environment policies and procedures. Take this test.

C. Good Housekeeping Systems
D. Quality assurance and inspection
7. HACCP means
A. Hazard Applicable Control Critical Point
B. Hazard Analysis Critical Control Point
C. Hazard Approach Critical Control Point
D. Hazard Acceptable Critical Control Point
8. Which of the following does not belong to the group of HACCP concepts?
A. sanitation control of the potential hazards
B. a preventive system of control particularly on biological hazards
C. a system approach for estimating the risk in producing a food product.
D. universally recognized system as the most effective way to prevent food
borne illness.
9. Which of the following does not belong to HACCP methodology?
A. HACCP Concepts
B. HACCP prerequisite program
C. HACCP principles
D. HACCP preliminary steps
10. Which of these does not belong to HACCP characteristics?
A. The manufacturing process does not contain a control processing step that
effectively destroy harmful bacteria.
B. No terminal heat process is done after packaging.
C. The product is not subject to contamination after processing and before
packaging.
D. The product contain sensitive ingredients which can be assumed as potential
sources of contamination under normal circumstances.
LO3. CONDUCT WORK IN ACCORDANCE WITH ENVIRONMENTAL POLICIES AND
PROCEDURES
The maintenance of cleanliness in a working area requires frequent or continuous
cleaning as well as a clean up at the end of each day. The purpose of this is to keep waste
from accumulating during the operating day. It involves careful organization, training work
scheduling, and the best available equipment, method, and materials.

Hazard Analysis Critical Control Point (HACCP)
HACCP allows processors/regulator to look at what happens during the process to
ensure safety.
Major Concepts of HACCP
1. A preventive system of control particularly on biological hazards
2. A system approach for estimating the risk in producing a food product
3. Universally recognized system as the most effective way to prevent food borne
illness
4. Science - based systematic, identified specific hazards and measures for their control
to ensure food safety
5. Capable of accommodating change, such as advances in equipment design,
processing procedures, or technological developments that can be applied
throughout the food chain from the primary producer to the final consumer
6. Applicable to establishments that produce, process, treat, pack, trade, transport,
serve, or involve in food production
Seven (7) HACCP Principles
1. Hazard analysis
2. Identify critical control points
3. Establish Control limits
4. Monitor critical limits
5. Establish corrective actions in case of deviation from established critical limits
6. Establish verification procedure to ensure that the system is consistent
7. Establish record keeping procedures
General Hazards Characteristics
1. The product contains sensitive ingredients, which can be assumed as potential
sources of contamination under normal circumstances.
2. The manufacturing process does not contain controlled processing steps that
effectively destroy harmful bacteria.
3. There is substantial potential for microbiological abuse in distribution or in consumer
handling that could render the product harmful when consumed.
4. Product is subject to contamination after processing and before packaging.
5. No terminal heat process after packaging.
Hazard Categories
Category Descriptions
I A special category of non-sterile products designed and intended
for consumption by infants, aged, and the sick
II Food products subject to first 3 general hazard characteristics
III Food products subject to 2 of any general hazard characteristics

IV Food products subject to 1 general hazard characteristics
V Food products subject to none of the general hazard
characteristics
Critical Control Points (CCP) for Fresh or Frozen Fishery Products
Input Materials Hazard CCP
a. Fish, Mollusk,
Crustaceans
Decomposition
Unwholesomeness
Prior to Processing
b. Others Not food grade
Ingredients
Unclean
Adulterated
Misapplication
Prior to use
Unsuitable
c. Packaging Materials Not approved for food
contact, unclean, unsound
Prior to use
Packaging area
d. Labels Information not consistent
with regular requirement
Prior to use
e. Cleaning Not approved for agents,
sanitizers, lubricant
surfaces
Misapplication
Prior to use
Use in food plants or on
food on contact
Application area
Production condition
a. Operation and
Sanitation
Non - compliance with
regulation
Prior to or during
processing
b. Process control Non - compliance with
regulation
During processing
c. Storage Non - compliance with
regulation
During storage

HACCP Pre-Requisite Programs
1. Good Manufacturing Practices (GMP)
This provides the sanitary infrastructure for Food Safety that the:
a. Plant grounds and building facilities emphasize pest control;
b. Equipment design provides ease in cleaning and maintenance;
c. Personal hygiene practices and facilities are set;
d. Process controls are followed;
e. Storage and warehousing are free from contamination.
2. Sanitation Standard Operating Procedures (SSOP)
SSOP are components of GMP that emphasize sanitation procedure. They include:
a. Safety of water that gets in contact with food and food surfaces;
b. Condition and cleanliness of food contact surfaces;
c. Measures to prevent contamination;
d. Employee hygiene practices;
e. Control of employee health conditions that could result in contamination of
food and food surfaces;
f. Protection of food and food contact surfaces from adulteration with toxic and
other harmful components;
g. Proper labeling and storage and use of toxic; and
h. Control of pests.
3. Good Housekeeping System
a. Waste minimization such as reduce, reuse, recycle
b. Energy conservation
c. Productivity improvement schemes
Food Processing Plant Facilities and Environment
1. Building
a. Walls. There should be no double walls that could harbor rodents and insects.
b. Screens. The openings such as windows and doors should be properly
screened to prevent insects and birds from entering into the laboratory rooms.
c. Ceilings, walls and floors. These should be smooth and washable, with a
minimum of ledges, beams, and areas where dust and debris could
accumulate. Floors should be in good repair, well drained, and easily cleaned.
d. Ventilation. There must be enough ventilation to prevent condensation.
Condensate forming on overhead pipes and beams may drip into products
and containers and deteriorate structures.
e. Paint. It should stand up under the conditions of use expected because
flaking and peeling of paint on walls and ceiling above food handling areas is
a source of contamination.
2. Plant Lighting
a. Light should be even and without glare, strong reflections or deep shadows,
and of proper color rendition.
b. Light bulbs and tubes should be of the safe type to prevent contamination by
broken glass and to protect workers

3. Water Supply.
a. Private wells and surface supplies must be protected against surface and
underground contamination.
b. There must be regular bacteriological and periodic chemical examinations
made.
c. Well casings must be sealed.
d. Cross-examination of potable and non-potable water distribution should be
examined.
4. Drainage
a. Gutters should be accessible for cleaning.
b. Water flow should be adequate to remove wastes and round bottoms are
easier to clean
c. Floor should be smooth and sloped between 1/8 to 3/8 inch per foot to
prevent standing waste and water.
d. Water should not run across floors where employees walk.
5. Disposal of Solid wastes
a. Solid wastes must be removed from the premises at frequent intervals to
prevent safety hazards, to avoid odors of fermentation and decay and to
prevent insect attraction.
b. Water containers must be properly cleaned, and containers that absorb juices
should not be used.
c. Final disposal must be an area or manner to prevent nuisance and insect
breeding.
6. Drinking Fountain
a. There must be one drinking fountain for every 50 employees.
b. The water temperature must range from 45- 50F is desirable.
c. It should be conveniently located but not within toilet rooms or over hand
washing sinks.
7. Toilets
a. Water flushed toilet is preferable and should be set free from all enclosing
wood.
b. The number of toilets depends on the number of employees.
No. of Employees No. of Toilets
1 - 9 1
10 - 20 2
21 - 30 3
31 - 40 4
41 - 50 5
51 - 60 6
61 - 70 7

71 - 100 8
Over 100 1 for every 20
8. Washing Facilities
a. It should be placed near the toilets and in the washing area.
b. Soap, individual towels or paper napkins suitable for drying devices should be
available.
9. Employee Sanitation
a. Employees’ personal hygiene such as proper clothing, head covering, gloves,
and boots should be checked properly.
b. Wearing jewelries and keeping objects in breast pockets should be avoided.
c. Spitting of employees on the floors and walls as well as smoking are strictly
prohibited.
10. Clean up Procedures:
The general information regarding plant clean up for proper evaluation is as
follows:
a. How much time has elapsed since last clean up?
b. Is a separate clean up group used?
c. Do workers do clean up?
d. Is there a clean up supervisor?
e. Are there clean up specifications such as methods, materials, equipment, and
time?
f. What clean up equipment, detergents, and sanitizing agents are used?
g. When, where, and how are clean up procedures are implemented?
Waste Management
1. It is defined as handling of all wastes in the plant including food wastes, scratch
paper, and fallen dry leaves on the ground, trim wedges and many others into useful
products.
2. It is the utilization of wastes by recycling and reusing these wastes into other
valuable products good for the health of the people to arrive at zero waste.
Legal Basis of Waste Management
Republic Act no. 9003 known as the National Solid Waste Management Act is issued
as part of War on Waste (WOW). To fight against waste provides that all wastes matter will
be recycled and reused into useful items.
Different Ways of Waste Disposal
A. For Liquid Wastes Control
1. Screening. It is employed as a preliminary treatment for removal of large particle of
solid prior to final treatment to be discharged into a municipal sewage system.
2. Lagooning – Biological Disposal. It consist of holding the wastes effluent in open
earthen pits which accomplish treatment under five principles namely:

a. Biological Action (aerobic and anaerobic)
b. Sedimentation
c. Soil absorption
d. Evaporation
e. Dilution
Two basic types of Lagoons used in disposing industrial wastes:
1. Impounding Lagoon. This meets the requirements of industries discharging small
daily volumes of wastes or a seasonal operation, i.e., the canning industry. In this
system, the volumetric capacity is equal to the total waste flow, less loss due to
evaporation and percolation.
2. Flow-through Lagoon. It requires less land and relies on biological action.
3. Spray irrigation – land disposal. This serves as an economic and unobjectionable
waste disposal method when land is available. It is limited only by the capacity of
spray field to absorb the wastewater. The factors required to set up a spray irrigation
are as follows:
a. Quantity of effluent for disposal (per hour, per day, per week, per
season)
b. Land available for disposal area such as the texture of soil profile,
area and dimensions, topography, depth of ground water, location
with respect to plant, and infiltration capacity
c. Character effluent
d. Climate during operational season.
4. Chemical Treatment. Chemical precipitation is a form of partial treatment with the use
of chemical coagulants of lime followed by ferrous sulfate or alum. It removes 25% to
50% of the biochemical oxygen demand. Analytical measurements such as
biochemical oxygen demand (BOD), chemical Oxygen demand (COD) and solid
determination are valuable as control measurements.
BFAR Regulations on Fishery Processed Products
Fish Inspection and Quality Control Section
Regulation and Requirements
I. BFAR Guidelines on plant accreditation/approval:
The accreditation process commences with the application through submission of
LTO, GMP, SSOP and HACCP plan specific to the product, processing activity and
plant location
Accreditation is based on verified compliance with the submitted programs and
established rules and regulations on product safety and quality.
BFAR conducts both announced and unannounced inspections

BFAR provides a certificate of accreditation and a certificate of HACCP
implementation to plants that have satisfactorily met the requirements
Validity of accreditation varies from 6 months ( plant rating of AB or BA) to 1 year (
plant rating of AA)
BFAR notifies plants of any non-compliance deficiencies after each inspection
Accreditation is given only to plants obtaining a plant rating of AB / BA or AA on I.
plant structure and equipment requirements and II. GMP/SSOP and HACCP
implementation
BFAR shall withdraw the accreditation for plants with critical deficiencies.
Delisted plants may apply for re-accreditation after corrective actions have been
effectively instituted on deficiencies that have caused the withdrawal of
accreditation.
The Provisions of the Regulations the Seafood HACCP Regulations
1. Coverage:
a. all "processors"
All seafood-related entities in our establishment inventory. All foreign processors
that export to the U.S.
Exempt:
Fishing vessels
Common carriers
Retail
b. All importers
2. Hazard analysis (HACCP Principle #1)
a. Every "processor" must conduct a hazard analysis to determine whether they have
likely food safety hazards that they must control.
If no:
they do not need a HACCP Plan for the time being (assuming they're right). they
must reassess, however, whenever a significant change occurs.

If yes:
they must have and implement a HACCP Plan.
3. The HACCP plan
a.
Where hazard analysis reveals need, every "processor" must have a written HACCP
plan that's specified to location and kind of product.
b. HACCP plan must ID:
i. Food safety hazards that is reasonably likely to occur.
These include anything that causes food to be unsafe under the act. (Ex. toxins,
micro, chemicals, pesticides, drug residues, physical hazards, decomposition
ii.
Critical control points to control hazards that can occur both inside & outside the
processing plant. (HACCP PRINCIPLE #2)
iii.
Critical limits (i.e., safe operating parameters) for the CCP's. (HACCP
PRINCIPLE #3)
iv. Monitoring procedures (HACCP PRINCIPLE #4)
v. Corrective action plans, if any. (HACCP PRINCIPLE #5)
vi. Verification procedures to: (HACCP PRINCIPLE #6)
vii.
Recordkeeping system to document monitoring, corrective actions, certain
verification procedures. (HACCP PRINCIPLE #7)
c. Signing/dating: Plan must be signed/dated by a senior firm official. This must occur
initially, upon modification, and at least annually.
4. Corrective Actions
Processors may either...
a. Follow corrective action plans they have developed in advance, or
b. Do the following:
Segregate and hold product while determining acceptability of product for
distribution. (Must use person with adequate training or experience)
Take necessary corrective action;

Check the plan to see if it needs to be modified; modify as necessary (Must use
trained individual).
5. Verification
a.
Verifying the HACCP plan: Processors must reassess adequacy of their HACCP
plan at least annually or whenever a significant change occurs.
b. Verifying ongoing activities:
i. Processors must follow written verification procedures that are in their HACCP
plans for reviewing consumer complaints, calibrating their monitoring devices,
engaging in any end-product testing.
ii. Processors must review monitoring and corrective action records within one
week of the creation of the records, and must review calibration & end-product
testing records within a reasonable time.
iii. Processors must check whether their consumer complaints that alleged safety
problems reveal any problems with their HACCP systems that must be fixed.
6. Records
a. Monitoring and similar records must state the name and location of the processor,
date and time, signature/initials of person making the record.
b. Records retention: processors must store records for 1 to 2 years, depending on
type of record and type of product (i.e., shelf-life)
c. Plans, HACCP records, and sanitation records, must be available to FDA inspectors
fro review and copying. Consumer complaints are not available, but the consumer
complaint SOP is available
d. All plans and records in possession of FDA are deemed to be not available for public
disclosure per FOIA regulations. Exceptions: (1) previously disclosed or abandoned
materials; (2) discretionary disclosure in accordance with FDA's FOIA regulations.
7. Training
a. For each processor, certain enumerated HACCP functions must be performed by an
individual who has been trained in HACCP through course materials or who, through
job experience, has provided knowledge equivalent to a course. The course must be
at least equivalent to a standard curriculum recognized as adequate by FDA.
b. The enumerated functions are:
Developing the HACCP plan or adopting a generic-type HACCP plan to fit the
specific needs of a processor.

Reassessing/modifying the HACCP plan as a result of verification activities and
any corrective actions that occur.
Reviewing HACCP records for adequacy.
c.
Processors have a choice: they may either obtain training for one or more of their
own employees, or they may hire trained independent contractors to perform these
functions.
8. Sanitation
a. Monitoring and recordkeeping. Processors must monitor and keep records in eight
(8) enumerated areas of sanitation. Processors may establish their own monitoring
frequencies. This monitoring and recordkeeping may be part of the processor's
HACCP system or in a parallel system outside of the HACCP plan. FDA has access
to these records. The regulations recommend that processors have a sanitation
SOP for the 8 enumerated areas, but it is not required.
9. Special Requirements for Imports
a.
Importers must verify that their overseas suppliers follow HACCP. there are two
ways to verify:
i.
Obtain product from a country with which the U.S. has a HACCP-based
agreement on the equivalency of inspection programs. or
ii. Implement verification procedures:
product specifications for safety and
affirmative steps to ensure that HACCP is actually practiced. Any of the
following:
1. obtaining processor's HACCP records;
2.
obtaining either continuing or lot-by-lot certificate from foreign government
inspection authority or competent third party certifying product processed
according to requirements;
3.
going overseas and inspecting facilities to ensure processing of product
according to requirements;
4.
obtaining and keeping on file an English copy of processor's HACCP plan
and a written guarantee that it is being followed;
5.
End-product testing and keeping on file an English copy of guarantee that
plan is being followed.

10. Special Requirements for Mollusk Shellfish
a. Controlling the origin of mollusk shellfish (i.e. properly classified waters) is most
important preventive control for most hazards. Thus, the HACCP plans of
processors of mollusk shellfish must include how this control is being performed,
including how processors are only obtaining shellfish:
From water approved by a "shellfish control authority",
From harvesters who are in compliance with local licensure requirements.
If properly "tagged".
11. Special Requirements for Smoked Fish
a. Botulism is a significant likely hazard for this type of product if not sufficiently
controlled. Thus, the HACCP plans of processors of smoked fish must include how
they are controlling this hazard to ensure zero toxin production in the product for a
time slightly beyond the shelf life of the product.
12. Time Frame for the Implementation
a. The industry has two years to obtain training, write HACCP plans, install HACCP
systems, engage in sanitation monitoring, etc. FDA is preparing to conduct
voluntary, "dry run" HACCP inspections during this two year period. Full, mandatory
implementation must occur by the end of this period.
Write TRUE if the statement is correct and FALSE if the statement is wrong.
________ 1. Hazards analysis is the identification of selective ingredients, critical process
points, and relevant factors as the key to product safety.
________ 2. The manufacturing process does not contain control processing in breast steps
that effectively destroy bacteria.
________ 3. A product can be subjected to contamination after processing and before
packaging.
________ 4. Walls should be doubled to prevent harboring rodents and insects.
________ 5. Wearing of jewelries and keeping objects pockets by employees should be
encouraged.
Self-Check 3.1

________ 6. Spitting of employees on the floors and walls as well as smoking are allowed.
________ 7. Washing facilities should be placed near the toilets and in the washing area.
________ 8. There must be regular bacteriological and periodical chemical examination of
water supply.
________ 9. Chemical precipitation is a form of partial treatment with the use of chemical
coagulants of lime followed by ferrous sulfate or alum.
________ 10. Spray irrigation serves as an expensive and objectionable waste disposal
method when land is available.
Ways of Disposing Liquid Waste
Procedure:
Group students and have them identify and demonstrate the different ways of disposing
liquid waste.
Operation Sheet 3.1

Job Sheet
WWaayyss ooff DDiissppoossiinngg LLiiqquuiidd WWaassttee
1. employ the proper techniques of treating waste before
disposing?
2. demonstrate/perform the proper ways of disposing liquid
waste?

Participate in improving environment practices at work
LEARNING OUTCOME 4
1. Preparedness and mitigation activities.
2. Response activities during a chemical spill.
3. Rehabilitation activity after a chemical spill.

Directions: Choose the letter of the correct answer.
1. Which of the following environmental hazards refers to a sudden rise, usually brief, in the
water level of a stream to a peak from which the water level recedes at a slower rate?
A. fire C. chemical spill
B. flood D. None of these
2. What is referred to as a rapid oxidation with evolution of light and heat?
A. flood C. Fire
B. chemical spill D. All of these
3. What environmental hazard is caused by contamination of food with biological and
chemical contaminants?
A. chemical spill C. Flood
B. fire D. Food poisoning
4. Which of the following hazards usually happens during laboratory work wherein students
come in contact with poisonous/dangerous chemicals?
A. chemical spill C. Food poisoning
B. electrical blackout D. Pollution
5. Which of the following environmental hazards refers to the discoloration of bodies of water
due to the presence of an extremely enormous amount of “bloom” of a group called
dinoflagellates which are toxic?
A. pollution C. Flood
B. fire D. Red tide
6. What should be done as a response during pollution?
A. clean up coastal areas
Pretest LO 4
Let us determine how much you already know about participating in improving
environment practices at work.. Take this test.

B. boil water for consumption
C. provide warning signs or posters in affected areas
D. all of the above
7. What mitigation or preparedness should be made in case of power interruption?
A. Hang the flashlight C. Both A and B
B. Have ready a gas lamp or a candle D. None of these
8. Which of the following response should be done during chemical spills?
A. vacate the room
B. avoid throwing water or touching the chemicals with bare hands
C. inform proper authorities
D. all of these
9. What PD is the fire code of the Philippines containing salient provisions on death and
injury to persons and loss damage to property?
A. PD 9003 C. PD 1185
B. PD 8550 D. PD 9155
10. Which of the following refers to the release of a liquid petroleum hydrocarbon into the
environment due to human activity?
A. spill C. debris
B. flood D. pollution

LO4. PARTICIPATE IN IMPROVING ENVIRONMENTAL PRACTICES AT WORK
The Environmental Hazards
Floods
Flood is defined as a rise, usually brief, in the water level in a stream to a peak from
which the water level recedes at a slower rate.
Safety Precautions Before the Flood
1. Ensure that you understand the dangers of flood properly.
2. Know the flood history of your area.
3. Make a mental note of the nearest high ground to your place.
4. Understand the warning message, the impacts of major, moderate or minor flooding
to your area and which areas are vulnerable to the different degrees of flooding.
5. In times of bad weather, always listen to official warnings issued by local authorities.
6. Prepare a flood emergency kit.
7. Prepare and discuss with other members of the community, the details of a local
hazard map.
8. Indicate the flood path and the sequences of flooding in the area.
9. Evacuation plans should be made in advance. Each member of the family must be
given specific role and responsibility in case of evacuation.
10. If your community has boats, make sure they are well maintained and properly tied
up to a tree or other permanent object. Emergency workers may assist people in
flooded areas. You may be able to help them.
11. Try to avoid walking through the flooded area. Flooding may have caused familiar
places to change since flood waters often erode roads and walkways. Flood debris
may hide animals and broken bottles and sharp steel ends.

12. If you must walk through a flooded area, stay on firm ground. Standing water may be
electrically charged from underground or downed power lines. Check them.
13. Do not touch any damp electrical sockets or turn on the electricity if the house had
been flooded until it has been checked and dried up for some time.
What to Do After the Flood?
1. Inform your neighbors that you are returning home and obtain advice before making
a decision.
2. Roads may still be closed because they have been damaged or are still covered by
water. If you happen to come across such road with stop signs please avoid these
roads and find another way.
3. Keep listening to the radio for news. Additional flooding or flash flood may occur.
Returning to Normal Life After the Flood
Floods can cause emotional and physical stress. You need to look after yourselves
and your family during the transition period. It may take some time to get a house back into
its original condition. There are ways that can help you and your family return to normal life.
1. Before entering the house, get advice from skilled persons about the supply of
electricity, water, gas, and others. Get their advice on the necessary repairs and do
not enter the house if you cannot get any advice.
2. Rest and eat well before starting clean up operations. Make sure that there is no
more threat of the occurrence of flash flood.
FIRE
Fire is frequently referred to as rapid oxidation with the evolution of light and heat. It
is the result of chemical combination of materials (fuel) with oxygen in the presence of
enough heat.
Classes of Fire
Class A. It is a freely burning fire in ordinary combustible materials such as wood, cloth,
paper, and others.

Elements of Fire
and the Fire Triangle
HeatSources
ToReach Ignition Temperature
Open Flames - The Sun
Hot Surfaces
Sparks and Arcs
Friction - Chemical Action
Electrical Energy
Compression of Gases
OxygenSources
Approximately16% Required
Normal air contains 21% O2.
Some fuel materials contain
sufficient oxygen within their
makeup to support burning.
Gas
Natural Gas Propane
Butane Hydrogen
Acetylene
Carbon Monoxide
Others
Liquids
Gasoline Kerosene
Turpentine Alcohol
Liver Oil Paint
Varnish Lacquer
Olive Oil Others
Solid
Bulky - Dust
Finely Divided Coal
Wood Paper
Cloth Plastic
Grain Others
PhysicalState
Class B. It is caused by a flammable liquid such as oils, spirits and petroleum products.
Class C. The fire involves energized electrical equipment
Class D. This is a metal fire (Magnesium, Titanium)
Class E. This is a nuclear fire.
Class K. This is a kitchen fire.
FIRE: An Unpredictable Hazard and Disaster
What is PD 1185?
PD 1185 is the fire code of the Philippines containing these salient provisions;
WHEREAS, death and injury to persons and loss damage to property by fire have reached
alarming proportion that the economic and social gains of the society are being continually
undermined;
WHEREAS, in order to effect a meaningful reduction of the alarming fire losses, there is a
need to develop national consciousness and involvement of all persons in the prevention
and suppression of fires;
WHEREAS, fire prevention and suppression require the adoption of uniform fire safety
standards, the incorporation of fire safety construction and provision of protective and safety
devices in buildings and structures;

Extinguishing this kind of fire is usually misunderstood
when firefighters dose off water on the unburned houses.
Phases of Fire
1. Incipient
2. Free Burning
3. Smoldering
Enclosed Area
1. Incipient
2. Smoke Stage
3. Flame Stage
4. Heat Stage
Open Area
Heat generates thermal energy and may travel in any
direction that will affect clusters of houses.
WHEREAS, there is an urgent need for an agency primarily responsible for the
implementation and coordination of the activities of all sectors of society on fire safety,
prevention and suppression;
WHEREAS, in order to effectively implement all efforts to minimize the occurrences of fires
and their destructive effects, full financial, equipment and personnel support by the
government and the private sector is necessary;

CHEMICAL SPILL (Hazard of Laboratory Work)
One of the hazards of laboratory work is chemical spill.
It becomes hazardous when students come in contact
with poisonous or dangerous chemicals.
Preparedness and Mitigation
1. Take precaution when handling chemicals.
2. Educate students on proper handling of chemicals.
3. Keep safe storage of chemicals.
4. Dispose chemicals properly.
5. Use gloves and mask when handling chemicals.
6. Close drawers of storage cabinet.
7. Maintain a stable environment.
8. Strengthen laboratory capabilities.
9. Provide fire extinguishers.
Response (What to do during chemical spills)
1. Vacate the room.
2. Avoid throwing water or touching the chemicals with bare hands.
3. Inform proper authorities.
4. Cover nose with wet cloth then transfer casualty to a safer place.
5. Give milk and starch for ingested chemical.
6. Ensure adequate air circulation around the victim.
Rehabilitation Phase after Chemical Spill
Call 117 0r local counterparts for paramedic
Electrical Blackout
It is an interruption of normal source of electrical power.
1. Hang the flash light.
2. Prepare ready a gas lamp or a candle.
Response (What to do during electrical blackout?)
1. Unplug all electrical appliances.
2. Stay put in one place to avoid accidents.
Rehabilitation Phase
1. Check electrical outlets and switches.
2. Avoid electric wiring hanging near trees.

Food Poisoning
It is a contamination of food with biological contaminants such as bacteria, fungi,
viruses, and parasites. Chemical contaminants can take the form of agricultural chemicals
(pesticides, insecticides, herbicides, fungicides; environmental pollutants (mercury, lead),
veterinary products (antibiotics, growth enhancers), and additives (food additives, food
coloring).
1. Discourage children’s patronage of processed food.
2. Wash raw food thoroughly.
3. Cook food properly.
4. Eat cooked food immediately.
5. Store cooked food properly.
6. Avoid contact between raw and cooked food.
7. Wash your hands as often as possible.
8. Keep all kitchen surfaces meticulously clean.
9. Protect food from insects, rodents, and other animals.
10. Ensure that the school clinic is operational.
11. Ensure that policies related to canteen operation be strictly enforced.
12. Store dangerous chemicals out of children’s reach.
Response (What to do during food poisoning?)
1. Do not panic.
2. Increase fluid intake to prevent dehydration, but if not tolerated orally, may be
brought to the hospital for intravenous fluid treatment.
3. Induce vomiting.
4. Seek medical assistance in case of complication that may result to hepatitis, typhoid
fever, diarrhea, cholera, dysentery, amoebiasis, etc.
1. Encourage regular vendors selling outside the school to observe proper food
handling and preparation
2. Authorize guards to station outside the school to check and remind street vendors to
cover prepared food.
3. Require the students to bring their own eating utensils such as plates, spoon and
forks, and glasses when they buy street food.
4. Have regular checking by authorized sanitary inspectors of the facilities and food
handlers in the school canteen.

Environmental Hazards
Red Tide
It refers to the discoloration of water
bodies due to the presence of an extremely
enormous amount of “bloom” of a group called
dinoflagellates which are toxic and responsible
for paralytic shellfish poisoning (PSP).
1. Disseminate red tide information, symptoms, and progression.
2. Keep track of media information regarding Red tide.
3. Avoid ingestion of fish, shellfish, mollusks, crabs.
Response (What to do during red tide)
1. Monitor progression of symptoms and seek medical advice.
2. Avoid or refrain from eating seafood.
Seek medical assistance.
Pollution
This is caused by the pollutants
thrown into the ocean like seaweeds,
marine litter, spills, fertilizers, pesticides
from irrigation, and others.
1. Educate people on the proper disposal of waste.
2. Initiate mass cleaning of seashore.
3. Implement marine environmental law.
Response (What to do during pollution)
1. Clean up coastal areas.
2. Boil water for consumption.
3. Provide warning signs or posters in affected areas.
Seek medical assistance for water-borne casualty.

Directions: Write True, if the statement is correct and False, if the statement is wrong.
____________ 1. Washing raw food thoroughly and cooking it properly is one of the
mitigations in case of food poisoning.
____________ 2. Pesticides, insecticide, herbicides, and fungicides are examples of
chemical pollutants which cause food poisoning.
____________ 3. Connection of all electrical and office appliances should be done as a
response during an electrical brown-out.
____________ 4. Milk and starch are examples of chemical spills that are hazardous and
dangerous.
____________ 5. Environmental hazards include flood, chemical spill, fire, pollution, brown-
out, red tide, and food poisoning.
____________ 6. There must be a provision of necessary tools like emergency kit in case of
flood and other emergencies.
____________ 7. Fire is not only hazardous to health but also a threat to economy.
____________ 8. Flood is the result of chemical combination of materials (fuel) with oxygen
in the presence of enough heat.
____________ 9. Keep your emergency kit wet and dangerous.
____________ 10. Just go near river banks or where there are signs of landslide or to areas
where people have vacated.
Self-Check 4.1

Conduct a drill on what to do in case of an accidental chemical spill in a food processing
plant
Procedure:
1. Vacate the room
2. Avoid throwing water or touching the chemicals with bare hands.
3. Inform proper authorities.
4. Cover nose with wet cloth then transfer casualty for safer place.
5. Give milk and starch for ingested chemical
6. Ensure adequate air circulation around the victim
7. Call 117 or local counterpart for paramedic.
Activity Sheet 4.1

Activity Sheet
Conduct A Drill On What To Do In An Accidental Chemical Spill In A Food Processing
Plant
1. wear appropriate protective outfit/gadget in doing
preparedness and mitigation ?
2. prepared tools, materials, equipment and other gadget
in response to chemical spills?
3. demonstrate the proper techniques and safety measures
while working ?

Good luck!
LO1
 CBLM – Fish Processing II, pp. 14, 16 – 19
LO 2
 CBLM – Fish Processing IV, pp. 13 – 16
LO 3
 CBLM (Fish Processing), pp. 28 – 32
LO 4
 CBLM (Fish Processing IV), pp. 4 – 14
REFERENCES

Answer Key
LESSON 1. Use food processing tools, equipment and utensils
Pretest LO1
1. A
2. A
3. B
4. D
5. A
6. A
7. B
8. A
Self-check 1.1
1. Salinometer
2. Refractometer
3. Calibrate
4. Chlorine
5. Cylinder
6. Measuring cup for liquid ingredients
7. Distilled water
8. Thermometer
9. Weighing scale
10. One
11. Knives
12. Scissors
13. Tong
14. Chopping board
15. Earthen pots
LO2. Use tools, equipment and instruments following standard procedures
Pretest LO2
1. d
2. a
3. c
4. c
5. d
Self-check 2.1
1. d
2. d
3. b
4. d
5. a
6. c
7. b
8. d
9. d
10. d
Self-check 2.2
1. Conformity

2. Device
3. Graduation
4. Workplace
5. Brine
6. Catalogue
7. Equipment
8. Instrument
9. Brochure
10. Standard
Self-check 2.3
1. d
2. c
3. b
4. a
5. c
6. c
7. b
8. a
9. b
10. d
LO3. Perform post-operation activities
Pretest LO3
1. d
2. d
3. d
4. d
5. c
Self -check 3.1
1. Check
2. Breakdown
3. Crack
4. Electrocution
5. Inspect
6. Lubricant
7. Preventive Maintenance
8. Repairs
9. Switch
10. Switch – off
LESSON 2. Perform Mathematical Computations
LO1. Gather and tabulate the recorded data relevant to processed food production.
Pre-test LO1
1.b
2.d
Self-check 1.1
1. 4
2. ¾

3.b
4.a
5.b
3. 454
4. ½
5. 32
6. 3
7. 16
8. 1/8
9. 2500
10. 38.94
LO2.Review various formulations
Pretest LO2
1. b
2. a
3. c
4. a
5. b
Self-check 2.1
1. Concentration of a solution
2. Cost
3. Raw food cost
4. Production cost
5. Semi permeable membrane
6. Solution
7. Homogenous
8. 20 % - 60%
9. Brine
10. Dissolution
LO3.Calculate the production input and output.
Pre-test
1.a
2.a
3.a
4.a
5.a
Self-check 3.1
1. Yield
2. 1:1 and 1: ¾
3. 1:4
4. 250 grams
5. 1:3
LO4.Compute the costs of production.
Pre-test LO4
1. c
2. c
3. c
4. c
5. b
Self-check 4.1
1. b
2. e
3. a
4. c
5. d

LESSON 3. Interpret Plans and Drawings
LO1.nterpret lay-out plan.
Pre-test LO4
1. D
2. A
3. A
4. B
5. B
Self-check 4.1
1. Preparation
2. Sterilizing
3. Receiving
4. Labeling
5. Storing
6. Layout
7. Specification
8. Labeling
9. Label
10. Vacuum packaging
LO2. Perform outer packaging procedures.
Pretest LO2
1. D
2. B
3. C
4. A
5. C
Self-check 2.1
1. B
2. D
3. B
4. A
5. D
6. C
7. D
8. A
9. D
10. C
LESSON 4. Apply Hygiene and Sanitation
LO1.Observe personal hygiene and good
grooming
Pretest LO1
1. B
2. C
3. D
4. D
5. A
Self-check 1.1
1. True
2. True
3. False
4. False
5. False
6. True

7. True
8. True
9. False
10. False
LO. 2 Implement food safety practices
Pretest LO2.
1. D
2. D
3. A
4. D
5. A
6. C
7. C
8. D
Self-check 2.1
1. SSOP
2. Labeling
3. Sanitation
4. GMP
5. Label
6. Good working conditions
7. Chlorinated water
8. PPE
9. Potable water
10. Brine solution
LO3. Conduct work in accordance with environmental policies and procedures
Pretest LO3
1. A
2. A
3. B
4. A
5. B
6. D
7. B
8. A
9. A
10. C
Self-check 3.1
1. True
2. True
3. True
4. False
5. False
6. False
7. True
8. True
9. True
10. False
LO4. Participate in improving environmental practices at work.
Pretest LO4
1. B
2. C
Self-check 4.1
1. True
2. True

3. D
4. A
5. D
6. D
7. C
8. D
9. C
10. A
3. False
4. False
5. True
6. True
7. True
8. False
9. False
10. False

Acknowledgement
This Learning Module was developed for the Exploratory Courses in Technology and
Livelihood Education, Grades 7 and 8 of the K to 12 Curriculum with the assistance of the
following persons:
This Learning Module on Food “Fish” Processing NC II was developed by the
following personnel:
MODULE WRITER
FERDINAND S. BRAVO
Principal IV
Binmaley School of Fisheries
Binmaley, Pangasinan Region I
REVIEWERS
GIL P. CASUGA
Chief TESD Specialist
REYNALDO S. DANTES
Senior TESD Specialist
MARIA A. ROQUE
BERNADETTE S. AUDIJE
VICTORIO N. MEDRANO
Principal IV, SPRCNHS
PARALUMAN R. GIRON, Ed.D.
Chair, Sub-TWG on K to 10
BRENDA B. CORPUZ, Ph.D.
TA for K to 12 Curriculum
OFELIA O. FLOJO
Retired Assistant Chief, EED, Region IV-A
BEATRIZ A. ADRIANO
Principal IV, ERVHS
AIDA T. GALURA
VSA II, ACNTS
DOMINGA CAROLINA F. CHAVEZ
Principal II, MBHS
DOCUMENTORS / SECRETARIAT
PRISCILLA E. ONG
K to 12 Secretariat
FREDERICK G. DEL ROSARIO
Head Teacher III, BNAHS
EMMANUEL V. DIONISIO
Head Teacher III, AFGBMTS
LYMWEL P. LOPEZ
Teacher I, AFGBMTS
DANTE D. VERMON JR.
Teacher I, AFGBMTS
CHERLYN F. DE LUNA
Teacher I, AFGBMTS
Dir. IMELDA B. TAGANAS
Executive Director, Qualifications Standards Office
K to 12 Learning Area Team Convenor, TLE/TVE

K to 12 fish processing learning module

More Related Content

What's hot (20)

Similar to K to 12 fish processing learning module (20)

More from Noel Tan (20)

Recently uploaded (20)

K to 12 fish processing learning module