Various and multilevel of wavelet transform for classification misalignment on induction motor with quadratic discriminant analysis

TELKOMNIKA Telecommunication, Computing, Electronics and Control
Vol. 18, No. 2, April 2020, pp. 961~969
ISSN: 1693-6930, accredited First Grade by Kemenristekdikti, Decree No: 21/E/KPT/2018
DOI: 10.12928/TELKOMNIKA.v18i2.14827  961
Journal homepage: http://journal.uad.ac.id/index.php/TELKOMNIKA
Various and multilevel of wavelet transform
for classification misalignment on induction motor
with quadratic discriminant analysis
Pressa Perdana Surya Saputra1
, Misbah2
, Hendra Ariwinarno3
, Farid Dwi Murdianto4
1,2,3
Department of Electrical Engineering, Universitas Muhammadiyah Gresik, Indonesia
4
Electronics Engineering Polytechnic Institute of Surabaya, Indonesia
Article Info ABSTRACT
Article history:
Received Jul 12, 2019
Revised Jan 2, 2020
Accepted Feb 13, 2020
Induction motors have become a major part of the industry because of strong
construction, cheap in purchasing and maintenance, high efficiency, and easy
to operate. Preventive maintenance must always be carried out on all industrial
equipment, including induction motors to last long and prevent further
damage. Based on research in the industry, around 42%-50% or almost 50%
is bearing damage. One reason is the occurrence of misalignment during
the installation of the load on the induction motor. This study tries to identify
the condition of the motor and classify the level of misalignment damage that
occurs. In the process, the mother wavelet like as Daubechis, Symlet and
Coiflet discrete wavelet transform (DWT) are selected as tools in processing
motor vibration data. The level of DWT applied is 1st to 3rd level. Then,
the three types of signal extraction, namely sum, range, and energy, which are
obtained from a high-frequency signal of DWT, are used as input to Quadratic
and Linear Discriminant Analysis. Then, discriminant analysis analyzes and
classifies them into normal operation and two misalignments conditions.
The simulation shows that 1st level of Daubechis DWT combined with
quadratic discriminant analysis generates the best classification. It results 0%
error of classification with Db3, Db4 and Db5, 4.17% error with Db1 and
8.33% error with Db2.
Keywords:
Discriminant analysis
Feature extraction
Misalignment
Mother wavelet
This is an open access article under the CC BY-SA license.
Corresponding Author:
Pressa Perdana Surya Saputra,
Department of Electrical Engineering,
Universitas Muhammadiyah Gresik,
101 Sumatra St., Gresik Kota Baru, Gresik, Jawa Timur, Indonesia.
Email: pressa@umg.ac.id
1. INTRODUCTION
Since it was first discovered, induction motors have become a major part of the industry. That is
because the induction motor has strong construction, is cheap in purchasing and maintenance, high efficiency
at rated speed and torque, and easy to operate [1-3]. The motor is operated in a humid, dirty, hot environment,
etc., which can effect breakdown to parts of the motor. Preventive treatment is needed to prevent defect, extend
motor life, and find early breakdown to the induction motor. Defect of insulation and windings is the most
common type of breakdon. Bearing defects are 42%-50% of all motor breakdown [4-8]. Bearing motors are
valuable between 3%-10% of the actual motor cost. However, the fee due to downtime that occur, so that
the production target is not achieved makes bearing failure become very expensive. In general this is

 ISSN: 1693-6930
TELKOMNIKA Telecommun Comput El Control, Vol. 18, No. 2, April 2020: 961 - 969
962
caused by production errors, lack of lubrication, and installation errors. Motor misalignment is one of
the installation errors.
Misalignment is a condition in which deviations occur at the midpoint between two searching axes.
If the clutch experiences a misalignment, the clutch will be damaged quickly and cause a lot of vibration [9].
The previous method used predictive treatment in detecting motor defect. That is, a manual inspection is carried
out by the operator to inspect the motor. Thus, the motor needs to be turned off so that operator safety is
guaranteed. This of course requires a lot of time and cost. In addition, the quality of checks varies depending
on the operator carrying out the maintenance. Therefore, to overcome the problems above a method was
developed to detect motor damage from the vibration signal characteristics.
One method for detecting fault on induction motor is using the MCSA method. The MCSA monitors
interference by analyzing the stator circulation. MCSA uses the FFT method in analyzing motor current
signals [10, 11]. In addition, the use of motor vibration can also be used to detect fault of induction motor. This
is because motor fault will produce several effects, one of which is the vibration of the induction motor.
A study has been conducted to compare the MCSA method and vibration method [12]. This study shows that
the MCSA's ability and vibration method to detect misalignment produce similar curve patterns. However, this
study has not applied a detection algorithm.
This research classify process of misalignment and level of misalignment in induction using mother
wavelet, including Daubechis, Coiflet and Symlet discrete wavelet transform (DWT) and Discriminant
Analysis. Induction motors that are operated and engineered so that under three condition of operation. And
then, Daubechis, Coiflet and Symlet DWT from level of 1st
to 3rd
is applied to generate vibration signal of
motor in detil signal or high frequency signal. Then, Feature extraction, including range, sum, and energy,
generated from detil signals is collected. Quadratic and linear discriminant analysis (QDA and LDA) verifies
and classifies motor data into three conditions of motor.
2. RESEARCH METHOD
General description of the method to be worked is shown in Figure 1. The vibration signal from
the induction motor will be taken by piezoelectric sensor. And then, it will be stored on the SD Card by
the microcontroller. Furthermore, vibration data consisting of motor vibration data in normal operation,
misalignment of 1 mm and misalignment of 1.5 mm will be processed using Daubechis, Symlet and Coiflet
DWT in level of 1st
to 3rd
. DWT results taken for further processing are high frequency signals. The high
frequency signal is processed to take the range, sum and energy variables to be applied as input for QDA and
LDA. The output of QDA and LDA is motor condition under normal operation, misalignment of 1 mm and
misalignment of 1.5 mm.
Figure 1. Misalignment classification process in induction motor

TELKOMNIKA Telecommun Comput El Control 
Various and multilevel of wavelet trasnform for classification misalignment on… (P. P. S. Saputral)
963
2.1. Experimental setup and study case
Laboratory experimental setup is done to simulate motor condition in normal operation, misalignment
of 1mm and misalignment of 1.5 mm. Experimental scheme is shown in Figures 2 (a) and (b). Induction motor
that has 0.5H P power, with a speed of 1400 RPM, 220 Volt voltage and 50 Hz working frequency paired with
a generator as a mechanical load. In the installation, the generator is installed in a normal alignment condition
or in the direction of the motor, 1 mm shifted and 1.5 mm shifted. And then sensor of piezoelectric is applied
to measure vibration value, then it is saved to storage device by using microcontroller.
(a) (b)
Figure 2. (a) Generator and motor scheme, (b) Collect of motor vibration data condition
2.2. Discrete wavelet transform
Discrete wavelet transform (DWT) is presented in this research because it has simple calculation and
relatively small time interval continuous wavelet transform. Other name of scaling/dilatation parameter is low
pass filter (LPF) or it also can be called as father wavelet. and translation parameter is also called as high pass
filter (HPF) or mother wavelet [13-15]. We will use both of them to do wavelet transform and inverse wavelet
transform. LPF and HPF filter with different cut off frequency is used to transform signal. High frequency
signal or detail signal (cD) is output from HPF and low frequency signal or approximation signal (cA) is output
from LPF [16]. The relationship between LPF/father wavelet and HPF/mother wavelet can be described as in
the following (1-3) :
𝛷𝑗,𝑘 = 2 𝑗/2
Φ(2 𝑗
𝑡 − 𝑘), 𝑗, 𝑘 𝜖 𝑍) (1)
𝛹(𝑡) = 𝛷(2𝑡) − 𝛷(2𝑡 − 1) (2)
with Ψ (t) is the mother wavelet and Φ (2t) is the father wavelet. The function of the equation of the mother
wavelet is (3):
𝜓𝑗,𝑘(𝑡) = 2 𝑗/2
𝜓(2 𝑗
𝑡 − 𝑘), 𝑗, 𝑘 𝜖 𝑍 (3)
based on (1) and (3) the mother wavelet and equation (1). Full equation of DWT is explained as (4).
𝑓(𝑡) = 𝐶0,0 𝜙(𝑡) + ∑ ∑ 𝑑𝑗,𝑘Ψ𝑗,𝑘(𝑡)2 𝑗−1
𝑘=0
𝑀−1
𝑗=0 ) (4)
The data processing process starts by passing vibration signals in HPF and LPF filters. The process
will produce HF signal (cD) and LF signal (cA). Both of them have the amount of data as much as half of
the original data/initial data. This process is named the 1st level decomposition process. Furthermore, LF signal
(cA) will be passed again in HPF and LPF filters and will produce HF signal (cD) and LF signal (cA) at
the next level. This level is called the 2nd level decomposition process. This process will continue to the desired
decomposition level [17, 18].
2.3. Feature extraction
After getting high frequency signal or Detil signal (cD) from DWT, then we will calculate the feature
extraction from the HF signal (cD). The HF signal (cD) processed is level of 1st to 3rd. Then, feature extraction
such as sum, range, and energy, is generated from the Detil/HF signals. Range of signal is the difference
between the maximum and minimum values. This can be described as (5).
Range = Max of signal – min of signal (5)

 ISSN: 1693-6930
964
Then, sum of signal is absolute value of signal and then summed in a certain time span. This can be described
as (6).
Sum =
1
| ( ) |
n k
n
d n
=
=
 (6)
Whereas, the signal energy, e, is the sum of the squares of each signal component. This can be written
as (7) [19-22].
e =
2
1
( ( ))
n k
n
d n
=
=

(7)
Three of these three signal characters will be processed as input in QDA and LDA so that the condition of
the motor can be known and the level of damage can be determined.
2.4. Quadratic discrinant analysis
QDA is a statistical approach to classify an amount of data into some clusters based on some
characteristics. each of data in one of group will not be member in other group [23]. This is alike to multiple
linear regression. The divergence lies in the type of data in the dependent and independent variables.
The multiple regression is utilized in case scale of metric is used in dependent variable and either non-metric
or metric scale is used in independent variable. While, discriminant analysis is utilized in case dependent
variable is categorical and the independent variable utilize a metric scale.
Model of discriminant analysis is an formula that indicates a linear or quadratic composite of some
independent variables, namely:
D = b0 + b1X1 + b2X2 + b3X3 + … … + bkXk (8)
from (8), it can be explained that D is the discriminant value, b is coefficient of discrimination and X is variable
of independent. Value of D is uniue, so that according on the value of D, prediction of member value can
be determined.
In QDA, merger of predictor variables produces zone shaped graph of quadratic function so that it is
expected to produce result more precise and higher accuracy. Nevertheles, an increase in the number of
predictors will make this analysis run into overfits (variability is too large) [24, 25]. Formula of QDA score to
classify data into member of one of groups is in (9) as follows:
( ) ( ) iii
T
ii
Q
i pxxSxxSxd ln
2
1
ln
2
1
)(ˆ 1
+−−−−= − (9)
with d is score value of discriminant, x is data, Si is the covariance matrix and pi is prior probability of
the ith population.
3. RESULTS AND ANALYSIS
The motor is taked action in some period of time in three states, including normal condition, 1mm
misalignment and 1.5 mm misalignment. The output of vibration signal is sended to data storage by vibration
sensor. Then, by using matlab software, vibration data on data storage is processed. The output of vibration
signal of motor is shown in the Figure 3. We can see that motor signals in normal conditions have tenuous and
low value data values. When there is a 1mm of misalignment, the graph gets tighter and sometimes there are
spikes. Furthermore, 1.5 mm of misalignment produces a tight graph and a high value.
3.1. Discrete wavelet transform
The next, vibration signal of induction motor is filtered using Daubechis, Coiflet and Symlet DWT.
The output of DWT that is used in the next process is HF signal (cD) at level of 1st
to 3rd
. Predicted that at high
level, idetification is more accurate. Transformed vibration signal is shown in Figures 4 (a-c). The sample of
graphic in Figure 4 is the output of Daubechis 1 DWT at 1st
to 3rd
level. The mother wavelet applied is
Daubechis 1-5, Coiflet 1-5 and Symlet 1-5. It means that vibation signal is filtered by Daubechis 1-5, Coiflet
1-5 and Symlet 1-5 as many as 3 levels, namely at 1st
-3rd
level. The amount of data generated and used is

965
reduced by half of the initial data at each level. Because these data are divided into HF signal and LF signal.
And at the next level, LF signal is used as input and produces HF signal and LF signal again. The resulting
data still looks like random. So, this data will then be retrieved its characteristics for processing.
3.2. Feature extraction
HF signals at 1st to 3rd
level resulted from the DWT process is extracted. Characteristics resulted are
sum, range, and energy of signal. The output of the signal features is shown in Tables 1-3. Normally, a motor
that experiences a misalignment will produce a higher vibration frequency. So that if it is processed using DWT
and its characteristics are taken, the value of its characteristics will be different from the characteristics of
a normal motor. This is shown in Table 1 Daubechis DWT at 1st level. The value of sum, range and energy
increases significantly from normal motor until 1.5 mm misalignment motor. It’s same for the other level and
for other kind of DWT in Table 2 and Table 3.
Figure 3. Vibration signal of induction motor
Table 1. Feature extraction of Daubechis 1 discrete wavelet transform
1st
Level 2nd
Level 3rd
Level
Sum Range Energy Sum Range Energy Sum Range Energy
Normal 0.1739 0.0183 0.0016 0.1100 0.0129 0.0007 0.0686 0.0092 0.0003
1mm 0.4209 0.0183 0.0039 0.2847 0.0259 0.0026 0.1739 0.0275 0.0016
1.5mm 0.5399 0.0549 0.0070 0.3429 0.0453 0.0038 0.1601 0.0229 0.0013
Table 2. Feature extraction of coiflet 1 discrete wavelet transform
1st
Level 2nd
Level 3rd
Level
Normal 0.2075 0.0223 0.0017 0.1057 0.0151 0.0005 0.0801 0.0171 0.0004
1mm 0.4992 0.0225 0.0034 0.3519 0.0271 0.0030 0.1975 0.0266 0.0017
1.5mm 0.6442 0.0496 0.0065 0.3493 0.0487 0.0036 0.1886 0.0241 0.0015
Table 3. Feature extraction of symlet 1 discrete wavelet transform
1st
Level 2nd
Level 3rd
Level
Normal 0.1739 0.0183 0.0016 0.1100 0.0129 0.0007 0.0686 0.0092 0.0003
1mm 0.4209 0.0183 0.0039 0.2847 0.0259 0.0026 0.1739 0.0275 0.0016
1.5mm 0.5399 0.0549 0.0070 0.3429 0.0453 0.0038 0.1601 0.0229 0.0013

 ISSN: 1693-6930
966
(a)
(b)
(c)
Figure 4. Daubechis 1 DWT (a) the first level (b) second level (c) third level
3.3. Discriminant analysis
QDA uses 12 training data on each normal motor, 1 mm misalignment and 1.5 mm misalignment.
So all training data amounted to 36 data. Furthermore, for each normal motor condition, 1mm misalignment
and 1.5 mm misalignment will be taken 8 data used as test data. So all test data amounted to 24 data.

967
As a comparison in measuring the accuracy of QDA, LDA is also used in processing the vibration data of
this motor. QDA and LDA processing is done using matlab software. QDA and LDA output are shown
in Tables 4-6.
Table 4. Classification outputs of Daubechis (Db) DWT
1st
Level 2nd
Level 3rd
Level
LDA(%) QDA(%) LDA(%) QDA(%) LDA(%) QDA(%)
Db 1 Error 0.000 4.167 12.500 8.333 8.333 8.333
Db 2 Error 8.333 8.333 20.833 20.833 33.333 20.833
Db 3 Error 0.000 0.000 8.333 8.333 29.167 8.333
Db 4 Error 4.167 0.000 4.167 0.000 8.333 8.333
Db 5 Error 12.500 0.000 12.500 8.333 12.500 12.500
Table 5. Classification outputs of Coiflet DWT
1st
Level 2nd
Level 3rd
Level
Coiflet 1 Error 4.167 4.167 8.333 4.167 25.000 16.667
Coiflet 2 Error 4.167 4.167 8.333 4.167 20.833 33.333
Coiflet 3 Error 4.167 4.167 8.333 0.000 25.000 29.167
Coiflet 4 Error 4.167 4.167 4.167 8.333 25.000 33.333
Coiflet 5 Error 0.000 4.167 4.167 0.000 25.000 25.000
Table 6. Classification outputs of Symlet DWT
1st
Level 2nd
Level 3rd
Level
Symlet 1 Error 8.333 8.333 0.000 0.000 12.500 12.500
Symlet 2 Error 4.167 4.167 8.333 16.667 16.667 12.500
Symlet 3 Error 4.167 4.167 8.333 4.167 12.500 8.333
Symlet 4 Error 4.167 4.167 4.167 4.167 29.167 37.500
Symlet 5 Error 4.167 8.333 0.000 8.333 29.167 29.167
The table of the results of the research that has been done, consists of 15 conditions on each mother
wavelet. 15 conditions are derived from variations from each mother wavelet, namely 5 types of mother
wavelets multiplied by the number of levels, namely 3 levels (1st
level to 3rd
level). From the results of
the research in the table above, we can see that the errors obtained from QDA and LDA using Daubechis,
Coiflet and Symlet DWT vary greatly. Text with blue blocks shows that LDA is more accurate than QDA and
text with green blocks shows QDA more accurately than LDA. Whereas colorless text indicates that the error
results from LDA and QDA are the same.
We can see that QDA is more accurate in classifying motor conditions with cases of misalignment by
processing data using Daubechis DWT. Based on Table 4, QDA is more accurate than LDA in 7 conditions,
namely on Db 4 and 5 at 1st
level and 2nd level, Db1 at 2nd
level, and Db 2 and 3 at 3rd
level. And the error
results are the same between LDA and QDA in 6 conditions. Whereas, 1 condition of LDA is more accurate.
From Table 6, we can see that LDA is more accurate than QDA in 4 conditions, namely on Symlet 2
at 2nd
level, Symlet 4 at 3rd
level, and symlet 5 at 1st
level and 2nd
level. And the error results are the same
between LDA and QDA in 8 conditions. And QDA is more accurate in 3 conditions. Whereas, in Table 5,
the processing of data uses Coiflet DWT, the results of the classification accuracy between QDA and LDA are
the same. But at the 1st
level, classification errors resulted evenly from Coiflet 1-5 are very minimum.
Whereas, when viewed from the accuracy of the classification results, namely the result of an error
that reaches 0%, processing data using Daubechis DWT is superior to other mother wavelets, which reaches
0% error in 5 conditions. The 0% error can be achieved using the Db1 at 1st
level with LDA, Db3 at 1st
level
with LDA and QDA, Db 4 and Db 5 at 1st
level with QDA and Db 4 at 2nd level with QDA. When using
Coiflet DWT, 0% error condition can be achieved on Coiflet 1 at 1st
level with LDA, and Coiflet 3 and coiflet
5 at 2nd
level with QDA. Meanwhile, the symlet DWT produces 0% error classification on symlet 1 at 2nd
level
with LDA and QDA, and syimlet 5 at 2nd
level with LDA.
In addition, from Tables 4-6, we can see that the classification results with the minimum error value
can be reached at the 1st level. While on the 3rd
level it produces a large enough error. It’s the same whether
the results are achieved by Daubechis, Symlet or Coiflet DWT. And finally, from the results of this research,
we find that Daubechis DWT at 1st level is the most accurate data processing in the case of misalignment on
induction motor compared to other mother wavelets. As well, QDA combined with Daubechis DWT produces
the lowest classification error. However, the ability to Coiflet 1-5 DWT at the 1st level, using the method of
either LDA or QDA also produces a low classification error.

 ISSN: 1693-6930
968
4. CONCLUSION
The failure of an induction motor is a problem that gives a huge loss in the industry. One type of
failure is misalignment on the induction motor. This study classifies misalignment in induction motors using
three types of wavelet transforms, namely Daubechis, Coiflet and Symlet DWT and multilevel decomposition
of mother wavelets, which is the 1st level to the 3rd level. The result shows that the 1st level of DWT produces
the highest classification error. Then, the best classification or the most minimum classification error is
produced by Daubechis DWT, especially those combined with Quadratic Discriminant Analysis (QDA). It
results 0-8.33% error, depend on kind of Daubechis DWT used. Moreover, Coiflet 1-5 DWT at the 1st level
produces a minimum classification error evenly. It results 4.17% of error.
However, further research needs to be done, with different induction motor power and more varied cases of
misalignment, as well as more data in order to reach more accurate conclusions. That is because the results of
the calcifications achieved in this study are still very varied.
REFERENCES
[1] Chourasia, A., Salunke, S., & Saxena, V., “Efficiency Optimization of Three Phase Induction Motor by Slip
Compensation: A Review,” International Journal of Electronics and Electrical Engineering, vol. 1, no. 4,
pp. 308–314, 2013.
[2] Kiliç, Erdal & Dogmus, Osman & Gani, Ahmet & Sit, Sami & Özçalik, Hasan, “Simulation and Experimental Study
of Vector Controlled Induction Motor Drive based on RBFNN-MRAC Controller,” International Advance Researches
& Engineering Congres, 2017.
[3] Tudorache T., Melscescu L., Petre V., “High efficiency squirrel cage induction machines,” Renewable Energy and
Power Quality Journal, vol. 1, no. 7, pp. 239–244, 2009.
[4] Harmouche J., Delpha C., & Diallo D., “Improved fault diagnosis of ball bearings based on the global spectrum of
vibration signals,” IEEE Transactions on Energy Conversion, vol. 30, no. 1, pp. 376–383, 2015.
[5] S. Barker, “Avoiding premature bearing failure with inverter fed induction motors,” Power Engineering Journal,
vol. 14, no. 4, pp. 182–189, 2000.
[6] EPRI, “Improved motors for utility applications,” Publication EL-2678-V1, ﬁnal report, 1982.
[7] D. A. Asfani, P. P. Surya Saputra, I. M. Yulistya Negara, I. G. N. Satriyadi Hernanda and R. Wahyudi, "Simulation
analysis on high impedance temporary short circuit in induction motor winding," 2013 International Conference on
QiR, Yogyakarta, pp. 202-207, 2013.
[8] Tagluk, Æ. M. E., “Bearing and misalignment fault detection in induction motors by using the space vector angular
fluctuation signal,” Electrical Engineering, vol. 87, no. 4, pp. 197–206, 2005.
[9] A. Starr B. K. N. Rao, “Condition Monitoring and Diagnostic Engineering Management,” Proceedengs of the 14th
Intrnational Congress, Elsevier, 2001.
[10] Jee-Hoon Jung, Lee Jong-Jae, Bong-Hwan Kwon, “Online Diagnosis of Induction Motors Using MCSA,” IEEE Trans.
Ind. Electron., vol. 53, no. 6, pp. 1842–1852, 2006.
[11] G. Acosta, C. Verucchi, E. Celso, “A current monitoring system for diagnosing electrical failures in induction motors,”
Mech. Syst. Signal Process., vol. 20, no.4, pp. 953–965, 2006.
[12] R. Obaid, T. Hableter, “Effect of Load on Detecting Mechanical Faults in Small Induction Motors,” Proceedings of
Symposium on Diagnostics for Electric Machines, Power Electronics and Drives, SDEMPED 2003, Atlanta,
pp. 307–311, 2003.
[13] Djamal E. C., Gustiawan D. P., & Djajasasmita D., “Significant variables extraction of post-stroke EEG signal using
wavelet and SOM kohonen,” TELKOMNIKA Telecommunication Computing Electronics and Control, vol. 17, no. 3,
pp. 1149–1158, 2019.
[14] Domy K., et. al., “Wavelet Based Feature Extraction for the Indonesian CV Syllables Sound,” TELKOMNIKA
Telecommunication Computing Electronics and Control, vol. 16, no. 3, pp. 925–933, 2018.
[15] Zhang, S., & Wang, A., “An Image Compression Method Based on Wavelet Transform and Neural Network,”
TELKOMNIKA Telecommunication Computing Electronics and Control, vol. 13, no. 2, pp. 587-596, 2015.
[16] Wang, L., Guo, H., & Zhang, S., “Motor Fault Diagnosis Based on Wavelet Transform,” TELKOMNIKA
Telecommunication Computing Electronics and Control, vol. 11, no. 9, pp. 5336–5343, 2013.
[17] Ramana D. V., Baskar S., “Incipient Fault Detection of the Inverter Fed Induction Motor,” International Journal of
Power Electronics and Drive Systems, vol. 8, no. 2, pp. 722–729. 2017.
[18] Saputra P. P. S., Misbah, eliyani, R. Firmansyah, D. Lastomo, “Haar and Symlet Discrete Wavelete Transform for
Identification Misalignment on Three Phase Induction Motor Using Energy Level and Feature Extraction,” Journal of
Physics: Conference Series, 2019.
[19] Anton Asfani, Dimas &Yulistya Negara, I Made & Surya, Pressa, “Short Circuit Detection in Stator Winding of Three
Phase Induction Motor Using Wavelet Transform and Quadratic Discriminant Analysis,” The 3rd
IIAE International
Conference on Intelligent Systems and Image Processing 2015, 2015.
[20] C. Jettanasen, A. Ngaopitakkul, D. A. Asfani and I. M. Y. Negara, "Fault classification in transformer using low
frequency component," 2017 IEEE 10th
International Workshop on Computational Intelligence and Applications
(IWCIA), Hiroshima, pp. 199-202, 2017.

969
[21] P. P. S. Saputra, F. D. Murdianto, R. Firmansyah and K. Widarsono, “Combination of Quadratic Discriminant
Analysis and Daubechis Wavelet for Classification Level of Misalignment on Induction Motor,” 2019 International
Symposium on Electronics and Smart Devices (ISESD), Badung-Bali, Indonesia, pp. 1-5, 2019.
[22] Cao X., Zhou S., Li J., & Zhang S., “Fault Diagnosis in Medium Voltage Drive Based on Combination of Wavelet
Transform and Support Vector Machine,” TELKOMNIKA Telecommunication Computing Electronics and Control,
vol. 14, no. 4, pp. 1284–1291, 2016.
[23] Johnson R. A., Wichern D. W., “Applied multivariate statistical analysis,” 4th
ed. Saddle River, NJ:
Prentice-Hall, 1998.
[24] C. Bouveyron, S. Girard, and C. Schmid, “High Dimensional Discriminant Analysis,” Communications in
Statistics-Theory and Methods,” vol. 36, no. 14, pp. 2607–2623, 2007.
[25] Saputra P. P. S., Firmansyah R., & Irawan D., “Various and multilevel of coiflet discrete wavelet transform and
quadratic discriminant analysis for classification misalignment on three phase induction motor,” Journal of Physics:
Conference Series, vol. 1367, no. 2019, pp. 1-11, 2019.
BIOGRAPHIES OF AUTHORS
Pressa Perdana Surya Saputra was born in klaten, Indonesia in 1988. He received his Master in
electrical engineering from ITS in 2014. Now he works as lecturer in UMG. His resarch interests
include renewable energy and energy conversion. However, now his research focuses on electrical
motor and his monitoring.
Misbah, born in Gresik, Indonesia in 1976. Received his Master in electrical engineering from
ITS in 2009. Worked as lecturer in UMG. Focus research is gas sensor. The focus of research in
the field of gas and odor sensors. Currently pursuing doctoral studies at ITS since 2017
Hendra Ariwinarno was born in Banyuwangi, Indonesia in 1980. His focus research is EMG
(Electromyogram) and its classification. In addition, he is an expert in electronics and
microprocessor.
Farid Dwi Murdianto. Received his Master in electrical engineering from ITS in 2015. Worked
as lecturer in Department of Electronic Engineering, Electronics Engineering Polytechnic Institute
of Surabaya. His focus research is renewable energy, especially wind turbin and photovoltaic, and
DC-DC converter.

Various and multilevel of wavelet transform for classification misalignment on induction motor with quadratic discriminant analysis

More Related Content

What's hot (20)

Similar to Various and multilevel of wavelet transform for classification misalignment on induction motor with quadratic discriminant analysis (20)

More from TELKOMNIKA JOURNAL (20)

Recently uploaded (20)

Various and multilevel of wavelet transform for classification misalignment on induction motor with quadratic discriminant analysis