Modelling of PV Array with MPP Tracking & Boost DC-DC Converter
1 like200 views
This document presents a model for a photovoltaic (PV) array with maximum power point tracking (MPPT) using a boost converter. It describes: 1) Modelling of PV cell, boost converter, and inverter components in MATLAB Simulink. 2) Development of an averaged model for a PV array connected to a boost converter with MPPT control using the incremental conductance algorithm. 3) Simulation results showing the model operating at maximum power point under changing irradiance conditions and having higher efficiency compared to without MPPT control.
![Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter
DOI: 10.9790/1676-10140713 www.iosrjournals.org 13 | Page
IV. Simulation Result
Table 1: Simulation Results.
V. Conclusion
Through the presented modelling we open the new door for High-Performance PV Projects. Hence, this
paper will be helpful for U.S. Department of Energy’s Sun-Shot Initiative to make large-scale solar energy
systems cost-competitive with the other sources of energy.
References
[1]. Gow, J.A. and C.D. Manning. "Development of a Photovoltaic Array Model for Use in Power-Electronics Simulation Studies."
IEEE Proceedings of Electric Power Applications, Vol. 146, No. 2, 1999, pp. 193–200.
[2]. Aryuanto Soetedjo, Abraham Lomi, Yusuf Ismail Nakhoda, Awan Uji Krismanto. “Modelling of Maximum Power Point Tracking
Controller for Solar Power System.” TELKOMNIKA, Vol.10, No.3, July 2012, pp. 419~430
[3]. Jiang Y, Qahouq J A A. “Study and evaluation of load current based MPPT control for PV solar systems.” Proceedings of IEEE
Energy Conversion Congress and Exposition. Arizona. 2011: 205-210.
[4]. Elgendy M A, Zahawi B, Atkinson D J. “Assesment of Perturb and Observe MPPT Algorithm Implementation Techniques for PV
Pumping Applications.” IEEE Transactions on Sustainable Energy. 2012; 3(1): 21-33.
SN.
pv
voltage(Vpv)
PV
current(Ipv)
Boost
efficiency
PV
power(Ppv)
PV Energy
(Epv)
Ideal PV
energy
(Eideal)
output
energy
(Eout)
(in Volt) (in Ampere) (in %) (in Watt) (in kWh) (in kWh) (in kWh)
Constant irradiance
1 The experiment result of
the model with MPPT
control
103.4 4.94 96.44% 510.8 4.081 4.087 3.936
2 The experiment result of
the model without
MPPT control
113.4 4 96.92% 455.2 3.642 4.087 3.56
Under time varying irradiance
3 The experiment result of
the model with MPPT
control
- - - - 2.558 2.673 2.46
4 The experiment result of
the model without
MPPT control
-3.658 4 - -14.63 1.788 2.673 1.755](https://image.slidesharecdn.com/b010140713-151119102800-lva1-app6892/85/Modelling-of-PV-Array-with-MPP-Tracking-Boost-DC-DC-Converter-7-320.jpg){kind=tracking}
Modelling of PV Array with MPP Tracking & Boost DC-DC Converter
- 1. IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-ISSN: 2278-1676,p-ISSN: 2320-3331, Volume 10, Issue 1 Ver. IV (Jan – Feb. 2015), PP 07-13 www.iosrjournals.org DOI: 10.9790/1676-10140713 www.iosrjournals.org 7 | Page Modelling of PV Array with MPP Tracking & Boost DC-DC Converter Mohammad Yasira , Faraz Khanb , Farazuddin Siddiquic* a Student M.tech (Power System), AIET, Lucknow (U.P.), India b Lab Instructor (Electronic & Simulation Lab), Integral University, Polytechnic Campus Shahjahanpur (U.P.), India c Lecturer (Electrical), Integral University, Polytechnic Campus Shahjahanpur (U.P.), India Abstract: In any solar plant output of PV arrays varies due to change of solar irradiance and other conditions. Therefore, the maximum power point tracking algorithm is implemented in DC-DC converter to enable PV arrays to operate at maximum power point. This paper presents the averaged model for PV array with Maximum Power Point Tracking (MPPT) boost converter. This model consists of PV module and MPPT boost DC-DC converter. The incremental conductance algorithm is employed to control the boost converter. Instantaneous report of system stability & efficiency is stimulated under the normal variation of solar irradiance or in any condition through MATLAB simulation. Keywords: Maximum Power Point Tracking (MPPT) Boost converter ; Solar cell model ; Solar cell connected with Grid & PV array averaged Model,; Switched-mode Boost DC-DC converter; Distributed Generation (DG), Incremental Conductance (IC) algorithm; Concentrating Solar Plant(CSP). I. Introduction Photovoltaic (PV) researches of this age are focusing upon boosting solar cell conversion efficiencies, lowering the cost of solar cells, modules, and systems, and improving the reliability of PV systems as well as components. We effort to contribute these goals through Modelling of grid connected PV system. To achieve the goal of maximum efficiency, it is necessary to track this maximum power point (MPP) called as MPPT (Maximum Power Point Tracking). Here PV module, DC-DC converter and MPPT (P&O algorithm) are modelled using MATLAB Simulink. Since the main focus is on tracking the MPP by adjusting the duty cycle of DC-DC converter. Generally MPPT techniques are employed through two ways: (1) by hardware implementation and (2) by software modelling. Software modelling of equation model is used here by using block or subsystem to represent these system equations. We try best to control duty cycle & hence the output voltage of PV in modelling of DC-DC converter. In general it is preferred to employ circuit model for modelling the DC-DC converter modelling but when we analyse this under circuit model we face several difficulties of it. Such as: a) It is supported by the limited software; b) It is difficult to modify the model; c) It avoids for creating the new model. So the main aim of the paper is the modelling of DC-DC converter using equation modelling to track the MPP of PV module/array, which allows the input voltage of the DC-DC converter to be controlled by MPPT algorithm. II. Modelling of Components a) Simple PV cell (ECEN2060) Figure 1: Simple PV cell Simulink model(Simulation stop time: t =1)
- 2. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 8 | Page Figure 2: I-V Characteristics (Result of fig 1) Figure 3: P-V Characteristics (Result of fig 1) b) Dc-Dc Boost Converter Figure 4: Switched Mode Boost DC-DC converter with inductor current control (averaged Model) t=2/60.
- 3. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 9 | Page Figure 5: Result of fig 4 (Vout= 199.8, Efficiency=0.9592, Pout= 599.5) C) Dc-Ac Inverter Figure 6: Switched-Mode DC-AC Inverter for grid connected system (averaged model) t=1/60 Figure 7: Result of fig 6 (Pin= 566.2 Efficiency=0.9537 Pout=540) Figure 8: Switching-Mode DC-AC Inverter for grid connected system t=1/60
- 4. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 10 | Page Figure 9: Result of fig 8 III. Modelling for PV array with MPPT DC-DC Boost converter Figure 80: Averaged Model for PV array with MPP tracking Boost DC-DC converter t=60*8
- 5. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 11 | Page Figure 11: The experiment result of the model with MPPT control under constant weather
- 6. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 12 | Page Figure 9: The experiment result of the model without MPPT control under constant weather Figure 10: The experiment result of the model without MPPT control under time varying weather Figure 11: The experiment result of the model with MPPT control under time varying weather
- 7. Modelling Of PV Array with MPP Tracking & Boost DC-DC Converter DOI: 10.9790/1676-10140713 www.iosrjournals.org 13 | Page IV. Simulation Result Table 1: Simulation Results. V. Conclusion Through the presented modelling we open the new door for High-Performance PV Projects. Hence, this paper will be helpful for U.S. Department of Energy’s Sun-Shot Initiative to make large-scale solar energy systems cost-competitive with the other sources of energy. References [1]. Gow, J.A. and C.D. Manning. "Development of a Photovoltaic Array Model for Use in Power-Electronics Simulation Studies." IEEE Proceedings of Electric Power Applications, Vol. 146, No. 2, 1999, pp. 193–200. [2]. Aryuanto Soetedjo, Abraham Lomi, Yusuf Ismail Nakhoda, Awan Uji Krismanto. “Modelling of Maximum Power Point Tracking Controller for Solar Power System.” TELKOMNIKA, Vol.10, No.3, July 2012, pp. 419~430 [3]. Jiang Y, Qahouq J A A. “Study and evaluation of load current based MPPT control for PV solar systems.” Proceedings of IEEE Energy Conversion Congress and Exposition. Arizona. 2011: 205-210. [4]. Elgendy M A, Zahawi B, Atkinson D J. “Assesment of Perturb and Observe MPPT Algorithm Implementation Techniques for PV Pumping Applications.” IEEE Transactions on Sustainable Energy. 2012; 3(1): 21-33. SN. pv voltage(Vpv) PV current(Ipv) Boost efficiency PV power(Ppv) PV Energy (Epv) Ideal PV energy (Eideal) output energy (Eout) (in Volt) (in Ampere) (in %) (in Watt) (in kWh) (in kWh) (in kWh) Constant irradiance 1 The experiment result of the model with MPPT control 103.4 4.94 96.44% 510.8 4.081 4.087 3.936 2 The experiment result of the model without MPPT control 113.4 4 96.92% 455.2 3.642 4.087 3.56 Under time varying irradiance 3 The experiment result of the model with MPPT control - - - - 2.558 2.673 2.46 4 The experiment result of the model without MPPT control -3.658 4 - -14.63 1.788 2.673 1.755