Paper on synthesis of zeolite and application

Chemical and Process Engineering Research www.iiste.org
ISSN 2224-7467 (Paper) ISSN 2225-0913 (Online)
Vol 2, 2012

A Study on Synthesis of Zeolite and Removal of Amido Black
dye by adsorption with Zeolite
Ameen Sayal*, Vijaya Kumar Bulasara, Sanghamitra Barman
Department of Chemical Engineering, Thapar University, Patiala
ameen.sayal@gmail.com
Abstract
Investigations have been undertaken to determine whether cheap, commercially available materials (natural
zeolite and bentonite) hold promise in the treatment of wastewaters from the textile industry. The initial
findings indicate that zeolite synthesized from fly ash has high adsorptive capacity for dyes and it is
relatively cheap. The adsorption of two basic dyes (Amido Black and Thionine) onto granular activated
carbon as well as zeolite from fly ash and bentonite has to be studied as single equilibrium isotherms. The
effectiveness of each adsorbent has to be measured in terms of its adsorption capacity towards individual
constituents of the effluent. The adsorption isotherm would be described by the Langmuir and Freundlich
isotherm equations. The parameters in the adsorption isotherms will be estimated from the experimental
equilibrium data using non-linear regression analysis. Using these data, the selection of the best adsorbent
can be done for design purposes.
Keywords: Natural Zeolite, bentonite, Amido Black, Thionine, Langmuir, Freundlich, granular activated
carbon

1. Introduction
Adsorption has been found to be superior to other techniques for water re-use in terms of initial cost,
simplicity of design, ease of operation and insensitivity to toxic substances. Activated carbon is the most
popular adsorbent and has been used with great success, but is expensive [6]. A full description of low cost
adsorbents for waste and wastewater treatment: a review has been presented by S.J.T. Pollard et al (2007)
[11]. A number of studies have been reported with regard to the adsorption equilibrium of dye removal
processes using various adsorbents. In most adsorption systems of dyestuffs-adsorbent, Langmuir [3,9,10],
Freundlich [2,9,10], and Redlich-Peterson [1,6,7,8,10] isotherms have been applied to describe equilibrium
between liquid–solid phases. Two intra-particle diffusion mechanisms are involved in the adsorption rate
(a) diffusion within the pore volume known as pore diffusion, and (b) diffusion along the surface of pores
known as surface diffusion [13]. Some of the investigators have applied the pore diffusion model with and
without film resistance [3]. McKay has developed homogeneous solid phase diffusion model to describe
systems dyes on bagasse pith (2011) [7]. The homogeneous solid phase diffusion model has been
developed based on external mass transfer and surface diffusion by M.S.El-Geundi [1]. He has applied this
model for adsorption of basic dyes onto natural clay in a batch adsorber. The branched pore kinetic model
was used to describe the adsorption of cobalt phthalocyanine dye onto active carbon and basic dyes onto
natural clay [2].
Research has already been carried out using different treatment technologies e.g. chemical coagulation-
flocculation [2], different types of oxidation processes [3], biological processes [4], membrane based
separation processes [5–7], adsorption [8] etc. for the removal of colored dye from wastewater. Research is
focused on the use of low-cost, reusable, locally available, biodegradable adsorbents made from natural
sources. Natural and modified clays, zeolite from fly ash and bentonite are being considered as alternative
low-cost adsorbents. Adsorption of organic molecules to an adsorbent depends on various factors like
temperature, pH of the solution, the structure and concentration of the adsorbing molecule, the ionic
strength of the suspension, and the structure of the adsorbent. Experimental investigations have been
carried out to adsorb Amido Black dye from aqueous medium using zeolite as an adsorbent.
Characterization of zeolite is to be done by measuring
 Particle size distribution using particle size analyzer
 BET surface area using BET surface analyzer
 Structural analysis using X-ray diffractometer
 Microscopic analysis using scanning electron microscope.

54

Vol 2, 2012

 The effects of initial dye concentration, contact time, zeolite loading, stirring speed, pH, and
temperature are to be studied for the adsorption of Amido Black in batch mode.
 Comparison of adsorption capacity of zeolite with other adsorbent such as activated carbon
The aim of this work is to study the ability of zeolite synthesized from fly ash to remove the acidic dye
Amido Black from aqueous solutions. This adsorbent was chosen because of its cheapness and abundance.

II Description of Materials

A. ZEOLITES

The types of zeolites formed on treatment are very much selective to reaction parameters and also the raw
material compositions. The synthesis of various zeolites from fly ash and their properties mainly depend on
the effect of reaction time, reaction
temperature, alkalinity and fly ash composition.

Zeolites are crystalline, micro-porous, hydrated aluminosilicates that are built from an infinitely extending
three-dimensional network of [SiO4]4- and [AlO4]4- tetrahedral linked to each other by the sharing of oxygen
atom. Generally, their structure can be considered as inorganic polymer built from tetrahedral TO 4 units,
where T is Si4+ or Al3+ ion. Each oxygen (O) atom is shared between two T atoms.

Mx/n[(AlO2x(SiO2)y]· 2O, where M is an alkali or alkaline earth cation, n is the valence of the cation, w
wH
is the number of water molecules per unit cell, x and y are the total number of tetrahedra per unit cell, and
the ratio y/x usually has values of 1 to 5, though for the silica zeolite, y/x can be raging from 10 to 100.

The adsorption of dyes onto zeolites has been extensively investigated by some researcher but only a few
studies have been reported about the adsorption of dye onto fly ash-based zeolites .A comparison of the
adsorption capabilities of Amido Black with other larger dyes over zeolites and activated carbon will
provide valuable information about adsorption mechanisms and the structure of the zeolites. The structure
of zeolite is given in fig.1.

Adsorption and adsorption processes are important fields of study in physical chemistry. They form the
basis for understanding phenomena such as heterogeneous catalysis, chromatographic analysis, dyeing of
textiles, and clarification of various effluents.

Dyes are defined as colored substances which when applied to fibers give them a permanent color, i.e.
resistant to action of light, water and soap. Practically every dyestuff is made from either one or more of
the compounds obtained by the distillation of the coal tar. The chief of these are Benzene (C6H6), Toluene
(C6H5.CH3), Naphthalene (C10H8), Anthracene (C14H10), Phenol (C6H5OH), Cresol (C7H7OH), Acridine
(C13H9N), and Quinoline (C9H7N). Wastewaters from dyeing and finishing operations in the textile industry
are generally high in both color and organic content. Color removal from textile effluent has been the target
of great attention in the last few years, not only because of its potential toxicity, but also mainly due to its
visibility problems. Recent estimate indicates that 20% of dyes enter the environment through effluent that
result from the treatment of industrial wastewater. The existing technologies have certain efficiency in the
removal of dyes but their initial and operational costs are very high. On the other hand, low cost
technologies do not allow the desired degree of color removal or have certain disadvantage. Oxidation and
adsorption are two major technologies that are used for wastewater treatment in the textile industry. Among
oxidation methods, UV/Ozone and UV/H2O2 treatments are technologies for decolorizing wastewater.
Adsorption is rapidly becoming a prominent method of treating
aqueous effluents and it has been extensively used in industrial processes for a variety of separation and
purification purposes. Adsorption of dyes by zeolites has evolved into one of the most effective physical
process for the decolorization of textile wastewater. This process has been found to be superior to other

55

Vol 2, 2012

techniques for water re-use in terms of initial cost, simplicity of design, ease of operation and insensitivity
to toxic substances.
B. TYPES OF ZEOLITE
The following table presents the most common types of zeolites in table 1.

C. AMIDO BLACK DYE

Amido black 10B is an amino acid staining diazo dye. Its molecular formula is C22H14N6Na2O9S2. Amido
Black 10B is a synthetic acid dye containing both NN and CC chromophore groups (pyrazolone dye). It is a
dark red to black powder soluble in water and used as a stain for protein-containings. Its chemical
designation is 4-amino-5-hydroxy- 3-[(4-nitrophenyl) azo]- 6-(phenylazo)- 2,7-naphthalene disulfonic acid
disodium salt. Acid dyes are water-soluble dyes employed mostly in the form of sodium salts of the
sulfonic or carboxylic acids. They are anionic which attach strongly to cationic groups in the fibre directly.
They can be applicable to all kind of natural fibres
like wool, cotton and silk as well as to synthetics like polyesters, acrylic and rayon. However, they are not
substantive to cellulosic fibres. They are also used in paints, inks, plastics and leather. Chemical structure
of Amido Black dye is shown in fig.2.

III. Experimental Methodology

Process flow diagram for synthesis of zeolite from fly ash is shown in fig.3.

A. ZEOLITE SYNTHESIS:

Before any treatment, the raw fly ash samples were first screened through a BSS Tyler sieve of 80-mesh
size to eliminate the larger particles. The unburnt carbon (4–6%) along with other volatile materials present
in fly ash were removed by calcination at 800 (± 10) ° for 2 h.Mixture of sodium hydroxide and fly ash
C
(calcined and HCl treated) in a pre-determined ratio, was milled and fused in a stainless steel tray at
different temperatures ranging from 500–650° for 1 h. The sodium hydroxideto fly ash ratio (by weight)
C
was varied from 1× 0–1× The resultant fused mixture was then cooled to room temperature, ground
5.
further and added to water (10 g fly ash/100 ml water). The slurry thus obtained was agitated mechanically
in a glass beaker for several hours. It was then kept at around 90° for 6 h without any disturbance. The
C
flow diagram of the synthesis process is shown in figure 3.
The resultant precipitate was then repeatedly washed with distilled water to remove excess sodium
hydroxide, filtered and dried. The sodium hydroxide added to the fly ash not only works as an activator, but
also adjusts the sodium content in the starting material.

IV. Results and Discussion

A. DETERMINATION OF λmax FOR AMIDO BLACK DYE SOLUTION

To determine the wavelength that corresponds to maximum absorbance (λmax), a standard solution of
Amido Black in distilled water was scanned through a wavelength range of 200–700 nm using a UV–
Visible spectrophotometer. Maximum absorbance value was noticed at a wavelength of 618 nm (Figure 1).
The same value was also used in several literatures (Qiu et al., 2009). Therefore, λmax for amido black was
taken as 618 nm. A plot of absorbance versus wavelength for Amido Black dye solution is given in fig.4.

B. CALIBRATION CURVE FOR AMIDO BLACK DYE SOLUTION

Absorbance values were determined at various known concentrations of the dye solution to obtain a
calibration curve for Amido Black dye solution. As shown in figure 2, a linear fit to the observed data

56

Vol 2, 2012

(absorbance versus dye concentration) yielded a straight line with a slope of 0.0658. This calibration curve
can be used for the determination of unknown dye concentration in the solution after adsorption with
zeolite. A calibration curve for amido black dye solution is shown in fig 5.

C. ADSORPTION EXPERIMENTS

The adsorption experiments were carried out for 6 h under continuous agitation at 120 rpm and 20C. The
experimental scheme is as follows.

Six different concentrations of the adsorbent (zeolite) were studied to obtain the optimal concentration of
the zeolite for effective removal of the dye from its aqueous solution.

D. CALCULATION OF REMOVAL EFFICIENCY

Dye removal efficiency was determined from the dye concentration in the solution before and after
adsorption with zeolite.
 Ci  C f 
Removal efficiency, R    100
 Ci  (1)
Ci  C f
Adsorption capacity, q t 
Cz (2)
Here,
Ci = initial dye concentration in the solution, mg/L
Cf = dye concentration in the solution after adsorption with zeolite, mg/L
Cz = zeolite loading (adsorbent dosage), g/L
qt = amount of dye adsorbed per unit weight of zeolite, mg/g

The values of dye removal efficiency and adsorption capacity of zeolite evaluated using the above formulae
(Eq. 1–2) for various concentrations of zeolite were presented in table 3.
A plot of dye removal efficiency versus zeolite concentration yielded a non-linear profile as shown in
figure 3. From this figure, it can be observed that the removal efficiency increased with increasing the
zeolite concentration up to 10 g/L and no significant improvement in the removal efficiency values was
observed beyond this value. Hence, the optimal zeolite concentration for Hence, the optimal zeolite
concentration for the removal of Amido Black dye was chosen to be 10 g/L. A variation of dye removal
efficiency with zeolite concentration is given in fig.6.

As can be seen from figure 5, the adsorption capacity of the zeolite (determined by Eq. (2)) decreased with
increasing the zeolite concentration. This observation is also in good agreement with the literature [xx]. It
indicates that the adsorption capacity of a zeolite decreases with increasing the zeolite dosage. Hence, it can
be concluded that too much of zeolite concentration in the solution is not effective for adsorption and it is
also not economical. A variation of adsorption capacity with zeolite concentration is given in fig.7.

Zeolitized fly ash product is successfully used as low cost adsorbent for this anionic dye. Equilibrium and
kinetic results obtained in this study may be useful for designing a treatment plant for dye removal from
industrial colored effluents.

V. Conclusions

The following conclusions have been derived from the experimental analysis carried out so far.
 Zeolite has been synthesized from low-cost raw material, i.e. fly ash.

57

Vol 2, 2012

 The prepared zeolite has been successfully applied for the adsorptive removal of Amido Black dye
from its aqueous solutions.
 The prepared fly ash based zeolite is found to be more effective than the natural zeolite
clinoptilolite presented in the literature (Qiu et al., 2009).
 The optimum zeolite concentration obtained from the experimental studies for Amido Black is 10
g/L.
 λmax for Amido Black 10B dye solution was found to be 618 nm.
Most important observation in this work is that the zeolite synthesized from fly ash could act as a very
effective adsorbent for the removal of Amido Black dye. The removal efficiency increased with increasing
the zeolite concentration significantly and reached a value as high as 74% at lower concentrations (up to 10
g/L) where as no significant change was observed at higher concentrations.
Work done so far includes the preparation of zeolite and studying the effect of zeolite loading on the
removal of Amido Black dye by varying the zeolite concentration from 0 to 15 g/L.

VI. Acknowledgement

This work was supported by Thapar University under Research Fellowship Programme.
References

1. Senthilkumar, S., Perumalsamy, M., Prabhu, H.J., Decolourization potential of white-rot fungus
Phanerochaete chrysosporium on synthetic dye bath effluent containing Amido black 10B, Journal
of Saudi Chemical Society, In Press, doi:10.1016/j.jscs.2011.10.010.
2. Ahmad, R., Kumar, R., Conducting Polyaniline/Iron Oxide Composite: A Novel Adsorbent for the
Removal of Amido Black 10B, J. Chem. Eng. Data 55, 3489–3493 (2010).
3. Qiu, M., Qian, C., Xu, J., Wu, J., Wang, G., Studies on the adsorption of dyes into clinoptilolite,
Desalination 243, 286–292 (2009).
4. Jian-Hui Sun , , Sheng-Peng Sun, Guo-Liang Wang, Li-Ping Qiao (2007),” Degradation of azo dye
Amido black 10B in aqueous solution by Fenton oxidation process”; Dyes and Pigments
5. Volume 74, Issue 3, , Pages 647-652.
6. Peng Liu, Liuxue Zhang (2007),” Adsorption of dyes from aqueous solutions or suspensions with
clay nano-adsorbents”; Separation and Purification Technology, Volume 58, Issue 1, , Pages 32-39.
7. Gülten Atun, Gül Hisarlı, Ayşe Engin Kurtoğlu, Nihat Ayar (2011) “A comparison of basic dye
adsorption onto zeolitic materials synthesized from fly ash”; Journal of Hazardous Materials,
Volume 187, Issues 1-3, Pages 562-573.
8. Yamin Yasin, Abd. Hafiz Abd. Malek, and Siti Mariam Sumaria, “ Removal of Amido Black
Dye from Aqueous Solution by Uncalcined and Calcined Hydrotalcite “; AIP Conf. Proc- June 1,
2009 -- Volume 1136, pp. 533-539.
9. Youji Li, Xiaodong Li, Junwen Li, Jing Yin (2006),” Photocatalytic degradation of methyl orange
by TiO2-coated activated carbon and kinetic study”; Water Research, Volume 40, Issue 6, , Pages
1119-1126.
10. Nourali Mohammadi, Hadi Khani, Vinod Kumar Gupta, Ehsanollah Amereh, Shilpi Agarwal
(2011),’ Adsorption process of methyl orange dye onto mesoporous carbon material–kinetic and
thermodynamic studies “; Journal of Colloid and Interface Science, Volume 362, Issue 2, Pages
457-462.
11. Alok Mittal, Arti Malviya, Dipika Kaur, Jyoti Mittal, Lisha Kurup (2007),” Studies on the
adsorption kinetics and isotherms for the removal and recovery of Methyl Orange from
wastewaters using waste materials “;Journal of Hazardous Materials, Volume 148, Issues 1-2,
Pages 229-240.
12. Suhong Chen, Jian Zhang, Chenglu Zhang, Qinyan Yue, Yan Li, Chao Li (2010),” Equilibrium
and kinetic studies of methyl orange and methyl violet adsorption on activated carbon derived from
Phragmites australis “;Desalination, Volume 252, Issues 1-3, Pages 149-156.

58

Vol 2, 2012

13. Mohd. Rafatullah, Othman Sulaiman, Rokiah Hashim, Anees Ahmad (2010),” Adsorption of
methylene blue on low-cost adsorbents: A review “;Journal of Hazardous Materials, Volume 177,
Issues 1-3, Pages 70.
14. Runping Han, Jingjing Zhang, Pan Han, Yuanfeng Wang, Zhenhui Zhao, Mingsheng Tang
(2009),” Study of equilibrium, kinetic and thermodynamic parameters about methylene blue
adsorption onto natural zeolite “;
15. Chemical Engineering Journal, Volume 145, Issue 3, Pages 496-504.
16. Shaobin Wang, Lin Li, Hongwei Wu, Z.H. Zhu (2005),” Unburned carbon as a low-cost adsorbent
for treatment of methylene blue-containing wastewater “;Journal of Colloid and Interface Science,
Volume 292, Issue 2, Pages 336-343.
17. Mehmet Ulas Dural, Levent Cavas, Sergios K. Papageorgiou, Fotis K. Katsaros (2011),”
Methylene blue adsorption on activated carbon prepared from Posidonia oceanica (L.) dead leaves:
Kinetics and equilibrium studies”;
18. Chemical Engineering Journal, Volume 168, Issue 1, Pages 77-85.
19. K. Vasanth Kumar, V. Ramamurthi, S. Sivanesan (2005),’ Modeling the mechanism involved
during the sorption of methylene blue onto fly ash “;Journal of Colloid and Interface Science,
Volume 284, Issue 1, Pages 14-21.
20. J.X. Lin, S.L. Zhan, M.H. Fang, X.Q. Qian,H Yang (2008),” Adsorption of basic dye from aqueous
solution onto fly ash “;Journal of Environmental Management, Volume 87, Issue 1, Pages 193-
200.
21. Shaobin Wang, Qing Ma, Z.H. Zhu (2008),’ Characteristics of coal fly ash and adsorption
application”;
22. Fuel, Volume 87, Issues 15-16, Pages 3469-3473.

59

Vol 2, 2012

List of Table
Table Title Page No.

1 Typical oxide formula of some synthetic zeolites 09

2 Calculation of absorbance of amido black dye from dye concentration 09

3 Calculation of adsorption capacity using solutin concentration 09

4 Calculation of dye removal efficiency from Zeolite concentration 10

List of Figures
Figure Title Page No.

1 Primary building unit of zeolite structure 10

2 Structure of Amido Black 10B dye 10

3 Flow sheet of synthesis of Zeolite from fly ash 11

4 A plot of absorbance versus wavelength for Amido Black dye solution 11

5 Calibration curve for amido black dye solution 12

6 12
Variation of dye removal efficiency with zeolite concentration
7 12
Variation of adsorption capacity with zeolite concentration

Tables

Table 1
Zeolites Typical oxide formula

Zeolites A Na2O.Al2O3.2SiO2.4.5H2O

Zeolites X Na2O.Al2O3.2.5SiO2.6H2O

Zeolites Y Na2O.Al2O3.4.8SiO2.8.9H2O

60

Vol 2, 2012

Table 2

Dye Concentration, mg/L Absorbance, A.U.

5.0 0.329
10.0 0.658
15.0 0.987
20.0 1.316
25.0 1.645
30.0 1.974
35.0 2.303
45.0 2.961
50.0 3.290

Table 3

Zeolite Solution Adsorption
concentration concentration capacity
(g/L) (mg/L) (mg/g)
0 20.2 –
2.5 14.5 2.3
5 9.1 2.2
7.5 6.5 1.8
10 5.3 1.5
12.5 5.5 1.2
15 4.9 1.0

Table 4

Zeolite concentration Removal efficiency
(g/L) (%)
0 0
2.5 28.3
5 54.9
7.5 68.0
10 73.8
12.5 73.0
15 75.9

61

Vol 2, 2012

Figures

Fig.1

Fig.2

62

Vol 2, 2012

FLY ASH
NaOH (S)

MIXIING

FUSION

GRINDING
WATER
STIRRING AT ROOM TEMPERATURE (AGING)

CURING AT 363K

FILTERATION

WASHING

DRYING AT 353K

ZEOLITE X
Fig.3

4

3.5

3
Absorbance, A.U.

2.5

2

1.5

1

0.5 lmax = 618 nm

0
200 250 300 350 400 450 500 550 600 650 700

Wavelength, nm

Fig.4

63

Vol 2, 2012

4
y = 0.0658x
3.5
R2 = 0.9995
3
Absorbance, A.U.

2.5

2

1.5

1

0.5

0
0 10 20 30 40 50 60

Dye Concentration, mg/L

Fig.5

90
80
Removal efficiency, %

70

60
50

40

30
20
10

0
0 2 4 6 8 10 12 14 16

Zeolite concentration, g/L

Fig.6

3.0
Adsorption capacity, mg/g

2.5

2.0

1.5

1.0

0.5

0.0
0 2 4 6 8 10 12 14 16

Zeolite concentration, g/L

Fig.7

64

This academic article was published by The International Institute for Science,
Technology and Education (IISTE). The IISTE is a pioneer in the Open Access
Publishing service based in the U.S. and Europe. The aim of the institute is
Accelerating Global Knowledge Sharing.

More information about the publisher can be found in the IISTE’s homepage:
http://www.iiste.org

The IISTE is currently hosting more than 30 peer-reviewed academic journals and
collaborating with academic institutions around the world. Prospective authors of
IISTE journals can find the submission instruction on the following page:
http://www.iiste.org/Journals/

The IISTE editorial team promises to the review and publish all the qualified
submissions in a fast manner. All the journals articles are available online to the
readers all over the world without financial, legal, or technical barriers other than
those inseparable from gaining access to the internet itself. Printed version of the
journals is also available upon request of readers and authors.

IISTE Knowledge Sharing Partners

EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open
Archives Harvester, Bielefeld Academic Search Engine, Elektronische
Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial
Library , NewJour, Google Scholar

Paper on synthesis of zeolite and application

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Paper on synthesis of zeolite and application (20)

More from Alexander Decker (20)

Recently uploaded (20)

Paper on synthesis of zeolite and application