Particle Swarm Optimization for the Path Loss Reduction in Suburban and Rural Area

International Journal of Electrical and Computer Engineering (IJECE)
Vol. 7, No. 4, August 2017, pp. 2125~2131
ISSN: 2088-8708, DOI: 10.11591/ijece.v7i4.pp2125-2131  2125
Journal homepage: http://iaesjournal.com/online/index.php/IJECE
Particle Swarm Optimization for the Path Loss Reduction in
Suburban and Rural Area
Messaoud Garah1
, Houcine Oudira2
, Lotfi Djouane3
, Nazih Hamdiken4
1,2,3
Electronic Departement, University Mohamed Boudiaf- M’Sila, Algeria
4
Electronic Departement, University of- Batna, Algeria
Article Info ABSTRACT
Article history:
Received Jan 18, 2017
Revised Mar 21, 2017
Accepted Apr 13, 2017
In the present work, a precise optimization method is proposed for tuning the
parameters of the COST231 model to improve its accuracy in the path loss
propagation prediction. The Particle Swarm Optimization is used to tune the
model parameters. The predictions of the tuned model are compared with the
most popular models. The performance criteria selected for the comparison
of various empirical path loss models is the Root Mean Square Error
(RMSE). The RMSE between the actual and predicted data are calculated for
various path loss models. It turned out that the tuned COST 231 model
outperforms the other studied models.
Keyword:
Empirical models
Obtimization
Path loss
PSO algorithm
Copyright © 2017 Institute of Advanced Engineering and Science.
All rights reserved.
Corresponding Author:
Messaoud Garah,
Faculty of Technology, Electronic Departement,
University Mohamed Boudiaf- M’Sila,
Université Med BOUDIAF-BP 166 M'sila 28000, Algeria.
Email: messa.gareh@gmail.com
1. INTRODUCTION
The need for connectivity anywhere, added to the increment in the number of users, has triggered
the development of various generations of mobile communication standards in the last decades. The demand
for greater traffic capacity involving both voice and data transmission requires the planning of mobile
communication networks comprised of smaller and smaller cells, thus making the number of base stations
grow exponentially, and complicating the process of determining and optimizing the location of these
stations. Because of this, accurate and fast prediction models are needed for making received signal
level/path loss predictions prior to actual network deployment [1], [2].
In this paper, we analyze the performance achievable with an intermediate technique, between
purely empirical models [3], [4] and real measure established from the field of study, based on the use of
Particle Swarm Optimization.
In the last few years, many researchers have applied several techniques for predicting the path loss
environments [5-7]. In the above references, extensive descriptions and GA optimizations and other methods,
have been presented. However, optimized model can provide optimal parameters for radio-wave path-loss
predicting in the target area. This is the main issue discussed in this paper.
The rest of this paper is organized as follows. In section 2 and 3 we review each empirical model
and the PSO method. section 4 presents the application, results and discussion. Finally, in the last section we
present our conclusion.

 ISSN: 2088-8708
IJECE Vol. 7, No. 4, August 2017 : 2125 – 2131
2126
2. PARTICLE SWARM OPTIMIZATION
The Particle swarm optimization is a population-based algorithm for searching global optimization
problems developed by Kennedy and Eberhart in 1995 [8]. PSO utilizes a population (called swarm) of
particles in the search space. The status of each particle is characterized according to its position and
velocity. ⃗⃗⃗ ( ) , and the velocity of particle i is represented as
⃗⃗⃗ ( ). To discover the optimal solution, each particle changes its searching direction
according to two factors: The best position of a given particle and the best position obtained by the swarm
(global pest) . PSO searches for the optimal solution by updating the velocity and position of each particle
according to the following Equations [9].
( ) ( ) ( ) (1)
( ) ( ) ( ( ) ( )) ( ( ) ( )) (2)
Where t denotes the iteration in the evolutionary space, w is the inertia weight, C1 and C2 are personal and
social learning factors, and are random values uniformly distributed within the range [0, 1].
The basic process of the PSO algorithm is given as follows:
a. Initialization: Particles are initialized with random positions and velocities.
b. Evaluation: The value of objective function is measured for each particle.
c. Find the : If the value of objective function for particle i is better than the of particle i, the
current value of objective function is set as the new of particle i.
d. Find the : If any pbest is better than the , is set to the current value.
e. Update velocity and position: The velocity of each particle is updated according to Equation (1),
and the particle is moved to the next position according to Equation (2).
f. Stopping criterion: If the number of iterations is met, the algorithm will be stopped; otherwise it
will be returned to step 2.
3. PATH LOSS MODEL
Empirical models describe from a statistical point of view the relationship between the path loss and
the environment. Results are usually obtained by means of measurement campaigns. In this paper, we have
considered four various Empirical models for our study as follows.
3.1. Egli Model
Egli prediction model is an empirical model which has been proposed by [10]. The Egli model is a
simplistic model to approach radio-wave path-loss of irregular topography. Based on real data, the path-loss
approaching can be formulated as following
( ) ( ) ( ) {
( )
( )
(3)
where
= height of the base station antenna. Unit: meter (m)
= height of the mobile station antenna. Unit: meter (m)
= distance from base station antenna. Unit: meter (km)
f = frequency of transmission. Unit: megahertz (MHz
3.2. Hata’s Model
This model has been introduced to urban areas; and with some correction factors it could be
extended to suburban and rural areas. For urban area the median path loss Equation is given by
( )( )
( ) ( ) ( ) ( ( )) (4)
For suburban area, it is expressed as
( )( ) ( ) ( ) (5)

IJECE ISSN: 2088-8708 
Particle Swarm Optimization for the Path Loss Reduction in Suburban and Rural Area (Messaoud Garah)
2127
Finally, for open rural area, it is modiﬁed as
( )( ) ( ) ( ( )) ( ) (6)
In the above Equations, d is the transmitter-receiver antenna separation distance and it is valid for
1km–20km, fc represents the operating frequency from150 MHz to 1500 MHz. The transmit antenna height,
ranges from 30m to 200m and the receive antenna height, ranges from 1m to 10m are considered
[11], [12].
3.3. Cost 231 Hata model
The COST 231 is an improved version of the Hata model. It is widely used for predicting path loss
in mobile wireless system.It is designed to be used in the frequency band from 1500 MHz to 2000 MHz. It
also includes corrections for urban, suburban and rural (flat) environments [13],[14].
( )( ) ( ) ( ) ( ) ( ( )) ( )
(7)
3.4. SUI Model
SUI model comes out with three different types of terrain like terrain A dense urban locality,
terrain B has hilly regions and terrain C for rural with moderate vegetation. The general path loss expression
according to the SUI model is given by [15].
( ) (8)
Parameter is defined as follows
( ) (9)
where is the wavelength in meters. Path loss exponent given by [16].
⁄
The correction factors for the operating frequency and for the receiver antenna height for the model are :
( ) (10)
and, for terrain type
( ) for terrain type A and B (11)
( ) for terrain type A and B (12)
Where f, is the frequency in MHz, and is the receiver antenna height in meters. The SUI model is used
for path loss prediction in rural, suburban and urban environments.
4. MEASUREMENT PROCEDURE AND METHOD OF ANALYSIS
A drive-test system was used to collect and record signal levels at various locations in a form of logs
which were later processed with a communication network analyzer (CNA). During a drive-test some of the
system parameters that may be collected are: pilot power strength Ec/Io, forward transmit power Tx, down-
link transmit Rx and Frame Error Rate FER. Such a test can be conducted for some identified Base Stations
or for the whole network. The drive system measurement tools used were: a Special Mobile Phone (Huawei
U6100) GPS receiver (NMEA), a receiving antenna, and a laptop with a key and a drive test software
(Huawei GENEX Probe). The vehicle was driven within the base station coverage area while continuously
recording the received signal. At every moment of the collected measurements, GPS data is also recorded
simultaneously.The emission sites specifications of these bases and their positions are shown in Table 1.

 ISSN: 2088-8708
2128
Table1. BTS parameters
Parameters BTS1 BTS2
Region type Suburbain Rural
Transmit power (dBm) 46 43
Cable Loss + Body loss 10.5 9.7
Transmitting antenna gain (dBi) 17.5 16.7
Receive antenna gain (dBi) 0 0
Transmit antenna height (m) 25 35
Mobile station antenna height (m) 1.5 1.5
Operating frequencies (MHz)
Uplink frequency 908 912,4
Dn-link frequency 953 957,4
Geographic coordinates Latitude 35,2524 35,62437
Longitude 6,13074 6,36984
5. RESULTS AND DISCUSSION
5.1. Comparison with prediction models
a comparison between predicted path loss and measured path loss have been performed for two base
stations BTS1 and BTS2. The performance of the empirical models is then compared to the measured path
loss data as in Figures 1 and 2. The values of Mean Error-ME , Root Mean Square Error-RMSE,Standard
deviation of error-STD and Relative Error Percentage, are used to measure the forecasting accuracy of these
models, are tabulated in Table 2 and Table 3.
Figure 1. Comparison between predicted and
measured path loss for BTS1
Figure 2. Comparison between predicted and
measured path loss for BTS2
From Table 2 and Table 3, it is found that performance of the COST231 Hata model is the best as
RMSE and ME are the lowest compared to other models. Figure 1 and Figure 2 consolidate the result that
COST231 Hata model is closet to measured path loss than other models.
Table 2. Performance comparison between models used according to test criteria(BTS1)
HATA R
Cost 231
SUI C
EGLI
rmse Me std re
29.0112
13.8847
39.4771
33.2731
26.4328
8.9197
36.4740
30.1805
0.1452
0.1462
0.1427
0.1439
20.4598
6.9615
28.2178
23.3654
0 0.5 1 1.5 2 2.5
20
40
60
80
100
120
140
Distance (Km)
PathLoss(db)
Empirical Models In suburban area
Cost231
Hata Sub
unfiltered measurements
SUI type B
Egli
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
20
40
60
80
100
120
140
160
180
Distance (Km)
PathLoss(db)
Empirical Models In Rural Area
Cost231
Hata Rural
unfiltered measurements
SUI type C
Egli

IJECE ISSN: 2088-8708 
2129
Table 3. Performance comparison between models used according to test criteria(BTS2)
Cost 231
HATA R
EGLI
SUI C
rmse Me std re
26 .946
27.5175
33 .5499
51.1802
26.366
26.949
32.582
50.6988
0.5886
0.6084
0.5712
0.5589
20.1549
20.1809
24.9922
38.6516
5.2. Optimization Process by PSO alghorithm
The COST 231 model is chosen for this study. Formulating the problem to be solved as a single
mathematical Equation has five variables as shown in Table 4, assessed by a cost function to a stopping
criteria depends on the performance thereof. And this cost function is generally defined as the RMSE (Root
Mean Square Error).
COST 231(rural/sub) model is defined as
( ) ( ) ( ) ( ( )) ( )
(13)
( ) ( ( ) ) ( ( ) )
It can be written as follows
( ) ( ) ( ) ( ) ( )
( ) (14)
Table 4. The optimized parameters
K1=46.3 K2=44.9 K3=-13.82 K4=-6.55 K5=33.9
The fitness function used for parameters adjustment is defined by the mean square error (RMSE) as:
√
∑
Where represents the measured path loss in dB, is the predicted path loss in dB, and is the number
of the measured data points.
5.2.1. Optimization results by PSO
Simulation results using the PSO Alghorithm are presented in the following Figure 3, Figure 4,
Table 5 and Table 6.
Figure 3. Comparison between COST-231 Hata and COST231-Opt (suburban)
0 0.2 0.4 0.6 0.8 1 1.2 1.4
70
80
90
100
110
120
130
140
Distance in Km
PathLossindb
Empirical Models parametres tuning using pso algorithme
Cost231
data
cost 231 Optimized withe pso

 ISSN: 2088-8708
2130
Figure 4. Comparison between COST-231 Hata and COST231-Opt (rural)
Table 5. Results of the optimization process for COST-231Hata model (suburban)
Cost231-opt Cost231
Parametres K1 27 .1267 46 .3
K2 14.5035 33.9
K3 19.6153 13.82
K4 -6.9221 44.9
K5 25.5010 6.55
RMSE 0.7688 16.1158
Time of calculation (s) 10.1830 /
Table 6. Results of the optimization process for COST-231Hata model (rural).
Cost231-opt Cost231
Parametres K1 25.9280 46 .3
K2 5.7622 33.9
K3 26.5562 13.82
K4 10.3980 44.9
K5 27.4992 6.55
RMSE 1.1172 27.2553
Time of calculation (s) 9.1150 /
Beginning with the results of Table 5 and Table 6 and passing through the two Figures 3 and 4, we
have noticed that both optimized models in rural and suburban area surpass other models in terms of overall
performance.
6. CONCLUSION
In this paper, the measured path losses in two cells are compared with theoretical path loss
models: Hata, SUI, Lee and Egli. Based on this, an optimized COST-231 Hata model for the prediction of
path loss in Rural and Suburban environments of Batna city (Algeria) is developed. From the numerical
example, a new values of parameters are proposed for COST-231 Hata model based on measured data. It is
obvious that adjusted COST-231 Hata model shows the closest agreement with the measurement result.
Hence COST-231 Hata model with proposed modification is recommended for rural and suburban area of
Batna city.
REFERENCES
[1] Torres J, Guardado J.L , Rivas-Dávalos F, Maximov S, Melgoza E, “A Genetic Algorithm Based on the Edge
Window Decoder Technique To Optimize Power Distribution Systems Reconﬁguration”, Electrical Power and
Energy Systems, vol. 45, pp.28–34, 2013.
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
50
60
70
80
90
100
110
120
130
140
Distance in Km
PathLossindb
Empirical Models parametres tuning using pso algorithme
Cost231
data
cost 231 Optimized withe pso

IJECE ISSN: 2088-8708 
2131
[2] Carreno E., Romero R, Padilha-Feltrin A, “An Efficient Codification to Solve Distribution Network
Reconfiguration for Loss Reduction Proble”, IEEE Trans Power Syst, vol. 3, pp. 42–51, 2008.
[3] Famoriji J, Olasoji Y, “Radio Frequency Propagation Mechanisms and Empirical Models for Hilly Areas”,
International Journal of Electrical and Computer Engineering (IJECE) vol. 3, pp. 372-3763, 2013.
[4] Imran I, Mustafa S, Mahmood AK, Shahzad A. Malik, Shahid A, “Path Loss Modeling of WLAN and WiMAX
System”, International Journal of Electrical and Computer Engineering (IJECE),vol .5, pp. 1083-1091, 2015.
[5] M.Garah et al, "Path Loss Models Optimization for Mobile Communication in Different Areas" , Indonesian
Journal of Electrical Engineering and Computer Science,vol.3, pp.126-135, july2016.
[6] Tahcfulloh S, Riskayadi E, “Optimized Suitable Propagation Model for GSM 900 Path Loss
Prediction”,TELKOMNIKA Indonesian Journal of Electrical Engineering, vol.14, pp. 154-162, 2015.
[7] Surajudeen Bakinde N, Faruk N, Ayeni A, Muhammad M, Gumel M, “Comparison of Propagation Models for
GSM 1800 and WCDMA Systems in Selected Urban Areas of Nigeria”, International Journal of Applied
Information Systems (IJAIS), Vol. 13, pp. 6-13, 2012.
[8] J. Kennedy, R. Eberhart, “Particle swarm optimization”, Proceedings of the IEEE International Conference on
Neural Networks, (ICNN), vol. 4, pp. 1942–1948, 1995.
[9] Y. Shi, R. Eberhart, “A Modified Particle Swarm Optimizer”, Evolutionary Computation Proceedings, 1998. IEEE
World Congress on Computational Intelligence, IEEE, pp. 69–73, May 1998.
[10] Egli J. J, “Radio Propagation above 40 Mc over Irregular Terrain”, Proc. IRE, vol.45 no10, pp.1383–1391,1957.
[11] Sarkar T. K., et al, “A Survey of Various Propagation Models For Mobile Communication”,IEEE Antennas and
Propagation Magazine, vol.45, pp. 51–82 , 2003.
[12] Hata M, “Empirical Formula for Propagation Loss in Land Mobile Radio Service”, IEEE Trans. Veh. Technol, vol.
29 no 3, pp. 317-325, 1980.
[13] Parsons J. D, “The Mobile Radio Propagation Channel”, 2nd ed,Wiley,West Sussex 2000.
[14] Asztalos T, “Planning a WiMAX Radio Network with A915. Alcatel-Lucent COST Action 231. Digital mobile
radio towards future generation systems”, final report, tech. rep, European Communities, EUR 18957,1999.
[15] H. R. Anderson, “Fixed Broadband Wireless System Design”, John Wiley and Sons Ltd, 2003.
[16] Erceg V., Greenstein L. J, “In Empirically based Path Loss Model for Wireless Channels in Suburban
Environments”, IEEE Journal on Selected Areas of Communications,vol.17, pp. 1205–1211, 1999.

Particle Swarm Optimization for the Path Loss Reduction in Suburban and Rural Area

More Related Content

What's hot (15)

Similar to Particle Swarm Optimization for the Path Loss Reduction in Suburban and Rural Area (20)

More from IJECEIAES (20)

Recently uploaded (20)

Particle Swarm Optimization for the Path Loss Reduction in Suburban and Rural Area