Real Time Microcontroller Based Remote Water Monitoring System in Agriculture

236
Scholars Journal of Engineering and Technology (SJET) ISSN 2321-435X (Online)
Sch. J. Eng. Tech., 2014; 2(2B):236-242 ISSN 2347-9523 (Print)
©Scholars Academic and Scientific Publisher
(An International Publisher for Academic and Scientific Resources)
www.saspublisher.com
Research Article
Real Time Microcontroller Based Remote Water Monitoring System in
Agriculture
Abhirup Patra1, Subhadeep Chakraborty*2
1
M.Tech Student, Department of Electronics and Communication Engineering, MCKV Institute of Engineering, West
Bengal, India.
2
Assistant Professor, Department of Electronics and Communication Engineering , Calcutta Institute of Technology,
West Bengal, India.
*Corresponding author
Subhadeep Chakraborty
Email: jsint.eng.prs@gmail.com
Abstract: In the present world, the application of remote monitoring can be found everywhere. Actually it reduces the
human labor and enhances the field where it is applied. In recent days, the agriculture system is so advanced and fast that
it requires the automatic system for the control over the agriculture field. Watering the farming land is one of the most
important operations in the agriculture. Manual operation for watering may cause a wrong measurement of amount of
water supply. So, to supply the water in a correct and prescribed amount regarding to how much water is available in the
soil, the automation is required. The system described in this paper is incorporated with the ability of determining the
amount of water in soil and depending upon the amount it will supply water into the farming land if it down to the lower
limit and stop the supply when it crosses its highest limit as predefined by preset value. The system can be operated both
in automatic and manual mode so that the super control can be obtained from this system to the farmers. Through the
system, the watering of the farming land can be controlled from a remote place without going to the site.
Keywords: Real Time system, Water monitoring, Microcontroller, Sensor, Agriculture.
INTRODUCTION
In agriculture, one of the most important job is
to watering the farming land. Most of the farmers use
the manual control over the land that is to monitor the
pumping or watering the land by visiting the site. This
will surely need more and more labor and as a result the
efficiency of work may be degraded. An automatic
system can be developed to monitor all the controlling
operation. Automatic control system reduces the human
labor and increase the efficiency of the corresponding
work. In this paper, an automatic control system is
introduced for watering the land by measuring the
humidity or in other word the temperature. The system
measures the humidity of the soil and depending upon
the condition it will provide the needed water in the
land [1-2].
There are a number of systems introduced to
enhance the agriculture system by providing it with
various autonomous control systems. The agriculture
technique has been developed day by day all over the
world and so the agriculture engineering has been
enhanced gradually to serve the world with more
integrated and efficient system [1-4,7].
The system prescribed here is simulated and
installed successfully. It will sense the humidity in a
continuous fashion. There is a sensor included in this
system which senses the humidity and sends the record
to the Microcontroller [1-2, 4, 6, 8]. The pumps are
connected with the system via relay circuit. There are
two conditions are set in between which the pump will
be ON or OFF. When the water supply is needed,
Microcontroller sends an analog pulse to the system to
enable the relay circuit and the water will be supplied
till the time the pump will be ON[1-2, 4].
So, in this system no manual labor is there to
control the overall process. The detailed operation of
the system will be discussed in the next section along
with the system components and the algorithm.
REAL TIME MONITORING SYSTEM
The real time monitoring system means the
system that will control some operation will be
implemented in a hardware fashion. Real time water
monitoring system is based on microcontroller
environment and sensed by humidity sensor. The
essential components and the operation of the system is
described in this section [2-4,6-7,13].

Chakraborty S et al., Sch. J. Eng. Tech., 2014; 2(2B):236-242
237
Components
The main components are stated and described below:
i) Microcontroller
This is the main component which makes
control over the system. The main operation of the
Microcontroller is to receive the pulse from the
humidity sensor and sends the required direction to the
relay system for pumping operation to be started
[1,3,4,7].
ii) Capacitive Humidity Sensor
It senses the humidity of the soil continuously.
The sensed condition is given as the input to the
microcontroller will give the signal to relay using
RS232 serial communication protocol which drives the
water pump. If the sensed range is true for pumping, the
system will supply water in the agriculture ground [4,6-
9].
iii) Analog to Digital Converter
The humidity sensor sends the analog pulse to
the system. But to read the condition, Microcontroller
needs an Analog to Digital Converter. MCP3202 IC is
used in this system to obtain the digital format of the
condition that is checked by the sensor. MCP3202 is a
successive approximation 12-bit Analog-to-Digital
(A/D) Converter with on-board sample and hold
circuitry. The MCP3202 is programmable to provide a
single pseudo-differential input pair or dual single-
ended inputs. Differential Nonlinearity (DNL) is
specified at ±1LSB, and Integral Nonlinearity (INL) is
offered in ±1LSB (MCP3202-B) and ±2LSB
(MCP3202-C) versions. The MCP3202 device operates
over a broad voltage range (2.7V-5.5V). The device is
capable of conversion rates of up to 100ksps at 5V and
50ksps at 2.7V [1, 4, 7-9, 11-12].
Operation
The overall objective of the system is to
indicate the status of humidity of the soil and to
automatically control the water supply to the land in
order to prevent the dry condition for the soil. The
sensed condition is given as the input to the
microcontroller through Analog to Digital Converter
and based on the condition the microcontroller will give
the signal to relay which drives the water pump for
watering. The system incorporates with a LCD screen
which displays the condition of the soil.
The water of the soil of the land, when
evaporated, the land gets dried up. The prescribed
system can identify the water availability condition of
the soil and to automatically control the water supply to
the land from a remote place to prevent it to be dried
up.
In this automatic system, embedded
technology is used in order to achieve the good profit in
the agricultural field the soil should be maintained in
proper condition that fits for the crop cultivation. The
main thing that should be seen in order to achieve the
profit is to maintain the wet condition of the soil in the
correct proportion.
The sensor is placed in the soil and it reads
continuously the levels of the moisture or amount of
water available in the soil. There a prescribed range is
preset in between which the sensor gets an ignition for
its operation. When it reads the lower level of the
humidity or more specifically the relative humidity
(RH), it sends a pulse to the ADC informing that the
level of the amount of the water in the soil goes to
minimum and this analog signal is then converted to its
corresponding digital format and get routed by the
modem MAX232 IC to the Microcontroller. After
receiving the signal, controller will send the signal to
the relay section and make it turn ON. When the relay is
turned ON, the pump will be activated and it supplies
the water to the land. There is a remote controlling unit
is placed in between the main controlling section and
the sensor which again is controlled by the
microcomputer unit. In the mean time, the sensor
continues its reading the humidity and until it reaches to
its maximum value of operation. While reading, the
sensor continuously supply the information to the
controller and controller will make switch ON the pump
and the water will be supplied continuously. Now, when
the sensor reads the maximum humidity of the soil, it
again sends that information to the Microcontroller and
controller immediately switch OFF the pump and the
water supply will be turned off accordingly. The
capacity of the water flow will be suitably designed by
means of resizing the radius of the water supply pipe.
The entire circuit is interconnected with RS232
cable and the power supply that is needed to run the
system is 5 volt. So, in this system, the agriculture
ground can be monitored from a remote place without
going there and the soil water level can be maintained
accordingly [1, 3, 6, 13].
HUMIDITY MEASUREMENT
Water supply is required in the agriculture
ground when the soil contains lesser amount of water.
When the temperature in the air increases, the capability
of air for holding the water vapor will be increased.
This means the temperature rise in air causes more
vaporization in the air from soil. So, it is obvious the
amount of water in the soil will be decreased [1, 2, 4, 7,
9]. The humidity sensor senses the amount of the water
particle or humidity of the soil. The humidity sensor,
mentioned above, is actually senses the present
humidity i.e. the Relative Humidity (RH). The relative
humidity is actually the ratio of actual vapor present to
the saturation vapor amount and can be represented by
the equation mentioned below [2, 4, 8-10, 12].

238
 
Actual Vapor Dendity
Relative Humidity= 100% ... 1
Saturation Vapor Density

So, the vaporization or in other word the
relative humidity is inversely proportional to the
temperature rise of the air as well as the actual humidity
of the air as because the actual humidity is directly
proportional to the temperature rise. These are
illustrated in the following equations [2, 4, 8-10],
 
 
 
Actual Humidity Temperature Rise ... 2
1
Relative Humidity ... 3
Temperature Rise
1
Relative Humidity ... 4
Actual Humidity



There are two fixed values of humidity sensor,
monitored by the controller, which totally control the
supply and flow of the water into the agriculture
ground. When RH is low, it indicates high temperature
and so the vaporization into the air will be increased [2,
5,6, 9, 10, 13]. Then the relay will be turned ON and the
water will be supplied into the ground. While supplying
the water into the ground, the amount of water will be
increased in the agriculture ground meaning that the
humidity in the soil will be in increasing mode. In the
highest preset value of the sensor, it indicates the lower
temperature or in the other hand the vaporization is low
as the amount of the water in the soil is in the highest
level. Then the relay will be turned OFF and the water
supply in the soil will be halted. After some time when
the vaporization is increasing, the system will iterate in
the same way and then it continues the water supply.
Thus, this system, by sensing the relative
humidity, will work without interruption and efficiently.
As the sensor in the ground is connected with the
central through the cable, it can be efficiently monitored
from the remote place.
BLOCK DIAGRAM
The block diagram of the system including the
main controlling unit, remote controlling unit and the
sensor part is shown in Fig.1
Fig. 1 Block diagram
In this block diagram, there are mainly three
working blocks and they are:
1. Main Control Unit (MCU)
2. Remote Control Unit (RCU)
3. Sensor Unit (SU)
In the MCU, there are microcontrollers, LCD
driver, motor driver, cable driver and the command key
are internally connected. The signal coming from RCU
is received by the cable driver through RS232 cable and
sent to the Microcontroller. The humidity is displayed
in the LCD screen and with the command by the
Microcontroller the motor driver is enabled. The
Command key is one of the important parts of the
system. The total system can be operated automatically
or manually. Among the four keys, one is used for
automatic operation and rests three are for manual
operation. That means when agriculture process is
going on, the automatic mode is suitable for that
purpose but for when it is not needed i.e. water need not
to be supplied to the ground, the manual mode is
suitable as one of the mentioned three keys is the STOP
key to stop the entire operation.
In the RCU, the controller, ADC and the
Sensor driver are internally connected. The humidity
sensed by the sensor, is received by the sensor driver
and converted to its digital format by the ADC and
sends it to the controller. The controller sends the
digital data to the MCU.

239
ALGORITHM FOR REMOTE SOIL
MONITORING
Remote soil monitoring system works on the
principle of checking the amount of water in the soil
and thereby activating the pump when required. The
work flow of the system is represented in Remote
Sensed Monitoring (RSM) algorithm.
Pseudo code:
Select mode  M : 1M or 2M ;
if M== 1M ;
Switch 1K ;
1K ==”1”;
do
Check water amount in soil ( soilW );
Display soilW ;
Check the preset values: least highestP ,P ;
for soilW == leastP ;
mS == "1"// mS =Status of motor driver
until
soilW == highestP ;
if soil least soil highestW P && W P  ;
Check continuously;
Control the flow;
if soilW == highestP ;
mS == "0";
repeat;
else
do
Check soil least highestW ,P ,P ;
switch 2K ;
Display soilW ;
for soilW == leastP ;
switch 2K ;
3K ==”1”;
mS == “1”;
until
soilW == highestP ;
if soil least soil highestW P && W P  ;
3K ==”1”;
mS == “1”;
Check continuously;
Control the flow;
if soilW == highestP ;
switch 4K ;
4K == “0”;
mS == “0”;
repeat;
Through the RSM algorithm, the system can
be monitored automatically or manually both when
needed.
OPERATIONAL FLOW CHART
The pseudo code describe in the above section
is represented in a flow chart form in this section. Flow
chart is helpful in implementing the actual system. In
this flow chart, the operation and the mode selection
along with the pump operation and the relay operation
is completely described.
In Automatic mode of operation, only one key
is required to be pressed for activation and then the
mode will work according to the direction given to it. If
the automatic mode faults in some critical condition, the
manual operation will be in operation. So, in this
system, there is a lesser chance to get a fault for
operation and hence can be operated efficiently.
The flow chart is constructed in E-draw v6.8
where a number of process box, control box and all the
other boxes that are mainly required for constructing the
flow chart are readily available. The flow chart is
shown in Fig.2.
In this flow chart, the switching and control
operations are described clearly so that a system can be
constructed easily. The main advantage of the design
the flow chart in E-draw is that the flow chart is much
more clear and significant than any other drawing tools
and it produces the output with a lesser size so that it
can be fit in the required space and have no problem
with the fitness.

240
Fig.2 Flow chart of RSM Algorithm
SYSTEM HARDWARE
The system hardware that is the main system
PCB includes several parts or blocks such as the
Display section, Transformer section, Relay section,
Sensor section etc. Those sections are given below.
Fig. 3 Transformer Section
Fig. 4 Keyboard Section
Fig. 5 Sensor Section
Fig. 6 Remote Controlling Section

241
Fig. 7 Display Section
Fig. 8 Relay Section
Fig. 9 Complete System Circuit
SOFTWARE ENVIRONMENT
Any circuit is needed to design in the software
first to check the response of the generated system. The
system is first designed in Proteus 7 and the assembly
code that is required for simulation of the circuit, is
written in Keil C or in other word Embedded C. The
HEX code generated by the Keil C is given as the input
to the Microcontroller in the Proteus circuit and it gives
the desired result as mentioned above.
The system is actually an embedded system
meaning the whole system is run by a single source of
voltage from the transformer. So the system design and
the code writing will be must in the embedded
environment only to simulate it properly.
OUTPUT RESULT OF SYSTEM
The system checks the status of the water in
the soil and display it on the LCD device and based on
the true condition, it stats the relay as well as the pump
to supply water. The output condition of the system is
depicted below.
When the RH of the soil is below the preset
value it will activate the motor as well as the pump and
display the RH on the LCD along with the information
that the pump or the motor is ON.
Fig. 10 LCD Displays the lowest preset value of RH
Fig. 11 Motor turned ON for lowest preset value of
RH
Now the sensor will check for the range of the
lowest and highest preset values of the RH and go
further for highest value. Meanwhile it continues the
activation of the motor. So in between the lowest and
the highest value of RH, the motor is enabled and
continues the supply of the water. When the RH value
reaches the highest condition, it will automatically turn
OFF the motor and the water supply will be terminated.

242
Fig. 12 System checks for the highest preset value of
RH
Fig. 13 Motor is turned OFF for highest preset value
of RH
FUTURE SCOPE
In the recent days the agriculture is very much
developing and so the farmers also need some special
feature of the systems that are currently used for it.
Automatic pumping system is one of the useful systems
in the agriculture. It will supply water just when it is
needed. So, one part of labor can be operated by the
machine itself and so the efficiency of the farming will
be increasing and as the system is dependent on the RH
value of the soil, so there no overflow or underflow of
water in the agriculture ground.
The system can also be used apart from the
agriculture. The remote sensing has a broad application
in the world. Each and everywhere the remote sensing
operation can be found. In aerospace, for signalling for
advert weather or in some critical condition, it can be
used for automatic operation. For traffic system, the
RSM algorithm can work efficiently. This system can
be applicable for in-house maintain system also i.e. for
in-house monitoring of different electrical or electronics
parts i.e. Fan, Light etc. The moisture level can also be
detected of an particular remote area apart from the soil
testing and can be indicated by the display so that one
can aware of the local moisture level as well as the
relative humidity an also the dew point.
CONCLUSION
In conclusion, it can be said that the system
reduces the human labor in agricultural field and
enhance the production by supplying the water into the
ground. The system can be enhanced to create a
complete monitoring of the agriculture ground by
supplying different materials such as the fertilizers into
the ground and thus by reducing more and more human
efforts for cultivation.
REFERANCE
1. Yi Qi, Philip E; Dennison JS, David R; Monitoring
live fuel moisture using soil moisture and remote
sensing proxies. Fire Ecology , 2012; 8(3):71-87.
2. David LB, Tian G, Tim R, McVicar, Qin Yi, Li
F; Soil Moisture and Drought Monitoring Using
Remote Sensing, Final Report Australia-China
Joint Science and Technology Commission Project.
1992-1997. CSIRO Australia.
3. Jirapon S, Chaiwat O; Real-time flood monitoring
and warning system. Songklanakarin J. Sci.
Technol, 2011; 33 (2):227-235.
4. Edward MB, Kenneth AS, John WH, Scott ML,
Dennis LC, Yang C, Craig ST, Walter CB;
Remote- and Ground-Based Sensor Techniques to
Map Soil Properties. Photogrammetric Engineering
& Remote Sensing, 2003; 69(6): 619–630.
5. Jerry CR, Paul VZ, James HE; Remote Sensing
Techniques to Assess Water Quality.
Photogrammetric Engineering & Remote Sensing,
2003; 69(6): 695–704
6. Manchanda ML, Kudrat M, Tiwari AK; Soil survey
and mapping using remote sensing. Tropical
Ecology, 2002; 43(1): 61-74.
7. Morris M; Soil Moisture Monitoring: Low-Cost
Tools and Methods. NCAT Energy, 2006; 1-12.
8. Swarup SM, Chaudhari DS; A Review on Smart
Sensors Based Monitoring System for Agriculture.
International Journal of Innovative Technology and
Exploring Engineering, 2013; 2(4):76-78.
9. Grahn H; Remote Monitoring of Soil Moisture.
Southwest Hydrology, 2003.
10. Garcia L, Eldeiry A, Elhaddad A; Estimating soil
salinity using remote sensing data. Civil
Engineering, 2000; 1-10.
11. Anderson WB, Zaitchik BF, Hain CR, Anderson
MC, Yilmaz MT, Mecikalski J, Schultz L;
Towards an integrated soil moisture drought
monitor for East Africa. Hydrol. Earth Syst. Sci.
Discuss., 2012; 9:4587–4631.
12. Wang L, John JQU; Satellite remote sensing
applications for surface soil moisture monitoring:
A review. Front. Earth Sci. China, 2009; 3(2):
237–247.
13. Dinesh M, Saravanan P; FPGA Based Real Time
Monitoring System for Agricultural Field.
International Journal of Electronics and Computer
Science Engineering, 2013;1(3):1514-1519.

Real Time Microcontroller Based Remote Water Monitoring System in Agriculture

More Related Content

What's hot (20)

Similar to Real Time Microcontroller Based Remote Water Monitoring System in Agriculture (20)

More from Subhadeep Chakraborty (10)

Recently uploaded (20)

Real Time Microcontroller Based Remote Water Monitoring System in Agriculture