RGPV NOTES ON FACTS EX8303 unit I & II

1
Prof MD Dutt HOD Ex Department SRCT ThuakhedaBhopal MP India
READING MATERIAL FOR B.E. STUDENTS
OF RGPV AFFILIATED ENGINEERING COLLEGES
BRANCH VIII SEM ELECTRICALAND ELECTRONICS
SUBJECT FACTS
Professor MD Dutt
Addl GeneralManager(Retd)
BHARAT HEAVY ELECTRICALS LIMITED
Professor(Ex) in EX Department
Bansal Institute of Science and Technology
Kokta Anand Nagar BHOPAL
Presently Head of The Department ( EX)
Shri Ram College OfTechnology
Thuakheda BHOPAL
Sub Code EX 8303 Subject FACTS
UNIT I & II Basic issues, FACT Controllers
Static VAR Compensator (SVC)

2
EX 8303
UNIT I FACT RG PV Syllabus
Basic issues involve in bulk power transmission , Review of basics of power
transmission networks, Control of power flow in AC transmission line, Analysis of
uncompensated AC transmission line, Passive reactive power compensation, Principle
of transmission system compensation , Need for FACT controllers – types FACT
controllers and benefits.
UNIT II FACT RG PV Syllabus
Voltage controlby SVC- advantages of slope in dynamic characteristics, Influence of
SVC on system voltage, Design of SVC voltage regulator Modeling of SVC for power
flow and stability studies Application – enhancement of transient stability Steady state
power transfer, enhancement of power system damping, provision of voltage instability
INDEX
S No Topic UNIT I Page
1 Basic Issues involve in bulk power transmission 3- 4
2 Review of basics of power transmission network 4-6
3 Control of power transmission in AC transmission line 6-8
4 Analysis of uncompensated transmission line 8-12
5 Passive reactive power compensation 13-16
6 Principle of transmission system compensation 16-17
7 Need for FACT controllers – types fact controllers and benefits 18
S No Topic UNIT II Page
8 Voltage controlby SVC- advantages of slope in dynamic
characteristics
19-21
9 Influence of SVC on system voltage 21-23
10 Design of SVC voltage regulator 23-31
11 Modeling of SVC for power flow and stability studies 32-34
12 Application – enhancement of transient stability 35-36
13 Steady state power transfer, enhancement of power system
damping, provision of voltage instability
37-41

3
1. BASIC ISSUES INVOLVE IN BULK POWER TRABSMISSION
The increasing Industrialization, urbanization of life style has lead to increasing
dependency on the electrical energy. This has resulted into rapid growth of PSs. This
rapid growth has resulted into few uncertainties. Power disruptions and individual
power outages are one of the major problems and affect the economy of any country. In
contrast to the rapid changes in technologies and the power required by these
technologies, transmission systems are being pushed to operate closer to their stability
limits and at the same time reaching their thermal limits due to the fact that the delivery
of power have been increasing. The major problems faced by power industries in
establishing the match between supply and demand are:
1.Transmission & Distribution; supply the electric demand without exceeding the
thermal limit.
2.In large PS, stability problems causing power disruptions and blackouts leading
to huge losses.
These constraints affect the quality of power delivered. However, these constraints can
be suppressed by enhancing the PS control. One of the best methods for reducing these
constraints is FACTS devices. With the rapid development of power electronics,
FACTS devices have been proposed and implemented in PSs. FACTS devices can be
utilized to control power flow and enhance system stability. Particularly with the
deregulation of the electricity market, there is an increasing interest in using FACTS
devices in the operation and control of PSs. A better utilization of the existing PSs to
increase their capacities and controllability by installing FACTS devices becomes
imperative. FACTS devices are cost effective alternatives to new transmission line
construction. Due to the present situation, there are two main aspects that should be
considered in using FACTS devices: The first aspect is the flexible power system
operation according to the power flow control capability of FACTS devices. The other
aspect is the improvement of transient and Steady State Voltage Stability of PSs.
FACTS devices are the right equipment to meet these challenges.
Definition of FACTS
According to IEEE, FACTS, which is the abbreviation of Flexible AC
Transmission Systems, is defined as follows:
“Alternating currenttransmission systemsincorporatingpower electronics based and
other static controllers to enhance controllability and APTC”.
Since the ʺother static controllersʺ based FACTS devices are not widely used in
current PSs, the focused only on the power electronics based FACTS devices.
The FACTS controllers are classified as follows:

4
 Thyristor controlled based FACTS controllers such as TSC, TCR, FC‐TCR,
SVC, TCSC, TC‐ PAR etc. 

 VSI based FACTS controllers such as SSSC, STATCOM, UPFC, GUPFC,
IPFC, GIPFC, HPFC etc. 
2. Review of Basics of Power Transmission Networks
A large majority of power transmission lines are AC lines operating at different
voltages (10 kV to 800 kV). The distribution networks generally operate below 100 kV
while the bulk power is transmitted at higher voltages. The lines operating at deferent
voltages are connected through transformers which operate at high efficiency.
Traditionally, AC lines have no provision for the controlof power flow. The
mechanically operated circuit breakers (CB) are meant for protection against faults
(caused by flashovers due to Over voltages on the lines or reduced clearances to
ground). A CB is rated for a limited number of open and close operations at a time and
cannot be used for power flow control. (unlike a high power electronic switch such as
thyristor, GTO, IGBT, IGCT, etc.). Fortunately, ac lines have inherent power flow
control as the power flow is determined by the power at the sending end or receiving
end. For example, considera transmission line connecting a generating station to a load
centre in Fig.1.1(a). Assuming the line to be lossless and ignoring the line charging, the
power flow (P) is given by
P = V1 V2 Sin(θ1-θ2) 1.1
X
where X is the series line reactance. Assuming V1 and V2 to be held constants (through
voltage regulators at the two ends), the power injected by the power station determines
the flow of power in the line. The difference in the bus angles is automatically adjusted
to enable P = PG (Note that usually there Could be more than one line transmitting
power from a generating station to a load centre). If one or more lines trip, the output of
the power station may have to be reduced by tripping generators, so as to avoid
overloading the remaining lines in operation.
Fig 1.1

5
Fig. 1.1(b) shows another situation where a line supplies power to a load located at bus
(2). Here also the eq. (1.1) applies but the power flow in the line is determined by the
load supplied. The essential difference between the two situations is that in Fig. 1.1(a),
the load centre is modeled as an infinite bus which can absorb (theoretically) any
amount of power supplied to it from the generating station. This model of the load
centre assumes that the generation available at the load centre is much higher than the
power supplied from the remote power station (obviously, the total load supplied at the
load centre is equal to the net generation available at that bus).
FIG 1.2
The reliability of the power supply at a load bus can be improved by arranging two (or
more) sources of power as shown in Fig. 1.2. Here, P1 is the output of G1 while P2 is
the output of G2 (Note that we are neglecting losses as before). However, the tripping
of any one line will reduce the availability of power at the load bus. This problem can
be overcome by providing a line (shown dotted in Fig. 1.2) to interconnect the two
power stations. Note that this results in the creation of a mesh in the transmission
network. This improves the system reliability, as tripping of any one line does not result
in curtailment of the load. However, in steady state, P1 can be higher or lower than PG1
(the output of G1). The actual power flows in the 3 lines forming a mesh are determined
by Kirchhoff’s Voltage Law (KVL). In general, the addition of an (interconnecting) line
can result in increase of power flow in a line (while decreasing the power flow in some
other line). This is an interesting feature of AC transmission lines and not usually well
understood (in the context of restructuring). In general, it can be stated that in an
uncontrolled AC transmission network with loops (to improve system reliability), the
power flows in individual lines are determined by KVL and do not follow the
requirements of the contracts (between energy producers and customers). In other
words, it is almost impossible to ensure that the power flow between two nodes follows
a predetermined path. This is only feasible in radial networks (with no loops), but the
reliability is adversely affected as even a single outage can result in load curtailment.
Consider two power systems, each with a single power station meeting its own local
load, interconnected by a tie line as shown in Fig. 1.3(a). In this case, the power flow in
the tie line (P) in steady state is determined by the mismatch between the generation
and load in the individual areas. Under dynamic conditions, this power flow is
determined from the equivalent circuit shown in Fig. 1.3(b). If the capacity of the tie is
small compared to the size (generation) of the two areas, the angles ±1 and ±2 are not
affected much by the tie line power flow. Thus, power flow in AC tie is generally
uncontrolled and it becomes essential to trip the tie during a disturbance, either to
protect the tie line or preserve system security. In comparison with a AC transmission

6
line, the power flow in a HVDC line in controlled and regulated. However, HVDC
converter stations are expensive and HVDC option is used primarily for (a) long
distance bulk power transmission (b) interconnection of asynchronous systems and (c)
underwater (submarine) transmission. The application of HVDC transmission
(using thyristor converters) is also constrained by the problem of commutation failures
affecting operation of multi terminal or multi-feed HVDC systems. This implies that
HVDC links are primarily used for point-to-point transmission of power and
asynchronous interconnection (using Back to Back (BTB) links).
(a) Single line diagram
(b)Equivalent circuit
Fig 1.3 Two areas connected by a tie line
3. Control of Power Flow in AC Transmission Line
We may like to control the power flow in a AC transmission line to (a) enhance power
transfer capacity and or (b) to change power flow under dynamic conditions (subjected
to disturbances such as sudden increase in load, line trip or generator outage) to ensure
system stability and security. The stability can be affected by growing low frequency,
power oscillations (due to generator rotor swings), loss of synchronism and voltage
collapse caused by major disturbances.
From eq. (1.1), we have the maximum power (Pmax)transmitted over a line as
Pmax= V1 V2 Sinδmax (1.2)
X

7
where δmax (30º-40º) is selected depending on the stability margins and the stiffness of
the terminal buses to which the line is connected. For line lengths exceeding a limit,
Pmax is less than the thermal limit on the power transfer determined by the current
carrying capacity of the conductors (Note this is also a function of the ambient
temperature). As the line length increases, X increases in a linear fashion and Pmax
reduces as shown in Fig. 1.4.
Fig 1.4 Power transfer capacity as a function of line length
The series compensation using series connected capacitors increases Pmax as the
compensated value of the series reactance (Xc) is given by
Xc = X(1 - kse) (1.3)
where kse is the degree of series compensation. The maximum value of kse that can be
used depends on several factors including the resistance of the conductors.Typically
kse does not exceed 0.7. Fixed series capacitors have been used since a long time for
increasing power transfer in long lines. They are also most economical solutions for this
purpose. However, the controlof series compensation using thyristor switches has been
introduced only 10 to15 years ago for fast power flow control. The use of Thyristor
Controlled Reactors (TCR)in parallel with fixed capacitors for the control of Xc, also
helps in overcoming a major problem of Sub synchronous Resonance (SSR)that causes
instability of torsional modes when series compensated lines are used to transmit power
from turbo generators in steam power stations. In tie lines of short lengths, the power
flow can be controlled by introducing Phase Shifting Transformer (PST) which has a
complex turns ratio with magnitude of unity. The power flow in a lossless transmission
line with an ideal PST (see Fig. 1.5) is given by
P = V1 V2 Sin ( θ ± Φ) (1.4)
X
where θ = θ1-θ2
Fig 1.5 A lossless line with an ideal PST

8
Again, manually controlled PST is not fast enough under dynamic conditions. Thyristor
switches can ensure fast controlover discrete (or continuous) values of Á, depending on
the configuration of PST used. Pmax can also be increased by controlling (regulating)
the receiving end voltage of the AC line. When a generator supplies a unity power
factor load (see Fig. 1.1(b)), the maximum power occurs when the load resistance is
equal to the line reactance. It is to be noted that V2 varies with the load and can be
expressed as
V2 =V1cos (θ1-θ2) (1.5)
Substituting (1.5) in (1.1) gives
P = V1² sin[2(θ1-θ2)] (1.6)
2X
By providing dynamic reactive power supportat bus (2) as shown in Fig. (1.6), it is
possible to regulate the bus voltage magnitude. The reactive power (QC) that has to be
injected is given by
QC = V2² - V1V2 cos(θ1-θ2) (1.7)
X
Fig 1.6 Transmission line compensated by controllable reactive power sourceat
receiving end
Comparing eq. (1.6) with (1.1), it can be seen that the maximum power transfer can be
doubled just by providing dynamic reactive power supportat the receiving end of the
transmission line. This is in addition to the voltage supportat the sending end. It is to be
noted that while steady state voltage supportcan be provided by mechanically switched
capacitors, the dynamic voltage supportrequires synchronous condenseror a power
electronic controller suchas Static Var Compensator(SVC) or STATIC synchronous
COMpensator(STATCOM).
4. Analysis of Uncompensated AC Line
A transmission line has distributed circuit parameters. We will be assuming
the line to be symmetric in three phases and operating with balanced
(positive sequence) voltages and currents. Hence it is adequate to consider only a
single phase positive sequence equivalent network of the line (see Fig. 1.7).
In Fig. 1.7, it is assumed that the sending end is connected to a generator and the
receiving end is connected to a (unity power factor) load. The line has series resistance

9
r and inductance l, shunt conductance g and capacitance c (all parameters expressed per
unit length).
Transmission Line Equations
It is assumed that in steady state all the voltages and currents in the line are sinusoidal
of frequency (ω rad/sec) and expressed in phasors.
Fig 1.7 A transmission line supplying a unity power factor Load
Considering a small element of the line of length (dx) at a distance x from the receiving
end, (see Fig. 1.8) the following equations apply,
I(x + dx) = I(x) + (ydx)V (x + dx) (1.8)
V (x + dx) = V (x) + (zdx)I(x) (1.9)
where y = g + jb, z = r + jx, b = ωc, x = ωl.
Fig 1.8 Voltage and current variation in along line
It is to be noted that bothV and I are phasors that are functions of
x. From the above equations, we get the following differential equations for
V and I. It is to be noted that both V and I are phasors that are functions of x

10

11

12

13
Performance of uncompensatedlines - summary
Based on the analysis given in this and the previous sections, the following points
emerge
1. The dynamic regulation of voltage at the receiving (load) end of the line by using a
controllable reactive source, improves power transfer and voltage profile along the line.
2. However, even with symmetrical lines (with voltages maintained at both ends), the
power transfer capability is decreased as the line length increases. Assuming that a line
is operated with δmax = 30º, the maximum power transfer reduces below SIL for line
lengths θ > 30º(approximately 500 km long line in systems operating at 50 Hz). 3. The
problems of voltage control and charging reactive power (at no load) become severe as
line length increases. Fora symmetric line, the voltage variation is maximum at the mid
point of the line.
5. PASSIVE REACTIVE POWER COMPENSATION
The transmission line has series inductance which absorbs reactive power
while the shunt capacitance releases (generates reactive power). Forlight
loads, the absorption is less than the generation and voltage in the line tends
to rise. On the other hand, at loads exceeding Surge Impedance Loading
(SIL), the absorption is higher than the generation and the voltage tends to
fall. By connecting series capacitors and shunt inductors in the line, we can
control the reactive power flow in the line to limit the voltage variations and
increase (active) power transfer capability. To study the effects of passive
reactive compensation, we will first consider the distributed compensation
(which is difficult to arrange, but is easier to analyze) before taking up
discrete compensation (which is practical).
Distributed Compensation
Let us consider distributed series compensation (capacitive) whose effect, in
steady state, is to counteract the effect of the distributed series inductance of
the line. Similarly, by providing distributed shunt (inductive) compensation,
the effect of line capacitance is reduced.
The phase constant (β’) of a compensated line is given by
β’ = √ωl’ .ωc’ = √ωl(1-kse)ωc (1-ksh)
= β √(1-kse)ωc (1-ksh) (1.10)
where β is the phase constant of the uncompensated line, kse is the degree
of series compensation and ksh is the degree of shunt compensation. It is

14
assumed that both kse and ksh are less than unity.
The surge impedance (Z’n) of the compensated line is obtained as
Z’n = √ ωl’/ωc’ = Zn √(1-kse)/ (1-ksh) (1.11)
From Eqs. (1.10) and (1.11) we note that the electrical length (θ’) of the
compensated line given by
θ’ = dβ’ = θ √(1-kse) (1-ksh) (1.12)
is reduced by both series and shunt compensation. On the other hand,
Zn is reduced by series compensation (capacitive) and increased by shunt
compensation (inductive).
For a lossless symmetrical line, the power flow in a compensated line
is given by
P’ = V² sinδ ≈ V² sinδ = V² sinδ
Z’n sin θ’ Z’n sin θ’ Zn θ1-kse) (1.13)
for small values θ’
The no load voltage at the mid-point (V’mo ) is given by
V’mo = V
cos θ’/2 (1.14)
The charging reactive power (Q’So) at no load is given by
Q’So = -Q’Ro = - V² tan θ’/2 = V² θ (1-ksh)
Z’n 2Zn (1.15)
From Eqs. (1.13) to (1.15) we can observe that
1. The distributed shunt compensation reduces the no load voltage and charging reactive
power, but has little effect on the maximum power
flow in the line.
2. The distributed series compensation reduces the no load voltage and increases the
power transfer capacity, but less little effect on the no load charging reactive power.
Discrete Passive Compensation
It is not practical to provide distributed compensation. Here, we will consider discrete
series and shunt compensation. Before taking this up, it is instructive to derive an

15
equivalent circuit (in steady state) of the distributed parameter, uncompensated line.
Figure 2.10 shows the equivalent Π circuit of the line.
A = 1 + Y Z
2
= cos θ;
B = Z = jZn sin θ
We can also express Z and Y as
Z = jXn sin θ
θ
Y = j Bn[ tan θ/2]
2 2 θ/2
where Xn = ωld = Znθ the total (nominal) reactance of the line and
Bn = ωcd = θ/Zn is the total (nominal) susceptanceof the line.
For small values of θ; sin θ/θ ≈ 1 and tan θ/2 ≈ θ/2 .
Hence Z ≈ jXn, Y ≈ jBn. With this approximation, this equivalent circuit is called as
the
`nominal' Π circuit of the transmission line.
Note: When we are dealing with single phase equivalent of a balanced
symmetric 3 phase network, the parameters of this circuit are the positive
sequence parameters while the voltages and currents are assumed to contain
only positive sequence components. As a matter of fact, for symmetric
networks with no zero sequence components, the coupled 3 phase network
can be reduced to 3 uncoupled single phase networks. Forexample, from
the simple 3 phase network described by
Va Zs Zm Zm Ia
Vb = Zm Zs Zm Ib
Vc Zm Zm Zs Ic (1.16)

16
the network is decoupled if Ia +Ib +Ic = 0 and is described by the equation
Vα = (Zs - Zm)Iα ; α = a, b or c (1.17)
The positive sequence impedance is (Zs - Zm).
For a lossless transmission line, the shunt susceptanceis capacitive and results in
charging reactive power at no load. The shunt reactors at both ends of the line can be
used to fully or partially compensate for this reactive power. With full shunt
compensation (by reactors), the lossless line is represented by only a series reactance
(X) given by
X = Zn sin θ (1.18)
6. PRINCIPLE OF TRANSMISSION SYSTEMCOMPENSATION
The large interconnected transmission networks (made up of predominantly overhead
transmission lines) are susceptible to faults caused by lightning discharges and decrease
in insulation clearances by undergrowth. The power flow in a transmission line is
determined by Kirchhoff’s laws for a specified power injections (both active and
reactive) at various nodes. While the loads in a power system vary by the time of the
day in general, they are also subject to variations caused by the weather (ambient
temperature) and other unpredictable factors. The generation pattern in a deregulated
environment also tends to be variable (and hence less predictable). Thus, the power
Flow in a transmission line can vary even under normal, steady state conditions. The
occurrence of a contingency (due to the tripping of a line, generator) can result in a
sudden increase/decrease in the power flow. This can result in overloading of some
lines and consequentthreat to system security.
A major disturbance can also result in the swinging of generator rotors which contribute
to power swings in transmission lines. It is possible that the system is subjected to
transient instability and cascading outages as individual components (lines and
generators) trip due to the action of protective relays. If the system is operating close to
the boundary of the small signal stability region, even a small disturbance can lead to
large power swings and blackouts.
The increase in the loading of the transmission lines sometimes can lead to voltage
collapse due to the shortage of reactive power delivered at the load centers. This is due
to the increased consumption of the reactive power in the transmission network and the
characteristics of the load (such as induction motors supplying constant torque).
The factors mentioned in the previous paragraphs point to the problems faced in
maintaining economic and secure operation of large interconnected systems. The
problems are eased if sufficient margins (in power transfer) can be maintained. This is
not feasible due to the difficulties in the expansion of the transmission network caused

17
by economic and environmental reasons. The required safe operating margin can be
substantially reduced by the introduction of fast dynamic control over reactive and
active power by high power electronic controllers. This can make the AC transmission
network `flexible' to adapt to the changing conditions caused by contingencies and load
variations. Flexible AC Transmission System (FACTS) is defined as `Alternating
current transmission systems incorporating power electronic-based and other static
controllers to enhance controllability and increase power transfer capability'. The
FACTS controller is defined as `a power electronic based system and other static
equipment that provide controlof one or more AC transmission system parameters'.
7. NEED FOR FACTS CONTROLLERS – TYPE OF FACTS
CONTROLLERSAND BENIFITS
Since the ʺother static controllersʺ based FACTS devices are not widely used in current
PSs, the focused only on the power electronics based FACTS devices. The FACTS
controllers are classified as follows:
1. Thyristor controlled based FACTS controllers such as TSC, TCR, FC‐TCR,
SVC, TCSC, TC‐ PAR etc.
2. VSI based FACTS controllers such as SSSC, STATCOM, UPFC, GUPFC,
IPFC, GIPFC, HPFC etc.
The main drawback of thyristor controlled based FACTS controllers is the resonance
phenomena occurs but VSI based FACTS controllers are free from this phenomena. So
that the overall performance of VSI based FACTS controllers are better than of that the
thyristor controlled based FACTS controllers.
FACTS Categoriesand TheirFunctions
1) FACTS Categories
In general, FACTS devices can be divided into four categories on basis of their
connection diagram in PSs mentioned in table 1:
1) Series Connected ‐FACTS Devices:
Series FACTS devices could be variable impedance, such as capacitor, reactor, etc.,
or power electronics based variable source of main frequency, sub synchronous and
harmonic frequencies (or a combination) to serve the desired need. In principle, all
series FACTS devices inject voltage in series with the transmission line.
2) Shunt Connected ‐FACTS Devices:
Shunt FACTS devices may be variable impedance, variable source, or a combination
of these. They inject current into the system at the point of connection.

18
3)Combined Series‐series Connected ‐FACTS Device:
Combined series‐series FACTS device is a combination of separate series
FACTS devices, which are controlled in a coordinated manner.
4)Combined Series‐shunt Connected ‐FACTS Device:
Combined series‐shunt FACTS device is a combination of separate shunt
and series devices, which are controlled in a coordinated manner or one
device with series and shunt elements.
Possible Benefits from FACTS Technology
Within the basic system security guidelines, the FACTS devices enable the
transmission system to obtain one or more of the following benefits:
 Control of power flow as ordered. This is the main function of FACTS devices.
The use of power flow control may be to follow a contract, meet the utilities’
own needs, ensure optimum power flow, ride through emergency conditions, or
a combination of them.
 Increase utilization of lowest cost generation.
One of the principal reasons for transmission interconnections is to utilize the
lowest cost generation. When this cannot be done, it follows that there is not
enough cost‐effective transmission capacity. Cost‐effective enhancement of
capacity will therefore allow increased use of lowest cost generation.
 DS enhancement. This FACTS additional function includes the TS improvement,
POD and VS control.
 Increase the loading capability of lines to their thermal capabilities, including
short term and seasonal demands.
 Increased system reliability.
 Elimination or deferral of the need for new transmission lines.
 Added flexibility in sitting new generation
 Provide secure tie‐line connections to neighboring utilities and regions thereby
decreasing overall generation reserve requirements on both sides.
 Upgrade of transmission lines.
 Increased system security.
 Reduce RP flows, thus allowing the lines to carry more AP.
 Loop flow control.

19
8 VOLTAGE CONTROLBYSVC- ADVANTAGES OF SLOPE IN DYNAMIC
CHARACTERISTICS
Static Var Compensator(SVC), a first generation FACTS controller is taken up for
study. It is a variable impedance device where the current through a reactor is
controlled using backto back connected thyristor valves. The application of thyristor
valve technology to SVC is an offshootof the developments in HVDC technology. The
major difference is that thyristor valves used in SVC are rated for lower voltages as the
SVC is connected to an EHV line through a step down transformer or connected to
the tertiary winding of a power transformer. The application of SVC was initially for
load compensation of fast changing loads such as steel mills and arc furnaces. Here the
objective is to provide dynamic power factor improvement and also balance the currents
on the sourceside whenever required. The application for transmission line
compensators commenced in the late seventies. Here the objectives are:
1. Increase power transfer in long lines
2. Improve stability with fast acting voltage regulation
3. Damp low frequency oscillations due to swing (rotor) modes
4. Damp subsynchronous frequency oscillations due to torsional modes
5. Controldynamic overvoltages
A SVC has no inertia compared to synchronous condensers and can be extremely fast in
response(2-3 cycles). This enables the fast controlof reactive power in the control
range.
The location of SVC is important in determining its effectiveness. Ideally, it should be
located at the electrical centre of the system or midpoint of a transmission line. For
example, consider a symmetric lossless transmission line with SVC connected at the
midpoint (see Fig. 2.1). Without SVC, the voltage at the midpoint is given by,
Fig 2.1 A transmission line with SVC connected at mid point

20
Fig 2.2 Control characteristics of SVC
Vmo = V cos δ/2
cos θ/2 (2.1)
where θ= βl is the electrical length of the line, l is the length of the line
and β¯ is the phase constant given by
β = ω√lc = 2Πf√lc (2.2)
where l and c are positive sequence inductance and capacitance of the line
per unit length, f is the operating frequency.
It can be shown that the voltage variation in the line (due to variation in δ) is maximum
at the midpoint. SVC helps to limit the variation by suitable control. The steady state
control characteristics of SVC is shown in Fig. 2.2 where ADB is the control range. OA
represents the characteristic where the SVC hits the capacitor limit, BC represents the
SVC at its inductor limit. Note that SVC current is considered positive when SVC
susceptanceis inductive. Thus
ISV C = -B SV C V SV C (2.3)
The slope of OA is BC (susceptanceof the capacitor) and the slope of OBC
is BL (susceptanceof the reactor). A positive slope (in the range of 1-5%)
is given in the control range to
(a) enable parallel operation of more than one SVC connected at the same
or neighboring buses and
(b) prevent SVC hitting the limits frequently.
The steady state value of the SVC bus voltage is determined from the intersection of the
system characteristic and the controlcharacteristic (see Fig. 2.3). The system
characteristic is a straight line with negative slope and is defined by

21
Fig 2.3 Determination of operating point of SVC
VSV C = VTh - XThISV C (2.4)
where VTh and XTh are the Thevenin voltage and reactance viewed from the
SVC bus. For the system shown in Fig. 2.1, we have
VTh = Vmo = V cos δ/2
cos θ/2 (2.5)
XTh = Zn tan(θ/2)
2 (2.6)
where Zn is the surge impedance defined by
Zn = √ l
C (2.7)
9 INFLUENCE OF SVC ON SYSTEM VOLTAGE
(a) Control Range: The SVC control range is described by
VSV C = Vref + XsISV C (2.8)
where Xs is the slope of the control characteristic. Vref is the SVC voltage
(corresponding to point D) when I SV C = 0.
Combining eqs (2.4) and (2.8), we get
VSV C = Vm =V ThXs + VrefXTh
Xs + XTh Xs + XTh (2.9)
The expression for power flow in the line is given by
P = VmV sin(δ/2)
Zn sin(θ/2) (2.10)
With Vref = V , it can be shown that P is given by,
P = kP0 + (1 - k)P1 (2.11)

22
Where P0 = V² sin δ ; P1 = V² sin(δ/2)
Zn sin θ ‘ Zn sin(θ/2) (2.12)
and
k = Xs
Xs + XTh (2.13)
1. P0 is the power flow in the line without SVC and P1 is the power flow
in the line when SVC maintains a constant voltage V at the midpoint (Xs = 0)
2. k 1 as Xs ∞
3. Forsmall values of θ, it can be assumed that sin θ ' ≈θ, sin θ/2 ≈' θ/2 ,
cos θ/2 ≈ 1.
In this case,
P0 = V²Sin δ ; P1 = 2 V² sin δ/2
XL XL
where XL = (ωl)d is the total reactance of the line (d is the length of the line).
(b) At SVC limits: When the SVC hits the limit it can be represented as a fixed
susceptance(BSV C) where BSV C = BC at capacitive limit. At the
inductive limit, BSV C = -BL.
Substituting ISV C from eq. (2.3) in eq. (2.4), we get
VSV C = VSV C = V cos(δ/2)
(1 - XThBSV C) (1 - XThBSV C) cos(θ/2) (2.14)
The power flow in the line is given by
P = P0 = V² sin δ
(1 - XThBSV C) Zn(1 - XThBSV C) sin θ (2.15)
10 DESGN OF SVC VOLTAGE REGULATOR
There are two types of SVC:
1. Fixed Capacitor-Thyristor Controlled Reactor (FC-TCR)
2. Thyristor Switched Capacitor - Thyristor Controlled Reactor (TSC-TCR).
The second type is more Flexible than the first one and requires smaller rating of the
reactor and consequently generates less harmonics. The schematic diagram of a TSC-
TCR type SVC is shown in Fig.2.5. This shows that the TCR and TSC are connected on
the secondary side of a step-downtransformer. Tuned and high pass filters are also

23
connected in parallel which provide capacitive reactive power at fundamental
frequency. The voltage signal is taken from the high voltage SVC bus using a potential
transformer. The TSC is switched in using two thyristor switches (connected back
to back) at the instant in a cycle when the voltage across valve is minimum and
positive. This results in minimum switching transients. In steady state, TSC does not
generate any harmonics. To switch off a TSC, the gate pulses are blocked and the
thyristors turns off when the current through them fall below the holding currents. It is
to be noted that several pairs of thyristors are connected in series as the voltage rating of
a thyristor is not adequate for the voltage level required. However the voltage ratings of
valves for a SVC are much less than the voltage ratings of a HVDC valve as a step
down transformer is used in the caseof SVC. To limit di in a TSC it is necessary to
dt
provide a small reactor in series with the capacitor.
Fig 2.5 Atypical SVC (TSC-TCR)configuration
The block diagram of basic SVC Controller incorporating voltage regulator
is shown in Fig.2.11. This shows that both voltage (VSV C) and current
(ISV C) signals are obtained from potential and current transformers and
then rectified. The AC filter is basically a notch filter to eliminate the
signal component of frequency corresponding to the parallel resonance in
the system viewed from the SVC bus. The line capacitance (in parallel with
SVC capacitance) can result in parallel resonance with the line inductance.
The SVC voltage regulator has a tendency to destabilize this resonant mode
of oscillation and the notch filter is aimed at overcoming this problem. As
a matter of fact, any parallel resonance mode (of frequency below second
harmonic) can have adverse interaction with SVC voltage regulator. If series
capacitors are used along with SVC, then they can cause parallel resonance
with a neighboring shunt reactor. If the second (parallel resonance) mode
has a lower frequency (say below 20 Hz), a high pass filter in addition to the
notch filter has been suggested.

24
Fig 2.11 SVC Controller
The rectified signal is filtered. The DC side filters include both a low pass filter (to
remove the ripple content) and notch filters tuned to the fundamental and second
harmonic components. The notch filters are provided to avoid the adverse interactions
of SVC caused by second harmonic positive sequence and fundamental frequency
negative sequence voltages on the SVC bus. For example, second harmonic positive
sequence voltages at the SVC bus cause a fundamental frequency componentin the
rectified signal that results in the modulation of SVC susceptanceat the same
frequency. This in turn (due to amplitude modulation) results in two components at side
band frequencies (0,2f) in the SVC current. The dc component can result in un
symmetric saturation of the SVC transformer and consequent increase in the
magnetization current containing even harmonics. It has been observed that this adverse
harmonic interactions between the SVC and the network can result in large distortion of
the SVC bus voltage and impaired operation of SVC (termed as second harmonic
instability).
The auxiliary signals mentioned in Fig.2.11 are outputs from the Susceptance(or
reactive power) Regulator (SR) and Supplementary Modulation Controller (SMC). The
SusceptanceRegulator is aimed at regulating the output of SVC in steady state such
that the full dynamic range is available during transient disturbances. The output of
SusceptanceRegulator modifies the voltage reference Vref in steady state. However its
operation is deliberately made slow such that it does not affect the voltage regulator
function during transients. In contrast to the SusceptanceRegulator, the Supplementary
Modulation Controller (SMC) is designed to improve the performance of SVC
during transient conditions and not affect the steady state. SMC has control input using
appropriate signal obtained from local measurements and provide a limited output at
either the summing junction before the voltage regulator or after it. Thus, it modulates
directly either the SVC bus voltage or susceptancein order to damp oscillations and
improve stability. The gate pulse unit for SVC produces firing pulses for TCR and
TSC. The logic determines whether a TSC is to be switched in or out.
ref ref ref
B TCR is calculated from BSV C and if BTCR ≥· 0, then a TSC is switched
in.

25
ref
If BTCR ≤ BL, then a TSC is switched out.
Ref ref
In computing BTCR from BSV C
the effect of leakage reactance of the step down transformer is to be
considered as BSV C is given by
BSV C = - Bσ (BC - BTCR)
(BC - BTCR - Bσ)
= BC - BTCR
(1 - (BC - BTCR)
Bσ (2.16)
where BC is the capacitance of the fixed capacitor or TSC. Bσ »1/Xσ
;Xσ is the leakage reactance of the transformer. If Bσ À BC or- BTCR then,
BSV C ≈ (1 + BC ) BC - [1 +(2BC - BL) ]BTCR
Bσ Bσ
= C1 - C2BTCR (2.17)
BL is the reciprocal of XL and is the maximum value of TCR susceptance.
Neglecting leakage reactance of the transformer, the variation of BTCR with variation of
BSV C for a casewith two identical TSC's is shown in Fig.2.12. This shows that BL (the
rating of TCR) is slightly larger than the rating of either TSC and there is hysteresis in
the operation of the TSC. This is desirable as the switching of a TSC is not well defined
if BC1(susceptanceof a TSC)is exactly equal to BL. If BC1 is greater than BL, then the
operation of the SVC is degraded.
Fig 2.12 Variation VTCR with BSVC for TSC-TCR type SVC
For stability studies, it is not essential to model GPU. In this case, the modelling of the
controller shown in Fig.2.11 can be simplified greatly by also assuming that SVC does
not generate harmonics. The block diagram of the controller in this case is shown in
Fig.2.13. Here the voltage regulator is typically a PI controller as shown in Fig.2.14.

26
The proportional gain (KP ) may be set zero unless a faster responseis required. The
transfer function Hm(s) represents a low pass filter as given below:
First order filter
Hm(s) = 1
1 + sTm (2.19)
Fig 2.13 Block Diagram of SVC voltage control
Fig 2.14: Voltage Regulator for SVC
Second order LP filter:
Hm(s) = 1
1 + 2sζTm + (sTm)² (2.20)
Tm is typically 2 to 3 ms and ζ = 0:7.
The transport delay, Td is typically
Td = T/12 (2.21)
where T is the period of the supply voltage. Td arises due to the discrete
nature of the firing pulse. Tb represents the average delay in getting BSV C
from the instant of delivering the order and is given by

27
Tb = T /4 (2.22)
It is to be noted that Tb represents maximum (average) delay when
ref
the BTCR changes from maximum (BL) to zero.
In Fig.2.11 or Fig.2.13, the current signal ISV C is used to provide a positive slope for the
control characteristic of SVC. However the current signal contains harmonics and there
are measurement problems particularly
when ISV C is close to zero (the normal operating point) . A solution to this
ref
problem is to take the signal from BSV C instead of ISV C.
In this case, the block diagram of Fig.2.13 can be simplified as shown
in Fig.2.15. Here, assuming KP = 0,
KR = 1/ Xs (2.23)
and
TR = KR/KI (2.24)
KR (typically) varies from 20 to 100, whereas TR varies between 20 to 150 ms.
Fig2.15: Simplified Block Diagram of SVC Voltage Control
Control Instability and Gain Supervisor
The transfer function between change in the SVC susceptance ΔBSV C and
the change in the SVC voltage ΔVSV C is independent of frequency if only
fundamental component of VSV C is considered. Assuming the operating
voltage at SVC bus as unity, then
Δ VSV C ≈ XTh ΔBSV C (2.25)
The loop gain of the control system shown in Fig.2.15 depends on XTh.
The speed of the responsedepends on the loop gain and increases as XTh is increased.
However for high values of XTh the system can be unstable. The voltage regulator of
SVC is designed to provide the fastest response correspondingto a contingency
condition at which XTh is maximum (in the range of operating conditions considered) or

28
the short circuit level at the SVC bus is minimum. However, during abnormal
conditions resulting in tripping of several transmission lines in the system, XTh will be
higher than the design value and the SVC controller can be unstable. In such cases,
it is necessary to reduce the gain of SVC (KI ) automatically by detecting instability.
This is called as gain supervisor. The gain is restored to the normal value when the
instability is not present. It is to be noted that although instability can be avoided by
designing the voltage regulator gain corresponding to the lowest value of short circuit
level (highest value of XTh)this is not an optimal choice as the responseof SVC will be
slower under normal conditions.
The transfer function
(ΔVSV C / ΔBSV C) is in general, a function dependent on frequency if network
(electromagnetic) transients are considered. The magnitude of the transfer function is
maximum at frequency, fr defined by
fr = fNp - fo (2.26)
where fNp is the frequency correspondingto the parallel resonance in the network and
fo is the operating frequency. The controller gain will be severely restricted even under
normal conditions if fr is within the controller bandwidth. Hence the practical solution
to this problem is to provide a notch filter in the controller (on the input side) as
mentioned earlier.
Susceptance Regulator(SR)
A typical SR is shown in Fig.2.16. Here the output of the voltage regulator,
Ref set
BSV C and a set reference B SV C are compared. If the error exceeds a threshold, it
activates an integrator after an adjustable time delay (of the order of
several seconds). Theintegrator output is hard limited by a non-wind up
limiter and modifies the voltage reference.
The SR has to be coordinated with other reactive power controllers in
the vicinity such as HVDC converter control, switched capacitor and reactor
banks, tap changing transformers etc.
Fig 2.16: SusceptanceRegulator
Supplementary Modulation Controller (SMC)
This controller modulates either VSV C or BSV C by processing a signal obtained from
local measurements. The objective is to damp critical low frequency inter area or local

29
modes that can affect stability during disturbances. The controlsignals are selected on
the basis of following criteria
1. The signal should predominantly contain the mode that needs to be damped.
2. The controller design based on a particular controlsignal should be
simple and reject noise.
3. The controller should not destabilize modes that are otherwise stable.
4. The controller should be effective and robustunder widely varying operating
conditions.
The controlsignals that have been used or suggested include: (1) line current (2) active
and reactive power (3) bus frequency (4) Computed Rotor Frequency (CRF)and (5)
Computed Thevenin voltage. The last two signals are synthesized from current and
voltage measurements at the SVC location.
A typical controller configuration of SMC is shown in Fig.2.17. The washout circuit is
designed to drive the SMC output to zero during steady state. The gain and phase
compensation of SMC are chosen such that it improves the system responseunder a
wide variety of operating conditions and different types of disturbances.
Figure 2.17: Block Diagram of SMC
Protective Functions of SVC control
The SVC controlalso has functions to provide protection under faulted or overload
conditions that may affect the equipment or system response. These are listed below.
1. Undervoltage Strategy
The SVC is ineffective under low voltage conditions due to faults in the system.
However, the clearing of the fault can result in temporary overvoltages due to load
rejection, particularly under weak system conditions. The responseof the SVC required
immediately after the fault clearing is opposite of the normal voltage regulator function
during a fault. To avoid delay in the required responseof the SVC, the normal voltage
regulator action is deactivated when voltage falls below a threshold (say 60% of the
normal
ref
voltage). TSC is blocked and BSV C is frozen at the previous value (prior to the voltage
dip). The normal SVC regulator action is resumed after the voltage climbs above a
certain threshold (say 70%) and remains (above the threshold) there for sometime (say
30 ms). The blocking of TSC also helps in reducing the transient by preventing the
capacitor discharge.
2. TCR Over current Limiter

30
Under high voltage conditions, the SVC will be at its inductive limit and the TCR
current may exceed its rated value. To protect the thyristor valves used in TCR, it is
necessary to limit the current through it by phase control. To avoid interaction with
voltage regulator function, a time delay is introduced (of the order of 100 ms). The
overcurrent limiter takes into account the short-term overload capability of the TCR.
3. SVC Control Interactions at Subsynchronous Frequencies
The SVC voltage regulator can adversely affect the damping of the subsynchronous
frequency torsional modes due to turbine-generator rotors and elastic shafts
(constituting a lightly damped mass-spring-damper system). Unlike in the case of fixed
series capacitors, the Torsional Interaction (TI) problem with SVC is not very
significant. It has been suggested that the use of low pass filter or Transient Gain
Reduction (TGR) in conjunction with the voltage regulator is adequate to overcome the
problem.
Voltage RegulatorDesign
Speed of Responseas Function of ESCR
As mentioned in the previous section, the voltage regulator is of PI (Proportional -
Integral) type. Neglecting limiters, measurement and transport delays, the voltage
regulator loop can be simplified as shown in Fig.2.18.
Here, the transfer function ΔVSV C(s)/ΔBSV C(s) is assumed to be a static gain (KN),
neglecting the network dynamics.
The expression for KN is obtained from the equivalent circuit shown
in Fig.2.19. It is to be noted that the operating values of the SVC suscep-
tance (Bsvco) is considered as part of the network and XTh is calculated at
the operating point. The SVC bus voltage (VSV C) is obtained from Fig.2.19
as
VSV C = VTh ≈ VTh (1 + XThΔBsvc)
(1 - XThΔBsvc) '
From the above, we get ΔVSV C as
Δ VSV C = VSV C – VTh = VTh XThΔBsvc
= KNΔBsvc (2.27)
where
KN = VThXTh (2.28)

31
Fig2.18: Simplified system block diagram
Assuming VTh ≈ 1:0, we can also write
KN ≈' XTh = 1 = QSV C
ESCR SC (2.29)
The Effective Short Circuit Ratio (ESCR)is defined as the ratio of the
short circuit level to the rating of the SVC. In defining ESCR it is assumed
that the operating value of BSV C is merged with the network admittance in
computing the short circuit level (in MVA).
Figure 2.19: An equivalent circuit
In Fig. 2.18, the feedback from ISV C is obtained as KIΔBSV C. This
follows from the relation
- XsΔISV C = XsΔBSV C = KIΔBSV C (2.30)
In deriving (2.28) it is assumed that VSV C ≈ 1:0 and BSV C0 = 0 in linearizing Eq. (2.3).
The transfer function of the voltage regulator (GR) is assumed as
GR(s)= KC {1 + sTC} (2.31)
sTC
By selecting TC = Tb and KC = 1
2(KI+KNmax) where KNmax correspondsto
the operating point with lowest value of ESCR, we get a regulator with fast response
with good margin of stability. The closed loop transfer function [Gc(s)]is obtained as
Gc(s)= ΔVSV C(s)
ΔVref (s)
= KN { 1 }

32
KN + KI 1 + sTw ( 2.32)
where
Tw = 2(KI + KNmax) Tb
(KI + KN) (2.34)
As KN increases to KNmax, Tw reduces to a value of 2Tb = T/2 (10 ms for the nominal
frequency of 50 Hz). For a step input in ΔVref , the variation in ΔVSV C is given by
ΔVSV C(t) = KN ΔVref (1 - e inverse to the power Tw)
KN + KI (2.35)
The responsetime (to reach 95% of the final value) is 3Tw. The fastest responsetime
for the minimum value of ESCR is 30 ms (for the 50 Hz system).
11 Modelling of SVC
For a detailed study of SVC controlinteractions, it is necessary to perform transient
simulation for which SVC is modelled in detail including the switching of the thyristor
valves in TCR and TSC. The transient network is modelled by differential equations
rather than algebraic equations .
However for stability study it is not necessary to consider the switching of valves and
assume that SVC generates only fundamental current. In addition, the network
transients are neglected and represented by algebraic equations of the type:
[Y ]V = I (2.36)
With these simplifications, SVC can be modelled as a variable susceptance
which is the output of the control system as shown in Fig.2.13. If SMC is
a part of the SVC controller, it should be included in the model. However,
susceptanceregulator, gain supervisor and the protective functions can be
neglected in the model.
For the preliminary studies, it is adequate to ignore the dynamics of SVC control
(without SMC) and assume that the SVC is described by its steady state control
characteristics. If SMC is present, it can be modeled as shown in Fig. 2.17.
Steady State Model of SVC
The steady state control characteristics are modelled by an equivalent circuit
shown in Fig. 2.32. This shows a complex voltage source ÉSV C in series with
a reactance XSV C. The losses in the SVC are neglected. The values of ^ESV C
and XSV C are given below for the SVC operating in (i) the control range,
(ii) capacitive limit and (iii) inductive limit
(i) Control Range
ÉSV C = Vref ∟Øsvc (2.37)

33
XSvc = Xs (2.38)
where Øsvc is the angle of the SVC bus voltage. The control range applies
when the SVC bus voltage lies in the range
Vref < VSV C < Vref
1 + XsBmax 1 + XsBmin (2.39)
where Bmin and Bmax are the limits of BSV C. Note that Bmin is, in gen-
eral, negative (corresponding to the inductive limit) and Bmax = BC, where
BC is the total capacitive susceptance. (neglecting the transformer leakage
reactance)
(ii) At Capacitive Limit :
ÉSV C = 0.0 + j0.0 XSV C = - 1/Bmax (2.40)
(iii)At inductive Limit :
ÉSVc = 0.0 + j0.0 XSV C = - 1 / Bmin (2.41)
Fig 2.32: Equivalent circuit of SVC
The equivalent circuit of SVC for the controlrange is nonlinear (since the angle of ÉSV C
depends on the bus voltage) and is time varying when the limits are considered. Thus,
in general, the inclusion of SVC model in transient stability simulation, involves
iterative network solution. However, with nonlinear voltage dependant static load
models in the system, the handling of SVC is no more complicated than the handling of
nonlinear loads. If only one SVC is to be considered, the network solution with SVC
can be considerably simplified by applying compensation theorem. In this approach, the
SVC is treated as a time varying current sourcewhich can be computed from the
solution of a simple network shown in Fig.2.33. Here, the network external to the SVC
is modelled by a time-varying Thevenin equivalent. If the network impedances are

34
constant, Zeq remains constant. Zeq is calculated as the impedance of the network seen
at the SVC terminals when all the sources in the network are removed ( the voltage
sources are shorted and the current sources are open circuited). V’eq is found as the
SVC terminal voltage with the SVC current zero. V’eq varies with time as the
generator voltages vary during a disturbance. From Fig.2.33, the SVC current can be
computed as
ÌSV C = V’eq - ÉSV C
Zeq + jXSV C (2.42)
Fig 2.33: SVC connected to Thevenin equivalent
If ÉSV C = 0:0+j0:0,the solution is straight forward. However, in the control
range, the angle ØSV C needs to be known to apply Eq.(2.42).
It can be shown that tan ØSV C is obtained as the solution of a
quadratic equation given by
a tan² ØSV C + b tan ØSV C + c = 0 (2.43)
where
a = x² - z² sin²α;
b = - 2xy;
c = y² -¡ z² sin² α
x = Re[(1 - Á)V’eq] ; y = Im[([(1 - Á)V’eq]
z = Á Vref
Á = A∟α = Zeq
Zeq + jXSV C
Network Solution
The network solution is carried out in two steps. In the first step, the voltage
solution is obtained by putting ÌSV C = 0. The voltage calculated at the SVC
bus, at the end of the first step is same as V’eq. The knowledge of V’eq and Zeq
(which has been calculated in advance and stored) enables the computation
of ÌSV C from Eq. (2.42) and Eq.(2.43) (if required). The network is solved again with
the injection of ÌSV C at the SVC bus (all other sources put equal to zero).The second
solution requires minimal computations as the current vector is sparse.
The voltage at all the buses are obtained from the addition (superposition) of the two
sets of the voltage calculated in the two network solutions.
Remarks

35
1. It is assumed, in the calculation of Zeq, that the generators have no dynamic saliency.
Dynamic saliency results in time varying impedance of the stator (with respectto the
network or common synchronously rotating reference frame). Also, the generator
impedance needs to be expressed as a 2 ¤ 2 matrix in D-Q axes. In this case, it can be
shown that ÁSV C is obtained from solving a quartic equation.
2. Zeq changes whenever there is change in the network configuration.
3. If Zeq is purely reactive (inductive) impedance, then ÁSV C is the phase angle of
V’eq, which is known. This eliminates the need for the solution of Eq. (2.43).
4. The appropriate solution of ÁSV C obtained from Eq. (2.43) is the one
which is closer to the phase angle of V’eq.
12 Applications of SVC
The major application of SVC is for rapid voltage regulation and control of dynamic
(temporary) overvoltages caused by load throw of, faults or other transient disturbances.
The dynamic reactive control at the load bus increases power transfer and can solve the
problem of voltage instability (collapse) caused by contingency conditions. It is to be
noted that steady state voltage regulation can be achieved by mechanically switched
capacitors and reactors (MSC and MSR). However, fast voltage regulation is required
to prevent instability under transient conditions. Thus, generally, a SVC is operated
with minimum reactive power output under normal conditions. This is achieved by the
SusceptanceRegulator described earlier which ensures that full dynamic range is
available for controlunder contingency conditions. The fast controllability provided by
the thyristor switches can be also utilized to improve system stability (both transient
and small signal). The use of auxiliary damping controllers can help damp low
frequency, interarea power oscillations that can appear at stressed operating conditions
(involving high loading of tie lines). The design of such damping controllers for shunt
and series FACTS controllers will be taken up separately .The location of SVC is an
important issue. If the objective is to compensate a long transmission line, the SVC is to
be located at the midpoint of the line (if a single SVC is to be used). For very long lines,
multiple SVC at regular intervals can be applied. Forexample, if two SVCs are to be
used, one is located at a distance d /3 from the sending end while the other is located
at a distance, d / 3 from the receiving end (d is the length of the line). When SVCs are
applied to improve the power transfer in a transmission network, the location can be
determined by the sensitivity of voltage at the critical buses with respect to the reactive
power injection (ΔVi/ΔQj ). In general, it can be stated that a bus with low short circuit
level can be a candidate bus. Incidentally a synchronous condenser can raise the fault
level while providing controllable reactive power. It is to be noted that a SVC does not
raise the fault level which can be a blessing as the requirement of the fault current
interruption capability of circuit breakers does not go up. On the other hand, for reactive
power control at HVDC converter stations with low Short Circuit Ratios (SCR), the
synchronous condenserimproves voltage regulation and system performance.
However, a SVC has several advantages over SC (synchronous condenser) namely,
(a) Faster responseunder transient conditions
(b) There are no moving parts, hence requires less maintenance

36
(c) There are no problems of loss of synchronism
(d) As mentioned earlier, a SVC doe not contribute to short circuit currents.
The drawbacks of a SVC are mainly related to the injection of current harmonics. These
can be minimized by segmented TCR (with several segments/modules of TCR
connected in parallel) and operating all except one module in the TSR (Thyristor
Switched Reactor) mode. The preparation of specification of a SVC, the design and
testing of the controller requires detailed studies involving power flow, short circuit and
stability analysis in addition to studies involving a TNA (Transient Network Analyzer)
or RTDS (Real Time Digital Simulator). The steady state control (V-I) characteristics
are defined by the SVC rating (in MVAR), range of the reference voltage (Vref )
(typically from 0.95 pu to 1.05 pu) and the slope (varying from 2% to 10%). The slopes
can be different in the capacitive and inductive modes of operation. The range of short
circuit levels at the SVC bus is also an important parameter in the choice of the voltage
regulator gain. In the past, saturable reactors have been applied in situations when
temporary overvoltages can be a critical factor. However, in recent times, Thyristor
Controlled Transformer (TCT)where the leakage reactance of the step down
transformer can be used to replace the reactor has been suggested to provide
controllable shunt reactors in long EHV transmission lines. The costconsiderations will
determine whether such innovations will be applied in practice.
13 STEADY STATE POWER TRANSFER , ENHANCEMENTOF POWER
SYSTEM DAMPING, PROVISION OF VOLTAGE STABILITY
PowerAngle Curve for SVC
The power angle curve for SVC is made up of 3 segments correspondingto
(i) BSV C = -BL,
(ii) control range
(iii) BSV C = BC.
For typical value of parameters, the power (expressed in per unit of Pn =
Surge Impedance Load) as a function of ± is shown in Fig. 2.4. The power
angle curve for the line without SVC is also shown in Fig. 2.4 (curve b).
Fig 2.4: Plot of Power Vs δ

37
Consider a simplified system as seen from the terminals of the static
shunt compensator (shown in Fig. 2.20).
Figure 2.20: A simplified representation for interaction with network resonance
The positive sequence driving point impedance ZTh(s) in the Laplace domain, at the SVC bus is given
by
ZTh(s) = (R + sL)
(s²LC + sRC + 1) (2.44)
The equations in the D-Q (synchronously rotating reference frame)
variables are given by
VSD(s) = ZDD(s) ZDQ(s ) IRD(s)
VSQ(s) ZQD(s) ZQQ(s) IRQ(s) (2.45)
where
ZDD(s) = ZQQ(s) = ZTh(s + jω‫ט‬) + ZTh (s - jω‫ט‬)
2 (2.46)
ZQD(s) = -ZDQ(s) = j ZTh (s + jω‫ט‬) -ZTh ZTh (s - jω‫ט‬)
2
= -Im[ZTh (s + j ω‫ט‬)] (2.47)
The D-Q components of the SVC bus voltage (VS) and current (IR) are
shown in Fig. 2.21.
Fig 2.21: A phasordiagram
From Fig.(2.21), we have
VSD = VS sin θ; VSQ = VScos θ (2.48)

38
From Eq. (2.48), we get
ΔVS = sin θ‫ט‬ΔVSD + cos θ‫ט‬ΔVSQ (2.49)
If we assume that the current injected by the SVC is purely reactive, we
have
IRQ = -R sin θ; IRD = IR cos θ (2.50)
From Eq. (2.50), we get
ΔIRD(s) = cos θ‫ט‬ IRo - sin θ‫ט‬
ΔIRQ(s) - sin θ ‫ט‬ ΔIR(s) + - cos θ‫ט‬ Δθ(s)
= cos θ‫ט‬
-sin θ‫ט‬ ΔIR(s) ( 2.51)
We have assumed IRo = 0 as before. Linearizing Eq. (2.45), and substituting
from (2.50) and (2.51), we get
ΔVS(s) = ZQD(s) = KN(s)
ΔIR(s) D(s) (2.52)
where N(s) and D(s) are the numerator and the denominator polynomials,
where
K = (ω‫ט‬L)ωη²
D(s) = [s + σ + j(ω - ω‫ט‬)][s + σ - j ω - ω‫ט‬)] [s + σ + j(ω +- ω‫ט‬)][s + σ - j(ω + ω‫ט‬)]
N(s) = s² + 2R s + R²+ ω‫²ט‬ - 1
L L² LC
σ = R ω = √ ωη² - σ² , ωη = 1
2L √LC
When R ≈ 0, then
N(s) ≈ s² + ω‫²ט‬-- 1
LC
= s² + ω‫²ט‬ - ωη² (2.53)
Since ω‫ט‬ > ω‫ט‬, the numerator polynomial N(s) has a pair of real zeros given
by

39
s = ± √ ωη² - ω‫²ט‬ (2.54)
Thus, the transfer function ΔVs(s)
ΔIr(s) is a non-minimum phase type with a zero
in the R.H.P. (on the positive real axis). The controlof plants with non-
minimum phase type is always problematic and requires compensation to enable the use
of P-I controlwith high gains.
Remarks
1. The four poles of the transfer function ΔVS(s) all lie in the L.H.P. and are given by
ΔIR(s)
p1, p2 = -σ ± j(ω - ω‫ט‬); p3, p4 = -σ ± j(ω + ω‫ט‬)
where -σ ± jω are the poles of the impedance function ZTh(s).
3. For R ≈ 0, it can be shown that the transfer function reduces to
ΔVS(s) ≈ ω‫ט‬Lωη² (s²- ωη² + ω‫ט‬²)
ΔIR(s) [ s²-(ωη - ω‫ט‬) ²] [s²+ (ωη + ω‫ט‬)²] (2.55)
Substituting for s = 0, we get
ΔVS= -XTh (2.56)
ΔIR
where
XTh =ωL = ω‫ט‬L ωη ²
1 - ω‫ט‬²LC ωη² - ω‫²ט‬
is the reactance of the parallel combination of L and C, evaluated at the
operating frequency ω‫ט‬ Eq. (2.56) can be compared with Eq. (2.27) as
IR = ISV C = -BSV CVSV C. As it is assumed that IRo = 0, VSV C0= VTh
(Note that the subscript`o' indicates the operating value of the variable).
The adverse control interactions with network resonance are functions of the ESCR and
the operating point. The lower value of ESCR and the SVC operation at capacitive
region worsen the control stability problem. The controller gain needs to be reduced to
overcome the problem. This may not be practical as the responseof SVC needs to be
fast at lower values of ESCR. One of the solution suggested in is to provide a
compensator in cascadewith the voltage regulator, that rejects the complement of the

40
network resonance frequency component. The transfer function of the compensatoris
assumed to be
Gcomp(s)=(s + σ 1)² + ωr²
(s + σ 2)² + ωr ² (2.57)
where σ1 < σ2. This transfer function represents a notch filter that rejects
the component of frequency of ωr. By arranging ωr = ωn - ω‫ט‬, the interaction between
the network resonance (of frequency ωn) and the controller can be avoided. It is to be
noted that a frequency of ωn in the AC voltage is transformed to a frequency of ωr after
demodulation in the voltage measurement circuit.
Harmonics and Filtering
The harmonics in a SVC are generated by the TCR. Neither TSC or TSR (Thyristor
Switched Reactor) generate harmonics. The current harmonics generated by TCR can
be classified into two categories:
1. Characteristic harmonics which are the harmonics present under ideal conditions
such as sinusoidal, balanced AC voltages, equidistant firing pulses, and identical values
of impedances in the three phases.
2. Uncharacteristic harmonics are the result of non-ideal conditions such as
(a) Unbalanced AC voltages, also containing harmonics
(b) Tolerances of short circuit impedances of the step-down transformer
(c) Tolerances of reactors
(d) Asymmetry of the firing angles in the phases
(e) Asymmetry of the firing angle for positive and negative half cycles of one phase.
The non-characteristic harmonics are usually less than 1/10 of the characteristic
harmonics for ΔL = 5%, Δα = 1˚ (ΔL is the tolerance in the reactors, Δα is the deviation
in the firing angle from equidistant pulse control).
However, these non-characteristic harmonics cannot be neglected. For example, a small
dc component present in the SVC current (due to firing angle asymmetry) can drive the
connecting transformer into saturation resulting in large harmonic voltages at the SVC
bus.
Harmonic Interactions
A major concern is the possibility of harmonic interactions with the AC network (Note
that this is a separate phenomenon from what was discussed in the previous section
regarding control instability). The problem of harmonic magnification (of low order
such as second or third) has been viewed by some as `harmonic instability' in the past.
The harmonic interactions with the network can arise from the following factors.
(a) Direct: Effects due to the harmonics present in the bus voltage. These harmonics
influence the harmonics in the TCR current which in turn affect the harmonic distortion

41
in the bus voltage. Normally such effects are secondaryunless the impedance seen by
the TCR current is very high.
(b) Through voltage regulation loop: The modulation of the TCR admittance at
frequency fc, results in the frequencies, f0 ± fc at the SVC bus which are picked up by
the voltage measuring circuit and may be amplified. This problem can be solved by
providing notch filters in the control circuit. To eliminate the possibility of
magnification of (positive sequence) second and third harmonics, filters at the funda-
mental frequency (f0) and second harmonic (2f0) are provided. The voltage unbalance
can result in second harmonics on the dc side and third harmonic on the ac side.
(c) Through gate pulse synchronization: Although the gate pulses are equidistant in
normal steady state, during network faults, there can be ¯ring angle asymmetries that
result in harmonics. In general, gate pulse synchronization should be insensitive to the
presence of harmonics in the bus voltage.
Harmonic Filters
The presence of harmonics (both current and voltage) is viewed as `pollution'
affecting the operation of power systems. The injection of current harmonics
by nonlinear loads also results in the distortion of the voltage waveforms due
to the system impedances. The adverse effects of the harmonics include
1. Harmonic over voltages, particularly during a transient which can also
be sustained due to inrush current phenomena in transformers.
2. Increased losses in shunt capacitor banks and rotating machines whose
impedances are much lower at harmonic frequencies than at system
frequency
3. Telephone interference.

RGPV NOTES ON FACTS EX8303 unit I & II

More Related Content

What's hot (20)

Viewers also liked (13)

Similar to RGPV NOTES ON FACTS EX8303 unit I & II (20)

More from Mani Deep Dutt (7)

Recently uploaded (20)

RGPV NOTES ON FACTS EX8303 unit I & II