Unit iii-stability

 The most important problem in linear control systems concerns stability.
 A system is said to be stable, if its output is under control. Otherwise, it is said
to be unstable.
 It is the most important system specification among the three requirements
enter into the design of a control system:
 transient response,
 stability,
 steady-state error.
 A stable system produces a bounded output for a given bounded input.

Types of Systems based on Stability
We can classify the systems based on stability as follows:
1) Absolutely stable system
2) Conditionally stable system
3) Marginally stable system

Using this concept, we present the following definition of stability,
instability and marginal stability:
 A linear time-invariant system is stable if the natural response approaches to zero as
time approaches infinity.
 The figure shown below represents the step response of an absolutely stable system:

 A linear time-invariant system is unstable if the natural responses grows
without bound as time approaches infinity.
 The figure below represents an unstable system

 A linear time-invariant system is marginally stable if the natural response
neither decays nor grows but remains constant or oscillates as time approaches
infinity.
 The figure here represents the step response of a marginally stable system

Routh-Hurwitz Stability Criterion
 Routh-Hurwitz stability criterion is having one necessary condition and one
sufficient condition for stability.
 If any control system doesn’t satisfy the necessary condition, then we can say that
the control system is unstable.
 But, if the control system satisfies the necessary condition, then it may or may not be
stable.
 So, the sufficient condition is helpful for knowing whether the control system is
stable or not.

Necessary Condition for Routh-Hurwitz Stability
 The necessary condition is that the coefficients of the characteristic polynomial
should be positive.
 This implies that all the roots of the characteristic equation should have negative real
parts.
Consider the characteristic equation of the order ‘n’ is -

Sufficient Condition for Routh-Hurwitz Stability
 The sufficient condition is that all the elements of the first column of the Routh array
should have the same sign.
 If all the roots of the characteristic equation exist to the left half of the ‘s’ plane, then
the control system is stable.
 If at least one root of the characteristic equation exists to the right half of the ‘s’ plane,
then the control system is unstable.
 So we have to find the roots of the characteristic equation to know whether the control
system is stable or unstable.
 But, it is difficult to find the roots of the characteristic equation as order increases.

 So, to overcome this problem there we have the Routh array method.
 In this method, there is no need to calculate the roots of the characteristic equation.
 First formulate the Routh table and find the number of the sign changes in the first
column of the Routh table.
 The number of sign changes in the first column of the Routh table gives the number
of roots of characteristic equation that exist in the right half of the ‘s’ plane and the
control system is unstable.

Follow this procedure for forming the Routh table:
The following table shows the Routh array of the nth order
characteristic polynomial.
 Fill the first two rows of the Routh array with the coefficients of the
characteristic polynomial as mentioned in the table below. Start with the
coefficient of sn and continue up to the coefficient of s0.
 Fill the remaining rows of the Routh array with the elements as mentioned in
the table below. Continue this process till you get the first column element
of row s0 is an. Here, an is the coefficient of s0 in the characteristic polynomial.

SPECIAL CASES OF ROUTH ARRAY
 We may come across two types of situations, while forming the Routh table.
 It is difficult to complete the Routh table from these two situations.
The two special cases are:-
1) The first element of any row of the Routh array is zero.
2) All the elements of any row of the Routh array are zero.

1) First Element of any row of the Routh array is zero
 If any row of the Routh array contains only the first element as zero and at
least one of the remaining elements have non-zero value, then replace the first
element with a small positive integer, ϵ.
 And then continue the process of completing the Routh table.
 Now, find the number of sign changes in the first column of the Routh table
by substituting ϵ tends to zero.

2) All the Elements of any row of the Routh array are zero
In this case, follow these two steps:-
1) Write the auxilary equation, A(s) of the row, which is just above the row of
zeros.
2) Differentiate the auxiliary equation, A(s) with respect to s. Fill the row of
zeros with these coefficients.

Unit iii-stability

More Related Content

What's hot (20)

Similar to Unit iii-stability (20)

More from kypameenendranathred (18)

Recently uploaded (20)

Unit iii-stability