Dräger Flame 1300 - Fixed Flame Detector - Spec Sheet
0 likes322 views
The Dräger Flame 1300 is an infrared flame detector designed for detection of organic fires such as hydrocarbons. Installation is simple using a stainless steel bracket that can be rotated for optimal positioning. It provides flexibility with multiple output options and automatic and manual optics checks to ensure reliability while detecting fires and avoiding false alarms.
Dräger Flame 1300 - Fixed Flame Detector - Spec Sheet
- 1. Simple installation Installation is simple! The detector is easily installed with a stainless steel mounting bracket; which can be rotated to ensure optimum positioning of the detector in relation to the potential fire source. Angular markings allow the positioning angles of the detector to be recorded for future reference. Detector flexibility As well as a 4 to 20 mA output and 3 relays, an optional RS 485 output is also available, which can be multi-dropped to a central location. This provides a number of options for detector monitoring and the triggering of the necessary control action upon the detection of a fire. Automatic and manual optics checks Automatic checks of the detector elec tro-nics and optics ensure no fault goes undetected. Additionally the test can be triggered manually at anytime. Isolated 4 to 20 mA as standard Complete flexibility enables the detector to be operated from a separate power supply (as a 4 wire device) or as a 3 wire device where there is no requirement for an isolated output. Easily visible status LED A tri-coloured LED which is visible at the front of the detector provides a simple status indication to personnel in close proximity to the detector. Green indicates normal operation; yellow indicates a fault and red indicates the presence of radia-tion. Worldwide Approvals The Dräger Flame 1300 can be used worldwide with the following approvals: ATEX, IECEx, FM and CSA. Dräger Flame 1300 ST-326-2008 ST-341-2004 The Dräger Flame 1300 is an IR flame detector, designed for the detection of organic based fires such as hydrocarbon fuels and vapours. The detector provides flexibility with its numerous out-put modes, and advanced design features ensure reliability in the detection of fires whilst at the same time providing excellent immunity to potential false alarm sources. Dräger Flame 1300: Explosion proof IR flame detector for hydrocarbon based fires ST-474-2004 Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: northernsales@thorneandderrick.co.uk Website: www.heattracing.co.uk www.thorneanderrick.co.uk
- 2. Dräger Flame 1300, Al housing, M20 entries 23 50 422 Dräger Flame 1300, Al housing, M25 entries 23 50 429 Dräger Flame 1300, Al housing, 1/2” NPT entries 23 50 435 Dräger Flame 1300, Al housing, 3/4” NPT entries 23 50 441 Dräger Flame 1300, SS housing, M20 entries 23 50 425 Dräger Flame 1300, SS housing, M25 entries 23 50 432 Dräger Flame 1300, SS housing, 1/2” NPT entries 23 50 438 Dräger Flame 1300, SS housing, 3/4” NPT entries 23 50 444 TECHNICAL DATA Type Explosion proof IR flame detector for hydrocarbon based fires Spectral response 4.2 to 4.7 micron Field of view Horizontal 90°, vertical 90° Sensitivity 0.1 m2 gasoline fire at 18 metres, 1 sq. foot fire at 60 feet Response time t90 3,5 seconds, typical, configurable up to 30 seconds Signal output Fault 0 mA Optics/electronics check failure 2 mA Normal operation 4 mA Fire pre-warning 16 mA Fire 20 mA (factory configurable for latching/non-latching alarm) 3 relays for fault, alarm and accessory, ratings 125 VAC, 0.5 A; 30 VDC, 2 A optional RS 485 Supply voltage 18 to 32 VDC, current consumption 160 mA quiescent state at 24 VDC Ambient conditions Temperature - 40 to + 70 °C, - 40 to + 158 °F Pressure 915 to 1055 hPa, 27.9 to 31.2 inch of Hg Humidity 0 to 99 %RH, non condensing Enclosure IP 66 / NEMA 4X Cable entry M20, M25, 1/2” NPT or 3/4” NPT Size (L x D, approx.) 275 mm x 155 mm, 10.8” x 6.1” Weight (approx.) 3.5 kg, 7.7 lbs Approvals ATEX II 2G EEx d IIC T6/T5; - 50 ≤ Tamb ≤ + 60 / + 70 °C IECEx Ex d IIC T6/T5; - 50 ≤ Tamb ≤ + 60 / + 70 °C FM/CSA Class I, Groups A, B, C, D Class I, Zone 1, Groups IIA, IIB & IIC Ex d II C; T6/T5; - 40 ≤ Tamb ≤ + 60 / + 70°C Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: northernsales@thorneandderrick.co.uk Website: www.heattracing.co.uk www.thorneanderrick.co.uk