Embedded System

Embedded Systems Unit 1
EMBEDDED SYSTEM: AN INTRODUCTION
1.1 DEFINITION OF AN EMBEDDED SYSTEM
 An embedded system is a combination of 3 things:
a. Hardware
b. Software
c. Mechanical Components. And it is supposed to do one specific task only.
 Example 1: Washing Machine
A washing machine from an embedded systems point of view has:
a. Hardware: Buttons, Display & buzzer, electronic circuitry.
b. Software: It has a chip on the circuit that holds the software which drives
controls & monitors the various operations possible.
c. Mechanical Components: the internals of a washing machine which actually
wash the clothes control the input and output of water, the chassis itself.
 Example 2: Air Conditioner
An Air Conditioner from an embedded systems point of view has:
a. Hardware: Remote, Display & buzzer, Infrared Sensors, electronic circuitry.
b. Software: It has a chip on the circuit that holds the software which drives
controls & monitors the various operations possible. The software monitors
the external temperature through the sensors and then releases the coolant
or suppresses it.
c. Mechanical Components: the internals of an air conditioner the motor, the
chassis, the outlet, etc
 An embedded system is designed to do a specific job only. Example: a
washing machine can only wash clothes, an air conditioner can control the
temperature in the room in which it is placed.
 The hardware & mechanical components will consist all the physically visible
things that are used for input, output, etc.
 An embedded system will always have a chip (either microprocessor or
microcontroller) that has the code or software which drives the system.
1.2 HISTORY OF EMBEDDED SYSTEM
 The first recognised embedded system is the Apollo Guidance
Computer(AGC) developed by MIT lab.
 AGC was designed on 4K words of ROM & 256 words of RAM.
 The clock frequency of first microchip used in AGC was 1.024 MHz.
 The computing unit of AGC consists of 11 instructions and 16 bit word logic.

 It used 5000 ICs.
 The UI of AGC is known DSKY(display/keyboard) which resembles a calculator
type keypad with array of numerals.
 The first mass-produced embedded system was guidance computer for the
Minuteman-I missile in 1961.
 In the year 1971 Intel introduced the world’s first microprocessor chip called the
4004, was designed for use in business calculators. It was produced by the
Japanese company Busicom.
1.3 EMBEDDED SYSTEM & GENERAL PURPOSE
COMPUTER
The Embedded System and the General purpose computer are at two
extremes. The embedded system is designed to perform a specific task
whereas as per definition the general purpose computer is meant for
general use. It can be used for playing games, watching movies, creating
software, work on documents or spreadsheets etc.
Following are certain specific points of difference between
embedded systems and general purpose computers:
Criteria General Purpose
Computer
Embedded system
Contents It is combination of
generic hardware and a
general purpose OS for
executing a variety of
applications.
It is combination of special
purpose hardware and
embedded OS for executing
specific set of applications
Operating
System
It contains general
purpose operating system
It may or may not contain
operating system.
Alterations Applications are alterable
by the user.
Applications are non-alterable
by the user.
Key factor Performan ce” is key
factor.
Application specific
requirements are key factors.
Power
Consumpti
on
More Less
Response
Time
Not Critical Critical for some
applications

1.4 CLASSIFICATION OF EMBEDDED SYSTEM
The classification of embedded system is based on following criteria’s:
 On generation
 On complexity & performance
 On deterministic behaviour
 On triggering
1.5.1 On generation
1. First generation(1G):
 Built around 8bit microprocessor & microcontroller.
 Simple in hardware circuit & firmware developed.
 Examples: Digital telephone keypads.
2. Second generation(2G):
 Built around 16-bit μp & 8-bit μc.
 They are more complex & powerful than 1G μp & μc.
 Examples: SCADA systems
3. Third generation(3G):
 Concepts like Digital Signal Processors(DSPs),
Application Specific Integrated Circuits(ASICs) evolved.
 Examples: Robotics, Media, etc.
4. Fourth generation:
 The concept of System on Chips (SoC), Multicore
Processors evolved.
 Highly complex & very powerful.
 Examples: Smart Phones.
1.5.2 On complexity & performance
1. Small-scale:
 Simple in application need
 Performance not time-critical.
 Built around low performance & low cost 8 or 16 bit μp/μc.
 Example: an electronic toy
2. Medium-scale:
 Slightly complex in hardware & firmware requirement.
 Built around medium performance & low cost 16 or 32 bit μp/μc.
 Usually contain operating system.
 Examples: Industrial machines.
3. Large-scale:
 Highly complex hardware & firmware.
 Built around 32 or 64 bit RISC μp/μc or PLDs or Multicore
Processors.
 Response is time-critical. Examples: Mission critical applications.

1.5.3 On deterministic behaviour
 This classification is applicable for “Real Time” systems.
 The task execution behaviour for an embedded system may be
deterministic or non-deterministic.
 Based on execution behaviour Real Time embedded systems
are divided into Hard and Soft.
1.5.4 On triggering
 Embedded systems which are “Reactive” in nature can be based
on triggering.
 Reactive systems can be:
 Event triggered
 Time triggered
1.6 APPLICATION OF EMBEDDED SYSTEM
The application areas and the products in the embedded domain are
countless.
1. Consumer Electronics: Camcorders, Cameras.
2. Household appliances: Washing machine, Refrigerator.
3. Automotive industry: Anti-lock breaking system(ABS), engine control.
4. Home automation & security systems: Air conditioners, sprinklers,
fire alarms.
5. Telecom: Cellular phones, telephone switches.
6. Computer peripherals: Printers, scanners.
7. Computer networking systems: Network routers and switches.
8. Healthcare: EEG, ECG machines.
9. Banking & Retail: Automatic teller machines, point of sales.
10. Card Readers: Barcode, smart card readers.
1.7 PURPOSE OF EMBEDDED SYSTEM
1. Data Collection/Storage/Representation
 Embedded system designed for the purpose of data collection performs
acquisition of data from the external world.
 Data collection is usually done for storage,analysis,
manipulation and transmission.
 Data can be analog or digital.
 Embedded systems with analog data capturing techniques collect
data directly in the form of analog signal whereas embedded
systems with digital data collection mechanism converts the analog
signal to the digital signal using analog to digital converters.
 If the data is digital it can be directly captured by digital embedded
system.
 A digital camera is a typical example of an embedded
 System with data collection/storage/representation of data.
 Images are captured and the captured image may be stored within the
memory of the camera. The captured image can also be presented to
the user through a graphic LCD unit.

2. Data communication
 Embedded data communication systems are deployed in applications
from complex satellite communication to simple home networking
systems.
 The transmission of data is achieved either by a wire-line medium or
by a wire-less medium.
 Data can either be transmitted by analog means or by digital means.
 Wireless modules-Bluetooth, Wi-Fi.
 Wire-line modules-USB, TCP/IP.
 Network hubs, routers, switches are examples of dedicated data
transmission embedded systems.
3. Data signal processing
 Embedded systems with signal processing functionalities are employed
in applications demanding signal processing like speech coding,
audio video codec, transmission applications etc.
 A digital hearing aid is a typical example of an embedded system
employing data processing.
 Digital hearing aid improves the hearing capacity of hearing impaired
person
4. Monitoring
 All embedded products coming under the medical domain are with
monitoring functions.
 Electro cardiogram machine is intended to do the monitoring of the
heartbeat of a patient but it cannot impose control over the heartbeat.
 Other examples with monitoring function are digital CRO, digital multi-meters,
and logic analyzers.
5. Control
 A system with control functionality contains both sensors and actuators.
 Sensors are connected to the input port for capturing the changes
in environmental variable and the actuators connected to the output
port are controlled according to the changes in the input variable.
 Air conditioner system used to control the room temperature to a
specified limit is a typical example for CONTROL purpose.
6. Application specific user interface
 Buttons, switches, keypad, lights, bells, display units etc are
application specific user interfaces.
 Mobile phone is an example of application specific user interface.
 In mobile phone the user interface is provided through the keypad,
system speaker, vibration alert etc.

1.8 REVIEW QUESTIONS
1. Define Embedded System with the help of Microwave Owen as an
example
2. Differentiate between general purpose computers &
embedded systems
3. Give a classification of embedded systems
4. List some applications of embedded systems
5. Explain the various possible purposes of using and
embedded system.


ELEMENTS OF EMBEDDED SYSTEMS
3.1 ELEMENTS OF EMBEDDED SYSTEMS.
 As defined earlier, an embedded system is a combination of 3 things:
d. Hardware
e. Software
f. Mechanical Components
And it is supposed to do one specific task only.
Diagrammatically an embedded system can be represented as
follows:
Figure 2.0 : Elements of an Embedded System
 Embedded systems are basically designed to regulate a physical
variable (such Microwave Oven) or to manipulate the state of some
devices by sending some signals to the actuators or devices connected
to the output port system (such as temperature in Air Conditioner), in
response to the input signal provided by the end users or sensors
which are connected to the input ports.
 Hence the embedded systems can be viewed as a reactive system.
 Examples of common user interface input devices are keyboards, push
button, switches, etc.
 The memory of the system is responsible for holding the code (control
algorithm and other important configuration details).
 An embedded system without code (i.e. the control algorithm)
implemented memory has all the peripherals but is not capable of
making decisions depending on the situational as well as real world
changes.
 Memory for implementing the code may be present on the processor or
may be implemented as a separate chip interfacing the processor In a
controller based embedded system, the controller may contain internal
memory for storing code
 Such controllers are called Micro-controllers with on-chip ROM, eg.
Atmel AT89C51.

2.3 CASE STUDIES (EXAMPLES)
Here are some case studies on some commonly used
embedded systems that will help to better understand the
concept.
2.3.1 Washing Machine
Let us see the important parts of the washing machine; this will
also help us understand the working of the washing machine:
1) Water inlet control valve: Near the water inlet point of the
washing there is water inlet control valve. When you load the
clothes in washing machine, this valve gets opened
automatically and it closes automatically depending on the total
quantity of the water required. The water control valve is actually
the solenoid valve.
2) Water pump: The water pump circulates water through the
washing machine. It works in two directions, re-circulating the
water during wash cycle and draining the water during the spin
cycle.
Figure 2.1 : Parts of a Washing
Machine

3) Tub: There are two types of tubs in the washing washing machine:
inner and outer. The clothes are loaded in the inner tub, where
the clothes are washed, rinsed and dried. The inner tub has small
holes for draining the water. The external tub covers theinner
tub and supports it during various cycles of clothes washing.
4) Agitator or rotating disc: The agitator is located inside the tub of
the washing machine. It is the important part of the washing
machine that actually performs the cleaning operation of the
clothes. During the wash cycle the agitator rotates continuously and
produces strong rotating currents within the water due to which
the clothes also rotate inside the tub. The rotation of the clothes
within water containing the detergent enables the removal of the
dirt particles from the fabric of the clothes. Thus the agitator
produces most important function of rubbing the clothes with each
other as well as with water.
In some washing machines, instead of the long agitator, there is a
disc that contains blades on its upper side. The rotation of the
disc and the blades produce strong currents within the water
and the rubbing of clothes that helps in removing the dirt from
clothes.
5) Motor of the washing machine: The motor is coupled to the
agitator or the disc and produces it rotator motion. These are
multispeed motors, whose speed can be changed as per the
requirement. In the fully automatic washing machine the speed of
the motor i.e. the agitator changes automatically as per the load
on the washing machine.
6) Timer: The timer helps setting the wash time for the clothes
manually. In the automatic mode the time is set automatically
depending upon the number of clothes inside the washing machine.
7) Printed circuit board (PCB): The PCB comprises of the various
electronic components and circuits, which are programmed to
perform in unique ways depending on the load conditions (the
condition and the amount of clothes loaded in the washing
machine). They are sort of artificial intelligence devices that
sense the various external conditions and take the decisions
accordingly. These are also called as fuzzy logic systems. Thus the
PCB will calculate the total weight of the clothes, and find out the
quantity of water and detergent required, and the total time
required for washing the clothes. Then they will decide the time
required for washing and rinsing. The entire processing is done on
a kind of processor which may be a microprocessor or
microcontroller.
8) Drain pipe: The drain pipe enables removing the dirty water
from the washing that has been used for the washing purpose.

2.3.2 Microwave Owen
Let us see the important parts of the microwave oven; this will
also help us understand the working of the washing machine:
Figure 2.3 : Parts of a Microwave Owen
A microwave oven consists of:
1. A high voltage transformer, which passes energy to the
magnetron
2. A cavity magnetron,
3. A Control circuit with a microcontroller,
4. A waveguide, and
5. A cooking chamber
1. A Transformer transfers electrical energy through a circuit by
magnetic coupling without using motion between parts. These are
used for supplying power to the magnetron.
2. A Cavity magnetron is a microwave antenna placed in a vacuum
tube and oscillated in an electromagnetic field in order to produce
high GHz microwaves. Magnetrons are used in microwave ovens and
radar systems.
3. A control circuit with a microcontroller is integrated on a circuit board.
The microcontroller controls the waveguide and the entire unit so the
microwaves are emitted at a constant rate.
4. A Waveguide is any linear structure that guides electromagnetic
waves for the purpose of transmitting power or signals.
Generally constructed of a hollow metal pipe. Placing a
waveguide into a vacuum causes radio waves to scatter.
5. A Cooking Chamber is a microwave safe container the prevents
microwaves from escaping. The door has a microwave proof mesh

with holes that are just small enough that microwaves can’t pass
through but lightwaves can. The cooking chamber itself is a Faraday
cage enclosure which prevents the microwaves from escaping into the
environment. The oven door is usually a glass panel for easy
viewing, but has a layer of conductive mesh to maintain the shielding.
2.3.3 Automotive Embedded System (AES)
 The Automotive industry is one of the major application domains of
embedded systems.
 Automotive embedded systems are the one where electronics take
control over the mechanical system. Ex. Simple viper control.
 The number of embedded controllers in a normal vehicle varies
somewhere between 20 to 40 and can easily be between 75 to 100
for more sophisticated vehicles.
 One of the first and very popular use of embedded system in
automotive industry was microprocessor based fuel injection.
 Some of the other uses of embedded controllers in a vehicle are
listed below:
a. Air Conditioner
b. Engine Control
c. Fan Control
d. Headlamp Control
e. Automatic break system control
f. Wiper control
g. Air bag control
h. Power Windows
 AES are normally built around microcontrollers or DSPs or a hybrid
of the two and are generally known as Electronic Control Units
(ECUs).
 Types Of Electronic Control Units(ECU)
1. High-speed Electronic Control Units (HECUs):
a. HECUs are deployed in critical control units requiring fast
response.
b. They Include fuel injection systems, antilock brake systems,
engine control, electronic throttle, steering controls,
transmission control and central control units.
2. Low Speed Electronic Control Units (LECUs):-
a. They are deployed in applications where response
time is not so critical.
b. They are built around low cost microprocessors and
microcontrollers and digital signal processors.
c. Audio controller, passenger and driver door locks, door glass
control etc.

 Automotive Communication Buses
Embedded system used inside an automobile communicate
with each other using serial buses. This reduces the wiring
required.
Following are the different types of serial Interfaces used in
automotive embedded applications:
a. Controller Area Network (CAN):-
 CAN bus was originally proposed by Robert Bosch.
 It supports medium speed and high speed data transfer
 CAN is an event driven protocol interface with support for
error handling in data transmission.
b. Local Interconnect Network (LIN):-
 LIN bus is single master multiple slave communication
interface with support for data rates up to 20 Kbps
and is used for sensor/actuator interfacing
 LIN bus follows the master communication triggering
to eliminate the bus arbitration problem
 LIN bus applications are mirror controls , fan controls
, seat positioning controls
c. Media-Oriented System Transport(MOST):-
 MOST is targeted for automotive audio/video
equipment interfacing
 A MOST bus is a multimedia fiber optics point–to-point
network implemented in a star , ring or daisy
chained topology over optical fiber cables.
 MOST bus specifications define the physical as well as
application layer , network layer and media access
control.
1. What is an embedded system? What are the working
elements of an embedded system?
2. Explain the working of embedded system with respect to:
B. Washing Machine
C. MICROWAVE Owen
3. Conduct case studies for working of embedded systems for
the following topics:
A. Air Conditioner
B. Automobile

CORE THE OF EMBEDDED SYSTEM
3.1 INTRODUCTION
The first two chapters attempted on explain what an
embedded system is about and what the working parts are. This
chapter attempts to go deeper and explain the core of embedded
system along with other related topics.
3.2 CORE OF EMBEDDED SYSTEMS
Embedded systems are domain and application specific
and are built around a central core. The core of the embedded
system falls into any of the following categories:
1. General purpose and Domain Specific Processors
1.1. Microprocessors
1.2. Microcontrollers
1.3. Digital Signal Processors
2. Application Specific Integrated Circuits. (ASIC)
3. Programmable logic devices(PLD’s)
4. Commercial off-the-shelf components (COTs)
3.2.1 GENERAL PURPOSE AND DOMAIN SPECIFIC
PROCESSOR.
• Almost 80% of the embedded systems are processor/
controller based.
• The processor may be microprocessor or a microcontroller or
digital signal processor, depending on the domain and
application.
3.2.1.1 MICROPROCESSORS
 A microprocessor is a silicon chip representing a central processing
unit.
 A microprocessor is a dependent unit and it requires the combination
of other hardware like memory, timer unit, and interrupt controller, etc.
for proper functioning.
 Developers of microprocessors.
o Intel – Intel 4004 – November 1971(4-bit).
o Intel – Intel 4040.
o Intel – Intel 8008 – April 1972.
o Intel – Intel 8080 – April 1974(8-bit).
o Motorola – Motorola 6800. o
Intel – Intel 8085 – 1976. o
Zilog - Z80 – July 1976.

 Architectures used for processor design are Harvard or Von-
Neumann.
Harvard architecture Von-Neumann architecture
It has separate buses for
instruction as well as data
fetching.
Easier to pipeline, so high
performance can be achieve.

Comparatively high cost.

Since data memory and
program memory are stored
physically in different locations,
no chances exist for accidental
corruption of program memory.
It shares single common bus
for instruction and data
fetching.
Low performance as
compared to Harvard
architecture.

 It is cheaper.

Accidental corruption of
program memory may occur if
data memory and program
memory are stored physically
in the same chip,

 RISC and CISC are the two common Instruction Set
Architectures (ISA) available for processor design.
RISC CISC
Reduced Instruction Set
Computing
It contains lesser number of
instructions.
Instruction pipelining and
increased execution speed.
Orthogonal instruction
set(allows each instruction to
operate on any register and
use any addressing mode.

Operations are performed on
registers only, only memory
operations are load and store.

A larger number of registers
are available.
Programmer needs to write
more code to execute a task
since instructions are simpler
ones.
It is single, fixed length
instruction.
Less silicon usage and
pin count.

With Harvard Architecture.
Complex Instruction Set
Computing
It contains greater number
of instructions.
Instruction pipelining feature
does not exist.
Non-orthogonalset(all
instructions are not allowed
to operate on any register
and use any addressing
mode.
Operations are performed
either on registers or
memory depending on
instruction.
The number of general
purpose registers are very
limited.
Instructions are like
macros in C language. A
programmer can achieve
the desired functionality with
a single instruction which in
turn provides the effect of
using more simpler single
instruction in RISC.
It is variable length
instruction.

More silicon usage since
more additional decoder
logic is required to
implement the complex
instruction decoding.
Can be Harvard or Von-
Neumann Architecture.
3.2.1.2 MICROCONTROLLERS.
 A microcontroller is a highly integrated chip that contains a
CPU, scratch pad RAM, special and general purpose register
arrays,on chip ROM/FLASH memory for program storage ,

timer and interrupt control units and dedicated I/O ports.
 Texas Instrument’s TMS 1000 Is considered as the world’s first
microcontroller.
 Some embedded system application require only 8 bit
controllers whereas some requiring superior performance and
computational needs demand 16/32 bit controllers.
 The instruction set of a microcontroller can be RISC or
CISC.
 Microcontrollers are designed for either general purpose
application requirement or domain specific application
requirement.
3.2.1.3 Digital Signal Processors
 DSP are powerful special purpose 8/16/32 bit microprocessor
designed to meet the computational demands and power
constraints of today’s embedded audio, video and
communication applications.
 DSP are 2 to 3 times faster than general purpose
microprocessors in signal processing applications. This is
because of the architectural difference between DSP and
general purpose microprocessors.
 DSPs implement algorithms in hardware which speeds up the
execution whereas general purpose processor implement the
algorithm in software and the speed of execution depends
primarily on the clock for the processors.
 DSP includes following key units:
i. Program memory: It is a memory for storing the program
required by DSP to process the data.
ii. Data memory: It is a working memory for storing
temporary variables and data/signal to be processed.
iii. Computational engine: It performs the signal processing in
accordance with the stored program memory computational
engine incorporated many specialized arithmetic units and
each of them operates simultaneously to increase the
execution speed. It also includes multiple hardware shifters
for shifting operands and saves execution time.
iv. I/O unit: It acts as an interface between the outside world
and DSP. It is responsible for capturing signals to be
processed and delivering the processed signals.
 Examples: Audio video signal processing,
telecommunication and multimedia applications.
 SOP(Sum of Products) calculation, convolution, FFT(Fast
Fourier Transform), DFT(Discrete Fourier Transform),
etc are some of the operation performed by DSP.

3.2.2 Application Specific Integrated Circuits. (ASIC)
 ASICs is a microchip design to perform a specific and
unique applications.
 Because of using single chip for integrates several
functions there by reduces the system development cost.
 Most of the ASICs are proprietary (which having some
trade name) products, it is referred as Application
Specific Standard Products(ASSP).
 As a single chip ASIC consumes a very small area in the
total system. Thereby helps in the design of smaller
system with high capabilities or functionalities.
 The developers of such chips may not be interested in
revealing the internal detail of it .
3.2.3 Programmable logic devices(PLD’s)
 A PLD is an electronic component. It used to build digital
circuits which are reconfigurable.
 A logic gate has a fixed function but a PLD does not have a
defined function at the time of manufacture.
 PLDs offer customers a wide range of logic capacity,
features, speed, voltage characteristics.
 PLDs can be reconfigured to perform any number of
functions at any time.
 A variety of tools are available for the designers of PLDs
which are inexpensive and help to develop, simulate and
test the designs.
 PLDs having following two major types.
1) CPLD(Complex Programmable Logic Device):
CPLDs offer much smaller amount of logic up to 1000
gates.
2) FPGAs(Field Programmable Gate Arrays):
It offers highest amount of performance as well as
highest logic density, the most features.
 Advantages of PLDs :-
1) PLDs offer customer much more flexibility during the
design cycle.
2) PLDs do not require long lead times for prototypes or

production parts because PLDs are already on a
distributors shelf and ready for shipment.
3) PLDs can be reprogrammed even after a piece of
equipment is shipped to a customer
3.2.4 Commercial off-the-shelf components(COTs)
1) A Commercial off the Shelf product is one which is used ’as- is’.
2) The COTS components itself may be develop around a general
purpose or domain specific processor or an ASICs or a PLDs.
3) The major advantage of using COTS is that they are readily
available in the market, are chip and a developer can cut
down his/her development time to a great extent
4) The major drawback of using COTS components in embedded
design is that the manufacturer of the COTS component may
withdraw the product or discontinue the production of the COTS
at any time if rapid change in technology occurs.
5) Advantages of COTS:
1) Ready to use
2) Easy to integrate
3) Reduces development time
6) Disadvantages of COTS:
1) No operational or manufacturing standard (all
proprietary)
2) Vendor or manufacturer may discontinue production
of a particular COTS product

3.3 SENSORS & ACTUATORS
 Sensor
 A Sensor is used for taking Input
 It is a transducer that converts energy from one form
to another for any measurement or control purpose
 Ex. A Temperature sensor
 Actuator
 Actuator is used for output.
 It is a transducer that may be either mechanical or
electrical which converts signals to corresponding
physical actions.
 Ex. LED (Light Emitting Diode)
 LED is a p-n junction diode and contains a CATHODE and
ANODE
 For functioning the anode is connected to +ve end of
power supply and cathode is connected to –ve end of
power supply.
 The maximum current flowing through the LED is limited
by connecting a RESISTOR in series between the power
supply and LED as shown in the figure below
 There are two ways to interface an LED to
a microprocessor/microcontroller:
1. The Anode of LED is connected to the port pin
and cathode to Ground : In this approach the port pin
sources the current to the LED when it is at logic high(ie.
1).
2. The Cathode of LED is connected to the port pin
and Anode to Vcc : In this approach the port pin
sources the current to the LED when it is at logic high (ie.
1).
Here the port pin sinks the current and the LED is
turned ON when the port pin is at Logic low (ie. 0)

3.4 COMMUNICATION INTERFACES
For any embedded system, the communication interfaces
can broadly classified into:
1. Onboard Communication Interfaces
 These are used for internal communication of the
embedded system i.e: communication between
different components present on the system.
 Common examples of onboard interfaces are:
 Inter Integrated Circuit (I2C)
 Serial Peripheral Interface (SPI)
 Universal Asynchronous Receiver Transmitter (UART)
 1-Wire Interface
 Parallel Interface
 Example :Inter Integrated Circuit (I2C)
• It is synchronous
• Bi-directional, half duplex , two wire serial interface bus
• Developed by Phillips semiconductors in 1980
• It comprises of two buses :
1. Serial clock –SCL
2. Serial Data – SDA
• SCL generates synchronization clock pulses
• SDA transmits data serially across devices
• I2C is a shared bus system to which many devices
can be connected
• Devices connected by I2C can act as either master
or slave
• The master device is responsible for
controlling communication by initiating/ terminating
data transfer.
• Devices acting as slave wait for commands from
the master and respond to those commands.
Figure: I2C Bus Interfacing

2. External or Peripheral Communication Interfaces
 These are used for external communication of the
embedded system i.e: communication of different
components present on the system with external or
peripheral components/devices.
 Common examples of external interfaces are:
 RS-232 C & RS-485
 Universal Serial Bus (USB)
 IEEE 1394 (Firewire)
 Infrared (IrDA)
 Bluetooth
 Wi-Fi
 Zig Bee
 General Packet Radio Service (GPRS)
 Example: RS-232 C & RS-485
 It is wired, asynchronous, serial, full
duplex communication
 RS 232 interface was developed by EIA
(Electronic Industries Associates) In early 1960s
 RS 232 is the extension to UART for
external communications
 RS-232 logic levels use:
 +3 to +25 volts to signify a "Space" (Logic 0) and
 -3 to -25 volts to signify a "Mark" (logic 1).
 RS 232 supports two different types of connectors :
 DB 9 and DB 25 as shown in figure below
 RS 232 interface is a point to point communication
interface and the devices involved are called as
Data Terminating Equipment (DTE) And Data
Communications Terminating Equipment (DCE)
 Embedded devices contain UART for serial
transmission and generate signal levels as per
TTL/CMOS logic.
 A level translator IC (like Max 232) is used for
converting the signal lines from UART to RS 232
signal lines for communication.
 The vice versa is performed on the receiving side.
 Converter chips contain converters for both
transmitters and receivers
 RS 232 is used only for point to point connections

 It is susceptible to noise and hence is limited to
short distances only
 RS 422 is another serial interface from EIA.
 It supports multipoint connections with 1 transmitter
and 10 receivers.
 It supports data rates up to 100Kbps and distance up
to 400 ft
 RS 485 is enhanced version of RS 422 and supports
up to 32 transmitters and 32 receivers
1. What do you mean by core of the embedded system?
What is its significance? What are the possible options that
can be used as a core?
2. Distinguish between Microprocessor & Microcontroller
3. Explain the different types of processors according to
their system bus architecture
4. Explain the different types of processors according to
Instruction set Architecture
5. Explain the different types of processors according to Endianness
6. Write short note on :
i. DSP
ii. PLD
iii. ASIC
iv. COTS
7. Explain Communication Interfaces with respect to
embedded system
8. Explain the following with example:
1. Onboard communication interface
2. Peripheral communication interface
9. Find out information and write case studies on the
following communication interfaces:
i. Infrared
ii. WiFi
iii. Zigbee
iv. UART


CHARACTERISTICS & QUALITY
ATTRIBUTES OF EMBEDDED SYSTEMS
4.1 CHARACTERISTICS OF EMBEDDED SYSTEM
Following are some of the characteristics of an
embedded system that make it different from a general
purpose computer:
1. Application and Domain specific
 An embedded system is designed for a specific purpose
only. It will not do any other task.
 Ex. A washing machine can only wash, it cannot cook
 Certain embedded systems are specific to a domain: ex. A
hearing aid is an application that belongs to the domain of
signal processing.
2. Reactive and Real time
 Certain Embedded systems are designed to react to the
events that occur in the nearby environment. These events
also occur real-time.
 Ex. An air conditioner adjusts its mechanical parts as soon as
it gets a signal from its sensors to increase or decrease the
temperature when the user operates it using a remote control.
 An embedded system uses Sensors to take inputs and has
actuators to bring out the required functionality.
3. Operation in harsh environment
 Certain embedded systems are designed to operate in harsh
environments like very high temperature of the deserts or
very low temperature of the mountains or extreme rains.
 These embedded systems have to be capable of sustaining the
environmental conditions it is designed to operate in.
4. Distributed
 Certain embedded systems are part of a larger system and
thus form components of a distributed system.
 These components are independent of each other but have to
work together for the larger system to function properly.
 Ex. A car has many embedded systems controlled to its
dash board. Each one is an independent embedded system yet
the entire car can be said to function properly only if all the
systems work together.
5. Small size and weight
 An embedded system that is compact in size and has light
weight will be desirable or more popular than one that is
bulky and heavy.
 Ex. Currently available cell phones. The cell phones that
have the maximum features are popular but also their size and
weight is an important characteristic.
 For convenience users prefer mobile phones than phablets.
(phone + tablet pc)

6. Power concerns
 It is desirable that the power utilization and heat dissipation of
any embedded system be low.
 If more heat is dissipated then additional units like heat sinks or
cooling fans need to be added to the circuit.
 If more power is required then a battery of higher power or
more batteries need to be accommodated in the embedded
system.
4.2 QUALITY ATTRIBUTES OF
EMBEDDED SYSTEM
These are the attributes that together form the
deciding factor about the quality of an embedded system.
There are two types of quality attributes are:-
1. Operational Quality Attributes.
 These are attributes related to operation or functioning of an
embedded system. The way an embedded system operates
affects its overall quality.
2. Non-Operational Quality Attributes.
 These are attributes not related to operation or functioning of
an embedded system. The way an embedded system
operates affects its overall quality.
 These are the attributes that are associated with the
embedded system before it can be put in operation.
4.3.1 Operational Attributes
a) Response
 Response is a measure of quickness of the system.
 It gives you an idea about how fast your system is tracking
the input variables.
 Most of the embedded system demand fast response
which should be real-time.
b) Throughput
 Throughput deals with the efficiency of system.
 It can be defined as rate of production or process of a
defined process over a stated period of time.
 In case of card reader like the ones used in buses,
throughput means how much transaction the reader can
perform in a minute or hour or day.
c) Reliability
 Reliability is a measure of how much percentage you rely
upon the proper functioning of the system .
 Mean Time between failures and Mean Time To Repair are
terms used in defining system reliability

.
 Mean Time between failures can be defined as the average
time the system is functioning before a failure occurs.
 Mean time to repair can be defined as the average time the
system has spent in repairs.
d) Maintainability
 Maintainability deals with support and maintenance to the end
user or a client in case of technical issues and product
failures or on the basis of a routine system checkup
 It can be classified into two types :-
1. Scheduled or Periodic Maintenance
o This is the maintenance that is
required regularly after a periodic time interval.
o Example :
 Periodic Cleaning of Air Conditioners
 Refilling of printer cartridges.
2. Maintenance to unexpected failure
 This involves the maintenance due to a sudden breakdown in
the functioning of the system.
 Example:
1. Air conditioner not powering on
2. Printer not taking paper in spite of a full paper stack
e) Security
 stones of information security.Confidentiality, Integrity
and Availability are three corner
 Confidentiality deals with protection data from
unauthorized disclosure.
 Integrity gives protection from unauthorized modification.
 Availability gives protection from unauthorized user
 Certain Embedded systems have to make sure they
conform to the security measures. Ex. An Electronic
Safety Deposit Locker can be used only with a pin
number like a password.
f) Safety
 Safety deals with the possible damage that can happen
to the operating person and environment due to the
breakdown of an embedded system or due to the
emission of hazardous materials from the embedded
products.
 A safety analysis is a must in product engineering to
evaluate the anticipated damage and determine the best
course of action to bring down the consequence of damages
to an acceptable level.

4.3.2 Non Operational Attributes
a) Testability and Debug-ability
 It deals with how easily one can test his/her design,
application and by which mean he/she can test it.
 In hardware testing the peripherals and total hardware
function in designed manner
 Firmware testing is functioning in expected way
 Debug-ability is means of debugging the product as such
for figuring out the probable sources that create
unexpected behavior in the total system
b) Evolvability
 For embedded system, the qualitative attribute
“Evolvability” refer to ease with which the embedded
product can be modified to take advantage of new
firmware or hardware technology.
c) Portability
 Portability is measured of “system Independence”.
 An embedded product can be called portable if it is
capable of performing its operation as it is intended to
do in various environments irrespective of different
processor and or controller and embedded operating
systems.
d) Time to prototype and market
 Time to Market is the time elapsed between the
conceptualization of a product and time at which the
product is ready for selling or use
 Product prototyping help in reducing time to market.
 Prototyping is an informal kind of rapid product
development in which important feature of the under
consider are develop.
 In order to shorten the time to prototype, make use of
all possible option like use of reuse, off the self
component etc.
e) Per unit and total cost
 Cost is an important factor which needs to be carefully
monitored. Proper market study and cost benefit
analysis should be carried out before taking decision on
the per unit cost of the embedded product.
 When the product is introduced in the market, for the
initial period the sales and revenue will be low
 There won’t be much competition when the product
sales and revenue increase.

EMBEDDED HARDWARE
FROM SOFTWARE
PROGRAMMERS
PERSPECTIVE
7.1 COMPONENTS ON AN EMBEDDED SYSTEM
 Before the programmer can start to code anything, he has
to invest some time in understand the functioning of the
embedded system.
 He is expected to understand the following things:
a. Functioning or purpose of the embedded system
b. Individual components involved
c. The way data flows through the components of
an embedded system.
 Consider an example of an embedded system intended
to be used as a printer-sharing device. This device is
attached to a printer and allows access to two computers
through serial interface and one printer through a parallel
interface.
 The diagram below describes the way the devices are
connected to each other. Data to be printed is accepted from
either serial port, held in RAM until the printer is ready for more
data, and delivered to the printer via the parallel port. The
software that makes all of this happen is stored in ROM.
 The working or execution of the code is brought about by
the processor. The processor knows two types of components:
memory and peripherals.
 Memories are for data and code storage and retrieval.
Ex. RAM & ROM
 Peripherals are specialized hardware devices that either
coordinate interaction with the outside world (I/O) or perform
a specific hardware function. Ex. Serial Port

Figure: Components involved in an printer sharing device
 Certain processors like intel communicate with these
memories and peripherals with two distinct address spaces.
 The first address space is called the memory space
and is intended mainly for memory devices; the second is
reserved exclusively for peripherals and is called the I/O
space.
 When peripherals are located in I/O space they are
called I/O Mapped peripheral else when peripherals are
located in memory space they are called Memory Mapped
peripherals or memory mapped I/O.
 If given a choice, Memory mapped peripherals are
better because it has advantages for both the hardware
and software developers. It is attractive to the hardware
developer because he might be able to eliminate the I/O
space, and some of its associated wires, altogether. It is
attractive to the software developer who is able to use
pointers, data structures, and unions to interact with the
peripherals more easily and efficiently

Embedded System

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Embedded System (20)

More from Sonali Parab (19)

Recently uploaded (20)

Embedded System