Improving color rendering index of WLEDs with convex-dual-layer remote phosphor geometry using red-emitting CaGa2S4:Mn2+ phosphor

TELKOMNIKA Telecommunication, Computing, Electronics and Control
Vol. 18, No. 5, October 2020, pp. 2702~2707
ISSN: 1693-6930, accredited First Grade by Kemenristekdikti, Decree No: 21/E/KPT/2018
DOI: 10.12928/TELKOMNIKA.v18i5.14250  2702
Journal homepage: http://journal.uad.ac.id/index.php/TELKOMNIKA
Improving color rendering index of WLEDs with
convex-dual-layer remote phosphor geometry using
red-emitting CaGa2S4:Mn2+
phosphor
Nguyen Thi Phuong Loan1
, Anh Tuan Le2
1
Faculty of Fundamental 2, Posts and Telecommunications Institute of Technology, Vietnam
2
Faculty of Electrical and Electronics Engineering, Ton DucThang University, Vietnam
Article Info ABSTRACT
Article history:
Received Oct 2, 2019
Revised Apr 9, 2020
Accepted May 14, 2020
The white-light light-emitting diode (LED), a conventional illumination
solution, usually consists of one chip and one phosphor layer, which leads to
the insufficient color rendering index (CRI) in this configuration. To optimize
the efficiency of WLED, a new LED package with 2 chips and one phosphor
was proposed, this innovative configuration can yield more lights and achieve
high CRI. Thus, this study aims at perfecting the color performance with
the two chips and dual phosphor layers package with the proportions and
densities of phosphor in the silicone constantly changed to find the best option.
The white-light LED module is adjusted using a specialized color design
model. The comparison results between the measured and the simulation from
the color design model CIE 1931 color coordinates suggest that the highest
discrepancy is about 0.0063 and is achieved at around 5600 K correlated color
temperature (CCT). This study’s results lay a firm path in customizing
white-light LED modules that guarantee CRI and lumen output qualities.
Keywords:
CaGa2S4:Mn2+
Color rendering index
Dual-layer remote phosphor
geometry
Mie-scattering theory
WLEDs
This is an open access article under the CC BY-SA license.
Corresponding Author:
Anh Tuan Le,
Faculty of Electrical and Electronics Engineering,
Ton DucThang University,
Ho Chi Minh City, Vietnam.
Email: leanhtuan1@tdtu.edu.vn
1. INTRODUCTION
The white-light light-emitting diode (LED) is one of the most frequently used lighting methods in this
industry. The fact that LEDs have so many remarkable traits such as high durability, good endurance against
impacts, power saving, waste-free, and compact design allowing them to be used in many occasions from
indoor lighting to lighting in tough condition as street lighting. The recent advancement in fast-switch brought
even more attention as they are now also used in smart lighting, an auto lighting technology. To assess
the lighting performance of LED, color rendering index (CRI), which is used to evaluate the LED light quality
by comparing the light source from LED to the natural light or black-body radiation, is considered as a vital
indicator. The result of CRI reflects the light quality of that LED, if the emission spectrum of phosphor in
the LED resembling the broad continuous spectrum of black-body radiation, the CRI is high and so does
the light quality [1-3]. For the construction of a white-light emitting structure with LED chips and phosphor,
many approaches are suggested. However, the configuration containing one blue chip and a layer of yellow
phosphor is the most popular method for cheap production cost [4, 5]. This configuration is discovered early
on and the setting is not optimal, therefore, the CRI is still low although many efforts have been made to

TELKOMNIKA Telecommun Comput El Control 
Improving color rendering index of WLEDs with… (Nguyen Thi Phuong Loan)
2703
enhance it such as using the chips emitting red and blue light with a yellow phosphor film. There are reports
on instances that combination of phosphors and LED chips can adjust the emission spectrum to the desired
value, thus, allowing the color quality and CRI to be set to the highest. The spectra of LED and phosphor with
empirical and mathematical structures are analyzed to get the information that can help tuning the light color
and changing CRI [6-8]. The obstacle with customized white LEDs that has adjustable correlated color
temperatures (CCTs) is achieving high CRI while maintaining high luminous efficiency. This due to
the package using a blue LED chip and two phosphor layers possibly attains great CRI values, yet the lumen
output is inferior owing to the Stokes shift. On the other hand, though the package of single-layer phosphor
with blue and red LED chips has both CRI and lumen efficacy, it is unable to adjust the color as the dual-layer
phosphor structure does [9-12]. This leads to the solution of using the package with two LEDs and two
phosphors for high CRI, yielded luminous flux and color tenability. In this research paper, based on Beer’s law
and linear conversion used for the subtle color difference production demands of white-light LEDs (WLED),
a color design model is demonstrated. The WLED packages used for carried out the experiments are from
yttrium aluminum garnet (YAG) and nitride-based phosphors in blue and red LEDs having good CRI and
lumen efficacy. The different phosphor proportions and densities are used with silicone contains two types of
LEDs to create the white LEDs. The obtained results show that the color design module suggested above is
efficient and easy to fabricate.
2. PREPARATION AND SIMULATION
2.1. Preparation
CaGa2S4:Mn2+
phosphor is used for the experiments in this study, the composition of CaGa2S4:Mn2+
consists of 98% CaCO3, 2% MnCO3, and 200 (of Ga) Ga2O3, and each component weighs 98 g, 2.3 g and
187 g, respectively [13-15]. To fabricate the red phosphor CaGa2S4:Mn2+
, there is a 5-step procedure that needs
to be follow strictly to ensure the success and the quality of the product. The first step is to mix the ingredients
by slurrying in water, stop when the compound is mixed evenly. The next step is to leave the mixture in airy
condition and let it dry. Then, grind the dehydrated mixture to get the powder. Next, put the powder from
the previous step in open quartz boats, place it into a furnace with H2S, at 900ºC, and fire for 2 hours. When
the firing process is done, take it out and begin to powderize. In the fourth step, place the compound in open
quartz boats and put it through firing process again; this time fire at 800ºC with N2 loaded with CS2 in 1 hour.
The final step is storing the final product in a well-sealed container. The red phosphor CaGa2S4:Mn2+
that come
out of the process exhibits a deep red emission color and discharge the emission peak of 1.74 eV.
2.2. Simulation
The LightTools program is the essential tool to create the simulation of the LED and the Mie-theory
is used to verify the accuracy of the results [16-19]. The simulation of the WLEDs with dual-layer phosphor
can be proceeded after the parameters about the scattering properties of phosphor particles are gathered.
Moreover, these information also assist the study of CaGa2S4:Mn2+
phosphor’s influence on WLEDs at a high
correlated temperature of 5600 K. Figure 1 demonstrates how the compound of CaGa2S4:Mn2+
and YAG:Ce3+
phosphor is prepared to create the in-cup phosphor configuration of WLEDs. As can be seen, the order in which
the phosphor layers are placed is CaGa2S4:Mn2+
phosphor, the yellow phosphor YAG:Ce3+
, and the silicone
glues. The WLEDs model illustrated in Figure 1 consists of a reflector cup, a silicone film, nine blue chips,
and two phosphor layers. The parameters of the reflector that cover the chips are 2.07 mm depth, 8 mm bottom
length, and 9.85 mm top surface length. Each of the 9 blue chips has the emission power of 1.16 W at 453 nm
peak wavelength. The refractive index of CaGa2S4:Mn2+
phosphor is 1.85 and YAG:Ce3+
is 1.83.
The concentration of YAG:Ce3+
has to be changed appropriately to balance with the fluctuation of
CaGa2S4:Mn2+
concentration and keep the average CCTs.
(a) (b) (c) (d)
Figure 1. (a) 3D modelling, (b) bonding diagram, (c) model of pc-WLEDs cross-section,
(d) illustration of WLEDs simulated from LightTools commercial software

 ISSN: 1693-6930
TELKOMNIKA Telecommun Comput El Control, Vol. 18, No. 5, October 2020: 2702 - 2707
2704
3. RESULTS AND DISCUSSION
The changes to be made with YAG:Ce3+
phosphor to keep the average CCTs when CaGa2S4:Mn2+
phosphor increase are shown in Figure 2. In particular, when the concentration of CaGa2S4:Mn2+
is rising from
2-26% wt., the phosphor concentration of YAG:Ce3+
has to decrease accordingly to keep the average CCT,
the tendency is unchanged with WLEDs at the color temperature of 5600K. The changes that are made based
on these results also affect scattering and absorption properties, thus, leading to potential improvements
in WLEDs color quality and light output. Furthermore, the performance of WLEDs is determined
by CaGa2S4:Mn2+
phosphor, so choosing the concentration of this phosphor is very important.
Figure 2. The balance between two phosphor concentrations to keep the average CCT
In Figure 3 are the effects of red phosphor CaGa2S4:Mn2+
in two different concentrations, 2% and 24%,
on emission spectrum of WLEDs. The figure shows the luminous flux from WLED at 5600K ACCT, and
the white light yielded from the spectral regions. The red line increases with the concentration of CaGa2S4:Mn2+
at three different regions: the most notable region is from 648–738 nm, and the other regions are from
420-480 nm and 500-640 nm. The increase in emission spectra from 420–480 nm boosts the scattered blue light.
The results confirm the benefits of CaGa2S4:Mn2+
to the color quality of WLEDs having color temperature of
5600 K. This is an important finding because it helps the manufacturers choose the correct concentration to create
WLEDs that suits their intention. A small disadvantage in WLEDs with high color quality that the manufacturers
need to pay attention to is that the luminous flux of these WLEDs is reduced a bit.
Figure 3. The emission spectra of WLEDs at 5600 K CCTs corresponding to CaGa2S4:Mn2+
concentration
The results from Figure 4 suggest that adding CaGa2S4:Mn2+
phosphor can increase CRI values for
WLEDs. This is because of the absorbing characteristic of red phosphor CaGa2S4:Mn2+
that turns the absorbed
blue light to red light. The red phosphor CaGa2S4:Mn2+
also absorbs yellow light; however, the absorbed blue
light is still dominant due to the characteristic of the phosphor material. As a result, the red-light component in
WLEDs increases when there is red phosphor CaGa2S4:Mn2+
in the package, which is beneficial to the CRI.
Color rendering index is one of the indicators that can evaluate the quality of a WLED, the higher the CRI
the better the quality of WLED and also the higher production cost. However, using CaGa2S4:Mn2+
phosphor
can fix that problem because this is a low-cost method, and thus it allows WLEDs with CaGa2S4:Mn2+
phosphor
to be used commonly. In recent years, CRI is not the most important index when evaluating the color quality
of WLEDs because it is not a very in-depth indicator. Instead, the CQS is the viewed as a more efficient and
accurate parameter to express the performance of WLEDs. CQS with the ability to examine three elements of

2705
WLEDs: color rendering index, viewer’s preference, and color coordinates, is currently the most completed
color quality index. Figure 5 shows the influence of CaGa2S4:Mn2+
red phosphor on CQS. The results confirm
that with dual phosphor layers WLEDs, the appearance of CaGa2S4:Mn2+
phosphor enhances CQS
significantly, which leads to the better color quality. Even though CaGa2S4:Mn2+
phosphor can improve
the color quality, the amount of reduced emitted light due to this phosphor cannot be ignored. The mathematical
framework of the transmitted blue light and converted yellow light in the structure of two phosphor layers,
a potential part that can promote the performance of WLEDs, is presented in the next part:
Figure 4. The color rendering index of WLEDs
corresponding to CaGa2S4:Mn2+
concentration
Figure 5. The color quality scale of WLEDs
corresponding to CaGa2S4:Mn2+
concentration
The Gaussian function is applied to model the asymmetrical SPD of monochrome [20, 21]:
𝑃𝜆 = 𝑃𝑜𝑝𝑡
1
𝜎√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘)2
𝜎2 ] (1)
In (1), σ is a parameter depending on the peak wavelength λpeak, and the computation of FWHM Δλ can be
presented as:
𝜎 =
𝜆2
𝑝𝑒𝑎𝑘 𝛥𝐸
2ℎ𝑐√2 𝑙𝑛 2
=
𝜆2
𝑝𝑒𝑎𝑘(
ℎ𝑐
𝜆1
−
ℎ𝑐
𝜆2
)
=
𝜆2
𝑝𝑒𝑎𝑘(
ℎ𝑐𝛥𝜆
𝜆1 𝜆2
)
(2)
The SPD of a WLED utilizing yellow YAG phosphor and blue chip can hypothetically be viewed as
the aggregate of the spectra of yellow and blue rays. Practically speaking, nonetheless, the supposed yellow
phosphor radiates light in both yellow and green spectra (as demonstrated from the deliberate spectra in
Figures 1 and 2). In the event that both yellow and blue ranges are picked, the contrast between the essentially
estimated SPD and twofold shading (yellow and blue shading) range model can be spoken to by a green range.
In this manner, so as to speak to the down to earth circumstance, a green range can be added to the twofold
range model, bringing about the accompanying investigative tri-spectrum (B–G–Y) module represented by (3)
and finally altered by (4).
𝑃𝜆 = 𝑃𝑜𝑝𝑡 𝑏
1
𝜎 𝑏√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘 𝑏
)2
𝜎 𝑏
2 ] +𝑃𝑜𝑝𝑡 𝑔
1
𝜎 𝑔√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘 𝑔)2
𝜎 𝑔
2 ]
+𝑃𝑜𝑝𝑡_𝑦
1
𝜎 𝑦√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘_𝑦)2
𝜎 𝑦
2 ] (3)
𝑃𝜆 = 𝜂 𝑏 𝑃𝑜𝑝𝑡_𝑡𝑜𝑡𝑎𝑙
1
𝜎 𝑏√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘_𝑏)2
𝜎 𝑏
2 ] + 𝜂 𝑔 𝑃𝑜𝑝𝑡_𝑡𝑜𝑡𝑎𝑙
1
𝜎 𝑔√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘_𝑔)2
𝜎 𝑔
2 ]
+𝜂 𝑦 𝑃𝑜𝑝𝑡_𝑡𝑜𝑡𝑎𝑙
1
𝜎 𝑦√2𝜋
𝑒𝑥𝑝 [−0.5 ∗
(𝜆−𝜆 𝑝𝑒𝑎𝑘_𝑦)2
𝜎 𝑦
2 ] (4)
Pλ represents the spectral power distribution (SPD) (mW/nm). h, c and λ are the constant of Planck
(J.s), the speed of light (m · s−1
), and the wavelength (nm), respectively. The optical power (W) is indicated by
Popt, and the peak wavelength is expressed as λpeak (nm). Δλ shows the full-width at half-maximum (FWHM)
(nm), while η is the symbol of ratio of specific spectra to white spectrum, dimensionless. The parameters Popt_b,
Popt_g, Popt_y, and Popt_total presents the optical power (W) for the blue, green, yellow, and white spectra, in turn.

 ISSN: 1693-6930
TELKOMNIKA Telecommun Comput El Control, Vol. 18, No. 5, October 2020: 2702 - 2707
2706
Meanwhile, λpeak_b, λpeak_g, and λpeak_y are viewed as the peak wavelengths (nm) for the blue, green, and yellow
spectra, respectively. σb, σg, and σy are respectively known as FWHM-related coefficients (nm) for the blue,
green, and yellow spectra. ηb, ηg, and ηy indicate the ratios of blue–green–yellow (B–G–Y) spectra to white
spectrum, respectively, dimensionless; and λ1, λ2 are the wavelengths at half of the peak intensity.
Hence, it is possible to express the modeled SPD of the phosphor-coated WLED as a tricolor spectrum,
and we can consider it as an extended Gaussian model. In addition, through the application of Mie-scattering
theory, the analysis of CaGa2S4:Mn2+
scattering, and also the computation of scattering cross section Csca for
spherical particles were carried out [22, 23]. Besides that, the Lambert-Beer law is used for calculating
the transmitted light power [24, 25]:
I = I0 exp(-µextL) (5)
I0 represents the incident light power, while L indicates the thickness of the phosphor film (mm). µext in this
formula is the extinction coefficient that can be calculated through this equation: µext = Nr. Cext, with Nr is
the number density distribution of particles (mm-3
), and Cext (mm2
) presents the extinction cross-section of
phosphor particles.
By applying (5), the outcome shows that using dual-layer remote phosphor structure can create a much
better luminous flux than using single-layer phosphor structure. Therefore, this confirms the usefulness of
dual-layer phosphor structure to the improvement of luminous flux in WLEDs. The optical performance of
dual-layer phosphor structure WLEDs with red phosphor CaGa2S4:Mn2+
is greatly influenced by the concentration
of CaGa2S4:Mn2+
. In particular, the extinction coefficient µext demonstrated in the Lambert-Beer law and
concentration of CaGa2S4:Mn2+
increase together. However, the light emission energy increases in inverse
direction to the extinction coefficient µext. As a result, the luminous flux of WLEDs is reduced when increasing
both phosphor layers thickness by adding more CaGa2S4:Mn2+
. Figure 6 illustrates this statement by presenting
decreasing luminous fluxes in all CCTs when the concentration of CaGa2S4:Mn2
moves to 26%. In hindsight,
using dual-layer phosphor structure with red phosphor CaGa2S4:Mn2
already created a much better luminous flux
than the single-layer phosphor one, not to mention the benefits that CaGa2S4:Mn2
has on the development of CRI
and CQS. Therefore, a minor decrease in luminous flux is acceptable, considering how the advantages outweigh
the disadvantage. The most suitable concentration setting depends on the manufacturer choices, as the optimal
concentration of CaGa2S4:Mn2
is the one that can adapt to their demands of quality in WLEDs mass production.
Figure 6. The luminous flux of WLEDs as a function of CaGa2S4:Mn2+
concentration
4. CONCLUSION
This research comes up with an effective technique through experimental results to create WLEDs
with high CRI and luminous efficacy, and allow constant changes to the spectrum of the target. From Lambert
Beer law and linear conversion, a color design model that can change the white light from LEDs to match
the need of the manufacturers was created. The spectrum of the simulation and the measured one are compatible
with each other, the biggest gap between CIE 1931 simulation and the measured is about 0.0063 near the CCT
of 5600 K. This trait is helpful for the formation and application of the color design model.
REFERENCES
[1] S. P. Ying, H. K. Fu, H. H. Hsieh, K. Y. Hsieh, “Color design model of high color rendering index white-light LED
module,” Applied Optics, vol. 56, no. 14, pp. 4045-4051, 2017.

2707
[2] L. Wang, X. Zhang, Z. D. Hao, Y. S. Luo, X. J. Wang, J. H. Zhang, “Enriching red emission of Y3Al5O12: Ce3+
by codoping Pr3+
and Cr3+
for improving color rendering of white LEDs,” Optics Express, vol. 18, no. 24,
pp. 25177-25182, 2010.
[3] V. V. Bakhmet’ev, V. V. Malygin, L. A. Lebedev, M. V. Keskinova, M. M. Sychev, “Synthesis of finely dispersed
NaBaPO4:Eu2+
phosphors and structural investigation of their centers of luminescence,” Journal of Optical
Technology, vol. 84, no. 9, pp. 642-646, 2017.
[4] H. F. Sijbom, R. Verstraete, J. J. Joos, D. Poelman, P. F. Smet, “K2SiF6:Mn4+
as a red phosphor for displays and
warm-white LEDs: a review of properties and perspectives,” Optical Materials Express, vol. 7, no. 9, pp. 3332-3365, 2017.
[5] S. H. Kim, Y. H. Song, S. R. Jeon, et al., “Enhanced luminous efficacy in phosphor-converted white vertical light-
emitting diodes using low index layer,” Optics Express, vol. 21, no. 5, pp. 6353-6359, 2013.
[6] F. Z. Zhang, H. S. Xu, Z. Wang, “Optimizing spectral compositions of multichannel LED light sources by IES color
fidelity index and luminous efficacy of radiation,” Applied Optics, vol. 56, no. 7, pp. 1962-1971, 2017.
[7] D. Dinakaran, C. Gossler, C. Mounir, et al., “Phosphor-based light conversion for miniaturized optical tools,” Applied
Optics, vol. 56, no. 13, pp. 3654-3659, 2017.
[8] Z. Wang, S. Lou, P. Li, Z. Lian, “Single-phase tunable white-light-emitting Sr3 La(PO4)3 : Eu2+
, Mn2+
phosphor for
white LEDs,” Applied Optics, vol. 56, no. 4, pp. 1167-1172, 2017.
[9] Y. Peng, Y. Mou, X. Guo, et al., “Flexible fabrication of a patterned red phosphor layer on a YAG:Ce3+ phosphor-
in-glass for high-power WLEDs,” Optical Materials Express, vol. 8, no. 3, pp. 605-614, 2018.
[10] H. Lee, S. Kim, J. Heo, W. J. Chung, “Phosphor-in-glass with Nd-doped glass for a white LED with a wide color
gamut,” Optics Letters, vol. 43, no. 4, pp. 627-630, 2018.
[11] C. N. Li, H. B. Rao, W. Zhang, C. Y. Zhou, Q. Zhang, K. Zhang, “Self-Adaptive Conformal–Remote Phosphor Coating of
Phosphor-Converted White Light Emitting Diodes,” Journal of Display Technology, vol. 12, no. 9, pp. 946-950, 2016.
[12] N. D. Q. Anh, P. X. Le, H. Y. Lee, “Selection of a Remote Phosphor Configuration to Enhance the Color Quality of
White LEDs,” Current Optics and Photonics, vol. 3, no. 1, pp. 78-85, 2019.
[13] Z. T. Li, H. Y. Wang, B. H. Yu, X. R. Ding, Y. Tang, “High-efficiency LED COB device combined diced V-shaped
pattern and remote phosphor,” Chinese Optics Letters, vol. 15, no. 4, 2017.
[14] C. F. Lai, Y. C. Lee, C. T. Kuo, “Saving Phosphor by 150% and Producing High Color-Rendering Index Candlelight LEDs
Containing Composite Photonic Crystals,” Journal of Lightwave Technology, vol. 32, no. 10, pp. 1930-1935, 2014.
[15] K. A. G. Smet, P. Hanselaer, “Impact of cross-regional differences on color rendition evaluation of white light
sources,” Optics Express, vol. 23, no. 23, pp. 30216-30226, 2015.
[16] J. H. Oh, S. J. Yang, Y. G. Sung, Y. R. Do, “Excellent color rendering indexes of multi-package white LEDs,” Optics
Express, vol. 20, no. 18, pp. 20276-20285, 2012.
[17] Y. Peng, X. Guo, R. X. Li, H. Cheng, M. X. Chen, “Thermally stable WLEDs with excellent luminous properties by
screen-printing a patterned phosphor glass layer on a microstructured glass plate,” Applied Optics, vol. 56, no. 12,
pp. 3270-3276, 2017.
[18] H. L. Shi, C. Zhu, J. Q. Huang, J. Chen, D. C. Chen, W. C. Wang, et al., “Luminescence properties of YAG:Ce, Gd
phosphors synthesized under vacuum condition and their white LED performances,” Optical Materials Express,
vol. 4, no. 4, pp. 649-655, 2014.
[19] C. H. Huang, T. W. Kuo, T. M. Chen, “Thermally stable green Ba3Y(PO4)3:Ce3+
,Tb3+
and red
Ca3Y(AlO)3(BO3)4:Eu3+
phosphors for white-light fluorescent lamps,” Optics Express, vol. 19, no. 101, 2011.
[20] V. Heikkinen, I. Kassamakov, T. Paulin, A. Nolvi, E. Hæggström, “Stroboscopic scanning white light interferometry
at 2.7 MHz with 1.6 µm coherence length using a non-phosphor LED source,” Optics Express, vol. 21, no. 5,
pp. 5247-5254, 2013.
[21] F. Che, L. Wu, B. Hussain, X. Li, C. P. Yue, “A Fully Integrated IEEE 802.15.7 Visible Light Communication
Transmitter with On-Chip 8-W 85% Efficiency Boost LED Driver,” Journal of Lightwave Technology, vol. 34,
no. 10, pp. 2419-2430, 2016.
[22] N. Narendran, Y. Gu, “Life of LED-Based White Light Sources,” Journal of Display Technology, vol. 1,
no. 1, pp. 167-171, 2005.
[23] H. Segawa, N. Hirosaki, “Europium-doped SiAlON and borosilicate glass composites for white light-emitting
diode,” Applied Optics, vol. 54, no. 29, pp. 8727-8730, 2015.
[24] W. G. Bi, X. F. Jiang, H. Q. Wu, F. Zhao, “Improved efficacy of warm-white light-emitting diode luminaires,”
Applied Optics, vol. 54, no. 6, pp. 1320-1325, 2015.
[25] G. Zhang, K. Ding, G. He, P. Zhong, “Spectral optimization of color temperature tunable white LEDs with red LEDs
instead of phosphor for an excellent IES color fidelity index,” OSA Continuum, vol. 2, no. 4, pp. 1056-1064, 2019.

Improving color rendering index of WLEDs with convex-dual-layer remote phosphor geometry using red-emitting CaGa2S4:Mn2+ phosphor

More Related Content

What's hot (20)

Similar to Improving color rendering index of WLEDs with convex-dual-layer remote phosphor geometry using red-emitting CaGa2S4:Mn2+ phosphor (20)

More from TELKOMNIKA JOURNAL (20)

Recently uploaded (20)

Improving color rendering index of WLEDs with convex-dual-layer remote phosphor geometry using red-emitting CaGa2S4:Mn2+ phosphor