Measurements
- 1. MEASUREMENTS! Introduction: Hey everyone! I hope you all are fine. Today we’ll learn the very basics of physics i.e. measurements. In physics, we have to measure length almost everywhere, let’s say for how far a car has moved. Definition: So what is length basically? It is the measurement of distance, or more simply, it is a physical quantity which tells us how far objects are. Its SI unit is metre (m). We can’t really use a single instrument to measure lengths of all magnitudes, can we? Of course not. So the instrument used depends on the magnitude of length to be measured. Every instrument has different precision and range. The question is what is precision and what is range? Precision is simply the smallest unit (minimum length) an instrument can measure, like the ruler you use at school probably measures at least 0.1 cm or 1 mm. Range is the maximum length an instrument can measure, like a metre rule can measure a maximum of one metre, hence it is its range. Easy, isn’t it? While taking readings, however, we might note it incorrectly due to parallax error which can occur due to the wrong positioning of our eye. To avoid this, we must position our eye directly above the reading to be measured. The instruments used are: ● Metre Rule ● Measuring Tape ● Vernier Caliper ● Micrometer Screw Gauge Metre rule and Measuring Tape: We are all familiar with metre rule and measuring tape. A metre rule can measure the lengths within one metre only, while measuring tape can be used for lengths longer than a metre, a length of two and a half metres for instance. Its precision is 0.1 cm. Vernier Calipers: Okay so coming to the vernier calipers, here’s how it looks like:
- 2. Vernier calipers are actually used to measure smaller lengths to acquire a greater accuracy as it’s precision is 0.01 cm i.e. 0.1 mm. The inside jaws shown are used to measure the internal diameters of objects while the outside jaws are to measure the external diameter. The vernier calipers have a main scale and a sliding vernier scale. Now we’re going to learn how exactly are measurements taken using vernier calipers. But before starting this, you should all know about zero error. Hmm..so what is it? It’s actually the error in the instrument which occurs when the zero of the main scale and vernier scale do not coincide when the jaws of the calipers are closed. Task: Google how the zero error is corrected in vernier calipers. 1. Firstly, just read the centimeter mark on the main scale to the left of the 0-mark on the vernier scale. (10 mm in this case) 2. Now, find the millimeter mark on the main scale that is just to the left of the 0-mark on the vernier scale. (6mm as you can see)
- 3. 3. Now we have to take the readings on the sliding vernier scale. For this, look along the ten marks on the vernier scale and the millimeter marks on the main scale, until you find the two that most nearly line up. (0.25mm on the vernier scale) 4. Okay so finally, just simple add this found digit to your previous readings to obtain the diameter of the object, as shown: Micrometer Screw Gauge: Here’s how micrometer looks like:
- 4. And a simpler, more closer diagram: To measure even smaller lengths, micrometer is used as it has an even smaller precision i.e. 0.001 cm or 0.01 mm. It’s range is less than 2 cm. But before taking measurements, again, we’re going to look for zero error. Zero error is absent if the zero of thimble scale coincides with the line on sleeve (datum line) when the anvil and spindle are closed. Task: Google how zero error can be corrected in micrometer. The object whose diameter is to be measured is placed between anvil and spindle (shown above). The ratchet which is a kind of knob is turned to tighten spindle until a ‘tick’ is heard. So now the thing is, what do we do after this? It’s simple. Take a look at the diagram below.
- 5. What is the maximum reading visible on sleeve? It’s 7.5 mm. And on the thimble scale? We’ll determine this by looking at the mark which coincides with the line on sleeve (called datum line), labeled as 0.38 mm with an arrow above. Finally, we’ll add up the two readings, as shown in the diagram above. Questions: Q1. What is the reading on the vernier calipers below? Q2. What is the reading on the micrometer below?
- 6. What is the maximum reading visible on sleeve? It’s 7.5 mm. And on the thimble scale? We’ll determine this by looking at the mark which coincides with the line on sleeve (called datum line), labeled as 0.38 mm with an arrow above. Finally, we’ll add up the two readings, as shown in the diagram above. Questions: Q1. What is the reading on the vernier calipers below? Q2. What is the reading on the micrometer below?