Real time co-simulation platform using opal-rt and opnet for analyzing smart grid performance

Real-time Co-simulation Platform using OPAL-RT
and OPNET for Analyzing Smart Grid Performance
D. Bian, Student, IEEE, M. Kuzlu, Senior Member, IEEE,
M. Pipattanasomporn, Senior Member, IEEE, and S. Rahman, Fellow, IEEE
Advanced Research Institute
Virginia Tech
Arlington, VA, USA 22203
Y. Wu, Student, IEEE
Industrial Information and Control
System Department
KTH Royal institute of technology
Stockholm, Sweden 10044
Abstract— The objective of this paper is to present a real-time
co-simulation platform for analyzing electric power grid
operation, taking into account integrated communication
systems. This paper discusses how a co-simulation platform can
be set up using OPNET and OPAL-RT as communication and
power system simulators, respectively. A simplified distribution
automation case study is demonstrated to show how the co-
simulation platform can be used to analyze performance of the
smart grid operation in real-time.
Keywords— real-time, co-simulation, Java Eclipse, OPNET, RT-
LAB, OPAL-RT, System-in-the-Loop, smart grid applications.
I. INTRODUCTION
A smart grid is regarded as a complex network where
electric power systems and communication systems are
interdependent [1]. Relying on communication technologies,
many smart grid applications can be implemented in electric
power grids, such as demand response, distribution
automation, etc. Since communication systems have intrinsic
characteristics, such as latency, data error and package lost,
this will affect the reliability and security of smart grid
operation. In [2, 3, 4], benefits and potential impacts that
communication networks have introduced to a smart grid are
discussed. Because smart grid operation relies on
communication technologies, analyzing its performance
needs to consider operation of both power and
communication systems.
PowerWorld, MATLAB/Simulink, GridLAB-D, RT-LAB
are popular power system simulation tools. OPNET, NS2/
NS3 and OMNeT++ are popular communication and network
simulators. Nonetheless, neither simulation tools for power
system analysis consider the impact from communication
systems, nor can communication system simulators provide
power system analysis. By combining both power system and
communication network simulators, a co-simulation platform
can be developed that enables simulations of electric power
systems that take into account communication network
properties, such as Quality of Service (QoS), latency, etc.
This will allow realistic studies of smart grid operation
integrated with communication systems.
There are several co-simulation platforms presented in the
literature, including VPNET, OpenDSS-NS2, ADEVS-NS2
and NMLab. The VPNET platform – the combination of
VTB (Virtual Test Bed) and OPNET – is used to analyze the
influence of data blocking on the output voltage of a boost
converter in [5]. A co-simulation platform based on
OpenDSS and NS2 network simulator is presented in [6], and
this platform has been used to examine the effect of
communication failures on smart grid operation. NS2
cooperated with ADEVS (A Discrete Event System
simulator) is also used to simulate the communication delay
on power system monitoring and control in [7]. In [8], a co-
simulation framework called NMLab, which is a combination
of MATLAB and NS2, is introduced. This paper introduces a
real-time co-simulation platform using OPNET and OPAL-
RT. This platform is unique in that it allows simultaneous
simulations of power system and communication networks in
real-time.
Section II summarizes popular simulators for both
communication and power system analyses. In Section III, the
classification of co-simulation platforms is discussed, and then
the process to set up a real-time co-simulation platform based
on OPNET and OPAL-RT is described. In Section IV, a
distribution automation test case based on a remote control of
a switch is simulated on this real-time co-simulation platform.
Simulation results are then discussed.
II. SIMULATION TOOLS FOR POWER AND
COMMUNICATION SYSTEMS
In this section, widely used power and communication
system simulators are summarized, including PowerWorld,
OpenDSS, SimuLink, RTDS and OPAL-RT for power
system analysis, and NS2/NS3, MONeT++ and OPNET for
communication system simulation.
978-1-4673-8040-9/15/$31.00 ©2015 IEEE
Authorized licensed use limited to: ULAKBIM UASL - Mersin University. Downloaded on July 23,2021 at 16:34:55 UTC from IEEE Xplore. Restrictions apply.

2
A. Simulation tools for Power System Analysis
PowerWorld from PowerWorld Corp. is an interactive
power system simulation package designed to simulate high
voltage power system operation. This software contains
power flow analysis package capable of efficiently solving
power system models [9].
OpenDSS, an open-source simulator from EPRI, is a
comprehensive electrical power system simulation tool for
analyzing power distribution systems. OpenDSS supports
nearly all frequency domain analyses commonly performed
on electric utility power distribution systems. Additionally, it
supports many new types of application analyses, which are
designed to meet future needs related to smart grid,
renewable energy research, etc. [10].
Simulink, developed by MathWorks, is data-flow
graphical programming software for modeling, simulating
and analyzing dynamic systems. It supports simulation,
automatic code generation, continuous test and verification of
embedded systems. Integrated with MATLAB, it can
incorporate MATLAB algorithms into models and export
simulation results to MATLAB for further analysis [11].
Several kinds of real-time hardware-based simulation
platforms are available, i.e., Real-Time Digital Simulator
(RTDS) and OPAL-RT. These platforms enable model
execution at the same rate as actual time.
RTDS is a real-time power system simulator. High-speed
simulation, closed-loop testing of protection and control
equipment and hardware-in-the-loop applications are
supported by RTDS [12].
OPAL-RT can be used to design, test and optimize control
and protection systems for power grids, power electronics,
etc. In addition, the RT-LAB, core OPAL-RT software,
enables users to develop models suitable for real-time
simulation. RT-LAB models are fully integrated with
MATLAB/Simulink [13].
B. Communication System Simulators
Network Simulator versions 2 and 3 (NS2/NS3) are open-
source discrete event network simulators, targeting
communication and network research. They support
simulations of IP-based applications (including TCP, UPD,
etc.), routing and multicast protocols over all kinds of
networks (both wired and wireless). NS2 core is written in
C++ programming language. Therefore, C++ is needed to
create new network models or protocols. NS3, the successor
of NS2, includes some new features, such as support for the
Python programming language, improved scalability, and etc.
[14].
OMNeT++, as a discrete event simulation environment, is
an open-source software. Since OMNeT++ is component-
based and provides a generic and flexible architecture, it is
widely used to simulate complex information technology
systems, queuing networks, and etc. Communication network
simulation is one of the most popular applications of
OMNeT++ [15].
OPNET Modeler is a commercial discrete event network
simulator which focuses on network performance simulation.
OPNET provides toolsets, such as: node models that specify
interface of a network component; process models that
abstract the behavior of a network component; a project
window that defines network topology and link connections;
and a simulation window that captures and displays
simulation results. OPNET Modeler has a high-level user
interface offering access to a large library of blocks, which
represents different models and functions. In addition,
OPNET Modeler provides System-in-the-Loop (SITL) that
allows physical hardware devices and a simulator to interact
as a unified system. SITL can also allow multiple physical
networks to communicate through a simulation [14].
C. Choosing Simulators for Real-Time Co-Simulation
In this paper, OPNET and OPAL-RT are chosen to
develop a real-time co-simulation platform. OPNET is chosen
because it is well designed and widely used commercial
software that provides more standard packages than other
communication simulators discussed above. It also offers a
user-friendly interface. For power system real-time
simulation, OPAL-RT is chosen because RT-LAB, coming
with OPAL-RT, has a number of ready-to-use models and it
can be integrated with MATLAB/Simulink. Having access to
a number of standard packages and ready-to-use models will
facilitate simulations of a number of smart grid applications.
III. CO-SIMULATION PLATFORM
In this section, the classification of co-simulation platform
is discussed. Components of the real-time co-simulation
platform are presented, together with discussion on the co-
simulation platform set up.
A. Co-Simulation Platform Classification
The co-simulation platform can be classified into non real-
time (off-line) and real-time, as discussed below.
1) Offline Co-Simulation (Non Real-time)
In a non real-time co-simulation, two simulators are
generally runs separately. In order to realize accurate
information exchange between power and communication
systems, it is necessary to synchronize the simulation time
step, while the operation of two simulators does not need to
be synchronized. For a non real-time platform, a
communication simulation runs and simulation results are
saved into a file, which is shared with the power system
simulator. This file is used when the power system simulator
needs information about communication simulation results.
Easy setting up is the advantage of this non real-time co-
simulation platform. However, the accuracy of simulation
results can be limited due to asynchronous operation of two
simulators.
2) Real-Time Co-Simulation
A real-time co-simulation platform needs an interface that
can enable the information exchange between two simulators.
The synchronization of two simulators relies on this interface,

3
which serves as a data buffer that allows real-time packet
exchanges using protocols, like TCP or UDP. In a real-time
co-simulation platform, two simulators run synchronously.
As an advantage, a real-time co-simulation platform can
handle large and complex systems without manual
intervention. However, the initial set up is time-consuming
and multiple PCs along with the real-time simulator are
necessary to set up a real-time co-simulation platform.
B. Components of a Real-Time Co-Simulation Platform
The following components, as shown in Figure 1, are
necessary to establish a real-time co-simulation platform for
simulating smart grid operation. This paper discusses this
real-time co-simulation platform in the context of a
distribution automation application.
Figure 1. Connection among OPAL-RT, OPNET and Java Eclipse.
1) Control Center Model
A distribution automation control center is simulated using
a PC that has Java Eclipse installed. This control center is
responsible for monitoring voltage levels and controlling
selected devices in a distribution system. Based on the
voltage information monitored, the control center makes a
decision and sends control commands to selected devices.
2) Electric Power System Simulator
To set up an electric power system, OPAL-RT and a PC
that has RT-LAB installed are used. The power system model
is built using readily available blocks from RT-LAB library.
Once the simulated model is compiled successfully in RT-
LAB, the power system model can be loaded into the real-
time simulator, i.e., OPAL-RT.
3) Communication System Simulator
A PC with OPNET installed is used to simulate the
communication system. The communication system model is
configured to enable information exchanging between the
control center and the power system model. Simulation
results can provide communication latency, data dropping,
etc.
4) Connections among the Control Center Model, and the
Electric Power and Communication System Simulators
The connection between the power system simulator (i.e.,
OPAL-RT) and the communication system simulator (i.e., the
PC that has OPNET installed) is set up using an Ethernet
interface. Similarly, the connection between the OPNET PC
and the control center (i.e., the PC that has Java Eclipse
installed) is also set up using an Ethernet interface.
SITL, a model provide by OPNET is used to enable
exchange of packets between OPNET and OPAL-RT/Java
Eclipse. As shown in Figure 1, the PC with OPNET installed
requires two sets of a SITL model and a network card. Each
set, i.e., one SITL model and one network card, functions as
the data exchange interface. With this interface, the data
exchanging between Java Eclipse and OPNET can be
realized. Similarly, OPAL-RT and OPNET are connected
through another set of data exchange interface.
C. Network Configuration and Operation of the Real-time
Co-simulation Platform
The detailed IP and Subnet Mast set up of the real-time co-
simulation platform are illustrated in Figure 2. The operation
sequence of this platform can be divided into two steps.
In the first step, building and compiling the power system
model in the PC with RT-LAB installed; and loading the
Figure 2. Real-time Co-simulation Platform with detailed IP and Subnet Mask

4
compiled power system model into OPAL-RT. In this
experiment, the connection between OPAL-RT and RT-LAB
is established using Wi-Fi interface. See Fig. 2.
The second step is to run control center, OPNET and
OPAL-RT at the same time to co-simulate smart grid
operation. Simulations performed in this step run in real-time.
The package exchanging among these three components uses
the UDP protocol.
IV. CASE STUDY
In this section, a case study of a simplified distribution
automation application is simulated using the real-time co-
simulation platform discussed in Section III.
In the simulation, a simplified distribution system model is
set up in RT-LAB, whose single-line diagram is shown in
Figure 3. As shown, a capacitor bank is connected at Bus 4
through a switch, which is remotely controlled by the control
center located 100 km away. The control center monitors
voltage at Bus 4 and sends control commands to switch
ON/OFF the capacitor based on the voltage level.
Figure 3. Single-line diagram of the simulated power system model
Two scenarios are simulated in this study. In the first
scenario, the control center monitors the voltage at Bus 4, but
there is no control command sent to the switch. In this case,
the switch keeps its open status, implying that the capacitor
bank is always disconnected. In the second scenario, the
voltage at Bus 4 is monitored, and a control command is sent
to switch ON the capacitor bank if the monitored voltage is
lower than 0.95 per unit (pu). When the monitored voltage is
higher than 0.98 pu, a control command is sent to switch OFF
the capacitor bank.
In order to simulate the system in the developed real-time
co-simulation platform, a communication model associated
with this power system model is developed in OPNET, as
shown in Figure 4.
Figure 4. Communication system model in OPNET
It is assumed that the transmission medium between the
control center and the switch for capacitor bank control is a
fiber-optic cable. This is typical for any distribution
automation application. This connection is modeled as a 100-
km fiber-optic cable that connects the control center and the
power system model developed in OPAL-RT, as shown in
Figure 4. In this simulation, two background traffic
generators (one is attached to the control center; the other is
attached to the OPAL-RT node) are used to create
background traffic representing communication traffic of
other smart grid applications that shares the same channel.
Load data used in the case study is derived from a real-
world distribution substation of an electric utility in Virginia.
The data resolution is in one-minute intervals. The load
profile at Bus 4 used in this study is shown in Figure 5 for a
24-hour period.
0 4 8 12 16 20 24
0
0.5
1
1.5
2
2.5
3
3.5
4
x 10
6
Time (hour)
Load
(W)
Figure 5. Load profile at Bus 4
The real-time co-simulation platform is used to simulate
the two scenarios discussed above. Simulation results
showing voltage profiles at Bus 4 are shown in Figure 6.
0 4 8 12 16 20 24
0.93
0.94
0.95
0.96
0.97
0.98
0.99
1
Time (hour)
Voltage
(pu)
Without Capacitor Bank
With Capacitor Bank
Figure 6. Voltage profiles at Bus 4 w/ and w/o the capacitor bank
For the first scenario, the capacitor bank is always
disconnected. Voltage at Bus 4 without the capacitor bank is
shown as the dotted blue line in Figure 6. The voltage is

5
lower than 0.95 pu during the morning peak period, which
begins at 7 am.
In the second scenario, voltage at Bus 4 is shown as the
solid red line in Figure 6. The voltage drops below 0.95 pu at
around 7:30 am. Therefore, the switch is closed to connect
the capacitor bank when the command from the control center
is received. The recorded latency is around 0.002 seconds.
This represents the duration from when the voltage is
measured at Bus 4 to when the switch receives the command
from control center. Once the switch is closed, voltage at Bus
4 is increased above 0.95 pu as expected. Note that this
0.002-second latency is obtained assuming that the occupied
bandwidth of the fiber-optic communication channel is less
than 50% using the background traffic generators.
Figure 7 illustrates communication latencies for the switch
to receive commands from the control center. Using the
background traffic generators, three cases with different
background traffic are simulated, i.e., 0%, 50% and 100% of
the channel bandwidth.
Figure 7. Communication latency
When the background traffic is lower than the channel
bandwidth, the latency relies on the channel length. It can be
seen that with 0% and 50% bandwidth utilization, the
latencies are around 0.002 seconds, as shown as the solid line
and the line with dots in Figure 7.
With smart grid development, communication channels
may need to be shared with many other smart grid
applications. In some situations, the channel utilization can be
close to 100% of its capacity during certain peak periods. The
latency may also increase due to the queueing delay caused
by high data transfer. An example of latency with 100%
channel utilization is shown as the dashed line in Figure 7.
Under this situation, poor communication performance may
potentially have negative impacts on the operation of the
smart grid, depending on criticality of smart grid applications.
Therefore, the real-time co-simulation platform is helpful for
analyzing the impact of communication failure on smart grid
operation.
V. CONCLUSION
This paper discusses a real-time co-simulation platform set
up using OPNET and OPAL-RT. In this platform, the
simulation of power system operation takes into account the
communication system performance. The detailed network
configuration and operation of this platform are discussed. A
simplified distribution automation case study is simulated on
this real-time co-simulation platform. Results of the case
study verify that this platform can provide a real-time co-
simulation analysis for smart grid applications, such as the
impact of communication system failures.
REFERENCES
[1] Fang, Xi; Misra, Satyajayant; Xue, Guoliang; Yang, Dejun, "Smart
Grid -The New and Improved Power Grid: A
Survey," Communications Surveys & Tutorials, IEEE , vol.14, no.4,
pp.944-980, 2012.
[2] U.S. Department of Energy, “A survey of wireless communications
afor the electric power system” [Online], Available:
https://www.pnnl.gov/nationalsecurity/technical/secure_cyber_systems/
pdf/power_grid_wireless.pdf. Retrieve: Nov. 2014.
[3] ABB North America, “Power systems automation and communication
protection and control for reliable and optimized power delivery”
[Online], Available:
http://www05.abb.com/global/scot/scot400.nsf/veritydisplay/ae01e7a2e
47c7a9fc1257bf3004681e9/$file/9AKK105713A8759_LoRes_en_Pow
er_Systems_Automation_and_Communication_ABB_North_America.
pdf. Retrieve: Nov. 2014.
[4] Karlheinz Schwarz, “Monitoring and control of power systems and
ocmmunication infrastructures based on IEC 61850 and IEC 61400-25”
[Online], Available:
http://www.nettedautomation.com/download/pub/dt-tampa-
paper_2010-03-24.pdf. Retrieve: Nov. 2014.
[5] Li, W.; Monti, A.; Luo, M.; Dougal, R.A., "VPNET: A co-simulation
framework for analyzing communication channel effects on power
systems," IEEE Electric Ship Technologies Symposium (ESTS), pp.143-
149, April 2011.
[6] Godfrey, T.; Mullen, S.; Dugan, R.C.; Rodine, C.; Griffith, D.W.;
Golmie, N., "Modeling Smart Grid Applications with Co-
Simulation," IEEE Smart Grid Communications (SmartGridComm)
Conference, pp.291,296, Oct. 2010.
[7] Nutaro, J.; Kuruganti, P.T.; Miller, L.; Mullen, S.; Shankar, M.,
"Integrated Hybrid-Simulation of Electric Power and Communications
Systems," IEEE Power Engineering Society General Meeting, pp.1-8,
June 2007
[8] Heimlich, O.; Sailer, R.; Budzisz, L., "NMLab: A Co-simulation
Framework for Matlab and NS-2," Advances in System Simulation
(SIMUL) Conference, pp.152-157, Aug. 2010
[9] PowerWorld Corporation, [Online], Available:
http://www.powerworld.com/products/simulator/overview. Retrieve:
Nov, 2014.
[10] Electric Power Research Institute, [Online], availabe:
http://smartgrid.epri.com/SimulationTool.aspx. Retrieve: Nov, 2014.
[11] RTDS Technologies, [Online], Available:
http://www.rtds.com/hardware/hardware.html. Retrieve: Nov, 2014.
[12] OPAL-RT Technologies, [Online], availabe: http://www.opal-
rt.com/product/rt-lab-professional-real-time-digital-simulation-
software. Retrieve: Nov, 2014.
[13] Jianli Pan, “A Survey of Network Simulation Tools: Current Status and
Future Developments”, [Online], Available:
http://www.cs.wustl.edu/~jain/cse567-08/ftp/simtools/index.html
[14] “Introduction to SITL” [Online], Available:
https://support.riverbed.com/bin/support/static//doc/opnet/17.5.A/online
/modeler_17.5_PL5/Tutorials/wwhelp/wwhimpl/common/html/wwhelp
.htm#href=sitl_tut_1.html&single=true Retrieve: Nov, 2014.
[15] OMNeT++, [Online], Available: http://www.omnetpp.org/models
Retrieve: Nov, 2014.

Real time co-simulation platform using opal-rt and opnet for analyzing smart grid performance

More Related Content

What's hot (18)

Similar to Real time co-simulation platform using opal-rt and opnet for analyzing smart grid performance (20)

Recently uploaded (20)

Real time co-simulation platform using opal-rt and opnet for analyzing smart grid performance