Wireless meter reading system

1. INTRODUCTION

1.1 GENEREL
Now a day’s wireless communication has become ubiquitous around the world and its
application for gauging consumption of utilities by customers is rapidly gaining pace, not only in
the developed world but also in the developing countries.

To introduce this concept in the Sultanate of Oman, a model of Wireless Automatic Meter
Reading System (WAMRS) has been developed, in which the wireless communication is based
on IEEE 802.15.4 (ZigBee) standard and security is implemented by following the Direct
Sequence Spread Spectrum (DSSS) protocol. Successful demonstration of WAMRS prototype
has made it possible to be implemented in Oman on a larger scale for meter reading applications.

Electricity is the driving force behind the development of any country. With the rapid increase in
residential, commercial, and industrial consumers of electricity throughout the world, it has now
become imperative for utilities companies to devise better, non-intrusive, environmentally-safe
techniques of gauging utilities’ consumption so that correct bills can be generated and invoiced.
Traditionally, the electricity meters are installed on consumer’s premises and the consumption
information is collected by meter-readers on their fortnightly or monthly visits to the premises.

This method of gauging electricity consumption has the following disadvantages:

 Sometimes the meters are installed inside people’s homes and, if the consumer is not at
home, the meter-reader cannot record the fortnightly or monthly consumption and then
the utilities’ company has to resort to considering the average bill-amount of the previous
months as an indicator of the likely consumption for the current month. This results in
burden for both consumer and the electricity supply company. May be the consumer has
not utilized similar amount of electricity in the current month as in the previous months
for reasons such as, holidaying elsewhere or being in the hospital, etc. during the month,
and sending him a bill for a larger amount based on his history of electricity consumption
may result in his/her financial hardship. This method of billing is also not suitable for the
electricity supply company because it gives inaccurate account of the overall electricity
consumption in the consumer’s area and may ultimately result in errors in future planning
by the company.
 Hiring of a number of meter readers by utilities’ companies and providing means of
transportation to them is an expensive burden on the companies’ budgets. Moreover,
these visits of the meter readers to consumers’ premises generate pollution in the air
which has negative impact on the environment and the greenhouse effect.

 Dissatisfaction of some customers who consider meter-readers’ entrance to their homes
as some sort of invasion of their privacy. This is especially applicable in countries, like
Oman, where during the day most men are outside of their homes earning a living and
only women are at home doing the housework.
In order to overcome these disadvantages of the traditional meter reading system, efforts are
underway around the world to automate meter reading and to provide comprehensive
information to the consumer for efficient use of the utilities.

1.2 BASIC CONCEPT FOR OUR PROJECT

The basic concept for our project comes from the WIRELESS AUTOMATIC METER
READING SYSTEM project undertaken by the Sultan Quaboos University, Oman.

The main attributes of that project are as follows:

Overall global view of WAMRS project

An overall global view of WAMRS is shown in Fig. The main goal of `WAMRS project was to
send periodical readings of an electricity meter wirelessly to a server in the billing office of the
electricity supply company. There were central point’s covering each geographical area, since
each premises unit would have limited range of wireless coverage, while the central point’s
would have long-range wireless transmitters that could deliver the meter-reading data over long
distances to the billing office. The server in the billing office had a highly secure database
system which enabled authorized staff members of the electricity supply company to read and
print electricity bills. For premises out of the coverage area of any central point, the solution
proposed was to make the nearest premises unit (covered by a central point) as the central point
for such remote premises. This added a constraint on the wireless device used for such purpose
because such a device should have the capability of both sending and receiving the data.

A block diagram of global WAMRS design is given in Fig. It consists of three main parts, the
Sender (also called Premises Unit), the Central Point’s Unit, and the Receiver (server database at
the billing office of the electricity supply company).

Block diagram view of the global WAMRS design

1.2.1. The Sender (Premises Unit)

1.2.1.1. Digital Meter
After conducting a survey of the digital kWh meters available in the international market and
comparing their prices and characteristics, we decided to use a single-phase MK-60LCD digital
meter, provided by the Circutor Company. This meter satisfied Omani power systems
requirements since it runs with 230V/50Hz supply and can handle maximum current of
60(120)A. The meter has a pulse port and a memory to store records in case of power shutdown.

Note that designed WAMRS for a single-phase system mainly because the cost of three-phase
digital meter was about US$100 more than the cost of a single-phase meter & this would have
taken us out of our budget allocation. Nevertheless, the theory of implementing a three-phase
WAMRS is identical to a single-phase wireless automatic meter-reading system.

1.2.1.2. Bus controller
A bus controller is needed to select the input to the microcontroller from either the digital meter
for reading the consumption or the wireless chip which can receive data from the central point or
the remote location (if it exists). A simple 2x1 multiplexer was considered sufficient to serve as
bus controller for this project.

1.2.1.3. Microcontroller
The main function of the microcontroller is to control the communication between the Premises
Unit and the Central Points, and also between different components of the Premises Unit. It is
also responsible for encrypting the data before transmission and for decrypting the received
message. For this project, Philips P87LPC764 microcontroller was selected because it satisfied
the requirements of the project (low power consumption, two-wire communication port, full
duplex UART for digital meter-wireless chip communication, and low cost of about US$3).

1.2.1.4. NVRAM
A non-volatile RAM was chosen because it is faster compared to most kinds of ROM and is
cheaper for the size of memory needed for the project. The memory was segmented into different
blocks: one block of memory was used to store configuration files which can be updated
remotely by the server through the microcontroller, another block was assigned for storage of the
random numbers table used for authentication, another block was used for recording the daily,
weekly, and monthly power consumptions, and the last block of memory contained a list of IP
addresses with which the current unit can send or receive data. Philips 24LC16B memory chip
was used for the project which has a size of 16KB, works at 3V and needs only two wires to
communicate with the microcontroller. It has the ability to store data for more than 200 years and
its cost is about US$0.50.

1.2.1.5. Real-time Clock
The function of the clock is to “wake” the chip up at pre-determined time for transmission of
power consumption and then to put it back to “sleep” to conserve power. Ricoh RV5c339A was
chosen for the project because of its accuracy and ignorable active mode power consumption. It
has an alarm feature for interrupting the microcontroller.

1.2.1.6. Transmitting Chip
The first step in designing any wireless network is to perform a site survey which involves an
investigation of critical features and characteristics of the site (building) in terms of building
material, floor dimensions, and possible sources of interference. Since the designed system was

planned to be installed at a laboratory building in the Department of Electrical and Computer
Engineering at Sultan Qaboos University (Oman), the following data was obtained during the
site-survey phase:

The dimensions of each of the three floors of the building are 115.2x22.8 meters. The building is
made of concrete and most of the walls are made of cement-based material.

No metal shields are used in the building but there are a number of small metal studs around the
extremities of each floor.Major source of interference might be Bluetooth-enabled devices
(mobile phones, PDAs, and laptops). After comparison of various commonly available wireless
communication techniques, ZigBee was chosen for this project. ZigBee is very secure (uses
Advanced Encryption Standard) and is self-configuring. It allows ad-hoc networks, provides
reliable data transfer in noisy, interference-rich environments, and addresses the unique needs of
most remote monitoring.

Among the various available ZigBee products, Maxstream’s XBee-PRO chip was most suitable
in terms of range, data rate, security, and cost so this chip was chosen for the project. The chip is
available with a whipantenna, a low-profile chip antenna, or U.FL connector (to which external
antenna can be connected). The whip antenna provides a better range compared to a chip antenna
in both outdoor (1335 m) and indoor (43 m) environments so whip antenna was selected for the
project.

1.2.2. At the Central Points

When data has to be transmitted wirelessly over long distances, it is necessary to have some
mechanism at predetermined distances from the sender for temporarily receiving and
retransmission of data to the designated receiver. As shown in the WAMRS block diagram
(Fig.), at the central points, the system will consist of a transceiver, microcontroller, the clock,
and a NVRAM. This hardware is similar to the hardware at the Premises Unit, so at the time of
implementation of the system, each premises unit can be configured to behave both as a sender
(when transmitting its data) and a central point unit (for temporarily receiving/retransmission of
data coming from other neighboring premises units) at different times.

1.2.3. The Receiver (at the Billing Office)
The hardware at the billing office consisted of a receiving chip and a database server.

1.2.3.1. Receiving Chip
To remain compatible with the XBee- PRO transmitting chip, the XBee-PRO PKG (Receiver)
was selected as the receiving chip for the project. It is a small, high performance, low cost
wireless data receiver operating in the 2.4 GHz ISM (Industrial, Scientific, and Medical) band
and has FCC approval for operation without a license. Based on IEEE 802.15.4 standard, it uses

OQPSK (Offset Quadrature Phase Shift Keying) with a half-sine pulse shaping filter as
modulation.

1.2.3.2. Database Server
The database server requires software for communication with the premises unit of each
consumer and, based on the consumption data received, it needs to generate an electricity bill.
Prior to allowing communication between the sender and receiver, it will be necessary to
authenticate the administrator at the billing office and the sender at the Premises Unit.

To validate the source, a very simple approach used was a three-way handshake such as that used
in TCP. In TCP, this handshake is used for synchronization, but in this project, this technique
was used for authentication of the source. A block of memory in NVRAM of each Premises
Unit, at the central point , and the memory of the server at the billing office is used to store a
256rows x 3columns table filled with random numbers in 0-255 range (all 768 entries of the table
will be the same stored at all locations of the system). The source at the Premises Unit will send
an initial request including a random number selected from the first column of its stored table.
The destination (at the central point or the billing office) will reply with a datagram containing
the random number entry in the second column of the same row (as the sender) of its stored
table. At this point, the source has authenticated the destination, so it sends its data with the
random number entry in the third column of the same row of its stored table to authenticate itself
to the destination. The data packet used in WARMS consists of the following fields:

Source Destination (S/D) IP Addresses: A 128-bit field, which has been divided into two 64 bit
unique IP addresses for both source and destination. This is important for authentication of the
source using three-way handshake protocol. Original Source/Original Destination (OS/OD): This
is of the same size as the S/D field and is important in case of the Premises Units which are
located at remote places or if the server wants to connect to a certain Premises Unit through a
certain central point. Power Consumption: This field is 20-bits long (to accommodate maximum
meter reading of 999,999 kWh) and contains the latest digital meter reading sent by the Premises
Unit. Random Sequence Number: An 8-bit field, used for authentication, as explained
previously. Using password to authenticate the administrator in the billing office, he/she can
generate an electricity bill for the consumer, upon receiving the consumption data. For the
project, the bill generator program was written using Visual Basic/Macromedia Flash MX,
interfaced with a SQL database.

You can download complete report from
“www.thoughtcrackers.blogspot.com”

Wireless meter reading system

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Wireless meter reading system (20)

More from mangal das (20)

Recently uploaded (20)

Wireless meter reading system