Zapi sem 2 manual

INSTALLATION AND
USER MANUAL
CHOPPER SEM2
ELECTRONIC INDUSTRIAL DEVICES
42028 - POVIGLIO - (R.E.) - Via Parma, 59 - ITALIA
Tel. (0522) 960050 (r.a.) - Tlx. 530021 AINDRE I - Fax (0522) 960259

INDEX
Page
LEGEND .............................................................................................................. 3
COLOUR CODES (Single Colours) ...................................................................... 3
1 Introduction to the ZAPI-MOS family .......................................................... 4
2 General characteristic................................................................................... 5
2.1 Technical Specification.......................................................................... 5
2.2 Control Units.......................................................................................... 5
2.2.a Microswitches.............................................................................. 5
2.2.b Potentiometer ............................................................................... 6
2.3 Safety & Protection Features. ............................................................... 7
2.4 Direction Orientation ............................................................................. 7
2.5 Operational Features ............................................................................ 8
2.6 SEM2 chopper diagnosis ...................................................................... 9
2.7 Thermal Considerations. ....................................................................... 9
2.8 General Instructions and Precautions ................................................. 10
3 Installation. .................................................................................................. 11
3.1 Connection Cables. ............................................................................. 11
3.2 Contactors. .......................................................................................... 11
3.3 Fuses. ................................................................................................. 11
3.4 Description of SEM 2 Connectors. ...................................................... 12
3.5 Description of Power Connections ...................................................... 14
3.6 Mechanical Drawing & Dimensions ..................................................... 15
4 Programming & Adjustments using Digital Console............................... 16
4.1 Adjustments via Console ..................................................................... 16
4.2 Description of Console & Connection.................................................. 16
4.3 Description of Standard Console Menu............................................... 17
5 SEM2 Traction ............................................................................................. 18
5.1 Description of Programmable Functions (Options). ............................ 19
5.2 Description of Parameters that may be Programmed ......................... 21
5.3 Table of Adjustments........................................................................... 22
5.4 SEM 2 Traction Standard Wiring Diagrams ........................................ 23
5.5 Sequence for SEM 2 Traction Settings. .............................................. 24
6 SEM 2 Diagnostics ...................................................................................... 26
6.1 Analysis of Alarms displayed on the Console ..................................... 27
6.2 Tester. Description of the Functions ................................................... 30
6.3 Description of the Console SAVE Function ......................................... 32
6.4 Description of Console RESTORE Function. ...................................... 33
6.5 Description of Alarms Menu. ............................................................... 34
6.6 Description of Console PROGRAM VACC function. ........................... 35

7 Recommended Spare parts for SEM 2 ...................................................... 36
8 Periodic Maintenance to be repeated at times indicated. ....................... 37
= The information contained in the paragraphs marked with this symbol is essential
for the purpose of safety.
SIGNED IN APPROVAL
COMPANY DEPT. SERVICES MANAGEMENT EXECUTIVE
ENGINEERING SECTION EXECUTIVE
EXPORT MANAGER
Publication No. AC1ZP0CA
Edition: Aprile 1998

LEGEND
BACK.FW = Inching forward direction switch
BACK.REV = Inching reverse direction switch
BTG = Main Contactor Coil
CMM = Common Feed to Microswitches
CPOT = Potentiometer Wiper
FORW = Forward switch
HB = Handbrake switch
KEY = Key switch input
NAUX = Negative supply for auxiliary load
NPOT = Potentiometer Negative supply
PAUX = Positive supply for auxiliary load
PB = Brake pedal switch
PPOT = Potentiometer Positive supply
REV = Reverse switch input
SR1 = Speed Reduction 1 Microswitch
SR2 = Speed Reduction 2 Microswitch
TG = Main Contactor
VMN = Voltage to Negative of Motor
COLOUR CODES (SINGLE COLOURS)
The following Codes represent the colours of individual wires used by Zapi (Unless
specified otherwise).
A - Orange
B - White
BB - Blue
C - Sky Blue
G - Yellow
GG - Grey
M - Brown
N - Black
R - Pink
RR - Red
V - Green
VV - Purple

1 INTRODUCTION TO THE ZAPI-MOS FAMILY
The ZAPIMOS chopper family represents ZAPI’s answer to the needs of the 90’s.
To ensure that products remain on the market, without running the risk of becoming
technically obsolescent, the ZAPIMOS family offers the following features:
- Advanced technology.
- Economical costs.
- Maximum safety.
- Maximum flexibility.
- Open to future technical innovations.
- Optimum level of protection.
The design has been derived from:
- High Frequency Mos Technology .
- Real time control over the internal and external components that influence the
behavior of the machine, with self diagnosis of the checking circuits themselves.
- Stored Program Machine (SPC), where the hardware is completely separate from
the functions to be configured. The programme is parametric and can easily be
modified by the end user.
- Various chopper configurations can be selected by the user, without the need for
hardware modifications.
- Future technological updates are made easy for the user.
The communication protocol will continue to evolve, thereby offering increas-
ing possibilities of interaction and expansion. For this reason, the Zapimos
family offers a standard dialogue mode with external systems. This allows
interfacing with
commercially available machines. Zapi can offer a range of individually designed
Console Software with various features and prices.
- SEM 2 meets the requirements of (IP54). This provides excellent protection against
spray (water, acid.), and against the ingress of dust or small foreign particles.
Access to the control logic is very simple, and allows simple substitution or replace-
ment.
- The SEM2 family of Choppers are suitable for operating on DC voltages from 24 to
48V inclusive, with maximum armature current up to 350A.
The choppers may be used to control DC Separately Excited Motors with power
ratings up to 5.5kW.

2 GENERAL CHARACTERISTIC
2.1 TECHNICAL SPECIFICATION
Chopper for Separately Excited DC motors ...................................................2.5 ÷ 5.5kW
Regenerative Braking.
Voltage Range ......................................................................................24 to 48 Volts DC
Maximum Field Current (all the versions.............................................................50 Amps
Armature Switching Frequency ...............................................................................16kHz
Field Switching Frequency ........................................................................................1kHz
Maximum Ambient temperature .............................................................................+ 40°C
Minimum Ambient temperature ................................................................................-30°C
Maximum temperature of Chopper ........................................................................+ 85°C
Resistance of field Winding ............................................................................. 0.3 to 0.6W
VERSION MAXIMUM CURRENT BOOSTER CURRENT
VOLTAGE DROP AT
TOTAL CONDUCTION
24V / 500A 500A 580A 0.25V at 200A, 25°C
36V / 500A 500A 580A 0.25V at 200A, 25°C
48V / 350A 350A 400A 0.25V at 100A, 25°C
2.2 CONTROL UNITS
2.2.a Microswitches
- Microswitches should have a contact resistance lower than 0.1W , and a leakage
current lower than 100 µA.
- When full load current is being drawn, the voltage drop across the Key Switch con
tacts must be lower than 0.1V.
- If an Electromagnetic Brake is used, the Handle Microswitch must operate the Brake
Coil.
- The Microswitches send a voltage signal to the microprocessor when an operating
request (running) is made.

2.2.b Potentiometer
The Potentiometer should be wired in the 3 - Wire Configuration.
CPOT (A2) signal ranges from 0 to 10V.
Minimum Potentiometer Resistance :500W
Maximum Potentiometer Resistance : 10kW
Faults can occour if the potentiometer is out of this range.
The Procedure for automatic potentiometer signal aquisition is carried out using the
Console. This enables adjustment of the minimum and maximum useful signal level in
either direction. This function is unique when it is necessary to compensate for asym-
metry with the machanical elements associated with the potentiometer, especially
relating to the minimum level.
The two graphs show the output voltage from a non-calibrated potentiometer with
respect to the mechanical “zero” of the control lever. MI and MA indicate the point
where the direction switches close. 0 represents the mechanical zero of the rotation.
The Left Hand graph shows the relationship of the motor voltage without signal
aquisition being made. The Right Hand Graph shows the same relationship after signal
aquisition of the potentiometer.
The aquisition procedure is disabled if the potentiometer wiper output does not reach a
minimum of 3 V. If a centre tapped potentiometer is not available, it is possible to use a
standard 3 wire pot set in the middle of its full stroke.

2.3 SAFETY & PROTECTION FEATURES.
- Connection Errors :
All Inputs are protected against connection errors.
- Thermal Protection :
If the chopper temperature exceeds 80°C, the maximum current reduces in
proportion to the thermal increase. The temperature can never exceed 85°C.
- Low Battery Charge :
When the battery charge is low, the maximum current is reduced proportionally to
the battery discharge.
- Protection against accidental Start up :
A precise sequence of operations are necessary before the machine will start.
Operation cannot commence if these operations are not carried out correctly.
Requests for drive, must be made after closing the key Switch.
- Protection against uncontrolled movements :
The Main Contactor will not close if :
- The Power Unit is not functioning
- The Logic is not functioning perfectly.
- Main Contactor :
Should be fitted to give protection to the chopper against reverse battery polarity,
and safety.
- External Agents :
The chopper is protected against dust and the spray of liquid to a degree of
protection meeting IP54.
2.4 DIRECTION ORIENTATION
Machines fitted with Tillers, Belly Switches, and Pulse Control Systems providing rapid
reversal should conform to the requirements of Directive prEN 1175. This Directive re-
quires that Direction Orientation should match the following drawing:

2.5 OPERATIONAL FEATURES
- Speed Control .
- Optimum sensitivity at low speeds.
- Speed Reductions in both the directions. Levels can be set using Console.
- Regenerative Braking based on deceleration ramps.
- Three different modes of Braking : Release Braking, Inversion Braking, Speed Limit
Braking.
- Speed Control during descent : the motor speed follows the accelerator. The chop-
per automatically brakes if the motor speed overcomes the accelerator set point.
This provides optimum performance on a gradient.
- Starts on a Ramp without roll back, even without an electric brake.
- Programmable Anti Roll Back : When the Key Switch is closed, if the motor is rotat-
ing, the chopper controls the speed and automatically brakes and keeps the motor at
a very low speed during descent on a gradient. This is a very useful safety feature
and is not driver dependent.
- Self Diagnosis with indication of fault shown via flashing Red Led. (In addition to
Console Display).
- Modification of the parameters via Digital Console. See the specific description.
- Internal Hour Meter that is displayed on the Console.
- Memory of the last 5 Alarms, with relative Hour meter count and chopper tempera-
ture all displayed on the Console.
- Test Function within Console for checking main parameters. See the specific De-
scription.
- High motor and battery efficiency due to High Frequency Switching.
- Presence of a second microprocessor for safety that monitors the CPU that controls
the motor.

2.6 SEM2 CHOPPER DIAGNOSIS
The microprocessor continually monitors the chopper and carries out diagnostic proce-
dures on the main functions.
The diagnosis is made in 4 points:
1) Diagnosis on key Switch closing that checks: the Watch Dog Circuits, the current
sensor, VMN point, Contactor Drivers, the switch sequence for operation is correct,
and the output of the accelerator or tiller is correct.
2) Standby Diagnosis at rest that checks: VMN Point, Contactor Drivers, and Current
Sensor.
3) Diagnosis during operation that checks: Watchdog, VMN Point, Current,
Contactor(s), and VMN when in full conduction.
4) Continuos Diagnosis that checks: Chopper temperature, Battery Voltage.
Diagnosis is provided in 2 ways. The Red Led connected to Connector A will flash a
certain number of times for a given Alarm (See Listings), or the Digital Console may be
used. A permanent Alarm will be displayed on the Console immediately and the RED
LED will flash. An intermittent Alarm will be recorded in the Alarm library, but the RED
LED will only flash at the time of the Alarm.
2.7 THERMAL CONSIDERATIONS.
- The heat generated by the power block must be dissipated. For this to be possible,
the compartment must be ventilated and the heat sink materials ample.
- The heat sink material and system should be sized on the performance requirement
of the machine. Abnormal ambient air temperatures should be considered. In situa-
tions where either ventilation is poor, or heat exchange is difficult, forced air ventila-
tion should be used.
- The thermal energy dissipated by the power block module varies and is dependent
on the current drawn and the duty cycle.

2.8 GENERAL INSTRUCTIONS AND PRECAUTIONS
- Never combine SCR low frequency choppers with SEM2 modules. The filter capaci-
tors contained in the SEM2 module will change the SCR chopper operation and
subject it to excessive workload. If it is necessary to use two or more control units
(eg. Lift + traction), the choppers must be of the High Frequency Zapi family.
- Do not connect the chopper to a battery with a different nominal voltage to the value
indicated on the chopper. A higher battery voltage may cause MOS failure, and a
lower voltage may prevent the logic operating.
- During battery recharge, the SEM2 must be completely disconnected from the bat-
tery. As well as altering the charge current read by the battery charger, the module
can be damaged by higher than normal voltages supplied via the charger.
- The SEM2 module should only be supplied by a traction battery. Do not use the
outputs of convertors or power supplies. For special applications please contact the
nearest Zapi service centre.
- Start the machine the first time with the drive wheel(s) raised from the floor to ensure
that any installation errors do not compromise safety.
- After operation, even with the Key Switch open, the internal capacitors may remain
charged for some time. For safe operation, we recommend that the battery is discon-
nected, and a short circuit is made between Battery Positive and Battery negative
power terminals of the chopper using a Resistor between 10W and 100W .
Minimum 5 W.
- The susceptibility and electromagnetic emmission levels are seriously influenced by
installation conditions. Take particular care with the length of cables and wires,
types of electrical connections, and braided/screened wires.
Zapi declines any responsibility for incorrect or bad operation that can be attributed
to the above circumstances. Above all, the manufacturer of the machine must ensure
that the requirements of EN 50081-2 are met.

3 INSTALLATION.
Install the chopper baseplate onto a flat metallic surface that is clean and unpainted.
Apply a thin layer of thermo-conductive grease between the two surfaces to permit
better heat dissipation.
Despite the protection provided against external agents, the continuous attack of corro-
sive elements and substances may cause oxidization of connector contacts, resulting in
bad operation. Remember this point when deciding the installation position on the
vehicle.
Fix the chopper using the special holes located on the baseplate.
Verify that the wiring of the cable terminals and connectors has been carried out cor-
rectly. Ensure that suppression devices are fitted to the Horn, Solenoid Valves, the
coils of any relays, and contactors not supplied by logic or the chopper itself.
3.1 CONNECTION CABLES.
For the auxiliary circuits use cables better or equal to 0.5mm² section.
For power connections to the motor armature and battery use cable of 25 to 35mm²
section.
For the Field connections use cable of 4mm² section.
For the optimum chopper performance, the cables to the battery should be run side by
side and be as short as possible.
3.2 CONTACTORS.
A Main Contactor, designed for Continuous Operation should be installed. This contac-
tor should be fitted with a coil corresponding to the battery voltage. The current ab-
sorbed by the coil must not be greater than 3A.
Suppression for this contactor coil is within the chopper. Do not use external suppres-
sion. If contactors for power steer motors are supplied from the control logic, the sup-
pression will be inside the chopper logic.
For any Contactor using external suppression, ensure that connections are made re-
specting correct polarity.
3.3 FUSES.
- Use a 6.3A Fuse for protection of the auxiliary circuits.
- For protection of the power unit, refer to diagrams.. The Fuse value shown is the
maximum allowable. For special applications or requirements these values can be
reduced.
- For Safety reasons, we recommend the use of protected fuses in order to prevent
the spread of fused particles should the fuse blow.

3.4 DESCRIPTION OF SEM 2 CONNECTORS.
PIN REFERENCE DESCRIPTION
A1 PLED Positive of Diagnostic Red Led.
A2 NLED Negative of Diagnostic Red Led.
Output Current is 12mA, for this standard type Led.
B1 KEY B+ Supply into logic Downstream of 10A Fuse & Key Switch.
B2 CMM Positive Supply to Hand Brake and Brush / SR2 Microswitches.
B3 PTG Positive Supply to Main Contactor.
B4 BRUSH / SR2 Input from motor brush switch (normally open), or Input from
second speed reduction switch (normally closed).
B5 HB Input from Hand Brake Switch (normally closed).
B6 FAN / HYDRO Negative Output to Fan or Power Steer Contactor Coil.
B7 NTG Negative Supply to Main Contactor.
B8 - BATT Battery Negative.
C1 PPOT Positive Output to Potentiometer (I max = 25mA).
C2 NPOT Negative Output to Potentiometer.
C3 CPOT Input from Potentiometer Wiper, or output of inductive device.

PIN REFERENCE DESCRIPTION
E1 CMM Positive Common Feed to Rev, Fwd, SR1, PB, and Seat
Microswitches.
E2 REV Input from Reverse Direction Microswitch. Active High.
E3 FW Input from Forward Direction Microswitch. Active High.
E4 SR1 Input from First Speed Reduction Switch. Active Low.
E5 PB Input from Pedal Brake Switch. Active High.
E6 SEAT Input from Seat Switch. Active High with delay.
E7 MOT. THERM Input from Motor Thermal Switch.
E8 FREE1 Input from any Active High Switch.
E9 - BATT Battery Negative.
F1 - BATT Battery Negative.
F2 - BATT Battery Negative..
G1 PCLRXD Positive Serial Reception.
G2 NCLRXD Negative Serial Reception.
G3 PCLTXD Positive Serial Transmission.
G4 NCLTXD Negative Serial Transmission.
G5 - Batt Negative supply to Digital Console.
G6 + VL Positive supply to Digital Console.
G7 // Free.
G8 // Free.
L1 CMM Common Supply to Fwd & Rev Backing Switches, Motor thermal
switch, Speed Reduction 3 Switch, and 2 spare switches.
L2 BACK FW Input from Forward Backing Switch. Active High.
L3 BACK REV Input from Reverse Backing Switch. Active High.
L4 ENABLE/ SR3 Input from pedal accelerator (Enable) Active High.or Speed Re-
duction 3 Switch Active Low.
L5 FREE Input from Free Microswitch 1. Active High.
L6 FREE2 Input from Free Microswitch 2. Active High.
L7 NAUX Negative Output to Auxilliary.
L8 PAUX Positive Output to Auxiliary.
L9 FREE3 Free Entry 3. Connected to CMM (if J1= 2-3) or to- Batt
(if J1= 1-2) through microswitch.

NOTES:
1) The BRUSH / SR2 and HB inputs could be connected to Battery Negative (B8). It is
necessary to change the internal link “B” from 1-2 to 2-3. In this case the Normally
Closed microswitches need to be Normally Open, and the Normally Open
microswitches need to be Normally Closed.
2) The REV, FW, SR1, PB, SEAT inputs could be connected to Battery Negative (E9).
It is necessary to change the internal link “A” from 1-2 to 2-3. In this case the Nor-
mally Closed microswitches need to be Normally Open, and the Normally Open
Microswitches need to be normally Closed.
3) The MOTOR THERM, BACK FW, BACK REV, ENABLE/ SR3, FREE inputs could
be connected to Battery Negative (F1 or F2). It is necessary to change the internal
link “C” from 1-2 to 2-3. In this case the Normally Closed microswitches need to be
Normally Open, and the Normally Open Microswitches need to be Normally Closed.
3.5 DESCRIPTION OF POWER CONNECTIONS
+BATT = Positive Supply from Battery.
-BATT = Negative Supply from Battery.
VMN = Negative Supply (via chopper) to Motor.
F1, F2 = Connections to Drive Motor Field Winding.

3.6 MECHANICAL DRAWING & DIMENSIONS

4 PROGRAMMING & ADJUSTMENTS USING DIGITAL CONSOLE
4.1 ADJUSTMENTS VIA CONSOLE
Adjustment of Parameters and changes to the chopper’s configuration are made using
the Digital Console. The Console is connected to the “G” connector of the SEM 2
Chopper.
Pay attention to the polarity of the Console Connector when connecting to
the chopper. The bevel on the connector should be uppermost.
4.2 DESCRIPTION OF CONSOLE & CONNECTION
Digital Consoles used to communicate with SEM2 choppers must be fitted with Eprom
CK ULTRA.

4.3 DESCRIPTION OF STANDARD CONSOLE MENU

5 SEM2 TRACTION
- Input for 3 Wire Potentiometer.
- 3 Speed Reductions.
- Input for Tiller Switch or Seat Switch (delayed).
- Input for Brake Pedal Microswitch.
- Input for Motor Thermal Switch.
- Management of Backing Speed (Programmable).

5.1 DESCRIPTION OF PROGRAMMABLE FUNCTIONS (OPTIONS).
Using the CONFIG MENU of the console, it is possible to select from the following
options:
SUBMENU “SET OPTIONS”:
1 HOUR COUNTER:
- RUNNING: The counter registers travel time only.
- KEY ON: The counter registers when the key switch is Closed.
2 BRUSH SWITCH:
- PRESENT: The Brush Switch provides an input signal from the
motor brushes.
- OPTION #2: The Brush Switch Input may be used as a Second Speed
Reduction.
3 ENABLE SWITCH:
- PRESENT: The Enable Switch provides an input from the pedal
accelerator.
- OPTION #3: The Enable Switch input may be used as a Third Speed
Reduction.
4 AUX FUNCTION:
- OPTION #1: The output on Pin B6 provides a Negative supply to a
fan.
- HYDRO CONT.: The output on Pin B6 provides a Negative supply to the
coil of a steering Contactor.
5 SET BATTERY TYPE: This option allows selection of the Nominal Battery Volt-
age.

Flow Chart showing how to make changes to Configuration Menu using Digital Con-
sole. (Standard Eprom CK ULTRA fitted).
1) Opening Zapi Menu.
2) Press Top Left & Top Right Buttons
simultaneously to enter the Config.Menu.
3) The Display will show :
4) Press ROLL UP (Top Left Button) until
SET OPTIONS appears.
6) Press ENTER to go into this part of the menu.
7) The first “Option” of the menu appears
on the Display.
8) Press either ROLL UP or ROLL DOWN to bring
up the next the Option.
9) A new Option appears on the Display.
10) When the desired Option is displayed, press
PARAM (Top Right) or SET (Bottom Right)
button to change the configuration
11) The new Configuration for the selected
Option appears on the Display.
12) Press OUT to exit the Menu.
13) Press ENTER to accept the changes,
or Press OUT if you do not accept the
changes and wish to make further
modifications to the particular Option.
14) The Display now shows:
15) Press OUT again. Display now shows
the Opening Zapi Menu.
If any changes are made to the Configuration, it is necessary to Open and Re-Close
the Key Switch before the Display will show the new, stored, changes.

5.2 DESCRIPTION OF PARAMETERS THAT MAY BE PROGRAMMED
In addition to the Configuration, Parameter settings may be made by Zapi using stand-
ard default settings, settings to Customer Specifications, or the customer may make
changes according to the application, using a Digital Console.
During the setting up procedure on the machine, the Console can remain connected to
the chopper during travel. The Parameters can be modified in real time, during opera-
tion.
Pay attention to the polarity of the Console Connector. Refer to Page 16 of this Manual
for connection details.
The following Parameters can be modified :
1 ACC. DELAY = Determines the acceleration ramp.
2 DECELER DELAY = Determines the deceleration ramp according to the accelera-
tor pedal position.
3 RELEASE BRAKING = Determines the deceleration ramp when the travel request
is released.
4 PEDAL BRAKING = Determines the deceleration ramp when the brake pedal is
operated during travel.
5 INVERSION BRAKING = Determines the deceleration ramp the the Direction
Switch is inverted during travel.
6 TRACTION IMAX = Maximum Current of the Chopper (A).
7 ARMA NOM.CURR. = Nominal Armature Current. This parameter fixes a limit for
the armature current above which the Field Current is at least the Nominal Value
(FIELD NOM.CURR.), regardless of accelerator position.
8 FIELD NOM. CURR. = Nominal Field Current. This parameter fixes the minimum
Field Current when the potentiometer is between 0% and 60% without total conduc-
tion of the Armature. Adjustment should be made with reference to the Data on the
Motor Label. (The indication of Nominal Field Current).
9 MAX SPEED FORW = Maximum Forward Speed, obtained by weakening the Field
Current after it has reached 100% conduction of the Armature. With the Parameter
set at level 0, the armature is in total conduction but the field current does not de-
crease below the Nominal value (low speed).
10 MAX SPEED BACK = Maximum Reverse Speed, obtained by weakening the Field
Current after it has reached 100% conduction of the Armature. With the Parameter
set at level 0, the armature is in total conduction but the field current does not de-
crease below the Nominal value (low speed).
11 WEAK DROPOUT = This Parameter fixes a limit on the Armature Current above
which the Field Current is increased linearly up to the Nominal Field Current (in
proportion to the armature current).
12 CUTBACK SPEED 1 = First Speed Reduction.
13 CUTBACK SPEED 2 = Second Speed Reduction. This Parameter is configured in
the SET OPTION Menu.
14 CUTBACK SPEED 3 = Third Speed Reduction. This Parameter is configured in the
SET OPTION Menu.

15 CREEP SPEED = Minimum Speed. This Parameter sets the minimum voltage
applied to the motor at the start of travel.
16 SEAT MICRO DELAY = Delay time after Seat Microswitch has opened.
17 HYDRO TIME = Operating time for Steering Contactor after controller has oper-
ated. This Parameter is configured in the SET OPTION Menu.
18 BACKING TIME = Operation time of the BACKING Function.
19 BACKING SPEED = Drive Motor Speed during the BACKING function. The chart
on Page 23 shows the different values to which the parameters may be adjusted.
5.3 TABLE OF ADJUSTMENTS
The following Table shows the different values that the SEM2 Parameters may be
adjusted to. A suitable acceleration performance assumes: FIELD CURR. NOM is set
to level 5, and MAX SPEED (Fwd or Rev) is set to level 9.
PARAMETERS
(24/48V VERSION)
PROGRAMMED LEVEL
UNIT 0 1 2 3 4 5 6 7 8 9
ACC. DELAY sec. 0.3 0.6 0.9 1.3 1.6 1.9 2.3 2.5 2.8 3.1
DEC. DELAY * 0 1 2 3 4 5 6 7 8 9
RELEASE BRAKING * 0 1 2 3 4 5 6 7 8 9
PEDAL BRAKNG * 0 1 2 3 4 5 6 7 8 9
INVERS BRAKING * 0 1 2 3 4 5 6 7 8 9
TRACTION I MAX %IMax 82 84 85 87 89 91 93 95 97 100
ARMA CUR. NOM. (ACN) %IMax 32 35 38 41 44 47 50 53 56 58
FIELD CURR. NOM. (FCN) A 12 13 14 15 16 17 18 19 20 21
MAX SPEED FORW. %FCN 100 82 65 55 50 45 40 35 32 30
MAX. SPEED BACK. %FCN 100 82 65 55 50 45 40 35 32 30
WEAK DROP OUT %ACN 35 40 45 50 55 60 65 70 75 80
CUTBACK SPEED 1 %ACC 20 25 30 40 45 50 55 60 70 80
CREEP SPEED %VBatt 3 5 7 9 11 13 15 17 19 21
SEAT MICRO DELAY sec. 0.5 0.7 0.9 1.1 1.4 1.6 1.8 2.0 2.2 2.5
HYDRO TIME sec. 0 0.5 1.0 1.6 2.2 2.7 3.2 3.8 4.4 5.0
BACKING TIME sec. 0.05 0.2 0.3 0.5 0.8 1.0 1.5 2.0 2.5 3.0
BACKING SPEED %VBatt. 32 40 45 52 58 65 72 78 85 90
*= If the current inclines to raise, then also the braking time raises in order to obtain a
smooth braking action. Therefore, the duration of the braking depends on the type of
motor and the operating conditions (laden, unladen, on plane, on gradient).

Flow Chart showing how to make Programme changes using Digital Console fitted with
Eprom CK ULTRA.
1) Opening Zapi Display.
2) Press ENTER to go into the General Menu.
4) Press ENTER to go into the Parameter Change facility.
5) The Display will show the first Parameter.
6) Press either ROLL UP and ROLL DOWN to display
the next parameter.
7) The names of the Parameters appear on the Display.
8) When the desired Parameter appears, the Display will
show a Level Number that will be between 0 and 9.
press either PARAM (Top Right) or SET (Bottom Right)
buttons to change the Level value.
9) The Display will show the New Level.
10) When you are satisfied with the results of the changes
you have made, Press OUT.
11) The Display asks “ ARE YOU SURE ?
12) Press ENTER to accept the changes, or Press OUT
if you do not wish to accept the changes and wish
to make further modifications to the parameters.

5.4 SEM 2 TRACTION STANDARD WIRING DIAGRAMS

5.5 SEQUENCE FOR SEM 2 TRACTION SETTINGS.
When the Key Switch is Closed, if no Alarms or Errors are present, the Console Display
will be showing the Standard Zapi Opening Display.
If the chopper is not Configured to your requirements, follow the Sequence detailed on
Page 20. Remember to re-cycle the Key Switch if you make any changes to the chop-
per’s Configuration. Otherwise follow the sequence detailed below :
1) Select the Options required. (Page 19).
2) Select and set the Battery Voltage.
3) Confirm correct installation of all wires. Use the Console’s TESTER function to
assist.
4) Perform the accelerator signal aquisition procedure using the Console “PROGRAM
VACC”. Procedure is detailed on Page 36.
5) Set the TRACTION IMAX Current, taking into account any Boost requirements.
Use Table on Page 23.
6) Set the Acceleration Delay requirements for the machine. Test the parameters in
both directions.
7) Set the CREEP level starting from level 0. The machine should just move when the
accelerator microswitch is closed. Increase the Level accordingly.
8) Set the Speed Reductions as required. Make adjustments to CUTBACK SP.1, 2, 3.
Check the performance with the accelerator pedal totally depressed. If the machine
is a forklift, check the performance with and without load.
9) RELEASE BRAKING. Operate the machine at full speed. Release the accelerator
pedal. Adjust the level to your requirements. If the machine is a forklift, check the
performance with and without load.
10) INVERSION BRAKING. Operate the machine at 25% full speed. Whilst travelling
INVERT the Direction Switch. Set a soft Level of Inversion Braking. When satisfac-
tory, operate the machine at Full Speed and repeat. If the machine is a Forklift,
repeat the tests and make adjustments with and without load. The unladen full
speed condition should be the most representative condition.
11) PEDAL BRAKING (If used). Operate the machine at full Speed. Press the Pedal
Brake. Set braking level to your requirements.
12) Set MAX SPEED FORW.
13) Set MAX SPEED BACK (Reverse).
14) Set the NOM FIELD CURR. (Nominal Field Current) of the drive motor making
reference to information given on the motor nameplate.
15) Set WEAK DROPOUT (Field Weakening Drop Out Level) according to the require-
ments of the application.
16) If used , set the levels of SEAT MICRO DELAY, HYDRO TIME, BACKING TIME,
BACKING SPEED, to levels as required.
Parameters are described in Page 21.

6 SEM 2 DIAGNOSTICS
As described in the Chopper Diagnostics on Page 9, the following listing shows likely
problems associated with the Flashing RED LED.
N° FLASHES MESSAGE NOTES
1 LOGIC FAILURE Problem with Logic, or General Contactor.
1 MICRO ST6215 KO Problem with the Safety circuit of Microproc-
essor.
1 EEPROM KO Problem with EEPROM or logic.
2 INCORRECT START Starting sequence for travel not correct.
2 HANDBRAKE Switch Open or Failed.
2 FORW+ BACK Double Running request
3 CAPACITOR CHARGE Problem in Power Block.
3 VMN NOT OK VMN Problem with Chopper.
3 VFIELD NOT OK Problem with Field Voltage
4 VACC NOT OK Potentiometer Wiper Voltage too High.
4 PEDAL WIRE KO Problem in the wiring of Foot Pedal.
5 NO FIELD CUR. Open Circuit Field Winding or failure of the
Field Current Sensor.
5 HIGH FIELD CUR. Incorrect connection of Field Winding or fail-
ure of the Field Current Sensor.
5 STBY I HIGH Problem with Armature Current Sensor at
rest.
5 I= 0 EVER Open circuit Armature loop or problem with
Armature Current Sensor.
6 CONTACTOR DRIVER Problem with a Contactor Driver in logic.
6 COIL SHORTED Short Circuit of Contactor Coil.
6 DRIVER SHORTED Short Circuit of Driver supplying the Main
Contactor.
6 CONTACTOR CLOSED Main Contactor contacts CLOSED. Contacts
may be welded or mechanical failure has
occoured.
7 MOTOR TEMPERAT. Motor Temperature Sensor has operated.
7 TH. PROTECTION Thermal Protection of the chopper has
occoured. Temperature was either higher
than 77°C, or lower than -10°C.
32 BATTERY LOW Discharged Battery.

6.1 ANALYSIS OF ALARMS DISPLAYED ON THE CONSOLE
1 LOGIC FAILURE #1
During the initial diagnosis the main Microprocessor performs a check of the Main
Contactor's control circuit, and verifies the condition. If this is not correct this Alarm
is generated.
2 MICRO ST6215 KO
During the initial diagnosis the main Microprocessor tests and verifies the operation
of the safety microprocessor. If not correct this Alarm is generated.
Possible causes:
a) Failure of the safety Microprocessor.
b) The safety Microprocessor has established a condition of danger and has disa-
bled operation of the Main Contactor.
3 EEPROM KO
Fault in the area of memory where the adjustment parameters are stored. This
Alarm inhibits machine operation. If the fault continues when the Key Switch is re-
cycled, replace the logic. If the fault disappears, the previously stored Parameters
will have been replaced by the default parameters.
4 INCORRECT START
Alarm generated by an incorrect Starting Sequence. Possible causes:
a) The ENABLE microswitch has welded or failed.
b) Error in the starting sequence from the operator.
c) Error in the wiring.
5 HANDBRAKE
Hand Brake Switch operated during travel.
6 FORW+ BACK
This check is made continually. The Alarm is generated when forward and reverse
directions are requested simultaneously. Possible causes:
a) Incorrect Wiring.
b) Welding or Failure of a direction switch.
c) Incorrect operation from the operator.
7 CAPACITOR CHARGE
This check is made during the initial diagnosis. This Alarm is generated if the Ca-
pacitors are not charged within 500ms after the Key Switch is closed. Probable
cause is failure inside the power block.
8 VMN NOT OK
This test is performed at rest, with the general Contactor Closed, and also during
operation. At rest if VMN is lower than battery voltage this Alarm is generated.
During operation this Alarm is generated if VMN doesn’t follow the duty-cycle of the
chopper. Possible causes:
a) Incorrect Motor connection.
b) Frame fault of motor to chassis.
c) Defect in the power unit.

9 VFIELD NOT OK
This test is made at standby with the Main Contactor open. In this condition the
voltage on both the connections of field must be to around 1/ 2 VBatt. This alarm is
generated if the field voltage is different from this value. Possible causes:
a) Frame fault on the motor to chassis.
b) Incorrect connection of the field winding to the chopper.
c) Failure of the chopper in the section relative to the field.
10 VACC NOT OK
This Alarm is generated if the accelerator output voltage differs more than 2V from
the acquired minimum during the PROGRAM VACC. Possible causes:
a) The track of the potentiometer has become open.
b) The potentiometer is not wired correctly.
c) The potentiometer itself is defective.
d) The values set in PROGRAM VACC routine have not remained or made cor-
rectly.
11 PEDAL WIRE KO
This Alarm is generated if potentiometer or wiring fault is detected. (NPOT or
PPOT are open circuit).
12 STBY I HIGH
This test is made during the initial diagnosis and at standby. The test verifies that
the current is zero. This Alarm disables the machine. Possible causes:
a) Defective current sensor.
b) Logic failure. First replace the logic. If fault remains replace the power unit.
13 I = 0 EVER
This check is made during travel. If the current is not higher than a preset minimum
value, this Alarm is generated and the machine disabled. Possible causes:
see STBY I HIGH. Check the motor armature (brush connections).
14 HIGH FIELD CURR, NO FIELD CUR
Problem detected with the field winding current. Possible causes:
a) Tailure of the field current sensor.
b) Field cables not connected or incorrectly connected.
c) Open circuit Field Winding.
d) Failure of the Field Power Unit.
e) The Alarm No FIELD CURR could also be generated if the safety microprocessor
detects a problem.
15 CONTACTOR DRIVER, COIL SHORTED, DRIVER SHORTED
These Alarms are generated if there is a problem with the Main Contactor. Possible
causes:
a) the coil of the contactor is either short-circuit, open circuit, or not connected
b) The Contactor Coil Driver is short-circuit.
c) defect in the wiring to the contactor, or logic failure.

16 CONTACTOR CLOSED
This check is made during the initial diagnosis. With the coil of the Main Contactor
de-energised, the capacitors should not be charged, unless there is divert resistor
across the power poles. Possible causes:
a) The contactor power poles are welded .
b) This alarm could be generated if the Main Contactor has opened, but there is a
problem with either the field circuit, or a problem detected by the safety micro-
processor.
17 MOTOR TEMPERAT
The temperature of the motor has become higher than the threshold set by the
motor sensor. When this Alarm is generated, the motor speed is reduced. If this
alarm appears with a cold motor:
a) Check the connection to the temperature sensor.
b) Check that there is no problem with the temperature sensor.
c) Check there is no problem with the motor temperature.
18 TH PROTECTION
If the temperature of the chopper rises higher than 77°C, this alarm is generated.
The chopper current is reduced in proportion to the increase in temperature.
At 92°C the chopper totally stops. If the temperature of the chopper is < -10°C, this
Alarm is also generated and the current is reduced by 80 %. If this alarm is dis-
played when the chopper is temperature is the same as ambient or better than zero
degrees:
a) Check the connection of the temperature sensor.
b) The temperature sensor may be defective.
c) The logic may be defective.
19 BATTERY LOW
This Alarm is generated when the battery becomes 50% discharged from the

nominal value.
6.2 TESTER. DESCRIPTION OF THE FUNCTIONS
The most important input or output signals can be measured in real time using the
TESTER function of the console. The Console acts as a multimeter able to read volt-
age, current and temperature. The following definition listing shows the relative meas-
urements :
1) BATTERY VOLTAGE: level of battery voltage measured at the input to the key
switch.
2) BATTERY CHARGE: the percentage Charge level of the battery.
3) MOTOR VOLTAGE: the voltage appearing across the drive motor. It is measured
between B+ and VMN.
4) MOTOR CURRENT: the current flowing in the drive motor armature.
5) FIELD CURRENT: the current flowing in the drive motor field winding.
6) VMN: the voltage effectively dropped across the MOS. It is measured between
-BATT and VMN.
7) TR. CHOPPER TEMP: the temperature measured on the aluminum heat sink
holding the MOSFET devices.
8) ACCELERATOR: the voltage of the accelerator potentiometer wiper (CPOT).
The voltage level is shown on the Left Hand Side of the Console Display and the
value in percentage is shown on the Right Hand Side.
9) FORWARD SWITCH: the level of the Forward direction digital entry MA (pin E3).
ON/+ VB = active entry of closed switch.
OFF / GND = non active entry of open switch.
10) BACKWARD SWITCH: the level of the Reverse direction digital entry MI (pin E2).
11) ENABLE SWITCH: the level of Enable Switch digital input.
12) SEAT SWITCH: the level of the Seat Microswitch digital entry (pin E6).
ON/+ VB = active entry of closed seat switch.
OFF/ GND = non active entry of open seat switch.
13) HAND BRAKE: the level of the Handbrake Microswitch (pin B5).
ON/+ VB = active entry of Handbrake switch.
OFF/ GND = non active entry of microswitch.
14) CUTBACK SWITCH 1: the level of the Speed Reduction 1 Microswitch (pin E4).
ON/ +12 = active entry of speed reduction microswitch.
15) CUTBACK SWITCH 2: the level of the Speed Reduction 2 Microswitch (pin B4).

16) CUTBACK SWITCH 3: the level of the Speed Reduction 3 Microswitch (Pin L4).
OFF / GND = non active entry of microswitch.
17) BRAKE SWITCH: the level of the Pedal Brake Microswitch (pin E5).
ON/+ VB = active entry of Brake pedal microswitch.
OFF / GND = non active entry of microswitch.
18) BACKING FUNCTION: the level of the Backing Microswitch inputs (pins L2 or L3).
ON/+ VB = active switch entry.
OFF / GND = non active switch entry.
19) MOTOR TEMPERAT.: the level of the Motor Temperature Sensor (pin E7).
ON / +VB = temperature of the motor is too high.
OFF/ GND = temperature of the motor within the limits. Sensor is not operating.
Flow Chart showing how to use the TESTER function of the Digital Console.
2) Press ENTER to go into the General menu.
4) Press ROLL UP or ROLL DOWN button until
TESTER MENU appear on the display.
5) The Display shows :
6) Press ENTER to go into the TESTER function.
7) The first variable to be tested is shown on the Display.
8) Press either ROLL UP or ROLL DOWN buttons until your
desired variable for measurement appears on the Display.
9) When you have finished, Press OUT.
10) The Display shows :
11) Press OUT again. Console now shows the
Opening Zapi Display.
Remember it is not possible to make any changes using TESTER. All you can do is
measure as if you were using a pre-connected multimeter.

6.3 DESCRIPTION OF THE CONSOLE SAVE FUNCTION
The SAVE function allows the operator to transmit the Parameter values and
Configuration data of the chopper into the Console memory. It is possible to
load 64 different programmes.
The information saved in the Console memory can then be reloaded into another
chopper using the RESTORE function.
The data that is available via the SAVE function is as follows:
- All Parameter Values (PARAMETER CHANGE).
- Options (SET. OPTIONS).
- The Level of the Battery (ADJUST BATTERY).
Flow Chart showing how to use the SAVE function of the Digital Console.
SAVE PARAM. appears on the display
6) Press ENTER to go into the SAVE function.
7) If this facility has been used before the type
of chopper data stored appears on the top Main with
a 2 digit reference.
8) Keep pressing either ROLL UP or ROLL DOWN keys until
the second Main indicates a FREE storage facility.
9) Press ENTER to commence SAVE routine.
10) You can see the items that are being stored whilst
the SAVE routine is happening.
11) When finished, the Console shows :
13) Press OUT to return to the Opening Zapi Display.

6.4 DESCRIPTION OF CONSOLE RESTORE FUNCTION.
The RESTORE PARAM function allows transfer of the Console’s stored data into the
memory of the chopper. This is achieved in a fast and easy way using the method
previously used with the SAVE PARAM. function.
The data that is available via the RESTORE PARAM. function is as follows :
- All Parameter Values (PARAMETER CHANGE).
- Options (SET OPTIONS)
- The level of the Battery (ADJUST BATTERY)
ATTENTION: When the RESTORE operation is made, all data in the chopper memory
will be writtten over and replace with data being restored.
Flow Chart showing how tto use the RESTORE function of the Digital Console.
RESTORE PARAM. appears on the display.
6) Press ENTER to go into the RESTORE PARAM. function.
7) The Display shows the type of Model stored,
with a Code Number.
8) Keep pressing either ROLL UP and ROLL DOWN buttons
until the desired model appears on the Display.
9) Press ENTER to commence the Restore operation.
10) The Display will ask “ARE YOU SURE”.
Press ENTER for YES, or OUT for No.
11) You can see the items that are being stored in
the chopper memory whilst the RESTORE
routine is happening.
12) When finished the Console displays :
13) Press OUT to return to the Opening Zapi Display .

6.5 DESCRIPTION OF ALARMS MENU.
The microprocessor in the chopper remembers the last five Alarms that have occurred.
Items remembered relative to each Alarm are : the code of the alarm, the number of
times the particular Alarm occurred, the Hour Meter count, and the chopper tempera-
ture.
This function permits a deeper diagnosis of problems as the recent history can now be
accessed.
Flow Chart showing how to use the ALARMS function via the Digital Console.
PARAMETER CHANGE appears on the display.
5) The Display will show:
6) Press ENTER to go into the ALARMS function.
7) The Display will show the most recent Alarm.
8) Each press of the ROLL UP button brings up following Alarms.
Pressing ROLL DOWN returns to the most recent.
9) If an Alarm has not occurred, the Display will show:
ALARM NULL.
10) When you have finished looking at the Alarms, press OUT
to exit the ALARMS menu.
11) The Display will ask CLEAR LOGBOOK ?
12) Press ENTER for yes, or OUT for NO.
13) Press OUT to return to the Opening Zapi Display.

6.6 DESCRIPTION OF CONSOLE PROGRAM VACC FUNCTION.
This function looks for and remembers the minimum and maximum potentiometer wiper
voltage over the full mechanical range of the pedal. It enables compensation for non
symmetry of the mechanical system between directions.
The operation is performed by operating the pedal after entering the PROGRAM VACC
function.
Flow Chart showing how to use the PROGRAM VACC function of the Digital Console.
2) Press ENTER tto go into the General Menu.
PROGRAM VACC appears on the display.
5) Tthe Display will show :
6) Press ENTER to go into the PROGRAM VACC routine.
7) The Display will show the minimum and maximum
values of potentiometer wiper output. Both directions can
be shown.
8) Press ENTER to clear these values. Display will show 0.0.
9) Select Forward Direction, close any interlock switches
that may be in the system.
10) Slowly depress the accelerator pedal (or tiller butterfly) to
its maximum value. The new minimum and maximum
voltages will be displayed on the Console plus an
arrow indicating the direction.
11) Select the Reverse Direction and repeat Item 10.
12) When finished , press OUT.
13) The Display will ask : ARE YOU SURE ?.
14) Press ENTER for yes, or OUT for NO.
15) Press OUT again to return to the Opening Zapi Menu.

7 RECOMMENDED SPARE PARTS FOR SEM 2
Part Number Description
C16504 Protected 300A Air Fuse.
C16503 Protected 200A Air Fuse
C16520 6.3A 20mm Control Circuit Fuse
P99060 Red LED
C12373 9 Way Molex Connector
C12769 Insert for Molex Connectors
C29619 SW 180 24V CO
Single Pole Contactor
C29610 SW 180 48V CO
Single Pole Contactor

8 PERIODIC MAINTENANCE TO BE REPEATED
AT TIMES INDICATED.
Check the wear and condition of the Contactors’ moving and fixed contacts.
Electrical Contacts should be checked every 3 months.
Check the Foot pedal or Tiller microswitch. Using a suitable test meter, confirm that
there is no electrical resistance between the contacts by measuring the volt drop be-
tween the terminals. Switches should operate with a firm click sound.
Microswitches should be checked every 3 months.
Check the Battery cables, cables to the chopper, and cables to the motor. Ensure the
insulation is sound and the connections are tight.
Cables should be checked every 3 months.
Check the mechanical operation of the pedal or tiller . Are the return springs ok. Do
the potentiometers wind up to their full or programmed level.
Check every 3 months.
Check the mechanical operation of the Contactor(s). Moving contacts should be free
to move without restriction.
Check every 3 months.
Checks should be carried out by qualified personnel and any replacement parts used
should be original. Beware of NON ORIGINAL PARTS.
The installation of this electronic controller should be made according to the diagrams
included in this Manual. Any variations or special requirements should be made after
consulting a Zapi Agent. The supplier is not responsible for any problem that arises
from wiring methods that differ from information included in this Manual.
During periodic checks, if a technician finds any situation that could cause damage or
compromise safety, the matter should be bought to the attention of a Zapi Agent imme-
diately. The Agent will then take the decision regarding operational safety of the ma-
chine.
Remember that Battery Powered Machines feel no pain.
NEVER USE A VEHICLE WITH A FAULTY ELECTRONIC CONTROLLER.

Zapi sem 2 manual

More Related Content

What's hot (20)

Similar to Zapi sem 2 manual (20)

Recently uploaded (20)

Zapi sem 2 manual