![CMOS VLSI Design 4th Ed.
1: Circuits & Layout 3
A Brief History
1958: First integrated circuit
– Flip-flop using two transistors
– Built by Jack Kilby at Texas
Instruments
2010
– Intel Core i7 processor
• 2.3 billion transistors
– 64 Gb Flash memory
• > 16 billion transistors
Courtesy Texas Instruments
[Trinh09]
© 2009 IEEE](https://image.slidesharecdn.com/lect1-cktlay-240914085626-e6d1f52f/85/Circuits-layouts-design-in-VLSI-design-and-Testing-3-320.jpg)
![CMOS VLSI Design 4th Ed.
1: Circuits & Layout 4
Growth Rate
53% compound annual growth rate over 50 years
– No other technology has grown so fast so long
Driven by miniaturization of transistors
– Smaller is cheaper, faster, lower in power!
– Revolutionary effects on society
[Moore65]
Electronics Magazine](https://image.slidesharecdn.com/lect1-cktlay-240914085626-e6d1f52f/85/Circuits-layouts-design-in-VLSI-design-and-Testing-4-320.jpg)
![CMOS VLSI Design 4th Ed.
1: Circuits & Layout 8
1970’s processes usually had only nMOS transistors
– Inexpensive, but consume power while idle
1980s-present: CMOS processes for low idle power
MOS Integrated Circuits
Intel 1101 256-bit SRAM Intel 4004 4-bit Proc
[Vadasz69]
© 1969 IEEE.
Intel
Museum.
Reprinted
with
permission.](https://image.slidesharecdn.com/lect1-cktlay-240914085626-e6d1f52f/85/Circuits-layouts-design-in-VLSI-design-and-Testing-8-320.jpg)
![CMOS VLSI Design 4th Ed.
1: Circuits & Layout 9
Moore’s Law: Then
1965: Gordon Moore plotted transistor on each chip
– Fit straight line on semilog scale
– Transistor counts have doubled every 26 months
Integration Levels
SSI: 10 gates
MSI: 1000 gates
LSI: 10,000 gates
VLSI: > 10k gates
[Moore65]
Electronics Magazine](https://image.slidesharecdn.com/lect1-cktlay-240914085626-e6d1f52f/85/Circuits-layouts-design-in-VLSI-design-and-Testing-9-320.jpg)
Circuits layouts design in VLSI design and Testing
- 2. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 2 Outline A Brief History CMOS Gate Design Pass Transistors CMOS Latches & Flip-Flops Standard Cell Layouts Stick Diagrams
- 3. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 3 A Brief History 1958: First integrated circuit – Flip-flop using two transistors – Built by Jack Kilby at Texas Instruments 2010 – Intel Core i7 processor • 2.3 billion transistors – 64 Gb Flash memory • > 16 billion transistors Courtesy Texas Instruments [Trinh09] © 2009 IEEE
- 4. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 4 Growth Rate 53% compound annual growth rate over 50 years – No other technology has grown so fast so long Driven by miniaturization of transistors – Smaller is cheaper, faster, lower in power! – Revolutionary effects on society [Moore65] Electronics Magazine
- 5. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 5 Annual Sales >1019 transistors manufactured in 2008 – 1 billion for every human on the planet
- 6. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 6 Invention of the Transistor Vacuum tubes ruled in first half of 20th century Large, expensive, power-hungry, unreliable 1947: first point contact transistor – John Bardeen and Walter Brattain at Bell Labs – See Crystal Fire by Riordan, Hoddeson AT&T Archives. Reprinted with permission.
- 7. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 7 Transistor Types Bipolar transistors – npn or pnp silicon structure – Small current into very thin base layer controls large currents between emitter and collector – Base currents limit integration density Metal Oxide Semiconductor Field Effect Transistors – nMOS and pMOS MOSFETS – Voltage applied to insulated gate controls current between source and drain – Low power allows very high integration
- 8. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 8 1970’s processes usually had only nMOS transistors – Inexpensive, but consume power while idle 1980s-present: CMOS processes for low idle power MOS Integrated Circuits Intel 1101 256-bit SRAM Intel 4004 4-bit Proc [Vadasz69] © 1969 IEEE. Intel Museum. Reprinted with permission.
- 9. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 9 Moore’s Law: Then 1965: Gordon Moore plotted transistor on each chip – Fit straight line on semilog scale – Transistor counts have doubled every 26 months Integration Levels SSI: 10 gates MSI: 1000 gates LSI: 10,000 gates VLSI: > 10k gates [Moore65] Electronics Magazine
- 10. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 10 And Now…
- 11. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 11 Feature Size Minimum feature size shrinking 30% every 2-3 years
- 12. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 12 Corollaries Many other factors grow exponentially – Ex: clock frequency, processor performance
- 13. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 13 CMOS Gate Design Activity: – Sketch a 4-input CMOS NOR gate A B C D Y
- 14. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 14 Complementary CMOS Complementary CMOS logic gates – nMOS pull-down network – pMOS pull-up network – a.k.a. static CMOS pMOS pull-up network output inputs nMOS pull-down network Pull-up OFF Pull-up ON Pull-down OFF Z (float) 1 Pull-down ON 0 X (crowbar)
- 15. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 15 Series and Parallel nMOS: 1 = ON pMOS: 0 = ON Series: both must be ON Parallel: either can be ON (a) a b a b g1 g2 0 0 a b 0 1 a b 1 0 a b 1 1 OFF OFF OFF ON (b) a b a b g1 g2 0 0 a b 0 1 a b 1 0 a b 1 1 ON OFF OFF OFF (c) a b a b g1 g2 0 0 OFF ON ON ON (d) ON ON ON OFF a b 0 a b 1 a b 1 1 0 1 a b 0 0 a b 0 a b 1 a b 1 1 0 1 a b g1 g2
- 16. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 16 Conduction Complement Complementary CMOS gates always produce 0 or 1 Ex: NAND gate – Series nMOS: Y=0 when both inputs are 1 – Thus Y=1 when either input is 0 – Requires parallel pMOS Rule of Conduction Complements – Pull-up network is complement of pull-down – Parallel -> series, series -> parallel A B Y
- 17. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 17 Compound Gates Compound gates can do any inverting function Ex: (AND-AND-OR-INVERT, AOI22) Y A B C D A B C D A B C D A B C D A B C D B D Y A C A C A B C D B D Y (a) (c) (e) (b) (d) (f)
- 18. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 18 Example: O3AI Y A B C D A B Y C D D C B A
- 19. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 19 Signal Strength Strength of signal – How close it approximates ideal voltage source VDD and GND rails are strongest 1 and 0 nMOS pass strong 0 – But degraded or weak 1 pMOS pass strong 1 – But degraded or weak 0 Thus nMOS are best for pull-down network
- 20. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 20 Pass Transistors Transistors can be used as switches g = 0 s d g = 1 s d 0 strong 0 Input Output 1 degraded 1 g = 0 s d g = 1 s d 0 degraded 0 Input Output strong 1 g = 1 g = 1 g = 0 g = 0 1 g s d g s d
- 21. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 21 Transmission Gates Pass transistors produce degraded outputs Transmission gates pass both 0 and 1 well g = 0, gb = 1 a b g = 1, gb = 0 a b 0 strong 0 Input Output 1 strong 1 g gb a b a b g gb a b g gb a b g gb g = 1, gb = 0 g = 1, gb = 0
- 22. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 22 Tristates Tristate buffer produces Z when not enabled EN A Y 0 0 Z 0 1 Z 1 0 0 1 1 1 A Y EN A Y EN EN
- 23. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 23 Nonrestoring Tristate Transmission gate acts as tristate buffer – Only two transistors – But nonrestoring • Noise on A is passed on to Y A Y EN EN
- 24. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 24 Tristate Inverter Tristate inverter produces restored output – Violates conduction complement rule – Because we want a Z output A Y EN A Y EN = 0 Y = 'Z' Y EN = 1 Y = A A EN
- 25. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 25 Multiplexers 2:1 multiplexer chooses between two inputs S D1 D0 Y 0 X 0 0 0 X 1 1 1 0 X 0 1 1 X 1 0 1 S D0 D1 Y
- 26. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 26 Gate-Level Mux Design How many transistors are needed? 20 1 0 (too many transistors) Y SD SD 4 4 D1 D0 S Y 4 2 2 2 Y 2 D1 D0 S
- 27. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 27 Transmission Gate Mux Nonrestoring mux uses two transmission gates – Only 4 transistors S S D0 D1 Y S
- 28. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 28 Inverting Mux Inverting multiplexer – Use compound AOI22 – Or pair of tristate inverters – Essentially the same thing Noninverting multiplexer adds an inverter S D0 D1 Y S D0 D1 Y 0 1 S Y D0 D1 S S S S S S
- 29. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 29 4:1 Multiplexer 4:1 mux chooses one of 4 inputs using two selects – Two levels of 2:1 muxes – Or four tristates S0 D0 D1 0 1 0 1 0 1 Y S1 D2 D3 D0 D1 D2 D3 Y S1S0 S1S0 S1S0 S1S0
- 30. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 30 D Latch When CLK = 1, latch is transparent – D flows through to Q like a buffer When CLK = 0, the latch is opaque – Q holds its old value independent of D a.k.a. transparent latch or level-sensitive latch CLK D Q Latch D CLK Q
- 31. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 31 D Latch Design Multiplexer chooses D or old Q 1 0 D CLK Q CLK CLK CLK CLK D Q Q Q
- 32. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 32 D Latch Operation CLK = 1 D Q Q CLK = 0 D Q Q D CLK Q
- 33. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 33 D Flip-flop When CLK rises, D is copied to Q At all other times, Q holds its value a.k.a. positive edge-triggered flip-flop, master-slave flip-flop Flop CLK D Q D CLK Q
- 34. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 34 D Flip-flop Design Built from master and slave D latches QM CLK CLK CLK CLK Q CLK CLK CLK CLK D Latch Latch D Q QM CLK CLK
- 35. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 35 D Flip-flop Operation CLK = 1 D CLK = 0 Q D QM QM Q D CLK Q
- 36. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 36 Race Condition Back-to-back flops can malfunction from clock skew – Second flip-flop fires late – Sees first flip-flop change and captures its result – Called hold-time failure or race condition CLK1 D Q1 Flop Flop CLK2 Q2 CLK1 CLK2 Q1 Q2
- 37. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 37 Nonoverlapping Clocks Nonoverlapping clocks can prevent races – As long as nonoverlap exceeds clock skew We will use them in this class for safe design – Industry manages skew more carefully instead 1 1 1 1 2 2 2 2 2 1 QM Q D
- 38. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 38 Gate Layout Layout can be very time consuming – Design gates to fit together nicely – Build a library of standard cells Standard cell design methodology – VDD and GND should abut (standard height) – Adjacent gates should satisfy design rules – nMOS at bottom and pMOS at top – All gates include well and substrate contacts
- 39. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 39 Example: Inverter
- 40. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 40 Example: NAND3 Horizontal N-diffusion and p-diffusion strips Vertical polysilicon gates Metal1 VDD rail at top Metal1 GND rail at bottom 32 by 40
- 41. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 41 Stick Diagrams Stick diagrams help plan layout quickly – Need not be to scale – Draw with color pencils or dry-erase markers c A VDD GND Y A VDD GND B C Y INV metal1 poly ndiff pdiff contact NAND3
- 42. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 42 Wiring Tracks A wiring track is the space required for a wire – 4 width, 4 spacing from neighbor = 8 pitch Transistors also consume one wiring track
- 43. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 43 Well spacing Wells must surround transistors by 6 – Implies 12 between opposite transistor flavors – Leaves room for one wire track
- 44. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 44 32 40 Area Estimation Estimate area by counting wiring tracks – Multiply by 8 to express in
- 45. CMOS VLSI Design 4th Ed. 1: Circuits & Layout 45 Example: O3AI Sketch a stick diagram for O3AI and estimate area – Y A B C D A VDD GND B C Y D 6 tracks = 48 5 tracks = 40