L6 and L7 full wave rectifier, PIV.ppt
- 1. • Zener effect and Zener diode – When a Zener diode is reverse-biased, it acts at the breakdown region, when it is forward biased, it acts like a normal PN junction diode • Avalanche Effect – Gain kinetic energy – hit another atom – produce electron and hole pair Recall-Lecture 5
- 2. • Voltage Regulator using Zener Diode 1. The zener diode holds the voltage constant regardless of the current 2. The load resistor sees a constant voltage regardless of the current The remainder of VPS drops across Ri
- 3. FULL WAVE RECTIFIER • Center-Tapped • Bridge
- 4. Positive cycle, D2 off, D1 conducts; Vo – Vs + V = 0 Vo = Vs - V Full-Wave Rectification – circuit with center-tapped transformer Since a rectified output voltage occurs during both positive and negative cycles of the input signal, this circuit is called a full- wave rectifier. Also notice that the polarity of the output voltage for both cycles is the same Negative cycle, D1 off, D2 conducts; Vo – Vs + V = 0 Vo = Vs - V
- 5. Vs = Vpsin t V -V Notice again that the peak voltage of Vo is lower since Vo = Vs - V Vp • Vs < V, diode off, open circuit, no current flow,Vo = 0V
- 6. Positive cycle, D1 and D2 conducts, D3 and D4 off; + V + Vo + V – Vs = 0 Vo = Vs - 2V Full-Wave Rectification –Bridge Rectifier Negative cycle, D3 and D4 conducts, D1 and D2 off + V + Vo + V – Vs = 0 Vo = Vs - 2V Also notice that the polarity of the output voltage for both cycles is the same
- 7. • A full-wave center-tapped rectifier circuit is shown in Fig. 3.1. Assume that for each diode, the cut-in voltage, V = 0.6V and the diode forward resistance, rf is 15. The load resistor, R = 95 . Determine: – peak output voltage, Vo across the load, R – Sketch the output voltage, Vo and label its peak value. 25: 1 125 V (peak voltage) ( sine wave )
- 8. • SOLUTION • peak output voltage, Vo Vs (peak) = 125 / 25 = 5V V +ID(15) + ID (95) - Vs(peak) = 0 ID = (5 – 0.6) / 110 = 0.04 A Vo (peak) = 95 x 0.04 = 3.8V 3.8V Vo t
- 9. Duty Cycle: The fraction of the wave cycle over which the diode is conducting.
- 10. EXAMPLE 3.1 – Half Wave Rectifier Determine the currents and voltages of the half-wave rectifier circuit. Consider the half- wave rectifier circuit shown in Figure. Assume and . Also assume that Determine the peak diode current, maximum reverse-bias diode voltage, the fraction of the wave cycle over which the diode is conducting. A simple half-wave battery charger circuit -VR + VB + 18.6 = 0 VR = 24.6 V - VR + + -
- 12. The peak inverse voltage (PIV) of the diode is the peak value of the voltage that a diode can withstand when it is reversed biased
- 13. Type of Rectifier PIV Half Wave Peak value of the input secondary voltage, Vs (peak) Full Wave : Center-Tapped 2Vs(peak) - V Full Wave: Bridge Vs(peak)- V
- 14. Example: Half Wave Rectifier Given a half wave rectifier with input primary voltage, Vp = 80 sin t and the transformer turns ratio, N1/N2 = 6. If the diode is ideal diode, (V = 0V), determine the value of the peak inverse voltage. 1. Get the input of the secondary voltage: 80 / 6 = 13.33 V 1. PIV for half-wave = Peak value of the input voltage = 13.33 V
- 15. EXAMPLE 3.2 Calculate the transformer turns ratio and the PIV voltages for each type of the full wave rectifier a) center-tapped b) bridge Assume the input voltage of the transformer is 220 V (rms), 50 Hz from ac main line source. The desired peak output voltage is 9 volt; also assume diodes cut-in voltage = 0.6 V.
- 16. Solution: For the centre-tapped transformer circuit the peak voltage of the transformer secondary is required The peak output voltage = 9V Output voltage, Vo = Vs - V Hence, Vs = 9 + 0.6 = 9.6V Peak value = Vrms x 2 So, Vs (rms) = 9.6 / 2 = 6.79 V The turns ratio of the primary to each secondary winding is The PIV of each diode: 2Vs(peak) - V = 2(9.6) - 0.6 = 19.6 - 0.6 = 18.6 V
- 17. Solution: For the bridge transformer circuit the peak voltage of the transformer secondary is required The peak output voltage = 9V Output voltage, Vo = Vs - 2V Hence, Vs = 9 + 1.2 = 10.2 V Peak value = Vrms x 2 So, Vs (rms) = 10.2 / 2 = 7.21 V The turns ratio of the primary to each secondary winding is The PIV of each diode: Vs(peak)- V = 10.2 - 0.6 = 9.6 V