Microwave Engineering Lecture Notes

 COPYRIGHT IS NOT RESERVED BY AUTHORS.
 AUTHORS ARE NOT RESPONSIBLE FOR ANY LEGAL
ISSUES ARISING OUT OF ANY COPYRIGHT DEMANDS
 AND/OR REPRINT ISSUES CONTAINED IN THIS
MATERIALS.
 THIS IS NOT MEANT FOR ANY COMMERCIAL PURPOSE &
ONLY MEANT FOR PERSONAL USE OF STUDENTS
FOLLOWING SYLLABUS PRINTED NEXT PAGE.
 READERS ARE REQUESTED TO SEND ANY TYPING
ERRORS CONTAINED, HEREIN.

MICROWAVE ENGINEERING (3-1-0)
Module-I (14 Hours)
High Frequency Transmission line and Wave guides: The Lumped-Element Circuit model for a
Transmission line. Wave propagation. The lossless line. Field Analysis of Co-ax Transmission Lines. R, L,
C, G parameters of Co-axial & Two wire Transmission lines, Terminated lossless transmission line, Lowloss
line, The Smith Chart. Solution of Transmission line problems using Smith chart. Single Stub and Double
Stub matching.
Waveguides:
Rectangular waveguides, Field solution for TE and TM modes, Design of Rectangular waveguides to
support Dominant TE only.
Module-II
(12 Hours)
TEM mode in Co-ax line. Cylindrical waveguides- Dominant mode. Design of cylindrical waveguides to
support dominant TE mode. Microwave Resonator: Rectangular waveguides Cavities, Resonant frequencies
and of cavity supporting. Dominant mode only.
Excitation of waveguides and resonators (in principle only). Waveguides Components: Power divider and
Directional Couplers: Basic properties. The TJunction power divider, Waveguide-Directional Couplers.
Fixed and Precision variable Attenuator, Isolator, Circulator (Principle of Operation only).
Module-III (10 Hours)
Microwave Sources: Reflex Klystron: Velocity Modulation, Power output and frequency versus Reflector
voltage Electronic Admittance. MultiCavity Magnetron: Principle of operation, Rotating field, Π-mode of
operation, Frequency of oscillation. The ordinary type (O-type) traveling wave tube- Construction features,
principle of operation as an amplifier, Gunn oscillator (principle).
Module-IV (6 Hours)
Microwave Propagation: Line of sight propagation. Attenuation of microwaves by Atmospheric gases, water
vapors & precipitates.
Text Books:
1. Microwave Engineering by D.M.Pozor, 2nd
Edition, John Willy & Sons. Selected portions from Chapters
2,3,4,6,7&9.
2. Principles of Microwave Engineering by Reich, Oudong and Others.
3. Microwave Devices and Circuits, 3rd Edition, Sammuel Y, Liao, Perason.

Microwave
The signal deals with very small wave wavelength is called microwave signal, this implies
signal has:
Wavelength (ƛ) =speed/frequency
With due increase in frequency the wavelength decrease and vice versa; we can say that
wavelength is inversely proportional to frequency.
In communication system,it generally consist of three main components: Transmitter,
Receiver and Channel.
There are two type mediums: transmission line & waveguide.
Transmission line used for small range frequencies. Waveguide used for large range
frequencies.
Transmission Line (TL)
 The wave is bounded at low frequency in transmission line and hence called low pass
filter.
 Transmission line mainly supports electromagnetic field.
Types of Transmission Line:
 Coaxial cable
 Parallel wire cable
 Microstrip line
Lumped Element Circuit Model of Transmission Line
 A current carrying conductor produce a magnetic field i.e., inductance which opposes
the flow of current hence resistance ‘R’ is in series with inductance ‘L’.
 Because of dielectric separation; there exist a capacitance and the loss in the dielectric
medium give rise to conductance.
R= Resistance of the conductor (Ω/m)
L= Self Inductance of the conductor (µ/m)
C= Capacitance across the conductor (F/m)
G= Dielectric Loss between conductor (Ʊ/m)

Applying KVL in the loop;
v(z, t)= R ∆z I(z, t) + L ∆z (d I(z, t)/dt) + v(z + ∆z, t)
v(z, t) - v(z + ∆z, t)= R ∆z I(z, t) + L ∆z (d I(z, t)/dt)
(v(z, t) - v(z + ∆z, t))/ ∆z= R I(z, t) + L (d I(z, t)/dt)
Taking limit;
lim (v(z, t) - v(z + ∆z, t))/ ∆z= lim R I(z, t) + L (d I(z, t)/dt)
∆z0 ∆z0
-dv(z, t)/dz= R I(z, t) + L dI(z, t)/dtC
-dV/dz= RI + LdI/dt -------------①
Applying KCL at first node
I(z, t)= I(z + ∆z, t) + ∆I
I(z, t)= ∆I1 + ∆I2 + I(z + ∆z, t)
I(z, t)= G ∆z V(z + ∆z, t) + C ∆z (d V(z + ∆z, t)/dt) + I(z + ∆z, t)
I(z, t) - I(z + ∆z, t)= G ∆z V(z + ∆z, t) + C ∆z (d V(z + ∆z, t)/dt)
(I(z, t) - I(z + ∆z, t))/∆z= G V(z + ∆z, t) + C (d V(z + ∆z, t)/dt)
lim (I(z, t) - I(z + ∆z, t))/∆z= lim G V(z + ∆z, t) + C (d V(z + ∆z, t)/dt)
∆z 0 ∆z 0
-d I(z, t)/dz= G V(z,t) + C (d V(z, t)/dt)
-d I/dz= G V + C d V/dt -------------②

In equation ① & ②
V= V(z, t)= Re{Vs(z)ejὠt
}
I= I(z, t)= Re{Is(z)ejὠt
}
Putting V & I in equation ①
-d V/dz= R I + L d I/dt
-d [Re{Vs(z)ejὠt
}]/dz= R [Re{Is(z)ejὠt
}] + L d [Re{Is(z)ejὠt
}]/dt
- Re{d Vs(z)ejὠt
/dz}= R Is(z) [Re{ ejὠt
}] + L [Re{j ὠ Is(z)ejὠt
}]
-d Vs(z)/dz= (R + jὠL)Is(z) -------------③
Similarly,
-d Is(z)/dz= (G + jὠC)Vs(z) -------------④
Equation ③ & ④ are called Telegraphers Equation or low frequency equation.
The transmission line discussed so far were of lossy type in which the conductors comprising
the line are imperfect ( c   )and the dielectric in which the conductors are embedded is
lossy ( 0c  ).
Having considered this general case , we may now consider two special cases:
1. Lossless line(R=0=G)
2. Distortionless line(R/l=G/c)
Case-1:Lossless line(R=0=G):- The transmission line is said to be lossless if the
conductors of the line are perfect c   and the dielectric separating between them is
lossless( 0c  ).
For such a line R=0=G .This is the necessary condition for a line to be lossless.
Hence for this line the attenuation constant α=0. But the propagation constant
γ=√(R+j⍵L)(G+ j⍵C)
But we also know that γ=α+jβ.
so on solving we get:-
√{(RG +R j⍵C +G j⍵L+j2
⍵2
LC=jβ (∵α=0)

So we get √(j2
⍵2
LC)=jβ
this shows that the phase constant β= ⍵√LC and for the characteristic impedance
Z0=√{(R+j⍵L)/(G+ j⍵C)}
so Z0= √(L/C)
and the phase velocity vp=⍵/β=1/√(LC)=fλ
Case-2:Distortionless Line(R/L=G/C):- A distortionless line is the one in which the
attenuation constant α is frequency independent while the phase constant β is linearly
dependent on frequency.
From the expression for α and β a distortionless line results if the parameters are such:-
R/L=G/C
So γ=√( R+j⍵L)(G+ j⍵C)
Hence γ=√RG(1+j⍵L/R)(1+j⍵C/G)
=√RG(1+ j⍵C/G)2
=α+jβ
so α= √RG and β=⍵√LC
The above values shows that α is not dependent on frequency and β is a linearly
dependent on frequency.
Also characteristic impedance=Z0=√(R+j⍵L)/(G+ j⍵C)
Z0=√[R(1+j⍵L/R)]/[G(1+j⍵C/G)]
Z0=√R/G=√L/C
Also the phase velocity vp=⍵/β=1/√LC=fλ
Or λ=1/f√LC
Microwave Line:- A microwave line is the one where the parameters are such :-R<<⍵L
and G<<⍵C
So the characteristic impedance Z0=√(R+j⍵L)/(G+ j⍵C)
So substituting the parameters we get:- Z0=√L/C
And propagation constant γ=√( R+j⍵L)(G+ j⍵C)
So γ=√j⍵L(1+R/j⍵L) j⍵c(1+G/j⍵C)
=j⍵√LC[(1+R/j⍵L)1/2
(1+G/j⍵C)1/2

=j⍵√LC(1+R/2j⍵L)(1+G/2j⍵L)
=j⍵√LC [1+R/2j⍵L+G/2j⍵C]
γ =j⍵√LC+ (R/2)(√C/L) + G√L/C
but we also know that γ=α+jβ
so we have α=(R/2)(√C/L) and β=j⍵√LC
and the phase velocity vp=⍵/β=2Π/(j⍵√LC)
so vp= 2Π/(j2Πf√LC
hence vp= 1/(jf√LC)
SMITH CHART
For evaluating the rectangular components, or the magnitude and phase of an input
impedance or admittance, voltage, current, and related transmission functions at all points
along a transmission line, including:
• Complex voltage and current reflections coefficients
• Complex voltage and current transmission coefficents
• Power reflection and transmission coefficients
• Reflection Loss
• Return Loss
• Standing Wave Loss Factor
• Maximum and minimum of voltage and current, and SWR
• Shape, position, and phase distribution along voltage and current standing waves
• Evaluating effects of shunt and series impedances on the impedance of a transmission line.
• For displaying and evaluating the input impedance characteristics of resonant and anti-
resonant stubs including the bandwidth and Q.
• Designing impedance matching networks using single or multiple open or shorted stubs.
• Designing impedance matching networks using quarter wave line sections.
• Designing impedance matching networks using lumped L-C components.
• For displaying complex impedances verses frequency.
• For displaying s-parameters of a network verses frequency.

 It is the most useful graphical tool for transmission line problems.
 From mathematical point of view, the Smith chart is simply a representation of all possible
complex impedances with respect to coordinates defined by the reflection coefficient.
 It can be used to convert from reflection coefficients to normalized impedances (or
admittances), and vice versa using the impedance (or admittance) circle printed on the chart.
When dealing with impedances on a Smith chart, normalized quantities are generally used
denoted by lowercase letters. The normalization constant is usually the characteristic
impedance of the line(z=Z/Z0)
 The domain of definition of the reflection coefficient is a circle of radius 1 in the complex
plane.
Fig-1: Smith Chart
 At point of Short, r = 0, x = 0 So zL= r+jx=0
 At point of Open, r = , x =  So zL= r+jx=
 If a lossless line of characteristics impedance Z0 is terminated with a load impedance ZL, the
reflection coefficient at the load can be written as
e
j
L
L
z
z 



1
1
Where Lz = ZL/ Z0 is the normalized impedance
Lz =
e
e
j
j




1
1
Writing Lz and  in terms of their real and imaginary parts as  = ir j and
Lz =rL+jxL then
Lz =rL+jxL=
ir
ir
j
j


1
1
Multiplying the numerator and denominator by the complex conjugate of the denominator
and rearranging gives
   rLr
r
i
L
L
r




1
1
1
2
2
2
     xL
i r
xL
1
1
1 222

The above two equation represents two families of a circle in the r , i plane.

Constant Resistance Circle : Center 






0,
1r
r
and Radius 





1
1
r
 Constant Reactance Circle : Center 





x
1
,1 and Radius 





x
1
Fig-2: Constant Resistance Circle Fig-3: Constant Reactance Circle
 Complete revolution on the smith chart is
2

on Transmission line. Distance between Vmax and
Vmin is
4

i.e 180.
 Movement from load towards generator is clockwise.

WAVEGUIDE
The transmission line can’t propagate high range of frequencies in GHz due to skin effect.
Waveguides are generally used to propagate microwave signal and they always operate
beyond certain frequency that is called “cut off frequency”. so they behaves as high pass
filter.
SKIN EFFECT :xc=
1
(2∗𝜋∗𝑓∗𝑐)
According to this relation,as frequency increases, xc tends to zero, that is short circuit. Hence
signal becomes grounded and can’t propagate further which is called skin effect.
Types of waveguides: - (1)rectangular waveguide (2)cylindrical waveguide (3)elliptical
waveguide (4)parallel waveguide
RECTANGULAR WAVEGUIDE :
Let us assume that the wave is travelling along z-axis and field variation along z-direction is
equal to e-Ƴz
,where z=direction of propagation and Ƴ= propagation constant.
Assume the waveguide is lossless (α=0) and walls are perfect conductor (σ=∞). According to
maxwell’s equation: ∇ × H=J+𝜕𝐷/𝜕𝑡 and ∇ × E = -𝜕𝐵/𝜕𝑡 .
So ∇ × H=J𝜔 ∈ 𝐸 − − − (1. 𝑎) , ∇ × E = −J𝜔𝜇𝐻. ---------(1.b)
Expanding equation (1),
|
𝐴𝑥 𝐴𝑦 𝐴𝑧
𝜕/𝜕𝑥 𝜕/𝜕𝑦 𝜕/𝜕𝑧
𝐻𝑥 𝐻𝑦 𝐻𝑧
|= J𝜔 ∈ [𝐸𝑥𝐴𝑥 + 𝐸𝑦𝐴𝑦 + 𝐸𝑧𝐴𝑧]
By equating coefficients of both sides we get,
𝜕
𝜕𝑦
𝐻𝑧 −
𝜕
𝜕𝑧
𝐻𝑦 =J𝜔 ∈Ex -----------------2(a)
−
𝜕
𝜕𝑥
𝐻𝑧 +
𝜕
𝜕𝑧
𝐻𝑥 = J𝜔 ∈ 𝐸𝑦 -----------2(b)

𝜕
𝜕𝑥
𝐻𝑦 −
𝜕
𝜕𝑦
𝐻𝑥 = J𝜔 ∈ 𝐸𝑧 -----------------2(c)
As the wave is travelling along z-direction and variation is along –Ƴz direction.
=>
𝜕
𝜕𝑧
(𝑒–Ƴz
)= -𝛾𝑒–Ƴz
.
Comparing above equations,
𝜕
𝜕𝑧
= −Ƴ .
So by putting this value of
𝜕
𝜕𝑧
in equations 2(a,b,c),we will get
𝜕
𝜕𝑦
𝐻𝑧 + Ƴ 𝐻𝑦 =j𝜔 ∈Ex -----------------3(a)
𝜕
𝜕𝑥
𝐻𝑧 + Ƴ 𝐻𝑥 = − j𝜔 ∈ 𝐸𝑦 -----------3(b)
𝜕
𝜕𝑥
𝐻𝑦 −
𝜕
𝜕𝑦
𝐻𝑥 = j𝜔 ∈ 𝐸𝑧 -----------------3(c)
Similarly from relation ∇ × E = −j𝜔𝜇𝐻 and
𝜕
𝜕𝑧
= −Ƴ ,we will get
𝜕
𝜕𝑦
𝐸𝑧 + Ƴ 𝐸𝑦 = - j𝜔𝜇Hx -----------------4(a)
𝜕
𝜕𝑥
𝐸𝑧 + Ƴ 𝐸𝑥 = j𝜔𝜇𝐻𝑦 -----------4(b)
𝜕
𝜕𝑥
𝐸𝑦 −
𝜕
𝜕𝑦
𝐸𝑥 = - j𝜔𝜇𝐻𝑧 -----------------4(c)
From equation sets of (3) , we will get :
𝜕
𝜕𝑦
𝐻𝑧 + Ƴ 𝐻𝑦 =j𝜔 ∈Ex
Ex=
1
j 𝜔∈
[
𝜕
𝜕𝑦
𝐻𝑧 + Ƴ 𝐻𝑦] ---------(5)
From equation sets of (4) ,we will get :
𝜕
𝜕𝑥
𝐸𝑧 + Ƴ 𝐸𝑥 = j𝜔𝜇𝐻𝑦
Ex=
1
Ƴ
[j𝜔𝜇𝐻𝑦 −
𝜕
𝜕𝑥
𝐸𝑧] ---------(6)
Equating equations (5) and (6), we will get
=>
1
j 𝜔∈
[
𝜕
𝜕𝑦
𝐻𝑧 + Ƴ 𝐻𝑦] =
1
Ƴ
[j𝜔𝜇𝐻𝑦 −
𝜕
𝜕𝑥
𝐸𝑧]
=>
Ƴ
j 𝜔∈
𝜕
𝜕𝑦
𝐻𝑧 +
Ƴ2
j 𝜔∈
Hy = j𝜔𝜇𝐻𝑦 −
𝜕
𝜕𝑥
𝐸𝑧
=> (
Ƴ2
j 𝜔∈
− j𝜔𝜇)Hy = −
𝜕
𝜕𝑥
𝐸𝑧 −
Ƴ
j 𝜔∈
𝜕
𝜕𝑦
𝐻𝑧

=> (
Ƴ2
+𝜔2 𝜇∈
𝑗𝜔 ∈
) Hy =−
𝜕
𝜕𝑥
𝐸𝑧 −
Ƴ
j 𝜔∈
𝜕
𝜕𝑦
𝐻𝑧
Let (Ƴ2
+ 𝜔2
𝜇 ∈) = 𝑕2
=> (
h2
𝑗𝜔 ∈
)Hy =−
𝜕
𝜕𝑥
𝐸𝑧 −
Ƴ
𝑗𝜔 ∈
𝜕
𝜕𝑦
𝐻𝑧
Hy = −
j𝜔∈
h2
𝜕
𝜕𝑥
𝐸𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑦
𝐻𝑧 ------------ (7)
Similarly we will get by simplifying other equations
Hx = −
j𝜔∈
h2
𝜕
𝜕𝑦
𝐸𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑥
𝐻𝑧 ------------ (8)
Ex = −
j𝜔𝜇
h2
𝜕
𝜕𝑦
𝐻𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑥
𝐸𝑧 ------------ (9)
Ey =
j𝜔𝜇
h2
𝜕
𝜕𝑥
𝐻𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑦
𝐸𝑧 ----------- (10)
IMPORTANT QUESTION :
(Q) Transverse electromagnetic mode(TEM mode)is not possible in a waveguide.why?
(A)Let the wave propagate along z-direction,then the waveguide field equation 7,8,9,10.as
wave propagate along z-direction Ez and Hz=0.From equations 7,8,9,10
:Ex,Hx,Ey,Hy=0.hence it is not possible practically.so Ez,Hz both can’t be zero.if
Ez=0,transverse electric mode exists and Hz=0,transverse magnetic mode exists.
Field solutions of rectangular waveguide :
∗To find the solution we have to assume waveguide is lossless that is 𝛼 = 0 and walls are
perfect conductor(𝜍 = ∞). According the Poisson’s equation ∇2
𝐸 = 𝛾2
𝐸 𝑎𝑛𝑑 ∇2
𝐻 = 𝛾2
𝐻
*As 𝛾 = 𝛼 + 𝑗𝛽 and as 𝛼 = 0 𝑠𝑜 the equations becomes 𝛾 = 𝑗𝛽 and 𝛾2
= −𝛽2
= −𝑘2
(let)

*now the Poisson’s equation are ∇2
𝐸+𝑘2
𝐸 = 0 − − − − − 𝑎
𝑎𝑛𝑑 ∇2
𝐻 + 𝑘2
𝐻 = 0 − − − −(𝑏)
Expanding equation (a)
𝜕2 𝐸𝑥
𝜕 𝑥2
+
𝜕2 𝐸𝑦
𝜕𝑦2
+
𝜕2 𝐸𝑧
𝜕𝑧2
+ 𝑘2
𝐸 = 0 − − − −(𝑐)
𝜕2 𝐸
𝜕 𝑥2
+
𝜕2 𝐸
𝜕𝑦2
+
𝜕2 𝐸
𝜕𝑧2
+ 𝑘2
𝐸 = 0 -----it is a second order partial differential equation whose
solution let it be E=XYZ where X=X(x),Y=Y(y),Z=Z(z)
Putting E in equation (b) we will get
𝜕2
(𝑋𝑌𝑍)
𝜕𝑥2
+
𝜕2
(𝑋𝑌𝑍)
𝜕𝑦2
+
𝜕2
(𝑋𝑌𝑍)
𝜕𝑧2
+ 𝑘2
(𝑋𝑌𝑍) = 0
=>𝑌𝑍
𝜕2 𝑋
𝜕𝑥2
+ 𝑋𝑍
𝜕2 𝑌
𝜕𝑦2
+ 𝑋𝑌
𝜕2 𝑍
𝜕𝑧2
+ 𝑘2
(𝑋𝑌𝑍) = 0
Dividing XYZ in both sides,We will get
1
𝑋
𝜕2
𝑋
𝜕𝑥2
+
1
𝑌
𝜕2
𝑌
𝜕𝑦2
+
1
𝑍
𝜕2
𝑍
𝜕𝑧2
+ 𝑘2
= 0
𝐾𝑥2
+𝑘𝑦2
+𝑘𝑧2
=𝑘 2
As
1
𝑋
𝜕2 𝑋
𝜕𝑥2
= −Kx2
,
1
𝑌
𝜕2 𝑌
𝜕𝑦2
= −Ky2
,
1
𝑍
𝜕2 𝑍
𝜕𝑧2
= -Kz2
------------(d)
As the wave is travelling along z-direction Z(z)=𝑒−𝛾𝑧
𝜕2 𝑍(𝑧)
𝜕𝑧2
=𝛾2
𝑒−𝛾𝑧

𝜕2 𝑍(𝑧)
𝜕𝑧2
=𝑍(𝑧) 𝛾2
by comparing it we will get 𝜕2
/𝜕𝑧2
=𝛾2

1
𝑍
𝜕2 𝑍
𝜕𝑧2
= -kz^2 =𝛾2
Similarly
1
𝑥
𝜕2 𝑋
𝜕𝑥2
+kx^2 =0

𝜕2 𝑋
𝜕𝑥2
+x kx^2 =0
It is a second order homogenous differential equation whose solution is
X(x)=C1cos 𝑘𝑥𝑥 +C2sin 𝑘xx ------(e)
X(x)=C3cos 𝑘𝑦𝑦 +C4sin 𝑘yy ------(f)

As E=XYZ ;
EXYZ = (C1cos 𝑘𝑥𝑥 +C2sin 𝑘xx)( C3cos 𝑘𝑦𝑦 +C4sin 𝑘yy )𝑒−𝛾𝑧
------(g)
Similarly by solving for magnetic field we will get
HXYZ = (B1cos 𝑘𝑥𝑥 +B2sin 𝑘xx)( B3cos 𝑘𝑦𝑦 +B4sin 𝑘yy ) 𝑒−𝛾𝑧
------(h)
Equations (g) and (h) are the field solutions foe rectangular waveguide.
CASE-1
FIELD SOLUTIONS FOR TRANSVERSE MAGNETIC FIELD IN RECTANGULAR
WAVEGUIDE :
Hz=0 and Ez≠ 0
EXYZ = (C1 cos 𝑘𝑥𝑥 +C2sin 𝑘xx)( C3cos 𝑘𝑦𝑦 +C4sin 𝑘yy ) 𝑒−𝛾𝑧
The values of C1,C2,C3,C4,Kx,Ky are found out from boundary equations.as we know that
the tangential component of E are constants across the boundary,then
E=
0, 𝑥 = 0 𝑎𝑛𝑑 𝑥 = 𝑎
0, 𝑦 = 0 𝑎𝑛𝑑 𝑦 = 𝑏
AT x=0 AND y=0 ;
E=C1C3 𝑒−𝛾𝑧
= 0 but we know that 𝑒−𝛾𝑧
≠ 0 wave is travelling along z-direction.
So either C1=0 or C3=0 oterwise C1C3=0
AT x=0 AND y=b ;
E= C1( C3cos 𝑘𝑦𝑏 +C4sin 𝑘yb ) 𝑒−𝛾𝑧
=0
So C1C3=0
So equation (g)becomes
EXYZ = (C2sin 𝑘xx × C4sin 𝑘yy )𝑒−𝛾𝑧
------(i)
Hence for x=0,E=0
So (C2sin 𝑘xa × C4sin 𝑘yy )𝑒−𝛾𝑧
= 0
=>sin 𝑘𝑥𝑎 = 0 => 𝑘x=
𝑚∗𝜋
𝑎
In equation (i) for y=b=>E=0;

So (C2sin 𝑘xx × C4sin 𝑘yb )𝑒−𝛾𝑧
= 0
=>sin 𝑘𝑦𝑏 = 0 => 𝑘y=
𝑛∗𝜋
𝑏
So finally solutions for TRANSVERSE MAGNETIC MODE is given by
Ez=C (sin(
𝑚∗𝜋
𝑎
)𝑥 × sin(
𝑛∗𝜋
𝑏
)y × 𝑒−𝛾𝑧
Where C2 × 𝐶4=C
CUT-OFF FREQUENCY :
It is the minimum frequency after which propagation occurs inside the waveguide.
As we know that => Kx^2 +ky^2+kz^2=k^2
=> Kx^2 +ky^2= k^2-kz^2
=> Kx^2 +ky^2=k^2+𝛾2
As we know that 𝛽 = −𝑗𝜔 𝜇𝜀 𝑎𝑛𝑑 𝑘2
= 𝛽2
So we will get that : => Kx^2 +ky^2=k^2+𝛾2
=𝜔2
𝜇𝜀 + 𝛾2
So 𝛾 =
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2
− 𝜔2 𝜇𝜀
At f=fc or w=wc ,at cut off frequency propagation is about to start. So 𝛾 = 0
=>0=
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2
− 𝜔𝑐2 𝜇𝜀
=>𝜔𝑐2
𝜇𝜀 =
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2
Wc=1/ 𝜇𝜀
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2
So fc=1/2𝜋 𝜇𝜀
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2
---------cut off frequency equation
where m=n=0,1,2,3……
At free space fc=1/2𝜋 𝜇𝑜𝜀𝑜
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2
=>fc=c/2
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2
---------cut off frequency equation in free space

CUT – OFF WAVELENGTH:
This is given by
ƴ𝑐 =
𝑐
𝑓
= 2 × (
1
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2)
DOMINANT MODE :
The mode having lowest cut-off frequency or highest cut-off wavelength is called
DOMINANT MODE.
*the mode can be TM01,TM10,TM11,But for TM10 and TM01,wave can’t exist.
*hence TM11has lowest cut-off frequency and is the DOMINANT MODE in case of all TM
modes only.
PHASE CONSTANT :
As we know that 𝛾 =
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2
− 𝜔2
𝜇𝜀
1/2
So j𝛽 = 𝜔2 𝜇𝜀 − 𝜔𝑐2 𝜇𝜀
This condition satisfies that only 𝜔𝑐2
𝜇𝜀 > 𝜔2
𝜇𝜀
So that 𝛽 = 𝜔2 𝜇𝜀 − 𝜔𝑐2 𝜇𝜀
PHASE VELOCITY :
It is given by Vp=𝜔/ 𝛽
Vp=
𝜔
(𝜔2 𝜇𝜀 −𝜔𝑐 2 𝜇𝜀 )
Vp=1/ [ 𝜔𝜀(1 − 𝑓𝑐2
/𝑓2
)]
GUIDE WAVELENGTH :
It is given by 𝜆𝑔 =
2𝜋
𝛽
=
2𝜋
𝜔2 𝜇𝜀 −𝜔𝑐 2 𝜇𝜀
𝜆𝑔 =1/ (𝑓2
𝜇𝜀 − 𝑓𝑐2
𝜇𝜀)
𝜆𝑔 =
𝑐
𝑓
/(1 − 𝑓𝑐2
/𝑓2
)
 𝜆𝑔 =
𝜆𝑜
[1−
𝜆𝑜
𝜆𝑐
2
]
1
2


1
𝜆𝑔2
=1/ 𝜆𝑜2
−
1
𝜆𝑐2
CASE -2
SOLUTIONS OF TRANSVERSE ELECTRIC MODE :
Here Ez=0 and Hz≠ 0
Hz=(B1cos 𝑘𝑥𝑥 +B2sin 𝑘xx)( B3cos 𝑘𝑦𝑦 +B4sin 𝑘yy ) 𝑒−𝛾𝑧
B1,B2,B3,B4,KX,KY are found from boundary conditions.
𝐸𝑥 = 0 𝑓𝑜𝑟 𝑦 = 0 𝑎𝑛𝑑 𝑦 = 𝑏
𝐸𝑦 = 0 𝑓𝑜𝑟 𝑥 = 0 𝑎𝑛𝑑 𝑥 = 𝑎
At x=0 and y=0 ;
Ey =
J𝜔𝜇
h2
𝜕
𝜕𝑥
𝐻𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑦
𝐸𝑧 ,as
Ƴ
𝑕2
𝜕
𝜕𝑦
𝐸𝑧 = 0
So Ey =
J𝜔𝜇
h2
𝜕
𝜕𝑥
𝐻𝑧
Here
𝜕
𝜕𝑥
𝐻𝑧 = [B1 ∗ kx ∗ (−sin 𝑘𝑥𝑥) + B2 ∗ kx ∗ cos 𝑘 xx)( B3 cos 𝑘𝑦𝑦 + B4 sin 𝑘 yy ) 𝑒−𝛾𝑧
]
So Ey =
J𝜔𝜇
h2
[B1 ∗ kx ∗ (−sin 𝑘𝑥𝑥) + B2 ∗ kx ∗ cos 𝑘 xx)( B3 cos 𝑘𝑦𝑦 + B4 sin 𝑘 yy ) 𝑒−𝛾𝑧
]
At x=0,
𝜕
𝜕𝑥
𝐻𝑧 = 0
0=[B2*Kx][(B3cosKyy+B4sinKyy)𝑒−𝛾𝑧
]
From this B2=0
So , Ex = −
j𝜔𝜇
h2
𝜕
𝜕𝑦
𝐻𝑧 −
Ƴ
𝑕2
𝜕
𝜕𝑥
𝐸𝑧 [as
Ƴ
𝑕2
𝜕
𝜕𝑥
𝐸𝑧 = 0];
Ex = −
j𝜔𝜇
h2
𝜕
𝜕𝑦
𝐻𝑧
Here
𝜕
𝜕𝑦
𝐻𝑧 = [B1 (cos 𝑘𝑥𝑥) + B2 sin 𝑘 xx)(− B3 ∗ ky ∗ sin 𝑘𝑦𝑦 + B4 ∗ ky ∗ cos 𝑘 yy ) 𝑒−𝛾𝑧
]
Ex = −
J𝜔𝜇
h2
[B1 (cos 𝑘𝑥𝑥) + B2 sin 𝑘 xx)(− B3 ∗ ky ∗ sin 𝑘𝑦𝑦 + B4 ∗ ky ∗ cos 𝑘 yy ) 𝑒−𝛾𝑧
]
B1 (cos 𝑘𝑥𝑥) + B2 sin 𝑘 xx)(− B3 ∗ ky ∗ sin 𝑘𝑦𝑦 + B4 ∗ ky ∗ cos 𝑘 yy ) 𝑒−𝛾𝑧
= 0

At y=0 ,
𝜕
𝜕𝑦
𝐻𝑧 = 0
B1 (cos 𝑘𝑥𝑥) + B2 sin 𝑘 xx B4 ∗ ky 𝑒−𝛾𝑧
= 0
From this B4=0
So Hz= B1 (cos 𝑘𝑥𝑥) ∗ B3 cos 𝑘𝑦𝑦 * 𝑒−𝛾𝑧
𝜕
𝜕𝑥
𝐻𝑧 = [B1 ∗ kx ∗ (−sin 𝑘𝑥𝑥) ( B3 cos 𝑘𝑦𝑦 ) 𝑒−𝛾𝑧
]
Here we know that at x=a,Ey=0
So Ey=
J𝜔𝜇
h2
[−B1 ∗ kx ∗ (−sin 𝑘𝑥𝑎) ∗ B3 cos 𝑘𝑦𝑦 ∗ 𝑒−𝛾𝑧
]=0
sin 𝑘𝑥𝑎 = 0 => 𝑘𝑥 =
𝑚𝜋
𝑎
At y=b,Ex=0
So Ex=−
J𝜔𝜇
h2
[B1 (cos 𝑘𝑥𝑥) (B3 ∗ ky ∗ sin 𝑘𝑦𝑏) 𝑒−𝛾𝑧
]=0
So here
sin 𝑘𝑦𝑏 = 0 => 𝑘𝑦 =
𝑛𝜋
𝑏
So the general TRANSVERSE ELECTRIC MODE solution is given by
Hz=B (cos
𝑚𝜋
𝑎
𝑥) (cos
𝑛𝜋
𝑏
𝑦) 𝑒−𝛾𝑧
Where B=B1B3
CUT-OFF FREQUENCY :
The cut-off frequency is given as
 fc=c/2
𝑚𝜋
𝑎
2
+
𝑛𝜋
𝑏
2 1/2
---------cut off frequency equation in free space
DOMINANT MODE :
The mode having lowest cut-off frequency or highest cut-off wavelength is called
DOMINANT MODE.here TE00 where wave can’t exist.
So fc(TE01)=c/2b
fc(TE10)=c/2a
for rectangular waveguide we know that a>b

so TE10 is the dominant mode in all rectangular waveguide.
DEGENERATE MODE :
The modes having same cut-off frequency but different field equations are called degenerate
modes.
WAVE IMPEDANCE :
Impedance offered by waveguide either in TE mode or TM mode when wave travels through
,it is called wave impedance.
For TE mode
ƞ𝑇𝐸 =
ƞ𝑖
(1 −
𝑓𝑐2
𝑓2 )
And
ƞ𝑇𝑀 = ƞ𝑖 ∗ (1 −
𝑓𝑐2
𝑓2
)
Where ƞ𝑖 = intrinsic impedance = 377ohm = 120π

CYLINDRICAL WAVEGUIDES
A circular waveguide is a tubular, circular conductor. A plane wave propagating through a
circular waveguide results in transverse electric (TE) or transverse magnetic field(TM)
mode.
Assume the medium is lossless(α=0) and the walls of the waveguide is perfect
conductor(σ=∞).
The field equations from MAXWELL’S EQUATIONS are:-
∇xE=-jωμH ------(1.a)
∇xH=jωϵE -----(1.b)
Taking the first equation,
∇xE=-jωμH
Expanding both sides of the above equation in terms of cylindrical coordinates, we get
1
𝜌
*|
𝐴𝜌 𝜌𝐴𝜑 𝐴𝑧
𝜕/𝜕𝜌 𝜕/𝜕𝜑 𝜕/𝜕𝑧
𝐸𝜌 𝜌𝐸𝜑 𝐸𝑧
| =-j𝜔𝜇[𝐻𝜌𝐴𝜌 + 𝐻𝜑𝐴𝜑 + 𝐻𝑧𝐴𝑧]
Equating :-
1
𝜌
𝜕 𝐸𝑧
𝜕𝜑
−
𝜕(𝜌𝐸𝜑 )
𝜕𝑧
=-jωμH𝜌 ------ (2.a)
𝜕 𝐸𝜌
𝜕𝑧
−
𝜕(𝐸𝑧)
𝜕𝜌
=-jωμH𝜑 ------ (2.b)
1
𝜌
𝜕 𝜌𝐸𝜑
𝜕𝜌
−
𝜕(𝐸𝜌)
𝜕𝜑
=-jωμH𝑧 ------- (2.c)
Similarly expanding ∇xH=jωϵE,
1
𝜌
*|
𝐴𝜌 𝜌𝐴𝜑 𝐴𝑧
𝜕/𝜕𝜌 𝜕/𝜕𝜑 𝜕/𝜕𝑧
𝐻𝜌 𝜌𝐻𝜑 𝐻𝑧
| =j𝜔𝜖[𝐸𝜌𝐴𝜌 + 𝐸𝜑𝐴𝜑 + 𝐸𝑧𝐴𝑧]
Equating:
1
𝜌
𝜕 𝐻𝑧
𝜕𝜑
−
𝜕(𝜌𝐻𝜑 )
𝜕𝑧
= jωϵE𝜌 ------ (3.a)
𝜕 𝐻𝜌
𝜕𝑧
−
𝜕(𝐻𝑧)
𝜕𝜌
=-jωϵE𝜑 ------- (3.b)
1
𝜌
𝜕 𝜌𝐻𝜑
𝜕𝜌
−
𝜕(𝐻𝜌)
𝜕𝜑
=jωϵE𝑧 ------- (3.c)

Let us assume that the wave is propagating along z direction. So,
Hz=𝑒−𝛾𝑧
;
=>
𝜕𝐻𝑧
𝜕𝑧
= −𝛾𝑒−𝛾𝑧
𝜕
𝜕𝑧
= −𝛾
Putting in equation 2 and 3:
𝜕 𝐸𝑧
𝜕𝜑
+ 𝛾𝜌𝐸𝜑 =-jωμ𝜌H𝜌 ------ (4.a)
𝛾𝐸𝜌 +
𝜕(𝐸𝑧)
𝜕𝜌
=jωμ𝜌H𝜑 ------- (4.b)
𝜕 𝜌𝐸𝜑
𝜕𝜌
−
𝜕(𝐸𝜌)
𝜕𝜑
=-jωμ𝜌H𝑧 ------- (4.c)
And
1
𝜌
𝜕 𝐻𝑧
𝜕𝜑
+ 𝛾𝜌𝐻𝜑 =jωϵE𝜌 ------ (5.a)
𝛾𝐻𝜌 +
𝜕(𝐻𝑧)
𝜕𝜌
=jωϵE𝜑 ------- (5.b)
1
𝜌
𝜕 𝜌𝐻𝜑
𝜕𝜌
−
𝜕(𝐻𝜌)
𝜕𝜑
=jωϵE𝑧 ------- (5.c)
Now from eq(4.a) and eq(5.b),we get
H𝜌 =
1
−jωμ𝜌
𝜕 𝐸𝑧
𝜕𝜑
+ 𝛾𝜌𝐸𝜑 ; H𝜌=
1
𝛾
[-jωϵE𝜑-
𝜕(𝐻𝑧)
𝜕𝜌
]
∴
1
−jωμ𝜌
𝜕 𝐸𝑧
𝜕𝜑
+ 𝛾𝜌𝐸𝜑 =
1
𝛾
[-jωϵE𝜑-
𝜕(𝐻𝑧)
𝜕𝜌
]
=>
1
𝜌
𝜕 𝐸𝑧
𝜕𝜑
+ 𝛾𝐸𝜑= -
𝜔2 𝜇𝜀
𝛾
E𝜑 +
jωμ
γ
∂Hz
∂ρ
=> (
γ2+𝜔2 𝜇𝜀
γ
)Eφ =
jωμ
γ
∂Hz
∂ρ
-
1
ρ
∂Hz
∂ρ
Let (γ2
+ 𝜔2
𝜇𝜀) =h2
=Kc2
;
For lossless medium α=0;γ=jβ;
Now the final equation for Eφ is

Eφ =
−j
Kc2
(
β
ρ
∂Ez
∂φ
− ωμ
∂Hz
∂ρ
) ----- (6.a)
Hφ =
−j
Kc2
(ωε
∂Ez
∂ρ
+
β
ρ
∂Hz
∂φ
) ----- (6.b)
Eρ =
−j
Kc2
(
ωμ
ρ
∂Hz
∂φ
+ β
∂Ez
∂ρ
) ----- (6.c)
Hρ=
j
Kc2
(
ωε
ρ
∂Ez
∂φ
− β
∂Hz
∂ρ
) ------ (6.d)
Equations (6.a),(6.b),(6.c),(6.d) are the field equations for cylindrical waveguides.
TE MODE IN CYLINDRICAL WAVEGUIDE :-
For TE mode, Ez=0, Hz≠0.
As the wave travels along z-direction,e−γz
is the solution along z-direction.
As, γ2
+ 𝜔2
𝜇𝜀 =h2
;
 -β2
+ω2
μϵ =Kc2
;
 -β2
+K2
=Kc2
(as K2
= 𝜔2
𝜇𝜀)
According to maxwell’s equation, the laplacian of Hz :
∇2
Hz=−𝜔2
𝜇𝜀Hz;
 ∇2
Hz+𝜔2
𝜇𝜀Hz=0;
 ∇2
Hz+𝐾2
Hz=0
Expanding the above equation, we get:
∂2Hz
∂ρ2 +
1
ρ
∂Hz
∂ρ
+
1
𝜌2
∂2HZ
∂φ2 +
∂2Hz
∂z2
+K2
Hz =0;
Now, HZ= e−γz
;
∂2Hz
∂z2
=(−γ)2
e−γz
;
∂2Hz
∂z2
=−β2
e−γz
;
∂2Hz
∂z2
=−β2
Hz =>
∂2
∂z2
=−β2
;
Putting this value in the above equations, we get:-
∂2Hz
∂ρ2 +
1
ρ
∂Hz
∂ρ
+
1
𝜌2
∂2HZ
∂φ2 −β2
Hz+K2
Hz =0;
∂2Hz
∂ρ2 +
1
ρ
∂Hz
∂ρ
+
1
𝜌2
∂2HZ
∂φ2 +Kc2
Hz =0; [as -β2
+K2
=Kc2
]

∂2Hz
∂ρ2 +
1
ρ
∂Hz
∂ρ
+Kc2
Hz = -
1
𝜌2
∂2HZ
∂φ2 ;
The partial differential with respect to ρ and φ in the above equation are equal only when
the individuals are constant (Let it be Ko
2
).

-
1
𝜌2
∂2HZ
∂φ2 = Ko
2
 ∂2HZ
∂φ2 +𝜌2
Ko
2
=0
Solutions to the above differential equation is:-
Hz = B1sin (Koφ)+B2cos(Koφ)-----{solution along φ direction}.
Now,
∂2Hz
∂ρ2 +
1
ρ
∂Hz
∂ρ
+(Kc2
Hz - Ko
2
)= 0
This equation is similar to BESSEL’S EQUATION,so the solution of this equation is
Hz=CnJn(Kc ρ) --------{solution along 𝜌-direction}
Hence,
Hz=Hz(ρ)Hz(φ)e−γz
;
So, the final solution is,
Hz= CnJn(Kc ρ)[ B1sin (Koφ)+B2cos(Koφ)] e−γz
Applying boundary conditions:-
At ρ=a, Eφ=0 =>
∂Hz
∂ρ
=0,
=> Jn (Kc ρ) =0
=> Jn(Kc a) =0
If the roots of above equation are defined as Pmn’,then
Kc=
Pmn ’
a
;
∴
CUT-OFF FREQUENCY :- It is the minimum frequency after which the propagation
occurs inside the cavity.
∴ γ=0;
Hz= CnJn (
Pmn ’
a
ρ) [ B1sin (Koφ)+B2cos(Koφ)] e−γz

But we know that γ2
+ 𝜔2
𝜇𝜀 =Kc2
;
 𝜔2
𝜇𝜀 =Kc2
 𝜔2
=
Kc2
𝜇𝜀
 2πfc=
Kc2
𝜇𝜀
 fc=
1
2π
Kc2
𝜇𝜀
∴ fc=
Pmn ′
2πa 𝜇𝜀
CUTOFF WAVELENGTH :-
c
fc
=
1
𝜇𝜀
Pmn ′
2πa 𝜇𝜀
=
2πa
Pmn ’
The experimental values of Pmn’ are:-
As seen from this table,TE11 mode has the lowest cut off frequency, hence TE11 is the
dominating mode.
TM MODE IN CYLINDRICAL WAVEGUIDE :-
For TM mode Hz=0,Ez≠0.
From the calculation in TE mode, we got the equation as,
∂2Ez
∂ρ2 +
1
ρ
∂Ez
∂ρ
+
1
𝜌2
∂2Ez
∂φ2 +Kc2
Ez =0; -------(2)
 ∂2Ez
∂φ2 +𝜌2
K1
2
=0 (let k1 be a constant)
n m 1 2 3
0 3.832 7.016 10.173
1 1.841 5.331 8.536
2 3.054 6.706 9.969
3 3.054 6.706 9.970
WAVE IMPEDANCE(ZTE) =
ηk
β

So, the general solution of the above equation is
Ez=C1sin(k1φ)+C2cos(k1φ)
Applying the boundary value conditions,i.e at ρ=a,Ez=0.
We get Jn(Kc a)=0;
So,if Pmn is the root of the above equation, then
Kc=
Pmn
a
The experimental values of Pmn’ are:-
n m 1 2 3
0 2.405 5.520 8.654
1 3.832 7.016 10.174
2 5.135 8.417 11.620
So, we can conclude that the TE01 having a value of 2.405 is the lowest one. But since
this value is greater than the TE11 mode, so mode TE11 is the dominant mode for the
cylindrical TM modes. Here m≥1,so there is no TM10 mode.
CUTOFF FREQUENCY:
The cut off frequency is given by
fc=
Pmn
2πa 𝜇𝜀
CUTOFF WAVELENGTH:-
The cut off wavelength is given by
c
fc
=
1
𝜇𝜀
Pmn
2πa 𝜇𝜀
=
2πa
Pmn
WAVE IMPEDANCE :-
The wave impedance is given by
ηk
β
.

MICROWAVE COMPONENTS
MICROWAVE RESONATOR:
 They are used in many applications such as oscillators, filters, frequency meters, tuned
amplifiers and the like.
 A microwave resonator is a metallic enclosure that confines electromagnetic energy
and stores it inside a cavity that determines its equivalent capacitance and inductance
and from the energy dissipated due to finite conductive walls we can determine the
equivalent resistance.
 The resonator has finite number of resonating modes and each mode corresponds to a
particular resonant frequency.
 When the frequency of input signal equals to the resonant frequency, maximum
amplitude of standing wave occurs and the peak energy stored in the electric and
magnetic field are calculated.
RECTANGULAR WAVEGUIDE CAVITY RESONATOR:
 Resonator can be constructed from closed section of waveguide by shorting both ends
thus forming a closed box or cavity which store the electromagnetic energy and the
power can be dissipated in the metallic walls as well as the dielectric medium
DIAGRAM:
 The geometry of rectangular cavity resonator spreads as
0≤x≤a;
0≤y≤b;
0≤z≤d
 Hence the expression for cut-off frequency will be

ω0
2
µ € = (mπ/a)2
+ ( nπ/b)2
+ (lπ/d)2
or ω0 =
𝟏
µ€
[(mπ/a)2
+ ( nπ/b)2
+ (lπ/d)2
]1/2
or f0 =
𝟏
𝟐𝝅 µ€
[(mπ/a)2
+ ( nπ/b)2
+ (lπ/d)2
]1/2
or f0=
𝒄′
𝟐
[(mπ/a)2
+ ( nπ/b)2
+ (lπ/d)2
]1/2
 This is the expression for resonant frequency of cavity resonator.
 The mode having lowest resonant frequency is called DOMINANT MODE and for TE
AND TM the dominant modes are TE-101 and TM-110 respectively.
QUALITY FACTOR OF CAVITY RESONATOR:
 Q=2π x
maximum energy stored per cycle
energy dissipated per cycle
FACTORS AFFECTING THE QUALITY FACTOR:
Quality factor depends upon 2 factors:
 Lossy conducting walls
 Lossy dielectric medium of a waveguide
1) LOSSY CONDUCTING WALL:
 The Q-factor of a cavity with lossy conducting walls but lossless dielectric medium
i.e. σc ≠ ∞ and σ =0
Then Qc = (2ω0 We/Pc)
Where w0-resonant frequency
We-stored electrical energy
Pc-power loss in conducting walls
 From dimensional point of view:
Qc = (kad3
) (bŋ) x { 1/(2l2
a3
d + l3
a3
d + ad3
+ 2bd3
) } /( 2π2
Rs)
Where k = (ω2
µ€) 1/2
ŋ = ŋi/ 𝝐r = 377/ 𝝐r
2) LOSSY DIELECTRIC MEDIUM:
The Q-factor of a cavity with lossy dielectric medium but lossless conducting walls
i.e. σc=∞ and σ≠0

Qd = 2ω0We/ Pd = (1/ tan 𝜹)
Where tan 𝛿 =
𝜍
𝜔𝜖
Pd=power loss in dielectric medium
 When both the conducting walls and the dielectric medium are lossy in nature then
Total power loss = Pc+Pd
1/Qtotal = 1/Qc +1/Qd
or Qtotal = 1/ (1/Qc +1/Qd)
POWER DIVIDERS:
 Power dividers and combiners are the passive microwave components that are used for
power division and combination in microwave frequency range
 In this case, the input power is divided into two or more signals of lesser power.
 The power divider has certain basic parameters like isolation, coupling factor and
directivity.
T-JUNCTION POWER DIVIDER USING WAVEGUIDE:
The T-junction power divider is a 3-port network that can be constructed either from a
transmission line or from the waveguide depending upon the frequency of operation.
For very high frequency, power divider using waveguide is of 4 types
 E-Plane Tee
 H-Plane Tee
 E-H Plane Tee/Magic Tee
 Rat Race Tee

E-PLANE TEE:
Diagram
 It can be constructed by making a rectangular slot along the wide dimension of the
main waveguide and inserting another auxiliary waveguide along the direction so that
it becomes a 3-port network.
 Port-1 and Port-2 are called collinear ports and Port-3 is called the E-arm.
 E-arm is parallel to the electric field of the main waveguide.
 If the wave is entering into the junction from E-arm it splits or gets divided into Port-1
and Port-2 with equal magnitude but opposite in phase
 If the wave is entering through Port-1 and Port-2 then the resulting field through Port-
3 is proportional to the difference between the instantaneous field from Port-1 and
Port-2
H-PLANE TEE:
Diagram:
 An H-plane tee is formed by making a rectangular slot along the width of the main
waveguide and inserting an auxiliary waveguide along this direction.
 In this case, the axis of the H-arm is parallel to the plane of the main waveguide.
 The wave entering through H-arm splits up through Port-1 and Port-2 with equal
magnitude and same phase
 If the wave enters through Port-1 and Port-2 then the power through Port-3 is the
phasor sum of those at Port-1 and Port-2.
 E-Plane tee is called PHASE DELAY and H-Plane tee is called PHASE ADVANCE.

E-H PLANE TEE/MAGIC TEE:
Diagram:
 It is a combination of E-Plane tee and H-Plane tee.
 If two waves of equal magnitude and the same phase are fed into Port-1 and Port-2,
the output will be zero at Port-3 and additive at Port-4.
 If a wave is fed into Port-4 (H-arm) then it will be divided equally between Port-1 and
Port-2 of collinear arms (same in phase) and will not appear at Port-3 or E-arm.
 If a wave is fed in Port-3 then it will produce an output of equal magnitude and
opposite phase at Port-1 and Port-2 and the output at Port-4 will be zero.
 If a wave is fed in any one of the collinear arms at Port-1 or Port-2, it will not appear
in the other collinear arm because the E-arm causes a phase delay and the H-arm
causes phase advance.
T-JUNCTION POWER DIVIDER USING TRANSMISSION LINE:
Diagram:
 It is a junction of 3 transmission lines

 In this case, if P1 is the input port power then P2 and P3 are the power of output Port-
2 and Port-3 respectively.
 To transfer maximum power from port-1 to port-2 and port-3 the impedance must
match at the junction.
 For maximum power transfer
Z01= Z02 || Z03
 1/Z01= 1/Z02 + 1/Z03 (Condition for lossless power division)
DIRECTIONAL COUPLER:
Diagram:
 It is a 4- port waveguide junction consisting of a primary waveguide 1-2 and a
secondary waveguide 3-4.
 When all the ports are terminated in their characteristic impedance there is free
transmission of power without reflection between port-1 and port-2 and no power
transmission takes place between port-1 and port-3 or port-2 and port-4 a sno coupling
exists.
 The characteristic of a directional coupler is expressed in terms of its coupling factor
and directivity.
 The coupling factor is the measure of ratio of power levels in primary and secondary
lines.
 Directivity is the measure of how well the forward travelling wave in the primary
waveguide couples only to a specific port of the secondary waveguide.
 In ideal case, directivity is infinite i.e. power at port-3 =0 because port-2 and port-4
are perfectly matched.
 Let wave propagates from port-1 to port-2 in primary line then:

Coupling factor (dB) =10 log10 (P1/P4)
Directivity (dB) = 10 log10 (P4/P3)
Where P1=power input to port-1
P3=power output from port-3 and P4=power output from port-4
CIRCULATORS AND ISOLATORS:
 Both microwave circulators and microwave isolators are non-reciprocal transmission
devices that use Faraday rotation in the ferrite material.
CIRCULATOR:
 A microwave circulator is a multiport waveguide junction in which the wave can flow
only in one direction i.e. from the nth port to the (n+1)th port.
 It has no restriction on the number of ports
 4-port microwave circulator is most common.
 One of its types is a combination of two 3-dB side hole directional couplers and a
rectangular waveguide with two non reciprocal phase shifters.
Diagram:
 Each of the two 3db couplers introduce phase shift of 90 degrees
 Each of the two phase shifters produce a fixed phase change in a certain direction.
 Wave incident to port-1 splits into 2 components by coupler-1.
 The wave in primary guide arrives at port-2 with 180 degrees phase shift.
 The second wave propagates through two couplers and secondary guide and arrives at
port-2 with a relative phase shift of 180 degrees.
 But at port-4 the wave travelling through primary guide phase shifter and coupler-2
arrives with 270 degrees phase change.
 Wave from coupler-1 and secondary guide arrives at port-4 with phase shift of 90
degrees.

 Power transmission from port-1 to port-4 =0 as the two waves reaching at port-4 are
out of phase by 180 degrees.
w1-w3 = (2m+1) π rad/s
w2-w4 = 2nπ rad/s
Power flow sequence: 1-> 2 -> 3 -> 4-> 1
MICROWAVE ISOLATOR:
 A non reciprocal transmission device used to isolate one component from reflections
of other components in the transmission line.
 Ideally complete absorption of power takes place in one direction and lossless
transmission is provided in the opposite direction
 Also called UNILINE, it is used to improve the frequency stability of microwave
generators like klystrons and magnetrons in which reflections from the load affects the
generated frequency.
 It can be made by terminating ports 3 and 4 of a 4-port circulator with matched loads.
 Additionally it can be made by inserting a ferrite rod along the axis of a rectangular
waveguide.

REFLEX KLYSTRON
The reflex klystron is a single cavity variable frequency time-base generator of low power
and load effiency
APPLICATION:
 It is widely used as in radar receiver
 Local oscillators in microwave receiver
 Portable microwave rings
 Pump oscillator in parametric amplifier
CONSTRUCTION:
 Reflex cavity klystron consists of an electron gun , filament surrounded by
cathode and a floating electron at cathode potential
 Electron gun emits electron with constant velocity
1
2
m𝑣2
=qVa
V=
2𝑞𝑉𝑎
𝑚
m/s
OPERATION:
 The electron that are emitted from cathode with constant velocity enter the cavity
where the velocity of electrons is changed or modified depending upon the cavity
voltage.
 The oscillations is started by the device due to high quality factor and to make it
sustained we have to apply the feedback.
Hence there are the electrons which will bunch together to deliver the energy act a
time to the RF signal.
 Inside the cavity velocity modulation takes place. Velocity modulation is the
process in which the velocity of the emitted electrons are modified or change
with respect to cavity voltage. The exit velocity or velocity of the electrons
after the cavity is given as
V’=
2𝑞(𝑉𝑎+𝑉𝑖 sin 𝜔𝑡 )
𝑚
 In the cavity gap the electrons beams get velocity modulated and get bunched to
the drift space existing between cavity and repellar.
 Bunching is a process by which the electrons take the energy from the cavity at
a different time and deliver to the cavity at the same time.

Diagram:
Bunching continuously takes place for every negative going half cycle and the
most appropriate time for the electrons to return back to the cavity ,when the cavity
has positive peak .So that it can give maximum retardation force to electron.
 It is found that when the electrons return to the cavity in the second positive
peak that is 1 whole ¾ cycle.(n=1π).It is obtained max power and hence it is
called dominant mode.
The electrons are emitted from cathode with constant anode voltage Va, hence the initial
entrance velocity of electrons is
V=
2𝑞𝑉𝑎
𝑚
m/s
Inside the cavity the velocity is modulated by the cavity voltage Visin(𝜔t) as,
V=
2𝑞(𝑉𝑎+𝑉𝑖 sin 𝜔𝑡 )
𝑚
V=
2𝑞𝑉𝑎
𝑚
+
2𝑞𝑉𝑎𝐾𝑎𝑉𝑖 sin 𝜔𝑡
𝑉𝑎𝑚
V= 𝑉𝑜2 +
𝑉𝑜2 𝐾𝑖𝑉𝑖 sin 𝜔𝑡
𝑉𝑎

V= Vo 1 +
𝐾𝑖𝑉𝑖 sin 𝜔𝑡
𝑉𝑎
V= 1 +
𝑉𝑜2 𝑖𝑉𝑖 sin 𝜔𝑡
𝑉𝑎
When,
𝑘𝑖𝑣𝑖
𝑉𝑎
=Depth of velocity
V=Vo ( 1 +
𝑉𝑜2 𝑖𝑉𝑖 sin 𝜔𝑡
2𝑉𝑎
)
TRANSIENT TIME:
Transit time is defined as the time spent by the electrons in the cavity space or, time taken by
the electrons to leave the cavity and again return to the cavity.
(FIGURE)
If 𝑡1 is the time at which electrons leave the cavity and 𝑡2 is the time at which electrons
bunch in the cavity then, transit time
𝑡𝑟= 𝑡1 − 𝑡2
During this time the net displacement by electrons is zero. That the potential of two point A
and B is VA and VB(plate) as known in figure,then,
𝑉𝐴𝐵 = 𝑉𝐴 − 𝑉𝐵
= 𝑉𝐴 + 𝑉𝑖 sin 𝑤𝑡 + 𝑉𝑅

=𝑉𝐴 + 𝑉𝑅 + 𝑉𝑖 sin 𝑤𝑡
Neglecting the AC compoment,
𝑉𝐴𝐵 = 𝑉𝑎 + 𝑉𝑅
E =
𝜕𝑉 𝐴𝐵
𝜕𝑥
=
−𝑉 𝐴𝐵
𝑆
=
−(𝑉𝑎+ 𝑉𝑅 )
𝑆
-------(a)
The force experienced on an electron
F=qe=
−𝑞(𝑉𝑎+ 𝑉𝑅)
𝑆
F=
m ∂2x
∂t2
-------(b)
From equations a and b we get
m ∂2x
∂t2
=
𝑆
Integrating both sides we get,
m ∂2x
∂t2
=
𝑆
m ∂x2
=
𝑆
𝑡
𝑡1
𝜕𝑡
m
𝜕𝑥
𝜕𝑡
=
𝑆
𝑡𝑡1
𝑡
𝜕𝑥
𝜕𝑡
=
𝑚𝑆
(t-𝑡1)+ 𝑘1
∴ 𝑘1is called velocity constant and assumed to velocity at (t-𝑡1)
𝜕𝑥
𝜕𝑡
=
𝑚𝑆
(t-𝑡1)+𝑉 𝑡1
𝜕𝑥 =
𝑚𝑆
(t − 𝑡1) ∂ 𝑡 + 𝑉 𝑡1
X=
−𝑞(𝑉𝑎+ 𝑉𝑅 )
𝑚𝑆
[𝑡2
2𝑡1
𝑡
] − 𝑡1 [𝑡]𝑡1
𝑡
+ 𝑉 𝑡1 𝜕𝑡
=
𝑚𝑆
[
𝑡2−𝑡12
2
− 𝑡2 − 𝑡2 𝑡1] + 𝑉 𝑡1 𝜕𝑡
=
𝑚𝑆
𝑡2−𝑡12−2𝑡2 𝑡1+2𝑡2
2
2
+ 𝑉 𝑡1 𝜕𝑡

=
𝑚𝑆
𝑡2+𝑡12−2𝑡2 𝑡1
2
+ 𝑉 𝑡1 𝜕𝑡
=
𝑚𝑆
(𝑡−𝑡1)2
2
+ 𝑉 𝑡1 𝜕𝑡
=
𝑚𝑆
(𝑡−𝑡1)2
2
+ 𝑉 𝑡1 𝑡 − 𝑡1 + 𝑘2
Where,k2 is displacement constant at t=t2,x=0 .In practice k2=the cavity width which is
negligible with respect to cavity space s.Here we can neglect k2 in the expression of x
At t=t2,x=0
0=
−𝑞(𝑉𝑎+ 𝑉𝑅 )
𝑚𝑆
(𝑡−𝑡1)2
2
+𝑉 𝑡1 𝑡 − 𝑡1

𝑚𝑆
(𝑡2−𝑡1)2
2
= 𝑉 𝑡1 𝑡2 − 𝑡1
 𝑡2 − 𝑡1 =
2𝑉 𝑡1 𝑚𝑠
𝑞(𝑉𝑎+ 𝑉𝑅 )
TRANSIT ANGLE:
𝜔𝑡𝑟 = 𝜔 𝑡2 − 𝑡1 = 𝜔
𝑞 𝑉𝑎+ 𝑉𝑅
𝜔𝑡𝑟 = 𝜔
We know,
n=+3/4, for n=0,1,2,3,4…..
n-1/4. for n=0,1,2,3,4…..
2× 𝜋 𝑡2 − 𝑡1 = 𝑛 −
1
4
2𝜋 ×T
2× 𝜋 × 𝑓 𝑡2 − 𝑡1 = 2𝑛𝜋 −
𝜋
2
𝜔𝑡𝑟 = 2𝑛𝜋 −
𝜋
2
= 𝜔
OUTPUT POWER:
The beam current of Reflex klystron is given as
Ib=IO+ 2I0In x′
cos(nωt − φ
∞
𝑛=1
I0is dc current due to cavity voltage is given by
Pdc=vaIo -------(1)

The ac component of the current is given by
Iac= 2I0In x′
cos(nωt − φ
∞
𝑛=1
For (n=1),we have fundamental current component ie,
If 2I0I1 x′
cos(nωt − φ
For n=2; cos(nωt − φ) = 1
I2=2IoKiJi(Xi)
Power=
viI2
2
=
vi
2
(2IokiJi Xi )
𝜔 𝑡2 − 𝑡1 = 𝜔
𝜔𝑡2= 𝜔𝑡1+
2𝑉0 𝑚𝑠𝜔
[1 +
𝑘 𝑖 𝑣 𝑖
2𝑣 𝑎
sin 𝜔𝑡1]
∴ [
2𝑉0 𝑚𝑠𝜔
] = 𝛼
 𝜔𝑡2= 𝜔𝑡1+𝛼[1 +
𝑘 𝑖 𝑣 𝑖
2𝑣 𝑎
sin 𝜔𝑡1]
 𝜔𝑡2= 𝜔𝑡1+𝛼 +
𝑘 𝑖 𝑣 𝑖 𝛼
2𝑣 𝑎
sin 𝜔𝑡1]
Where ,
𝑘 𝑖 𝑣 𝑖 𝛼
2𝑣 𝑎
=x, bunching parameter
Vi=
2va x
αki
=
2va x
(2nπ−
π
2
)ki
Po/p=
2va xI0×Ji x
(2nπ−
π
2
)
Efficiency: η% =
Poutput
Pinput
× 100%
=
2va xI0×Ji x
(2nπ−
π
2
)va xI0
=
2×Ji x
(2nπ−
π
2
)
× 100%
Electronics admittance of reflex klystron
It is defined as the ratio of current induced in the cavity by the modulation of electron beam
to the voltage across the cavity gap.

Ye=
I2
v2
,
 I2=2IokiJi(x’)cos(𝜔𝑡 − 𝜑)
 =2IokiJi 𝑒−𝑗𝜑
 V2=V1 𝑒−𝜋/2
=
2 vax ′
αki
𝑒−𝑗𝜋 /2
 Ye=
αIo𝑘𝑖2
va
Ji(x)′ sin φ
x′
+𝑗
αIo𝑘𝑖2
va
Ji(x)′ cos φ
x′
Ye=Ge + jβe

MAGNETRON
DIFFERENCE BETWEEN REFLEX KLYSTRON AND MAGNETRON:
REFLEX KLYSTRON MAGNETRON
 It is a linear tube in which the
magnetic field is applied to focus
the electron and electric field is
applied to drift the electron.
 In klystron the bunching takes
places only inside the cavity
which is very small ,hence
generate low power and low
frequency.
 In magnetron the magnetic field
and electric field are
perpendicular to each other hence
it is called as cross field device.
 In magnetron the interacting or
bunching space is extended so the
efficiency can be increase.
APPLICATION:
 Used as oscillator.
 Used in radar communication.
 Used in missiles.
 Used in microwave oven (in the range of frequency of 2.5Ghz).
Types of magnetron:
Magnetron is of 3 types:
 Negative resistance type.
 Cyclotron frequency type.
 Cavity type.
Construction of cavity magnetron:
Cavity type magnetron depends upon the interaction of electron with a rotating magnetic
field with constant angular velocity.
FIGURE:

A magnetron consists of a cathode which is used to emit electrons and a number of anode
cavities a permanent magnet is placed on the backside of cathode. The space between anode
cavity and cathode is called interacting space. The electron which are emitted from cathode
moves in different path in the interacting space depending upon the strength of electron and
magnetic field applied to the magnetron.
OPERATION:
EFFECT OF ELECTRIC FIELD ONLY:
 In the absence of magnetic field(B=0) the electron travel straight from the cathode to
the anode due to the radial electric field force acting on it(indicated by path A).
 If the magnetic field strength increases slightly it will exert a lateral force which bends
the path of the as indicated in path B.
 The radius of the path is given as
r=
𝑚𝑣
𝑒𝐵
where v=velocity of electron
B=magnetic field strength
 If from reaching the anode current become zero(indicated by path D).the strength of
magnetic field is made sufficiently high enough, so to prevent the electron
 The magnetic field required to return the electron back to the cathode just touching the
surface of anode is called critical magnetic field or cut off magnetic field(Bc).
 If B>Bc the electron experiences a grater rotational force and may return back to the
cathode quite faster this results is heating of cathode.
Effect of magnetic field:
The force experience by the electron because of magnetic field only.
F= q(v×B)

= qvBsin𝜃
 For maximum force 𝜃=90°
Fmax = qvB
 And hence the electron which are emitted, moved in a right angle with respect to
force.
 If the magnetic field strength is sufficiently large enough, then the electrons emitted
will return back to the cathode with high velocity which may destroy the cathode this
effect is called Back heating of cathode.
𝜋 MODE OF OSCILLATION:
o The shape consisting of oscillation can maintain if the phase difference between anode
cavity is
𝑛𝜋
4
where n is the mode of operation and the best result can be obtained for
n=4 =>
𝑛𝜋
4
=𝜋 (for n=4 hence it is called 𝜋 mode operation).
o It is assume that each anode cavity is of
𝜆
4
length, hence a voltage antinodes will exist
at the opening of anode cavity and the lines of forces present due to the oscillation
started by high quality factor device.
o In the above figure the electron followed by path ‘b’ is so emitted that is not
influenced by the electric lines of forces hence it will spend very less time inside the
cavity and doesn’t contribute to the oscillation so it is called unfavourable electron.
o The electron followed by path a is so emitted that is influence by the electric lines of
forces at position 1,2&3 respectively where the velocity increases or decreases, hence
more time spend inside the cavity therefore it is called favourable electron.
o Any favourable electron which are emitted earlier or later with respect to reference
electron (let a) may be bunch together due to change in velocity by the effect of
electric lines of forces. This type of bunching is called phase focusing effect.
o Electrons emitted from the cathode may rotate around itself in a confined area in a
shape of spoke (spiral) at a angular velocity and before delivering the energy to the
anode cavity. They will rotate until they reach the anode and completely absorbed by
them. Hence the magnetron are also called travelling wave magnetron.
CUT OFF MAGNETIC FIELD (BC):
o Assume a cylindrical magnetron whose inner radius is ‘a’ and outer radius is ‘b’ and
the magnetic field is as shown in the figure. Under the effect of magnetic field the
electrons will rotate in a circular path at any point the force electron will be balance by
the centrifugal force.
𝑚 𝑣2
𝑟
= qvBz
⟹ v =
𝑞Bz
𝑚
𝑟
⟹
𝑣
𝑟
=
𝑞Bz
𝑚
⟹𝜔 =
𝑞Bz
𝑚
⟹f =
1
2𝜋
(
𝑞Bz
𝑚
)
In cylindrical coordinate system the equation of motion is given as

=>
1
𝜕
𝑑
𝑑𝑡
(γ²
𝑑𝜃
𝑑𝑡
)=ω
𝑑𝑟
𝑑𝑡
=>
𝑑
𝑑𝑡
(𝑟²
𝑑𝜃
𝑑𝑡
)=w
𝑑𝑟
𝑑𝑡
.r
=> r² (
𝑑𝜃
𝑑𝑡
) =
𝜔𝑟²
2
+k
The constant k can be calculated using boundary condition.
At r=a,
𝑑𝜃
𝑑𝑡
=0
 0=
𝜔 𝑎2
2
+ 𝑘
 K=−
𝜔 𝑎2
2
…………(1)
The value of k in equation (1)
 r²
𝑑𝜃
𝑑𝑡
=
𝜔
2
(𝑟2
− 𝑎²)……………(2)
At r=b the equation (2) becomes
 b²
𝑑𝜃
𝑑𝑡
=
𝜔
2
(𝑏2
− 𝑎²)
 b
𝑑𝜃
𝑑𝑡
=
𝜔
2𝑏
(𝑏2
− 𝑎²)…………….(3)
Due to electric field only, the electrons move radially from cathode to anode.

1
2
𝑚𝑣2
= 𝑞 𝑉dc
 𝑣 =
2𝑞𝑉
𝑚
dc
But inside the cavity the velocity of electron has two components
 v² =vr²+v𝜃²

2𝑞𝑉
𝑚
dc
=(
𝑑𝑟
𝑑𝑡
)²+(r
𝑑𝜃
𝑑𝑡
)
At r=b,
𝑑𝑟
𝑑𝑡
=0

2𝑞𝑉
𝑚
dc
=0+(b
𝑑𝜃
𝑑𝑡
)²
 b
𝑑𝜃
𝑑𝑡
=
2𝑞𝑉
𝑚
dc
…………..(4)
Comparing equation (3) & (4)
𝜔
2𝑏
(𝑏2
− 𝑎²)=
2𝑞𝑉
𝑚
dc
 1
2𝑏
𝑞𝐵
𝑚
z
(b²-a²)=
2𝑞𝑉
𝑚
dc
(at r=b ,Bz = Bc)

Bc =
8𝑚𝑉𝑑𝑐
𝑏(1− 𝑎²
𝑏²)
𝑏(1− 𝑎²
𝑏²)
Vdc=
𝑞
8𝑚
b² (1 − 𝑎²
𝑏²) Bz²

MICROWAVE PROPAGATION
Line of Sight (LOS) Propagation:
Analog microwave communication system include LOS and over the horizon (OTH)
analog communication systems. LOS communication is limited by horizon due to
earth’s curvature i.e. the transmission distance is determined by the height of the
antenna above the earth in view of the horizon limitation. Microwaves are normally
bent or refracted beyond the optical horizon (horizon visible to eyes). However due to
atmospheric refractive changes, the radio horizon could even be less than the optical
horizon at times.
The height of the microwave tower should be such that the radio beam is not
obstructed by high rise buildings, trees or mountains. LOS microwave systems have
shorter installation time, high flexible channel capacity and better adaptation to
difficult terrains and natural barriers. LOS microwave system operates in the 14Hz to
10GHz frequency range. Above 10GHz however absorption due to rain, fog or snow
may affect the system performance. Above 20GHz it is the absorption due to water
vapour and atmospheric oxygen that limits the performance of an LOS system.
Frequency Division Multiplexing (FDM) is used in all analog microwave LOS
systems that enables several telephone signals to be transmitted over the same carrier.
Normally the 4 KHz telephone channels are grouped as a 12 channel basic group in
the frequency band 60KHz to 108KHz. Further , 5 basic groups form a 60-channel
super group in the frequency band from 312KHz to 552KHz. 16 super groups are
clubbed together to obtain a 960 channel master group.
ABSORPTION OF MICROWAVES BY ATMOSPHERIC GASES:
The transfer of electromagnetic radiation through an atmosphere is linked to its
state (temperature, pressure, and composition) by the refractive index and by
coefficient of absorption and scattering, if any. The absorption coefficient in a medium
is a macroscopic parameter that represents the interaction of incident electromagnetic
energy with the constituent molecules. The interaction is governed by three general
principles.
1. Bohr’s Frequency Condition:
The frequency  of a photon emitted or absorbed by the gas is equal to the
difference of two energy levels (Ea-Eb) of the gas, divided by Plank’s constant h.

2. Einstein’s laws of emission and absorption:
If Ea is higher than Eb, the probability, given initial state a, of stimulated emission
of a photon by a transition from state a to state b is equal to the probability, given
initial state b, of absorption of a photon by a transition from b to a. Hence the net
absorption is proportional to the difference in thermodynamic probabilities (Pa-Pb)
of two states.
3. Dirac’s Perturbation Theory:
For the electromagnetic field to include transitions between states a and b, the
operator with which the field interacts must have a non-zero matrix element linking
the two states. For wavelengths that are very long compared to molecular
dimensions, this operator is the dipole moment.
ABSORPTION OF MICROWAVES BY WATER VAPOUR AND
PRECIPITATES:
Water vapor and fog are the most influencing parameters when microwave
propagates through the atmosphere. At high frequencies above about 10GHz,
electromagnetic radiation starts interacting with the neutral atmosphere and also with
the various metrological parameters, in particular, precipitation, producing absorption
of energy and thus attenuation of signal levels. In addition to absorption by molecular
oxygen, molecules of water vapor also interact with electromagnetic radiation in the
microwave and millimeter wave regions. The water vapor molecule being a permanent
electric dipole produces rotational transitions of the order of 104
times stronger than
that of the magnetic transitions of the oxygen molecule. So, even though the
abundance of water vapor in the atmosphere is considerably less than the oxygen, it
can produce significant level of attenuation near the resonant frequencies. Water vapor
attenuation is found to depend quadratically on water vapor density, particularly at
high densities, above about 12g/m3
.

Microwave Engineering Lecture Notes

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Microwave Engineering Lecture Notes (20)

More from FellowBuddy.com (20)

Recently uploaded (20)

Microwave Engineering Lecture Notes