Npm s350 specsheet
0 likes232 views
The document provides specifications for Nippon Pulse linear shaft motors models S350D, S350T, and S350Q. It lists technical details such as continuous and peak forces, electrical specifications, thermal specifications, force-duty curves, and dimensional details. Stroke lengths for the motors range from 100mm to 2500mm.
Npm s350 specsheet
- 1. Nippon Pulse Your Partner in Motion Control NPM S350 Linear Shaft Motor L = See Shaft Length L1 = Usable Stroke + A L2 = See Shaft Support Length A = See Moving Coil Length P = See Moving Coil Screw Pitch Electrical Specs S350D S350T S350Q Continuous Force1 104N 148N 190N Continuous Current1 1.5Arms 1.5Arms 2.7Arms Peak Force2 416N 592N 760N Peak Current2 6.0Arms 6.0Arms 10.8Arms Force Constant (Kf) 69N/Arms 99N/Arms 70N/Arms Back EMF (Ke) 23V/m/s 33V/m/s 23V/m/s Resistance 25°C,3 13.8Ω 20.2Ω 6.9Ω Inductance3 21.8mH 33mH 10.9mH Electric Time Constant 1.58ms 1.63ms 1.58ms Fundemental Motor Constant (Km) 18.66N√W 21.95N√W 26.79N√W Magnetic Pitch (North-North) 120mm 120mm 120mm All specifications are for reference only. Specifications may change depending on servo driver selected. Consult Nippon Pulse. 1) Based on a temp rise of coil surface of 110°K over 25°C ambient temperature stalled forcer, and no external cooling or heat sinking Addition of 25 cm x 25 cm x 2.5 cm aluminum heat sink increases continuous force by 20% 2) Can be maintained for a maximum of 40 seconds, higher forces and current possible for short periods of time, consult Nippon Pulse 3) All winding parameters listed are measured line-to-line (phase-to-phase) Thermal Specs S350D S350T S350Q Max Phase Temperature4 135°C 135°C 135°C Thermal Resistance (Coil) (Kq) 3.5°C 2.4°C 2.2°C 4) The standard temperature difference between the coil and the forcer surface is 25°C Forcer Specs S350D S350T S350Q Forcer Length (A) 160mm 220mm 280mm Forcer Width 60mm 60mm 60mm Forcer Screw Pitch (P) 140mm 200mm 260mm Forcer Weight 1.3kg 1.9kg 2.4kg Force - Duty Curve Gap S 350D 1.00mm 1.00mm 1.00mm Force - Duty Curve S 350Q Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 S350D Force Duty Curve S350Q Force Duty Curve Unless Otherwise Specified: Dimensions are in mm Tolerances are as follows: Dimension (mm) - 6 7 - 30 31 - 120 121 - 315 316 - 1000 1001 - 2000 2000 - Tolerance (mm) ±0.1 ±0.2 ±0.3 ±0.5 ±0.8 ±1.2 ±1.5 * Note 1 Cable length 300mm The bending radius of the motor cable should be 36.6mm (wire diameter 6.1 * 6) as suggested by the wire manufacturer. This radius should be maintained. Use supplied connector to attach the proper high flex cable as required by your application. Total Length Movable Range Forcer Length Forcer Screw Pitch Support Length Stroke Length Motor Cable Length dep Setting Pitch Bending Radius Reference End Yellow Mark Serial Number Label Mounting Surface Gap Bore 1000 900 800 700 600 500 400 300 200 100 0 0 20 40 60 80 100 Force (N) Duty(%) 2 0 °C 4 0 °C 6 0 °C 8 0 °C 1 1 0 °C 1800 1600 1400 1200 1000 800 600 400 200 0 www.electromate.com sales@electromate.com 0 20 40 60 80 100 Force (N) Duty(%) ELECTROMATE 2 0 °C 4 0 °C 6 0 °C 8 0 °C 1 1 0 °C Sold & Serviced By:
- 2. Shaft Length (mm) Shaft Mass (kg) Stroke S350D S350T S350Q 150 410 470 530 200 460 520 580 250 510 570 630 300 560 620 680 350 610 670 730 400 660 720 780 450 710 770 830 500 760 820 880 550 810 870 930 600 860 920 980 650 910 970 1030 700 960 1020 1080 750 1010 1070 1130 800 1100 1160 1220 850 1150 1210 1270 900 1200 1260 1320 950 1250 1310 1370 1000 1300 1360 1420 1050 1350 1410 1470 1100 1400 1460 1520 1150 1450 1510 1570 1200 1500 1560 1620 1250 1550 1610 1670 1300 1600 1660 1720 1350 1650 1710 1770 1400 1700 1760 1820 1450 1750 1810 1870 1500 1800 1860 1920 1550 1910 1970 2030 1600 1960 2020 2080 1650 2010 2070 2130 1700 2060 2120 2180 1750 2110 2170 2230 1800 2160 2220 2280 1850 2210 2270 2330 1900 2260 2320 2380 1950 2310 2370 2430 2000 2360 2420 2480 Lead Wire Wire Type UL 2464 Wire AWG 16 U Phase Red V Phase White W Phase Black 300mm lead wire bare leads The bending radius of the motor ca-ble should be 36.6mm as suggested by the wire manufacturer. CE Type Motor Cable Support and Bending S350 Linear Shaft Motor Connector (Motor Cable) Hall Effect Cable Stroke Support Length Max. bending 0~750 50mm 0.00mm 751~1000 70mm 0.30mm 1001~1500 70mm 0.90mm 1501~max 100mm 1.00mm Shaft Diameter (D) - 35mm ±0.2 Total Length (L)=Stroke (S)+Forcer Length (A)+(Support Length (L2)x2) Forcer Spacing Distance Forcer Spacing Distance Sensor Cable Specs Shaft Size (D) Forcer Size (A) Usable Stroke Options Options S X XXXX XX XX Receptacle Housing VLR-03V Plug Housing VLP-03V Retainer VLS-03V Pin Contact SVM-61T-P2.0 Socket Contact SVF-61T-P2.0 To be installed by the user Spec S350T S350Q Forcer Spacing Distance 20mm 20mm Pole (N/S) Distance 60mm 60mm Forcer Length 220mm 280mm Flip Forcers No Yes — — — — — D: Double (2) windings T: Triple (3) windings Q: Quadruple (4) windings 100-2000mm ST: Standard WP: Waterproof DA: Digital Hall Effect CE: CE type motor Blank: Standard FO: Forcer Only SO: Shaft Only XX: Two digit for custom motor Part Numbering System Wire Type UL 1330 Wire AWG 24 U Phase Red V Phase White W Phase Black Ground Wire UL 1330 Wire AWG 20 Frame Ground Green/Yellow 300mm lead wire bare leads The bending radius of the motor cable should be 16.96mm as suggested by the wire manufacturer. * Note 1 The bending radius of the motor cable should be R27.6mm (wire diameter 4.6 * 6) as suggested by the wire manufacturer. This radius should be maintained. Use supplied connector to attach the proper high flex cable as required by your application. Wire Type UL 758 Wire AWG 28 VCC White/Red GND White/Black Sensor 1 Orange/Red Sensor 2 Orange/Black Sensor 3 Gray/Red No Connec. Gray/Black 400mm lead wire bare leads The bending radius of the motor ca-ble should be 27.6mm as suggested by the wire manufacturer. Tandem Forcer Hall Effect Specs Wire Type UL 758 Wire AWG 28 VCC White/Red GND White/Black Sensor 1 Orange/Red Sensor 2 Orange/Black Sensor 3 Gray/Red The bending radius of the sensor cable should be R36.6mm (wire diameter 6.1 * 6) as suggested by the wire manufac-turer. This radius should be maintained. Attach the proper high flex cable as re-quired by your application. 350 Stroke lengths available from 100mm to 2500mm. Contact Nippon Pulse for more information. Stroke S350D S350T S350Q 150 2.7 3.1 3.5 200 3 3.4 3.8 250 3.4 3.8 4.2 300 3.7 4.1 4.5 350 4 4.4 4.8 400 4.4 4.8 5.1 450 4.7 5.1 5.5 500 5 5.4 5.8 550 5.3 5.7 6.1 600 5.7 6.1 6.5 650 6 6.4 6.8 700 6.3 6.7 7.1 750 6.7 7.1 7.5 800 7.3 7.7 8.1 850 7.6 8 8.4 900 7.9 8.3 8.7 950 8.3 8.6 9 1000 8.6 9 9.4 1050 8.9 9.3 9.7 1100 9.2 9.6 10 1150 9.6 10 10.4 1200 9.9 10.3 10.7 1250 10.2 10.6 11 1300 10.6 11 11.4 1350 10.9 11.3 11.7 1400 11.2 11.6 12 1450 11.6 11.9 12.3 1500 11.9 12.3 12.7 1550 12.6 13 13.4 1600 12.9 13.3 13.7 1650 13.3 13.7 14.1 1700 13.6 14 14.4 1750 13.9 14.3 14.7 1800 14.3 14.7 15.1 1850 14.6 15 15.4 1900 14.9 15.3 15.7 1950 15.2 15.6 16 2000 15.6 16 16.4 Sold & Serviced By: ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com