System of smart detection and control to electrical energy for saving of electrical energy consumption

Bulletin of Electrical Engineering and Informatics
Vol. 10, No. 5, October 2021, pp. 2454~2465
ISSN: 2302-9285, DOI: 10.11591/eei.v10i5.2826 2454
Journal homepage: http://beei.org
System of smart detection and control to electrical energy for
saving of electrical energy consumption
R. Roslina1
, Afritha Amelia2
, Heru Pranoto3
, Bakti Viyata Sundawa4
1
Department of Computer and Informatics Technology, Politeknik Negeri Medan, Indonesia
2,3,4
Department of Electrical Engineering, Politeknik Negeri Medan, Indonesia
Article Info ABSTRACT
Article history:
Received Jan 22, 2021
Revised Apr 13, 2021
Accepted Aug 19, 2021
Public campus has a mandate to saving of electrical energy. Electrical energy
consumption is often wasteful in building. There is tendency wasteful by user.
Electronic equipment is often still turn on at idle time. Only a few students
want to turn off the equipment and shut down the computer. Saving of
electrical energy is not only at idle time but it can be improved into
operational hour. It is not depending on idle time or operational hours, but
depends on human presence. Implementation of electrical energy saving has
to be supported by frugal behavior and equipment technology. In this study,
we name system of smart detection and control to electrical energy (Sisdece).
This system is consist of hardware and software. Hardware applies passive
infrared sensor (PIR) sensor, wireless sensor network (WSN), microcontroller
ESP32, access point, relay. Software use C++, hypertext preprocessor (PHP),
hypertext markup language (HTML) and android studio. Result of
measurement has been done in a month during November 2020. Average of
energy saved is 12.51 kWh and total of electrical energy is 105.86 kWh.
Comparison of energy saved to electrical energy is 11.81%. This is a
significant reduction to electrical bill. The result is expected as benchmark of
electrical energy management in Politeknik Negeri Medan (POLMED).
Keywords:
Idle time
Operating hours
Saving energy
Smart control
Smart detection
This is an open access article under the CC BY-SA license.
Corresponding Author:
R. Roslina
Department of Computer and Informatics Technology
Politeknik Negeri Medan
1 Almamater Road, University of Sumatera Utara, Medan 20155, Indonesia
Email: roslina@polmed.ac.id
1. INTRODUCTION
Saving of electrical energy is a mandatory requirement for campus activity. Based on regulation of
energy and mineral resources ministry No.13/2012 about electrical saving consumption at state buildings,
official residences, public street lighting, decorative lights, and billboards. Public campus is one of state
owned building. For this reason, public campus must carry out the mandate. Mandate must be implemented
in all lines, namely academics, infrastructure, and buildings. The building sectors such as study room, office,
library, laboratory, commercial place, and workshop need the highest of electrical energy consumption.
Utilization of air conditioner (AC) is the highest of electrical energy consumption (57%), lighting (19%), lifts
and pumps (18%), and other equipment (6%) [1]. Energy consumption is often wasteful and not for
productive something. There is a tendency of wasteful by user. Several campuses have done mandate of
energy saving namely doing optimization of energy saving device and providing energy saving guidelines to
change user behavior. Study has done to find how far level of knowledge, attitudes and behavior impact to
energy consumption [2]. Wasteful behavior is the biggest factor to be negative impact to energy
consumption. Inefficiency of energy consumption is also caused by cheap energy policy applied by

Bulletin of Electr Eng & Inf ISSN: 2302-9285 
System of smart detection and control to electrical energy (Sisdece) for saving of electrical … (R. Roslina)
2455
Indonesian Government [3]. In general, all users must be considered that saving of electrical energy has to be
supported by frugal behavior and equipment technology.
Idle time or break session is an unproductive time. It always happens in all office, both educational
institution and goverment. Electronic equipment is often still turn on at idle time. There are two large
building such as main office and laboratory/workshop. Electrical wasteful phenomenon often occurs in that
place. Computers, alternating current (AC), electric lamps are always turn on although there is no human at
main office. Only a few students want to turn off laboratory equipment and shut down the computer at
laboratory/workshop. It takes many manpower and need a long time to turn off electronic equipment on each
floor and each building. This is ineffective and inefficient. There are researches on saving of electrical energy
such as monitoring electrical equipment using ATmega 328P-PU microcontroller [4]. Power consumption
measurement in microcontroller based on system [5]. Energy efficiency in toilets and enclosed corridors by
automatic switches and detection of human activities [6]. Home with energy management system (HEMS)
[7]. Smart home control by raspberry pi and arduino uno [8]. Energy management and planning smart city
[9]. Design of smart system to control energy in idle time [10]. All the researches above have been done and
their technology controlled utilization of electrical energy at idle time.
Saving of Electrical Energy is not only at idle time (break session) but it can be improved into
operational hours. Electrical equipment can be controlled by automatic according to presence of human using
PIR sensor and LM35 sensor. According to this fact, electrical energy consumption can be controlled. It is
not depending on idle time or operational hours, but depends on human presence. Therefore, we name our
research with the system of smart detection and control of electrical energy (Sisdece). PIR motion sensor can
detect human activity in workspace. If there is no human activity then Sisdece will turn off electrical current.
If there is human activity then Sisdece will turn on electrical current again. Sisdece hardware design applies
PIR motion sensor, wireless sensor networks (WSN), microcontroller ESP32 as IoT component, access point,
relay and other supporting components. Sisdece software design use C++ programming, web programming
(PHP and HTML) and android studio as graphical user interface (GUI) for mobile programming. Data
storage use cloud based on thingspeak technology. Electrical energy load will be collected during idle time
and operational hours. Collected data will be analyzed to predict saving of electrical energy consumption in a
certain period. The result of this study is expected to use as benchmark of electrical energy management in
Politeknik Negeri Medan (POLMED).
2. RESEARCH METHOD
This research was carried out in five stages. First, analysis of object detection. Passive infra red
(PIR) sensor is used to detect human activity. There are 2 infrared in PIR sensor. Both infrared will produce
the same output in idle stage. When an object moves, infrared will produce unequal output. This is due to
object movement [11]. Type of PIR sensor is HC-SR501. Range of power supply is 4.2 V-20 V and
consumes electrical current of 65 mA. PIR sensor will high stage (logic 1) when it detects object. Voltage is
3.3 V in high stage. Distance sensitivity of HC-SR501 is about 3 m to 7 m and time delay of high stage is 3
second to 5 second. Features of HC-SR501 as shown in Figure 1.
Figure 1. Features of HC-SR501 [12]

 ISSN: 2302-9285
Bulletin of Electr Eng & Inf, Vol. 10, No. 5, October 2021 : 2454 – 2465
2456
Second, analysis of proposed detection and control system. Problem analysis has been described
before that electrical energy consumption can be controlled by depending on human activity. Sisdece will
detect and cut off electrical current automatically during operational hours and idle time when there is no
human in the room. PIR sensor provides boolean data when there is human and no human. PIR sensor gives
logic ‘1’ for human activity and logic ‘0’ for no human activity. PIR sensor is connected to controller.
Microcontroller ESP32 acts as controller of the system. Controller is connected to other devices and
webserver as well. Controller use communication protocol RS485 to communicate to energy meter. Energy
meter reads electrical data and feedback to controller (microcontroller ESP32) by digitally. Besides that
power system is maintained by miniature circuit breaker (MCB). MCB as main power breaker. There is 2
MCB which is controlled by controller. MCB 1 keeps energy meter to stay safety. If there is short circuit
(SC) in energy meter then MCB 1 breaks the electrical power or disconnection. MCB 2 as electrical
termination and it keeps the electrical devices to stay safety. Air conditioner (AC) can be connected directly
to MCB 2. Lamp is controlled by a relay in controller. Controller circuit as shown in Figure 2.
Figure 2. Controller circuit
Third, connection of controller device and webserver. At this stage, communication between
controller device and webserver use wi-fi feature in microcontroller ESP32. It has 25 general purpose input
output (GPIO) pins and analog inputs. It can be programmed to store data via internet. The circuit of
controllers can communicate with the web server via a wi-fi network. Communication is done by two-way
communication via message queuing telemetry transport (MQTT) protocol. MQTT gives a mechanisms to
asynchronous communication. It has a range of implementations, and it is operational on internet protocol
(IP) [13]. MQTT is an extension of the open protocol message for queuing telemetry transport [14]. MQTT

2457
can be design for synchronizing IoT device with multiple client nodes [15]. Advantage of MQTT is lite. This
is suitable for devices with limited resources and it helps energy efficiency. In addition, by MQTT
publish/subscribe model provides clients independence. When one client is down, whole system can still
continue to work properly. We decide that MQTT is more suitable for IoT application which is able to send
faster with limited bandwidth resources. Connection of controller device and webserver as shown in Figure 3.
Figure 3. Connection of controller device and webserver
Fourth, sisdece software design. Design of sisdece software use C++ programming and android
studio as graphical user interface (GUI) on mobile programming. Data storage use cloud based on thingspeak
technology. Figure 4 is flowchart of sisdece algorithm as reference to develop software application.
Embedded system has to be main part for programming on IoT devices. Many programmers are comfortable
with embedded system. Many applications have been built using embedded system such as artificial vision
ability [16], activities of education [17], smart taxi in smart city [18], to reduce vehicles congestion on traffic
lights [19], to monitor pH and temperature level [20], implementation of smart wireless for aquaculture [21],
to detect water quality [22], to measure water quality using picture from smartphone [23], to monitor pH, and
temperature level using wireless sensor network (WSN) [24].
When sisdece device is activated, controller (microcontroller ESP32) will initialize and then it will
be connected to wifi to read data from memory. Sisdece device uses the time taken from internet via NTP
(network time protocol) server and real-time clock (RTC). RTC is used as backup if system is not connecting
to internet. According to Figure 3, system has 2 modes, namely automatic and manual. In automatic mode,
system will divide into 2 session, namely operational hours and idle time. Operational hours and idle time are
set by the time. During operational hours, electrical current to lamp and AC will be turned on according to
time session. If operational hours is the end and then next session is idle time. At idle time, electrical current
to lamp and AC will be cut along this time. In manual mode, PIR sensor is utilized to detect human activity.
If there is human activity then electrical current is turn on, and vice versa. System will send data and status to
webserver for displayed. Any changes will be stored into memory and last condition will be displayed at
system restarted. Electrical data is taken from energy meter such as voltage (Voltage), current (Ampere),
power (Watt), and electrical energy (Watt Hour). System calculates daily power consumption in a room and
system will reset daily power consumption data at 00:00 a.m. Sisdece performance can be monitored by PC
and smartphone via internet. Fifth, software testing. Programming is divided into 4 subprogram, such as
controller programming, web programming and mobile programming. Controller programming is consist of:
a. PIR sensor data
b. Read PIR sensor data
c. Read electrical data from energy meter
d. Send electrical data to server using MQTT protocol

 ISSN: 2302-9285
2458
Figure 4. Flowchart of Sisdece algorithm
This is a sample for reading of PIR data using C++:
bool bacaPIR(){
flagSample = false;
j = 0;
while(j < 4){
pirStat[j] = false;
j++;
}
if(pirSens[0] == false){
if(digitalRead(PIN_PIR_1) == HIGH){
pirStat[0] = true;
}
else {
pirStat[0] = false;
}
}

2459
pirStat[1] = true;
}
else{
pirStat[1] = false;
}
}
pirStat[2] = true;
}
else{
pirStat[2] = false;
}
}
pirStat[3] = true;
}
else{
pirStat[3] = false;
}
}
j = 0;
while(j < 4){
if(pirStat[j] == pirSens[j] == true){
flagSample = true;
break;
}
j++;
}
return flagSample;
}
3. RESULTS AND DISCUSSION
3.1. Sisdece prototype installation
Sisdece prototype has been installed in Telecommunication Lab. Politeknik Negeri Medan. Sisdece
prototype is installed at one of lecture room. This is consist of control panel, PIR sensor and LCD display, as
shown in Figure 5.
(a) (b) (c)
Figure 5. Sisdece prototype, (a) control panel, (b) PIR sensor, (c) LCD display
3.2. Software development
Measurement can be monitored by PC and smartphone. Parameters of measurement are voltage (V),
current (A), power (W), and electrical energy (Wh). Sisdece software interface is shown in Figure 6.

 ISSN: 2302-9285
2460
Figure 6. Sisdece software interface
3.3. Data collection
Data has been collected by Sisdece based on predetermined sessions, namely idle time and operating
hours. Data has been collected during a month. It starts from 2 November 2020 up to 30 November 2020 and
7.00 a.m up to 6.00 p.m. Usage of Sisdece on the first day is not able to calculate the saving energy. Sisdece
accumulates data along 24 hours. Result of measurement on first day is shown in Table 1. Usage of Sisdece
on second day gives us saving energy data. Average value is 1,189.43 Wh or 1.19 kWh in that day. Usage of
Sisdece gives average value 58.86 Wh or 0,058 kWh on third day. Results of measurement can be seen at
Table 1, Table 2, and Table 3. Measurement is continued during a month on November 2020.

2461
Table 1. Result of measurement on 1st
day
Voltage
(V)
Current
(A)
Power
(kW)
Electrical
energy (Wh)
Operational
hour
Idle time
(second)
Information
234.85 0.39 0.08 0.00 7:00 a.m Not calculated While operating hours starting
225.10 5.94 1.18 1078.92 8:00 a.m Not calculated Operational session
226.41 6.65 1.32 7022.65 1:00 p.m Not calculated Operational session
224.73 5.74 1.14 12759.82 6:00 p.m Not calculated While operating hours ending
Table 2. Result of measurement on 2nd
day
Voltage
(V)
Current
(A)
Power
(kW)
Electrical
energy (Wh)
Operational
hour
Idle time
(second)
Information
Energy saved
(Wh)
235.00 0.38 0.08 0.00 7:00 a.m 0 While operating hours starting 0.00
224.75 5.93 1.17 489.96 8:00 a.m 1,795 Operational session 1,045.14
225.56 6.34 1.26 1,726.99 9:00 a.m 0 Operational session 392.75
225.57 6.34 1.26 2,944.03 10:00 a.m 0 Operational session 3,887.42
224.75 5.93 1.17 3,728.94 11:00 a.m 1,009 Operational session 302.60
225.18 6.15 1.22 4,744.62 12:00 a.m 298 Operational session 0.00
226.18 6.66 1.33 4,966.19 1:00 p.m 2,818 Operational session 3,894.02
225.56 6.34 1.26 6,120.05 2:00 p.m 178 Operational session 299.62
225.16 6.14 1.22 7,315.79 3:00 p.m 0 Operational session 4,207.27
225.06 6.08 1.21 7,929.00 4:00 p.m 1,768 Operational session 0.00
224.77 5.94 1.17 9,064.19 5:00 p.m 119 Operational session 1,045.14
224.38 5.73 1.13 9,665.72 6:00 p.m 1,567 While operating hours ending 392.75
Average of energy saved 1,189.43
Table 3. Result of measurement on 3rd
day
Voltage
(V)
Current
(A)
Power
(kW)
Electrical
energy (Wh)
Operational
hour
Idle time
(second)
Information
Energy saved
(Wh)
234.20 0.38 0.08 0.00 7:00 a.m 0 While operating hours starting 0.00
223.80 6.02 1.17 178.08 8:00 a.m 2753 Operational session 136.18
235.10 0.01 0.00 4694.76 1:00 p.m 0 Operational session 0.00
234.90 0.01 0.00 4702.52 6:00 p.m 0 While operating hours ending 0.00
Average of energy saved 58.86
By overall, measurement has been done which to drawn into graphic. Comparative analysis will be
seen easier if we draw in graphic. Some information is easier to explain when represented by visual. Visual
information is very important for reasoning, imagining and problem solving [25], [26]. Graphic has served
user to find out ideas and solve problem. Graphic gives a thousand words [27]. In this study, comparative
analysis graphic toward power (kW), electrical energy (kWh), energy saved (kWh) and idle time (hour).
Increasing of energy saved is directly proportional to idle time. Increasing of electrical energy is inversely
proportional to idle time. In Figure 7, it has not been able to show a trend of energy saved. It caused by
Sisdece has not finished yet to calculate idle time. On second day usage, Sisdece starts accumulation the day
before. In Figure 8, we can see the directly proportional energy saved between idle time. Energy saved (green
line) will increase if idle time (purple line) is long. In Figure 9, we can see the inversely proportional
electrical energy between idle time. Electrical energy (red line) will increase if idle time (purple line) is short.
Idle time mechanism is made by detection and control section in Sisdece. They are PIR sensor,
microcontroller ESP32 and relay contactor.
Result of measurement has been done in a month. This is to find out a trend of energy saving. Figure 10
shows that electrical energy graphic (red line) against energy saved graphic (green line). This is inversely
proportional. Daily data can be made into average value and then it is recapitulated during a month.

 ISSN: 2302-9285
2462
Implication of energy reduction can be estimated in term of cost saving. According to Figure 10, average of
energy saved is 12.51 kWh along November 2020. Total electrical energy along November 2020 is 105.86
kWh. If we compare between electrical energy and energy saved then Sisdece has saved 11.81%. This is a
significant reduction. Estimation of cost saving can be seen in Table 4.
According to Table 4, we are able to know how much cost that can be saved. Sisdece gives a
significant saving. Annual energy saved is 150.12 kWh/year and annual cost saving is IDR 220,226.04. This
cost saving is only for 1 lecture room. What if Sisdece is implemented to all lecture room at campus. It will
effect to short term expense.
Figure 7. Measurement result on first day
Figure 8. Measurement result on second day
Figure 9. Measurement result on third day

2463
Figure 10. Accumulation of measurement in a month
Table 4. Estimation of cost saving
Criteria Estimation of cost saving use Sisdece prototype
Average of electrical energy per a month (kWh) 105.86
Average of energy saved per a month (kWh) 12.51
Annual electrical energy consumption (kWh/year) 1,270.32
Annual energy saved (kWh/year) 150.12
Rates (IDR per kWh) 1,467
Monthly cost (IDR) 155,296.62
Annual cost (IDR) 1,863,559,44
Monthly cost saving (IDR) 18,352.17
Annual cost saving (IDR) 220,226.04
4. CONCLUSION
Sisdece is able to detect and control electrical energy consumption in room both in idle time and
operating hour. They switch off electrical energy during operational hour if there is no human activity. We
can find out the energy saved by usage of Sisdece. Data of measurement can be known daily, monthly and
annually. According to measurement in November 2020, energy saved is 12.51 kWh and cost saving is IDR
18,352.17. This is a potential movement in energy saving. Saving value can be estimated for 1 year and it is
expected to be beneficial to campus management. For further research, it is necessary to add Sisdece with
ability to detect human movement by capturing based on image processing.
ACKNOWLEDGEMENTS
Authors wishing to acknowledge DIPA of Politeknik Negeri Medan who funded this research
through scheme of Penelitian Produk Terapan (PPT) 2020. I would like to thank to Director of Politeknik
Negeri Medan, Head of P3M Politeknik Negeri Medan and anonymous persons one by one who help me
during the process.
REFERENCES
[1] R. Saidur, "Energy consumption, energy savings, and emission analysis in Malaysian office buildings," Energy
policy, vol. 37, pp. 4104-4113, 2009, doi: https://doi.org/10.1016/j.enpol.2009.04.052.
[2] S. Sunardiyo, Purwanto, and Hermawan, "Survey of Energy Conservation Behavior Measures for the Academic
Community on Campus: A Case in Semarang State University, Indonesia," Advanced Science Letters, vol. 23, pp.
2305-2307, 2017.
[3] D. Hakam and A. Asekomeh, "Gas monetisation intricacies: Evidence from Indonesia," International Journal of
Energy Economics and Policy, vol. 8, no. 2, pp. 174-181, 2018.
[4] M. Caruso, et al., "Design and experimental characterization of a low-cost, real-time, wireless AC monitoring
system based on ATmega 328P-PU microcontroller," 2015 AEIT International Annual Conference (AEIT), 2015,
pp. 1-6, doi: 10.1109/AEIT.2015.7415267.
[5] A. Di Nisio, T. Di Noia, C. G. C. Carducci, and M. Spadavecchia, "High Dynamic Range Power Consumption
Measurement in Microcontroller-Based Applications," in IEEE Transactions on Instrumentation and Measurement,
vol. 65, no. 9, pp. 1968-1976, Sept. 2016, doi: 10.1109/TIM.2016.2549818.

 ISSN: 2302-9285
2464
[6] I. R. Martini, K. Adiyarta, and M. Suparmoko, "An Effort to Lower Electricity Bill in University Building by
Automatic Lighting Switches Application," Pertanika J. Soc. Sci. & Hum, vol. 26, pp. 11-20, 2018.
[7] B. Zhou, et al., "Smart home energy management systems: Concept, configurations, and scheduling strategies,"
Renewable and Sustainable Energy Reviews, vol. 61, pp. 30-40, August 2016, doi: 10.1016/j.rser.2016.03.047.
[8] H. H. Hadwan and Y. Reddy, "Smart home control by using raspberry pi and arduino uno," Int. J. Adv. Res.
Comput. Commun. Eng, vol. 5, no. 4, pp. 283-288, April 2016, doi: 10.17148/IJARCCE.2016.5473.
[9] C. F. Calvillo, A. Sánchez-Miralles, and J. Villar, "Energy management and planning in smart cities," Renewable
and Sustainable Energy Reviews, vol. 55, pp. 273-287, March 2016, doi: 10.1016/j.rser.2015.10.133.
[10] R. Roslina, A. Amelia, D. Hartama, and N. Fahmi, "Design of Smart System to Control Energy in Idle Time,"
Journal of Physics: Conference Series, vol. 1501, no. 1, p. 012002, 2020.
[11] K. C. Sahoo and U. C. Pati, "IoT based intrusion detection system using PIR sensor," 2017 2nd IEEE International
Conference on Recent Trends in Electronics, Information & Communication Technology (RTEICT), 2017, pp.
1641-1645, doi: 10.1109/RTEICT.2017.8256877.
[12] ‘‘How HC-SR501 PIR Sensor Works & Interface It With Arduino,’’ 2021. [Online]. Available.
https://lastminuteengineers.com/pir-sensor-arduino-tutorial/.
[13] M. B. Yassein, M. Q. Shatnawi, S. Aljwarneh, and R. Al-Hatmi, "Internet of Things: Survey and open issues of
MQTT protocol," 2017 International Conference on Engineering & MIS (ICEMIS), 2017, pp. 1-6, doi:
10.1109/ICEMIS.2017.8273112.
[14] U. Hunkeler, H. L. Truong, and A. Stanford-Clark, "MQTT-S-A publish/subscribe protocol for Wireless Sensor
Networks," 2008 3rd International Conference on Communication Systems Software and Middleware and
Workshops (COMSWARE '08), 2008, pp. 791-798, doi: 10.1109/COMSWA.2008.4554519.
[15] A. Shaout and B. Crispin, "Using the MQTT Protocol in Real Time for Synchronizing IoT Device State," The
International Arab Journal of Information Technology, vol. 15, no. 3A, pp. 515-521, 2018.
[16] A. Abdurrasyid, I. Indrianto, and R. Arianto, "Detection of immovable objects on visually impaired people walking
aids," TELKOMNIKA Telecommunication, Computing, Electronics and Control, vol. 17, no. 2, pp. 580-585, April
2019, doi: 10.12928/TELKOMNIKA.v17i2.9933.
[17] I. Indrianto, M. N. I. Susanti, R. Arianto, and R. R. A. Siregar, "Embedded System Practicum Module for Increase
Student Comprehension of Microcontroller," TELKOMNIKA Telecommunication, Computing, Electronics and
Control, vol. 16, no.1, pp. 53-60, February 2018, doi: 10.12928/telkomnika.v16i1.4194.
[18] I. Indrianto, M. N. I. Susanti, R. R. A. Siregar, and Y. Purwanto, "Smart taxi security system design with internet of
things (IoT)," TELKOMNIKA Telecommunication, Computing, Electronics and Control, vol. 17, no. 3, pp. 1250-
1255, June 2019, doi: 10.12928/TELKOMNIKA.v17i3.10167.
[19] D. Hartanti, R. N. Aziza, and P. C. Siswipraptini, "Optimization of smart traffic lights to prevent traffic congestion
using fuzzy logic," TELKOMNIKA Telecommunication Computing Electronics and Control, vol. 17, no. 1, pp. 320-
327, February 2019, doi: 10.12928/TELKOMNIKA.v17i1.10129.
[20] R. B. Lukito and C. Lukito, "Development of IoT at hydroponic system using raspberry Pi," TELKOMNIKA
Telecommunication Computing Electronics and Control, vol. 17, no. 2, pp. 897-906, April 2019, doi:
10.12928/TELKOMNIKA.v17i2.9265.
[21] A. J. Odey and L. Daoliang, "AquaMesh-design and implementation of smart wireless mesh sensor networks for
aquaculture," American Journal of Networks and Communications, vol. 2, no. 3, pp. 81-87, 2013, doi:
10.11648/j.ajnc.20130203.15.
[22] H. Chen and X. Liu, "A Novel Kind of Smart Monitoring System of Aquaculture," in 2015 2nd International
Conference on Electrical, Computer Engineering and Electronics, June 2015, pp. 369-372.
[23] V. Kılıç, G. Alankus, N. Horzum, A. Y. Mutlu, A. Bayram, and M. E. Solmaz, "Single-image-referenced
colorimetric water quality detection using a smartphone," ACS omega, vol. 3, no. 5, pp. 5531-5536, 2018, doi:
10.1021/acsomega.8b00625.
[24] M. A. Ab Aziz, M. Abas, M. K. A. A. Bashri, N. M. Saad, and M. Ariff, "Evaluating IoT based passive water
catchment monitoring system data acquisition and analysis," Bulletin of Electrical Engineering and Informatics,
vol. 8, no. 4, pp. 1373-1382, December 2019, doi: 10.11591/eei.v8i4.1583.
[26] J. R. Anderson, ‘‘Cognitive psychology and its implications,’’ Macmillan, 2005.
[27] J. H. Larkin and H. A. Simon, "Why a diagram is (sometimes) worth ten thousand words," Cognitive science, vol.
11, no. 1, pp. 65-100, January–March 1987, doi: 10.1016/S0364-0213(87)80026-5.
[28] G. L. Lohse, K. Biolsi, N. Walker, and H. H. Rueter, "A classification of visual representations," Communications
of the ACM, vol. 37, no. 12, pp. 36-50, 1994.
BIOGRAPHIES OF AUTHORS
R. Roslina obtained her Ph.D in Computer Science from University of Sumatera Utara at 2018.
Energyly, she is deputy director of Politeknik Negeri Medan, especially academic affairs. Her
research is mainly focused on smart cities, smart vocational education, smart system.

2465
Afritha Amelia obtained her master’s degree in Multimedia Telecommunication from Institute of
Teknologi Sepuluh November Surabaya at 2009. Energyly, she is a Ph.D student in Computer
Science University of Sumatera Utara. Her research is mainly focused on IoT application and
wireless telecommunication.
Heru Pranoto obtained his master’s degree in Electronic Network from Czech Technical
University, Czech Republic at 2013. Energyly, he is deputy director of Politeknik Negeri Medan,
especially external affairs. His research is mainly focused on IoT application and electronic
devices.
Bakti Viyata Sundawa obtained his master’s degree in Electrical Engineering from University of
Sumatera Utara at 2011. Energyly, he is a lecturer in Electrical Engineering Politeknik Negeri
Medan. His research is mainly focused on IoT application and wireless telecommunication.

System of smart detection and control to electrical energy for saving of electrical energy consumption

More Related Content

What's hot (19)

Similar to System of smart detection and control to electrical energy for saving of electrical energy consumption (20)

More from journalBEEI (20)

Recently uploaded (20)

System of smart detection and control to electrical energy for saving of electrical energy consumption