Interruptsof8085
- 2. CONTENTS Sr no contents 1 Introduction 2 classification of interrupts 3 Hardware interrupt 4 SIM Instruction 5 RIM instruction 6 Block diagram of Hardware interrupt 7 Software interrupt
- 3. what is Interrupt? Interrupt is a mechanism by which an I/O or an instruction can suspend the normal execution of processor and get itself serviced. Generally, a particular task is assigned to that interrupt signal. In the microprocessor based system the interrupts are used for data transfer between the peripheral devices and the microprocessor. INTRODUCTION
- 4. After receiving an interrupt signal from the peripheral, the microprocessor executes current instruction completely. Store the contents of program counter i.e. return address on the stack and then executes interrupts service (ISR) to provide service to the interrupting device. After servicing the device, the microprocessor transfer program control back to the program where interrupt occurs by reloading the content of program counter which has been stored on the stack when an interrupt occurs.
- 5. Main program X Y µp is interrupt ISR RET HLT EXAMPLE:-
- 6. There are 5 interrupt inputs: 1) TRAP(non-maskable) 2) RST7.5 3) RST6.5 4) RST5.5 5) INTR Interrupts pin on IC :-
- 7. CLASSIFICATION OF INTERRUPTS Interrupts Hardware Software Maskable • RST 7.5 • RST 6.5 • RST 5.5 • INTR Non-maskeble • TRAP
- 8. Nonmaskable interrupt The MPU is interrupted when a logic signal is applied to this type of input. Maskable interrupt The MPU is interrupted ONLY if that particular input is enabled. It is enabled or disabled under program control. If disabled, an interrupt signal is ignored by the MPU. HARDWARE INTERRUPTS
- 9. RESPONDING TO INTERRUPTS • Responding to an interrupt may be immediate or delayed depending on whether the interrupt is maskable or non- maskable and whether interrupts are being masked or not. • There are two ways of redirecting the execution to the ISR depending on whether the interrupt is vectored or non- vectored. • Vectored:The addressof the subroutine is already known to the Microprocessor • Non Vectored: The device will have to supply the address of the subroutine to the Microprocessor Interrupt name Maskable Vectored INTR Yes No RST 5.5 Yes Yes RST 6.5 Yes Yes RST 7.5 Yes Yes TRAP No Yes
- 10. Representation of maskable and non-maskable interrupts
- 11. Non-maskable interrupt :Can not be delayed or Rejected. It’s types as follows. TARP: a non mask able interrupt known as NMI, it has the highest priority, it can not be enabled ; and it cannot be disable. It is edge and level triggered. This means hat the TRAP must go high and remain high until it is acknowledged. Maskable interrupt : Can be delayed or Rejected and Enable Or Disable By EI And DI Instruction. It’s types as follows. RST 7.5: The RST 7.5 interrupt is a maskable interrupt. It has the second highest priority. It is edge sensitive. ie. Input goes to high and no need to maintain high state until it recognized. Enabled by EI instruction. It is disabled by, 1.DI instruction 2.System or processor reset. 3.After reorganization of interrupt.
- 12. RST 6.5 and 5.5: The RST 6.5 and RST 5.5 both are level triggered. ie. Input goes to high and stay high until it recognized. Maskable interrupt. Enabled by EI instruction. It is disabled by, 1.DI, SIM instruction 2.System or processor reset. 3.After reorganization of interrupt. The RST 6.5 has the third priority whereas RST 5.5 has the fourth priority. INTR: INTR is a maskable interrupt. Enabled by EI instruction. It is disabled by, 1.DI, SIM instruction 2.System or processor reset. 3.After reorganization of interrupt. It is Non- vectored interrupt. After receiving INTA (active low) signal, it has to supply the address of ISR. It has lowest priority. It is a level sensitive interrupts. i.e. Input goes to high and it is necessary to maintain high state until it recognized. After receive this interrupt µp response with INTA pulse and it’s interrupt address is given by external circuit.
- 13. SIM(set interrupt mask) Instruction This is a multipurpose instruction and used to implement The 8085 interrupts 7.5, 6.5, 5.5, and serial data output. The instruction interrupts the accumulator contents as following:
- 14. RIM(Read Interrupt Mask) instruction: This is a multi purpose instruction used to read the Status of interrupts 7.5, 6.5 ,5.5 and read serial data input bit . The instruction loads eight bits in the accumulator with the following interpretations:
- 15. HARDWARE INTERRUPT BOCK DIAGRAM
- 16. SOFTWARE INTERRUPT The software interrupts are program instructions. These instructions are inserted at desired locations in a program. The 8085 has eight software interrupts from RST 0 to RST 7. When microprocessor is interrupt by giving instruction in the main program. The it is called as software interrupt. They allow the microprocessor to transfer program control from the main program to the subroutine program. After completing the subroutine program, the program control returns back to the main program. We can calculate the vector address of these interrupts using the formula given below: Vector Address = Interrupt Number * 8 For Example: RST2: vector address=2*8 = 16 RST1: vector address=1*8 = 08 RST3: vector address=3*8 = 24
- 17. Restart Instruction Equivalent to RST0 CALL 0000H RST1 CALL 0008H RST2 CALL 0010H RST3 CALL 0018H RST4 CALL 0020H RST5 CALL 0028H RST6 CALL 0030H RST7 CALL 0038H TABLE OF SOFTWARE INTERRUPT