Low-voltage Ride-through Methods for Grid-connected Photovoltaic Systems in Microgrids: A Review and Future Prospect

International Journal of Power Electronics and Drive System (IJPEDS)
Vol. 9, No. 4, December 2018, pp. 1834~1841
ISSN: 2088-8694, DOI: 10.11591/ijpeds.v9.i4.pp1834-1841  1834
Journal homepage: http://iaescore.com/journals/index.php/IJPEDS
Low-voltage Ride-through Methods for Grid-connected
Photovoltaic Systems in Microgrids: A Review and Future
Prospect
Haval Sardar Kamil1
, Dalila Mat Said2
, Mohd Wazir Mustafa3
, Mohammad Reza Miveh4
, Nasarudin
Ahmad5
1,2
Centre of Electrical Energy Systems (CEES), Universiti Teknologi Malaysia (UTM), Johor Bahru, Johor, Malaysia
1,2,3,5
School of Electrical Engineering, Universiti Teknologi Malaysia (UTM), Johor Bahru, Johor, Malaysia
4
Departement of Electrical Engineering, Tafresh University, Tafresh, Iran
Article Info ABSTRACT
Article history:
Received Jul 26, 2018
Revised Aug 26, 2018
Accepted Sep 9, 2018
Power quality is a concern for utility and grid operators due to a large
penetration of intermittent and stochastic renewable power generation
sources. One of the major concerns, when designing and controlling grid-
feeding photovoltaic (PV) inverters is meeting the grid requirements.
International grid requirements demand low-voltage ride-through (LVRT)
capability and maintaining grid functionality during fault conditions. This
paper presents a comprehensive review for several control techniques to
assure the LVRT capability of grid-feeding converters as well as discussing
their respective advantages and limitations in detail. Areas for further
research are identified afterwards. Finally, the conclusion gives a brief
summary and critique of the findings.
Keyword:
Control strategy
Grid-feeding power converter
Low-voltage ride-through
Photovoltaic (PV) inverter
Copyright © 2018 Institute of Advanced Engineering and Science.
All rights reserved.
Corresponding Author:
Dalila Mat Said,
Centre of Electrical Energy Systems (CEES), School of Electrical Engineering,
Universiti Teknologi Malaysia (UTM), Johor Bahru 81310, Johor, Malaysia.
Email: dalila@utm.my
1. INTRODUCTION
The global warming problem together with the environmental issues has already pushed the
governments to replace the conventional power plants with the renewable power generators with less
emission[1-4]. Among various renewable power sources, photovoltaic (PV) systems have been
commercialized in many countries for their industrial and environmental insight and their staggering grid
integration through the controllable converters to reach the sustainable development. PV systems normally
connected to the utility grid or microgrids using power electronic inverters to convert DC output power to
AC output power.
Based on conventional control methods, PV systems should be disconnected from microgrids during
grid faults conditions, due to the converter stability and protection. However, in recent years, a well-known
requirement has set for PV systems called low-voltage ride-through (LVRT) capability, which is been
applicable for other distributed generations regarding regenerative loads, compensation systems and energy
storage applications [5]. In other words, the PV systems must be able to stay in connected to the microgrid
for power quality enhancement under grid faults and to enhance voltage profile. The unregulated output
power of PV power station under abnormal conditions can be regulated through grid-friendly converters, and
the power system reliability can be guaranteed depending on the performance of these power converters.
Over the years, numerous LVRT control techniques have been proposed and introduced related to
renewable energy technologies, which is obvious from increasing growth of relevant papers that have been

Int J Pow Elec & Dri Syst ISSN: 2088-8694 
Low-voltage Ride-through Methods for Grid-connected Photovoltaic Systems in… (Haval Sardar Kamil)
1835
published in assorted journals and proceedings [6-13]. So that, it seems convenient at this juncture to provide
a comprehensive and cutting-edge review on existing LVRT control approaches of grid-feeding PV converter
in microgrids due to the initial steps in grid code applications for PV systems. This paper mainly outlines a
critical step that specifically deal with the latest research on LVRT methods which has been grown deeply, to
follow it effectively, it is envisaged that some background knowledge would be helpful for certain group of
readers. The remainder of this paper is structured as follows. Section 2 general control scheme for the grid-
feeding converter. Section 3 presents existing LVRT control approaches for grid-feeding PV inverters.
Discussion and future trends are given in Section 4. Finally, the conclusion is made in the last section.
2. GENERAL CONTROL STRUCTURE OF THREE-PHASE GRID-FEEDING POWER
CONVERTER
The general control structure for a three-phase grid-feeding converter is described in Figure 1. It
contains three main elements, including grid synchronization, inner loop control and outer loop control. It has
been exposed that the main superiority of grid-feeding power converter is involved being consistently
connected to the microgrid and avoiding islanding operation process.
Figure 1. General control structure for a three-phase grid-feeding converter
For controlling active and reactive powers flow, certain information regarding voltage phase angle,
amplitude and frequency is precisely required for the microgrid control system. However, identifying
information is the main objective of the grid synchronization method which required by the rest of the control
system. Despite a vast frame work range that have been proposed for synchronization strategies, the
synchronous reference frame phased locked loop (SRF-PLL) is extremely most well-known synchronization
method to be obtained [14].
Regarding the operation at the time of unbalanced grid voltage occurrence, normally identifying
phase angle and amplitude of voltage’s positive, negative and zero sequences are required for the
synchronization method process in microgrid system. However, identifying phase angle and amplitude of
different sequences at same instant of time is not yet being applied for grid-feeding power converters. Thus,
adding functionality to conventional synchronization method, or to implement techniques for separating
symmetrical components sequence under unbalanced conditions is a must. As the inner control loops are
controlling the PWM switching functionality of the converter and regulating the outer loops performance
limits accordingly, the inner loop controller is required to be fast and accurate[15]. Moreover, the inner loops
controller can be further designed to be in control of both the active and reactive power flow precisely.

 ISSN: 2088-8694
Int J Pow Elec & Dri Syst, Vol. 9, No. 4, December 2018 : 1834 – 1841
1836
3. AVAILABLE LVRT CONTROL APPROACHES FOR GRID-FEEDING PV INVERTER
UNDER UNBALANCED CONDITIONS
A simple process for the unbalanced three-phase current control which is inseparable of measured
currents into their individualized sequence components is proposed in [10]. The approach combines with a
classical synchronous frame of proportional integral (PI) regulators with boosted gains, to accomplish stellar
unbalanced three phase current control with a minimal complexity. Figure 2, illustrates the new scheme,
where the combined synchronous reference frame targeting sequence current references are being produced
by use of direct DC components, along with a twice frequency component from the adverse synchronous
reference frame (SRF). Hence, either controller works to balance both the positive sequence as well as
negative sequence currents at the instant time simultaneously, accordingly, these sequence currents would not
be required for separate extraction from the feedback signal measurement. The method frequently decreases
the current controller complexity, as the consequence, when the high potential gains of PI controller are used,
considerably enhances the efficient response of the current regulation technique.
Figure 2. Proposed unbalanced DG current control strategy [10]
Castilla et al. [11], presented a fully control strategy destined for synchronous compensators which
operate under abnormal faulty network situation. Particularly, the introduced control strategy proposes two
specific contributions, as novel reference generator of the reactive current and unprecedented voltage support
loop controller as well. Moreover, the reference generator of current has a main aspect capacity for supplying
the desired reactive current even while the voltage drops in amplitude throughout sag voltage. Hence, a
secure system operation is comfortably guaranteed by fixing the required limited current to the highest rated
current. The voltage loop controller due to setting two set points of voltage can perform various control
strategies. Furthermore, for this study three control schemes for voltage support have been carried out,
regardless to their merits and limitations.
In [16], the control strategy of both positive sequence and negative sequence components of the
large scale grid-connected PV system in critical unbalanced voltage sag situations in the network system is
deliberated. Some problems concerning system’s dynamic performance and stability occur while proportional
integral controllers are applied in current loops controller. However, delay is the purpose that the filtering
approach demands because of the voltage and current sequences extraction. Despite this delay, the system’s
dynamic response getting slower in respect to the situation when no filtration approach is required.
Moreover, there is a robust constraint on selecting appropriate parameters for the voltage and current loop
controllers without compromising circumstances of the stability of system.
The work by Du et al. [17], presenting the research study of instantaneous active and reactive power
fluctuation for three-phase grid-connected voltage source converter. Hence, the quadrature characteristics of
the fluctuated active and reactive power effects in the sine-term and cosine-term performances which are
merely resolved by the average active and reactive power correspondingly. Moreover, by the reason of
average active power and average reactive power decoupling effect to the oscillated power, the control
strategy of positive and negative sequence conductance and susceptance (PNGB) is proposed to manage and
control the grid fault events. The detailed correlations between control parameters of susceptance and
conductance with the power fluctuation amplitude and peak phase current have been derived. Hence, a
control approach to PNGB current has been introduced for regulating oscillated instantaneous active and

1837
reactive power. Furthermore, embedding current limitation strategy into the control loop for the sake of
overcurrent prevention.
In [5], the photovoltaic inverter controller which assures minimum peak values in injected currents
of the grid for the time of sag voltage is introduced. However, this method is established on the derived
algorithm. Additionally, the design technique is progressed beneficial to explore for the values of control
parameter where lessen the peak currents at the time of voltage sags of grid. A comprehensive mathematical
investigation of currents is implemented during the voltage sag for developing the proposed control design.
Regarding the evaluation of this control design performance, a detailed comparison obtained between
currents with the presented control scheme and the other control approaches is expressed as well. As the
encouraging aspect, reducing ripples in injected power at the time of sag occurrence is noticed, thereafter,
decreasing ripples in DC-link voltage, which would be critical in some particular situations.
The generalized control scheme of active power for DG inverter operates under unbalanced grid
disturbances is presented in [18]. On the basis of derived formulation and graphical illustration, the realized
contributions of symmetrical sequence elements to the instantaneous power and interactions among
symmetrical sequences is deeply elaborated. Due to proposing a flexible parameter between grid voltages and
reference currents, an effective technique is constructed to control the dc-link ripples and the symmetric
shape of the current or power factor concerning controllable fluctuated active and reactive powers.
Consequently, from the prospect of power electronic converter and power system the technique analysis is
being explained. In view of the flexible adaptivity of the proposed technique, it is permitted to collaborate
with various restraints in experiential layout.
In [19], various approaches that concern with controlling the distributed generation systems is
proposed in case of unbalanced situations that are brought on by faults in the utility network. Moreover, the
analytical consequences permit for designing the flexible controller of active power that can adjust itself for
faulty conditions and is more reconfigurable in terms of changing requirements of grid specially. In specific,
it is being validated that, throughout unbalanced events, there is a possibility for obtaining zero active and
reactive power oscillations only just by obtaining extremely high distorted currents. The work by Valouch et
al. [20], expresses the grid current control strategy at the level of power converter. The proffered analysis
takes charge of the control approach of positive and negative current sequences in the grid interconnected
converter at time of voltage sag. Moreover, the control strategy must ensure appropriate interchange of active
and reactive powers devoid of power ripple, harmonic distortion alleviation of grid currents, and should set
up grid currents peaks control additionally. A pure expression is resolved, which permits estimation of highly
exchangeable active and reactive powers between the converter and the grid without surpassing the allowable
converter current.
Shao et al. [21], have presented a transformerless three-level photovoltaic power converter and the
consequences of the unbalanced faults on the inverter’s neutral point for LVRT operation are figured out.
Moreover, new proposed control techniques are carried out to further balance the voltage oscillations on the
neutral point of the inverter under unbalanced faults. In [22], Ma and his research group investigate a three-
phase system, which offers six current control freedoms with a zero-sequence current path to alleviate both
active and reactive power fluctuations and inject sinusoidal currents as well. However, the constant dc source
has been used, the drawbacks of the unbalanced faults on the capacitive dc-link have not been investigated.
Cardenas et al. [23], assume that the dc-link voltage is to be constant. This assumption is inappropriate in
terms of the unbalanced fault as overall power would not be zero and the ripple would be produced to the dc-
link voltage. Afshari et al.[24], propose a model for PV source at the input side system, the performance of
the proposed technique is only evaluated through simulations. The proposed control strategy including two
operational modes, MPPT and non-MPPT modes, which they may operate under unbalanced conditions. The
authors of [25], illustrated the LVRT operation of current source grid-connected PV inverters under
unbalanced voltages. Moreover, the proposed method developed negative sequence current reference to
abolish active power double frequency fluctuations at the Ac side of the current source grid connected PV
inverter. Guo et al.[26], propose a new fault ride through FRT control strategy for grid connected inverters.
In the proposed method a pick current can control within the rated value effectually. A flexible control
strategy for three-phase PV inverters operating under unbalanced faults is discussed, nevertheless, the control
of the renewable energy source has not been explored.
4. DISCUSSION AND FUTURE TRENDS
The mentioned control strategies can be classified based on various consideration, as shown in
Table 1. As shown in the table, the control scheme of three-phase grid feeding power converters can be
designed in three different coordinate systems, which are the natural abc reference frame, the stationary αβo
reference frame, and the dq rotating frame. Various current controller techniques to the three-phase grid-

 ISSN: 2088-8694
1838
connected converters in three-phase three-wire systems has been proposed. A comparison of all the studies
about current control techniques is presented in Table 2. This comparative study listing the benefits and
drawbacks of each controller.
Table 1. Different Control Strategies for Grid-feeding PV Inverter
References
Reference
frame
Active-reactive
power control
Reference
current
generator
Inner current
control
Synchronization
Method
Target
(Sosa et al.,
2016)
Stationary
reference
frame
Active/reactive
power injection
Controllable
active power
oscillation
Proportional-
Resonant (PR)
PLL
Three-phase
three-wire system
(Chen et al.,
2016)
Synchronous
reference
frame
Active/reactive
power injection
Controllable
active power
oscillation
Proportional-
Integral (PI)
PLL
Three-phase
three-wire system
(Rodríguez et
al., 2015)
Stationary
reference
frame
Active/reactive
power injection
Disconnection PR
DSOGI-FLL,
(FLL)
Three-phase
three-wire system
(Kou et al.,
2015)
abc frame
Active/reactive
power injection
Controllable
active power
oscillation
PI -
Three-phase
three-wire system
(Mirhosseini et
al., 2015)
Synchronous
reference
frame
P=0, Q=0 Disconnection PI
Moving average
filters (MAFs)
Three-phase
three-wire system
(Kabiri et al.,
2015)
Synchronous
reference
frame
P=0, Q=0 Disconnection PI PLL
Three-phase
three-wire system
(Castilla et al.,
2014)
Stationary
reference
frame
Positive/negative
sequence reactive
power injection
- PI PLL
Three-phase
three-wire system
(Du et al.,
2016)
Synchronous
reference
frame
active/reactive
power injection
Controllable
active/reactive
power
oscillation
Conductance /
saucepans control
scheme
-
Three-phase
three-wire system
(Miret et al.,
2012)
abc frame
Positive/negative
sequence reactive
power injection
- PI PLL
Three-phase
three-wire system
(Wang et al.,
2012)
Stationary
reference
frame
Positive sequence
active power
injection
- PR
Sequence
detection
Three-phase
three-wire system
(Rodriguez et
al., 2007)
Synchronous
reference
frame,
Stationary
reference
frame
Positive/negative
sequence reactive
power injection
Controllable
active/reactive
power
oscillation
PI, PR
second-order
generalized
integrator
bandpass filter
(SOGI-BPF)
Three-phase
three-wire system
(Valouch et al.
2015)
Synchronous
reference
frame
Positive/negative
sequence reactive
power injection
Controllable
active/reactive
power
oscillation
PI PLL
Three-phase
three-wire system
Table 2. Benefits and Limitations of Control Structures
Control
strategies
Associated controller
type
Advantage Disadvantage
dq frame PI
Easy hardware implementation
Simple current control
Good dynamic response
Fixed switching frequency
Very poor harmonics compensation
Steady-state error is not eliminated
abc frame
PI Fixed switching frequency
Complex transfer function
Slow dynamic response
PR Fixed switching frequency
More complex with refer to hysteresis
and dead-beat
αβ frame
PR
High gain around resonance frequency
Steady-state error omitting is very good
High dynamic response
Good current harmonic compensation especially
low-order
Complex hardware implementation
Slow dynamic response with DC
signals
RC
High gain at the integral multiples of the
fundamental frequency
High order harmonics compensator
Variable switching frequency

1839
The active and reactive power control, reference current generator, current controller and the
synchronization method for each strategy is presented in the last section as well. Regarding the literature,
previous research in this specific field have only focused on the control of three-phase grid-feeding
converters under unbalanced situations in three-wire systems. Nevertheless, far too little consideration has
been paid to the control of such kind grid-connected inverters in three-phase four-wire systems. It is due to
the reality that the positive, negative and zero sequence components should be organized and handled in
three-phase four-wire systems simultaneously, which is resulting in a complex control algorithm.
The current control of the grid-feeding converters in three phase three-wire systems under
unbalanced grid-fault conditions is a well-developed and mature research topic. Nonetheless, far too little
attention has been paid to current control of the grid-feeding power converters in three-phase four-wire
islanded microgrids due to presence of positive, negative as well as zero sequence components. On the basis
of the previous studies, the current control techniques for grid-feeding power converters operating in the
three-phase four-wire systems often suffering from slow transient response and complicated control
algorithm. Therefore, it is important to propose an improved current control technique for three phase grid-
feeding power converter operating in three-phase four-wire islanded microgrid for compensating positive,
negative and zero sequence component with fast dynamic response and simple control structure.
Furthermore, the phase angle and magnitude of positive, negative and zero sequence voltage components in
four-wire network typically used for synchronization of grid-feeding converter output variables, calculation
of power flow or transformation of stationery variable components into rotating reference frames. Hence,
grid synchronization of grid-feeding power converters operating in the three-phase four-wire islanded
microgrid is an essential.
5. CONCLUSION
In this paper, the recently published papers about LVRT control methods for grid-feeding PV
inverters operating under unbalanced conditions in microgrids were assessed and investigated as a
comprehensive review. Multi-purpose PV inverters have fascinated increasing concern for their contributions
to ancillary services for the enhancement of power quality in the stand-alone and autonomous distribution
systems. The presented LVRT control techniques classified based on various applications, including type of
inverters, control schemes, and control adjustment. In order to improve power quality and stability in
islanded microgrid different control schemes have conferred and compared in detail. This paper is expected
to be a useful reference for researchers, engineers and manufacturers involved in PV systems.
ACKNOWLEDGEMENTS
The authors wish to acknowledge the Ministry of Education, Malaysia and Universiti Teknologi
Malaysia for supporting this research under Grant QJ130000.2423.03G88.
REFERENCES
[1] L. Naik, "Design and Performance of a PV-STATCOM for Enhancement of Power Quality in Micro Grid
Applications," International Journal of Power Electronics and Drive Systems (IJPEDS), vol. 8, no. 3, pp. 1408-
1415, 2017.
[2] S. K. Bhuyan, P. K. Hota, and B. Panda, "Power Quality Analysis of a Grid-connected Solar/Wind/Hydrogen
Energy Hybrid Generation System," International Journal of Power Electronics and Drive Systems (IJPEDS), vol.
9, no. 1, pp. 377-389, 2018.
[3] A. Naderipour, A. M. Zin, M. Habibuddin, M. Moradi, M. Miveh, and H. Afrouzi, "A new compensation control
strategy for grid-connected wind turbine and fuel cell inverters in a microgrid," International Journal of Power
Electronics and Drive Systems (IJPEDS), vol. 8, no. 1, pp. 272-278, 2017.
[4] H. S. Kamil, D. M. Said, M. W. Mustafa, M. R. Miveh, N. Rosmin, and N. Ahmad, "DIgSILENT modelling of a
four-leg power converter using a triangular carrier wave," in Energy Conversion (CENCON), 2017 IEEE
Conference on, 2017, pp. 343-348: IEEE.
[5] J. Miret, M. Castilla, A. Camacho, L. G. de Vicuña, and J. Matas, "Control scheme for photovoltaic three-phase
inverters to minimize peak currents during unbalanced grid-voltage sags," IEEE transactions on Power Electronics,
vol. 27, no. 10, pp. 4262-4271, 2012.
[6] H.-C. Chen, C.-T. Lee, P.-T. Cheng, R. Teodorescu, and F. Blaabjerg, "A low-voltage ride-through technique for
grid-connected converters with reduced power transistors stress," IEEE Transactions on Power Electronics, vol. 31,
no. 12, pp. 8562-8571, 2016.
[7] N. Guerrero-Rodríguez, A. B. Rey-Boué, L. C. Herrero-de Lucas, and F. Martinez-Rodrigo, "Control and
synchronization algorithms for a grid-connected photovoltaic system under harmonic distortions, frequency
variations and unbalances," Renewable Energy, vol. 80, pp. 380-395, 2015.

 ISSN: 2088-8694
1840
[8] W. Kou, D. Wei, P. Zhang, and W. Xiao, "A direct phase-coordinates approach to fault ride through of unbalanced
faults in large-scale photovoltaic power systems," Electric Power Components and Systems, vol. 43, no. 8-10, pp.
902-913, 2015.
[9] M. Mirhosseini, J. Pou, and V. G. Agelidis, "Single-and two-stage inverter-based grid-connected photovoltaic
power plants with ride-through capability under grid faults," IEEE Trans. Sustain. Energy, vol. 6, no. 3, pp. 1150-
1159, 2015.
[10] R. Kabiri, D. Holmes, and B. McGrath, "Double synchronous frame current regulation of distributed generation
systems under unbalanced voltage conditions without sequence current separation," in Applied Power Electronics
Conference and Exposition (APEC), 2015 IEEE, 2015, pp. 1822-1829: IEEE.
[11] M. Castilla, J. Miret, A. Camacho, J. Matas, and L. G. de Vicuña, "Voltage support control strategies for static
synchronous compensators under unbalanced voltage sags," IEEE transactions on industrial electronics, vol. 61, no.
2, pp. 808-820, 2014.
[12] M. R. Miveh, M. F. Rahmat, A. A. Ghadimi, and M. W. Mustafa, "Power quality improvement in autonomous
microgrids using multi-functional voltage source inverters: a comprehensive review," Journal of Power Electronics,
vol. 15, no. 4, pp. 1054-1065, 2015.
[13] J. L. Sosa, M. Castilla, J. Miret, J. Matas, and Y. Al-Turki, "Control strategy to maximize the power capability of
PV three-phase inverters during voltage sags," IEEE Transactions on Power Electronics, vol. 31, no. 4, pp. 3314-
3323, 2016.
[14] N. Jaalam, N. Rahim, A. Bakar, C. Tan, and A. M. Haidar, "A comprehensive review of synchronization methods
for grid-connected converters of renewable energy source," Renewable and Sustainable Energy Reviews, vol. 59,
pp. 1471-1481, 2016.
[15] T. L. Vandoorn, J. C. Vasquez, J. De Kooning, J. M. Guerrero, and L. Vandevelde, "Microgrids: Hierarchical
control and an overview of the control and reserve management strategies," IEEE industrial electronics magazine,
vol. 7, no. 4, pp. 42-55, 2013.
[16] M. Mirhosseini, J. Pou, B. Karanayil, and V. G. Agelidis, "Positive-and negative-sequence control of grid-
connected photovoltaic systems under unbalanced voltage conditions," in Power Engineering Conference
(AUPEC), 2013 Australasian Universities, 2013, pp. 1-6: IEEE.
[17] X. Du, Y. Wu, S. Gu, H.-M. Tai, P. Sun, and Y. Ji, "Power oscillation analysis and control of three-phase grid-
connected voltage source converters under unbalanced grid faults," IET Power Electronics, vol. 9, no. 11, pp. 2162-
2173, 2016.
[18] F. Wang, J. Duarte, and M. Hendrix, "Design and analysis of active power control strategies for distributed
generation inverters under unbalanced grid faults," IET generation, transmission & distribution, vol. 4, no. 8, pp.
905-916, 2010.
[19] P. Rodriguez, A. V. Timbus, R. Teodorescu, M. Liserre, and F. Blaabjerg, "Flexible active power control of
distributed power generation systems during grid faults," IEEE Transactions on Industrial Electronics, vol. 54, no.
5, pp. 2583-2592, 2007.
[20] V. Valouch, M. Bejvl, P. Šimek, and J. Škramlík, "Power control of grid-connected converters under unbalanced
voltage conditions," IEEE Transactions on Industrial Electronics, vol. 62, no. 7, pp. 4241-4248, 2015.
[21] Z. Shao, X. Zhang, F. Wang, R. Cao, and H. Ni, "Analysis and control of neutral-point voltage for transformerless
three-level PV inverter in LVRT operation," IEEE Transactions on Power Electronics, vol. 32, no. 3, pp. 2347-
2359, 2017.
[22] K. Ma, W. Chen, M. Liserre, and F. Blaabjerg, "Power controllability of a three-phase converter with an
unbalanced AC source," IEEE Transactions on Power Electronics, vol. 30, no. 3, pp. 1591-1604, 2015.
[23] R. Cárdenas, M. Díaz, F. Rojas, J. Clare, and P. Wheeler, "Resonant control system for low-voltage ride-through in
wind energy conversion systems," IET Power Electronics, vol. 9, no. 6, pp. 1297-1305, 2016.
[24] E. Afshari, B. Farhangi, Y. Yang, and S. Farhangi, "A low-voltage ride-through control strategy for three-phase
grid-connected PV systems," in Power and Energy Conference at Illinois (PECI), 2017 IEEE, 2017, pp. 1-6: IEEE.
[25] Z. Wang, B. Wu, D. Xu, M. Cheng, and L. Xu, "Dc-link current ripple mitigation for current-source grid-connected
converters under unbalanced grid conditions," IEEE Transactions on Industrial Electronics, vol. 63, no. 8, pp. 4967-
4977, 2016.
[26] X. Guo, W. Liu, and Z. Lu, "Flexible power regulation and current-limited control of the grid-connected inverter
under unbalanced grid voltage faults," IEEE Transactions on Industrial Electronics, vol. 64, no. 9, pp. 7425-7432,
2017.

1841
BIOGRAPHIES OF AUTHORS
Haval Sardar Kamil received his B.Sc. (Electrical Engineering) and M. Tech. (Electrical Power
Engineering) in 2007 and 2013 repectively. He is currently pursuing a Ph.D. degree (Electrical
Engineering) at the School of Electrical Engineering, Universiti Teknologi Malaysia (UTM). His
research interest includes distributed generation, microgrid, and renewable energy systems.
Dalila Mat Said is a Senior Lecturer at Centre of Electrical Energy Systems, School of Electrical
Engineering, Universiti Teknologi Malaysia (UTM). She has 13 years of experience in teaching
electrical engineering courses and supervision of more than 30 undergraduates, and 15 post
graduate’s students. She has an experience within the area of power quality consultancy. She was
involved in the Power Quality Baseline Study in a Peninsular Malaysia (2010-2013) under the
Energy Commission of Malaysia. She is a member of IEM, IET and IEEE
Mohd Wazir Mustafa received his B.S. Degree (1988), M. Sc. (1993) and PhD (1997) from
University of Strathclyde. He is currently a Professor and Chair of School of Electrical
Engineering, Universiti Teknologi Malaysia (UTM), Johor Bahru, Malaysia. His research
interest includes power system stability, FACTS and power system distribution automation,
deregulated power system, etc. He is a professional engineer of IEEE
Mohammad Reza Miveh received his Ph.D. (Electrical Engineering) from Universiti Teknologi
Malaysia (UTM) in 2017. Currently, he is Assistant Professor in Department of Electrical
Engineering at Tafresh University, Tafresh, Iran. His research interests are in the area of
microgrid, distributed generation, fuel cell and simulation and analysis of power system.
Nasarudin Ahmad received B. Sc and M. Sc degrees in electrical engineering from Universiti
Teknologi Malaysia, in 1998 and 2000 respectively. Since 2000 he has been a lecturer in School
of Electrical Engineering, Universiti Teknologi Malaysia. His interest in research activities are
application of instrumentation technique in power system

Low-voltage Ride-through Methods for Grid-connected Photovoltaic Systems in Microgrids: A Review and Future Prospect

More Related Content

What's hot (20)

Similar to Low-voltage Ride-through Methods for Grid-connected Photovoltaic Systems in Microgrids: A Review and Future Prospect (20)

More from International Journal of Power Electronics and Drive Systems (20)

Recently uploaded (20)

Low-voltage Ride-through Methods for Grid-connected Photovoltaic Systems in Microgrids: A Review and Future Prospect