An efficient multi resolution filter bank based on da based multiplication

International Journal of VLSI design & Communication Systems (VLSICS) Vol.5, No.3, June 2014
DOI : 10.5121/vlsic.2014.5307 73
AN EFFICIENT MULTI RESOLUTION FILTER
BANK BASED ON DA BASED MULTIPLICATION
Namitha Jose M1
and U Hari2
1
PG student Department of ECE
2
Asst. Professor Department of ECE
ABSTRACT
Multi-resolution filter bank (MRFB)-based on the fast filter bank design can be used for multiple resolution
spectrum sensing. MRFB overcomes the constraint of fixed sensing resolution in spectrum sensors based
on conventional discrete Fourier transform filter banks (DFTFB) without hardware re-implementation.
Multipliers have a greater impact on complexity and performance of the design because a large number of
constant multiplications are required in the multiplication of filter coefficients with the filter input.
Modified multiplier architecture Distributed Arithmetic(DA) is used to improve the efficiency
KEYWORDS
Filter Bank, MRFB, Multipliers, DA Based Multiplication
1. INTRODUCTION
A filter bank is an array of band-pass filters that separates the input signal into multiple
components. Signal processing systems needs more room to store data during the processing,
transmission and reception. In order to reduce the data to be processed, save storage and lower
the complexity, multi rate sampling techniques were introduced to achieve these goals. The
conventional method for sensing the multiple bandwidth channels is to have a fixed sensing
resolution using discrete Fourier transform filter banks (DFTFB), where resolution is fixed as per
the bandwidth of the channel that has the smallest bandwidth among all the channels of multiple
standards. This method will sense a wider bandwidth channel by adding together the smaller
bands of fixed resolution. But when the input signal is having channels of varying bandwidths,
the conventional method of fixed sensing using the smallest sensing resolution becomes complex
as the method needs to utilize the most stringent specification for a relaxed bandwidth. This will
increase the dynamic power and delay in obtaining the output. The proposed MRFB-based
spectrum sensor can adapt to different sensing detection bandwidths for wideband spectrum
sensing without hardware re-implementation.
The proposed MRFB for spectrum sensing is a low complexity filter design approach based on
FFB [2], with variable sensing resolution.FFB is a low complexity filter bank [2], proposed as an
alternative to DFTFBs. The FFB consists of several sub filters of lower order arranged in a tree
fashion. The FFB makes use of a technique called as frequency response masking (FRM) [4]. The
basic idea behind the FRM technique [4] is to compose the overall sharp transition-band filter

74
using several wide transition-band sub filters. However, the reconfigurability potential of FFB is
hardly exploited in literature. In the proposed MRFB architecture, we modify the FFB design, by
incorporating reconfigurability to each of the sub filters for varying the sensing resolution in MR.
FFT provides the means to reduce the computational complexity of the DFT from order (N2
) to
order (N log2(N)), it is often desirable to do FFT-based processing for DSP systems.
A. Dft Fb
DFB[7] consists of a set of filter banks as shown in the figure. The process of decomposition
performed by the filter bank is called analysis (meaning analysis of the signal in terms of its
components in each sub-band); the output of analysis is referred to as a sub band signal with as
many sub bands as there are filters in the filter bank. The reconstruction process is called
synthesis, meaning reconstitution of a complete signal resulting from the filtering process.
But the disadvantage of the DFB is that all the filter banks should be active for all the time and
the resolution also should be maintained according to the smallest bandwidth.
Fig. 1: Basic Block Diagram of a DFT based Filter Bank

75
Fig. 2: MRFB Architecture
TABLE I
USING MRFB FOR RE-CONFIGURABILITY WITH SELECT(S) AND ENABLE(EN) SIGNALS
S[1:0] En[0:2] No. of Channels
11 111 16(BW=0.05)
10 110 4(BW=0.1)
01 100 2(BW=0.2)
00 000 1(BW=0.4)
B. Multi Resolution Filter
The FFB is suitable for the design of filter banks due to its reduced complexity [2]. The FFB
follows a tree structure and it can be decomposed into several stages. For a k-stage FFB, we can
realize 2k
channels. The sub filters Hij(z), where j > 0 are modulated versions of prototype filter
and together they form the basic structure of FFB .Each stage is interpolated by a factor M and
we can get both the original and complementary responses from each stage. A complementary
filter can be obtained by subtracting the output of the (M+1) band response from a suitably
delayed version of the input. If each of these (M+1) bands is masked using suitably designed

76
masking filters in k-1 stages, we can obtain 2k
channels. In this paper, reconfigurabilty is
incorporated into FFB architecture so that the filter response can be changed by varying the
interpolation value according to the resolution required in the spectrum sensor. Using the
proposed spectrum sensor, the sensing resolution can also be changed using software
reconfiguration.
Figure 2 shows an 8-channel MRFB architecture and Table I describe how channel bandwidth is
modified with select (S) and enable signals (En).
Fig. 3: Reconfigurable Filter Architecture for first stage
The length of the filters can be obtained from the expression (1).
(1)
The reconfigurable architecture for the first stage is shown in Fig 3. The FFB is realized in the
form of a system of filters organized in a parallel tree structure.
2. MODIFIED MULTIPLIER ARCHITECTURE
Multipliers are one of the most important arithmetic units in filter banks. Due to their complex
structure multipliers are the major source of power dissipation in such systems. The speed of
multiplier also limits the system performance. With the advance of VLSI technology, the size of
transistors becoming smaller and smaller, so that more number of transistors can be integrated
into same silicon area to achieve high functionality density and performance. On the other hand
higher transistor density also leads to higher power density. Various research works aiming at
reducing the power consumption or the speed have been reported.
3. DISTRIBUTED ARITHMETIC BASED MULTIPLICATION
The multiplier block of the digital FIR filter in its transposed form involves the multiplication of
filter coefficients with the filter input [11].

77
Fig. 4: DA Block Diagram
The multiplication of filter coefficients with the input data is generally implemented under a shift
adds architecture where each constant multiplication is realized using addition/subtraction and
shift operations in an MCM operation[12]. The basic idea is to replace all multiplications and
additions by a table and a shifter-accumulator.
(2)
(3)
DA relies on the fact that the filter coefficients are known, so multiplying c[n]x[n] becomes a
multiplication with a constant.
Fig. 5: Baugh Woolean Algorithm

78
4. SIMULATION AND COMPARISON RESULTS
The programs for 8 channel DFB, MRFB, Baugh Woolean Multiplier Based MRFB are designed
using Verilog codes and each filter bank is compiled using Model SIM and simulated to verify
their outputs and the simulation results are shown in Fig 6, 7, 8.The codes are synthesized in
Cadence RTL compiler using typical libraries of TSMC 0.18 um technology and area and power
analysis was done.
The table II shows the comparison of area, delay and power of the three different types of filter
bank implementations. From the table II, the area and power of the proposed Modified multiplier
Based MRFB is much less than that of the existing systems. Fig 6 and 7 shows the area and
power comparisons of different filter bankss.
Fig. 6: Simulated Result for DFB
Fig. 7: Simulated Result for MRFB

79
Fig. 8: Simulated Result for MRFB with modified multiplier

80
Fig. 9: Comparison plots of DFB, MRFB, Modified MRFB
TABLE II
COMPARISON OF AREA, DELAY AND POWER
DFTFB Proposed MRFB MRFB with
Modified Multiplier
Area (Number of Les) 1140 1052 670
Delay(s) 1.249531 x 10^-8 1.005126 x 10^-8 0.7620001x 10^-8
Power (nW) 1763211.53 1365499.92 1001491.02
In this paper, an efficient Multi Resolution Filter Bank is proposed by modifying the multiplier
design based on Distributed Arithmetic .This can replace the multiplier which are more
prominent in the convolution operations with shift and add mechanism. In this way, the transistor
count can be reduced to a greater extend and hence the power. In the case of 8 bit MRFB the area
has been reduced to 1052 from 1140 of DFB. In DA Based MRFB it is further reduced to 670.
From the results it can be seen that the area, power and delay of the DA based MRFB is much
less than that of DFB and the normal MRFB.
REFERENCES
[1] G. Smitha and A. P. Vinod., “A Multi-Resolution Fast Filter Bank for Spectrum Sensing in Military
Radio Receivers “IEEE Transactions On Very Large Scale Integration (VLSI) Systems, VOL. 20,
NO. 7, JULY 2012
[2] Y. C. Lim and B. F-Boroujeny, “Fast filter bank (FFB),” IEEE Trans.Circuits Syst. II, Exp. Briefs,
vol. 39, no. 5, pp. 316–318, May 1992.
[3] Y. C. Lim and B. F-Boroujeny, “Analysis and optimum design of the FFB,” in Proc. Int. Symp.
Circuits Syst., 1994, pp. 509–512.
[4] Y. C. Lim, “Frequency-response masking approach for the synthesis of sharp linear phase digital
filters,” IEEE Trans. Circuits Syst., vol. 33,no. 4, pp. 357–364, Apr. 1986.
[5] Xingguo Xiong, Muzi Lin “Low Power 8-Bit Baugh–Wooley Multiplier Based on Wallace Tree
Architecture”, Emerging Trends in Computing, Informatics, Systems Sciences, and Engineering
Lecture Notes in Electrical Engineering Volume 151, 2013, pp 851-865
[6] M. Sjalander et al., .An Efficient Twin-Precision Multiplier,. in Proc.Intl Conf. on Computer Design
(ICCD), Oct. 2004, pp. 30.331.
[7] Sheikh and B. Bing, “Cognitive spectrum sensing and detection using polyphase DFT filter banks,” in
Proc. IEEE Consumer Commun.Network. Conf., 2008, pp. 973–977

81
[8] W. A. Abu-Al-Saud and G. L. Stuber, “Efficient wideband channelizer for software radio systems
using modulated PR filter banks,” IEEE Trans. Signal Process., vol. 52, no. 10, pp. 2807–2820, Oct.
2004.
[9] Y. Hur, L. Park, W.Woo, K. Lim, C.-H. Lee, H. S. Kim, and L. Laskar,“A wideband analog multi-
resolution spectrum sensing (MRSS) technique,” in Proc. Int. Symp. Circuits Syst., 2006, pp. 4090–
4093.
[10] Levent Aksoy, Cristiano Lazzari, Eduardo Costa,Paulo Flores and José Monteiro, Design of Digit-
Serial FIR Filters: Algorithms,Architectures, and a CAD Tool , IEEE TRANSACTIONS ON VERY
LARGE SCALE INTEGRATION (VLSI) SYSTEMS, VOL. 21, NO. 3, MARCH 2013
[11] Yu-Chi Tsao and Ken Choi, Area-Efficient Parallel FIR Digital Filter Structures for Symmetric
Convolutions Based on Fast FIR Algorithm, IEEE TRANSACTIONS ON VERY LARGE SCALE
INTEGRATION (VLSI) SYSTEMS, VOL. 20, NO. 2, FEBRUARY 2012

An efficient multi resolution filter bank based on da based multiplication

More Related Content

What's hot (17)

Viewers also liked (17)

Similar to An efficient multi resolution filter bank based on da based multiplication (20)

Recently uploaded (20)

An efficient multi resolution filter bank based on da based multiplication